Currently, all the time limits in the bonding ARP monitor are in
multiples of arp_interval -- the time interval at which the ARP
monitor is periodically scheduled.
With a fast network round-trip and a little scheduling latency
of the ARP monitor work, a limit of n*delta_in_ticks may
effectively mean (n-1)*delta_in_ticks.
This is fatal in case of n==1 (the link will stay down
forever) and makes the behaviour non-deterministic in all the
other cases.
Add a delta_in_ticks/2 time slack to all the time limits.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the "bonding" driver does not support load balancing outgoing
traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4)
are currently supported; this patch adds transmit hashing for IPv6 (and
TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the
bonding driver. In addition, bounds checking has been added to all
transmit hashing functions.
The algorithm chosen (xor'ing the bottom three quads of the source and
destination addresses together, then xor'ing each byte of that result into
the bottom byte, finally xor'ing with the last bytes of the MAC addresses)
was selected after testing almost 400,000 unique IPv6 addresses harvested
from server logs. This algorithm had the most even distribution for both
big- and little-endian architectures while still using few instructions. Its
behavior also attempts to closely match that of the IPv4 algorithm.
The IPv6 flow label was intentionally not included in the hash as it appears
to be unset in the vast majority of IPv6 traffic sampled, and the current
algorithm not using the flow label already offers a very even distribution.
Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets,
ie, they are not balanced based on layer 4 information. Additionally,
IPv6 packets with intermediate headers are not balanced based on layer
4 information. In practice these intermediate headers are not common and
this should not cause any problems, and the alternative (a packet-parsing
loop and look-up table) seemed slow and complicated for little gain.
Tested-by: John Eaglesham <linux@8192.net>
Signed-off-by: John Eaglesham <linux@8192.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although this doesn't matter actually, because netpoll_tx_running()
doesn't use the parameter, the code will be more readable.
For team_dev_queue_xmit() we have to move it down to avoid
compile errors.
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the previous patch, slave_disable_netpoll() and __netpoll_cleanup()
may be called with read_lock() held too, so we should make them
non-block, by moving the cleanup and kfree() to call_rcu_bh() callbacks.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't see any benifits to use netdev_bonding_change() than
using call_netdevice_notifiers() directly.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now number of tx queues can be specified during bond instance
creation and therefore it may differ from params.tx_queues, use rather
real_num_tx_queues for boundary check.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also cut out unused function parameters and possible err in return
value.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some workloads greatly benefit of IFF_XMIT_DST_RELEASE capability
on output net device, avoiding dirtying dst refcount.
bonding currently disables IFF_XMIT_DST_RELEASE unconditionally.
If all slaves have the IFF_XMIT_DST_RELEASE bit set, then
bonding master can also have it in its priv_flags
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding debugfs support has been broken in the presence of network
namespaces since it has been added. The debugfs support does not handle
multiple bonding devices with the same name in different network
namespaces.
I haven't had any bug reports, and I'm not interested in getting any.
Disable the debugfs support when network namespaces are enabled.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently reported that moving a bonding device between network
namespaces causes warnings from /proc. It turns out after the move we
were trying to add and to remove the /proc/net/bonding entries from the
wrong network namespace.
Move the bonding /proc registration code into the NETDEV_REGISTER and
NETDEV_UNREGISTER events where the proc registration and unregistration
will always happen at the right time.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four link statuses of a bonding slave, the procfs
code shows a wrong status when using downdelay/updelay:
(slave->link == BOND_LINK_UP) ? "up" : "down"
It doesn't respect the rest two statuses. This patch fixes it.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets are dropped in TX path, its better to use kfree_skb()
instead of dev_kfree_skb() to give proper drop_monitor events.
Also move the kfree_skb() call after read_unlock() in bond_alb_xmit()
and bond_xmit_activebackup()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cloning all packets in input path have a significant cost.
