Commit Graph

19 Commits

Author SHA1 Message Date
Russell King
c8ebae3703 ARM: mmci: add dmaengine-based DMA support
Based on a patch from Linus Walleij.

Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface.  The changes over Linus' driver are:

- rename txsize_threshold to dmasize_threshold, as this reflects the
  purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer.  Some DMA controllers
  (eg, PL08x) are unable to be configured for scatter DMA and also listen
  to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
  They can do one or other but not both.  As MMCI uses LBREQ/LSREQ for the
  final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
  MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
  function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
  pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
  is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
  set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
  its own restrictions on buffer alignment, not the individual DMA engine
  users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
  causes LBREQ to be asserted for the last seven transfers, rather than
  six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
  transfer size required to complete the DMA operation.