Use skb_header_pointer()/skb_copy_bits() instead of pskb_may_pull() so
that recv_probe handlers (bond_3ad_lacpdu_recv / bond_arp_rcv /
rlb_arp_recv ) dont touch input skb.
bond_handle_frame() can avoid the skb_clone()/dev_kfree_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Jiri Bohac <jbohac@suse.cz>
Cc: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Cc: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping. This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.
When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit. In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.
Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping. In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.
If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)
This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :
netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.
Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.
Based on a previous patch from Tom Herbert.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Tom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we modify primary via sysfs and it is not a valid slave,
we should record it for future use, and this behavior is the same with
bond_check_params().
Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I applied the wrong version of Jiri's bonding fix in commit
13a8e0c8cd ("bonding: don't increase
rx_dropped after processing LACPDUs")
I applied v3, which introduces warnings I asked him to fix,
instead of v4 which properly takes care of those issues.
This inter-diffs such that the warnings are now gone.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal_64bits to add
some clarity and reduce the likelihood for misuse of
compare_ether_addr_64bits for sorting.
Done via cocci script:
$ cat compare_ether_addr_64bits.cocci
@@
expression a,b;
@@
- !compare_ether_addr_64bits(a, b)
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- compare_ether_addr_64bits(a, b)
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !ether_addr_equal_64bits(a, b) == 0
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !ether_addr_equal_64bits(a, b) != 0
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- ether_addr_equal_64bits(a, b) == 0
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- ether_addr_equal_64bits(a, b) != 0
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal_64bits(a, b)
+ ether_addr_equal_64bits(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3aba891d, bonding processes LACP frames (802.3ad
mode) with bond_handle_frame(). Currently a copy of the skb is
made and the original is left to be processed by other
rx_handlers and the rest of the network stack by returning
RX_HANDLER_ANOTHER. As there is no protocol handler for
PKT_TYPE_LACPDU, the frame is dropped and dev->rx_dropped
increased.
Fix this by making bond_handle_frame() return RX_HANDLER_CONSUMED
if bonding has processed the LACP frame.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
As none of the callers of bond_update_speed_duplex (need to) check its
return value, there is little point in it returning anything.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize slave device link state as down if ARP monitor is
active and net_carrier_ok() returns zero. Also shift initial
value of its last_arp_tx so that it doesn't immediately cause
fake detection of "up" state.
When ARP monitoring is used, initializing the slave device with
up link state can cause ARP monitor to detect link failure
before the device is really up (with igb driver, this can take
more than two seconds).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change get_tx_queues, drop unsused arg/return value real_tx_queues,
and use return by value (with error) rather than call by reference.
Probably bonding should just change to LLTX and the whole get_tx_queues
API could disappear!
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.
To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.
Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7d26bb103c "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.
Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.
How to reproduce this bug ?
-----------hostB----------------
hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)|
(192.168.100.1/24 \--|-- eth1-/ |
--------------------------------
1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1
then eth0 is the active slave, and MAC of bond0 is MAC of eth0.
2 on hostA, ping 192.168.100.2
3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.
4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
The following patch aimed to resolve an issue where secondary, tertiary,
etc. addresses added to bond interfaces could overwrite the
bond->master_ip and vlan_ip values.
commit 917fbdb32f
Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Date: Wed Nov 23 23:37:15 2011 +0000
bonding: only use primary address for ARP
That patch was good because it prevented bonds using ARP monitoring from
sending frames with an invalid source IP address. Unfortunately, it
didn't always work as expected.
When using an ioctl (like ifconfig does) to set the IP address and
netmask, 2 separate ioctls are actually called to set the IP and netmask
if the mask chosen doesn't match the standard mask for that class of
address. The first ioctl did not have a mask that matched the one in
the primary address and would still cause the device address to be
overwritten. The second ioctl that was called to set the mask would
then detect as secondary and ignored, but the damage was already done.
This was not an issue when using an application that used netlink
sockets as the setting of IP and netmask came down at once. The
inconsistent behavior between those two interfaces was something that
needed to be resolved.
While I was thinking about how I wanted to resolve this, Ralf Zeidler
came with a patch that resolved this on a RHEL kernel by keeping a full
shadow of the entries in dev->ifa_list for the bonding device and vlan
devices in the bonding driver. I didn't like the duplication of the
list as I want to see the 'bonding' struct and code shrink rather than
grow, but liked the general idea.
As the Subject indicates this patch drops the master_ip and vlan_ip
elements from the 'bonding' and 'vlan_entry' structs, respectively.
This can be done because a device's address-list is now traversed to
determine the optimal source IP address for ARP requests and for checks
to see if the bonding device has a particular IP address. This code
could have all be contained inside the bonding driver, but it made more
sense to me to EXPORT and call inet_confirm_addr since it did exactly
what was needed.
I tested this and a backported patch and everything works as expected.
Ralf also helped with verification of the backported patch.
Thanks to Ralf for all his help on this.
v2: Whitespace and organizational changes based on suggestions from Jay
Vosburgh and Dave Miller.
v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's
suggestion.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Ralf Zeidler <ralf.zeidler@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Liang Zheng(lzheng@redhat.com) found that in the following topo,
bonding does not send igmp report when we trigger a fail-over of bonding.
eth0--
|-- bond0 -- br0
eth1--
modprobe bonding mode=1 miimon=100 resend_igmp=10
ifconfig bond0 up
ifenslave bond0 eth0 eth1
brctl addbr br0
ifconfig br0 192.168.100.2/24 up
brctl addif br0 bond0
Add 192.168.100.2(br0) into a multicast group, like 224.10.10.10,
then trigger a fali-over in bonding.
You can see that parameter "resend_igmp" does not work.
The reason is that when we add br0 into a multicast group,
it does not propagate multicast knowledge down to its ports.
If we choose to propagate multicast knowledge down to all ports for bridge,
then we have to track every change that is done to bridge, and keep a backup
for all ports. It is hard to track, I think.
Instead I choose to modify bonding to send igmp report for its master.
Changelog:
V2: correct comments
V3: move this check into bond_resend_igmp_join_requests()
V4: only send igmp reports if bond is enslaved to a bridge
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_alb_init_slave() is called from bond_enslave() and sets the slave's MAC
address. This is done differently for TLB and ALB modes.
bond->alb_info.rlb_enabled is used to discriminate between the two modes but
this flag may be uninitialized if the slave is being enslaved prior to calling
bond_open() -> bond_alb_initialize() on the master.
It turns out all the callers of alb_set_slave_mac_addr() pass
bond->alb_info.rlb_enabled as the hw parameter.
This patch cleans up the unnecessary parameter of alb_set_slave_mac_addr() and
makes the function decide based on the bonding mode instead, which fixes the
above problem.
Reported-by: Narendra K <Narendra_K@Dell.com>
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to lock soft irqs under bond_alb_xmit()
which already has softirq disabled.
Changes:
1. add non-bh/bh version to tlb_clear_slave()
2. represent BH and non BH hash table locks
_lock_rx_hashtbl_bh/_unlock_rx_hashtbl_bh
_lock_rx_hashtbl/_unlock_rx_hashtbl
_lock_tx_hashtbl_bh/_unlock_tx_hashtbl_bh
_lock_tx_hashtbl/_unlock_tx_hashtbl
Signed-off-by: Maxim Uvarov <maxim.uvarov@oracle.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.
The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves
The fix is to detach the slave (which removes it from the list)
in the unwind path.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.
The sysdev code will be going away soon, so this include needs to be
removed no matter what.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
This patch adds wrapper for ndo_vlan_rx_add_vid/ndo_vlan_rx_kill_vid
functions. Check for NETIF_F_HW_VLAN_FILTER feature is done in this
wrapper.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
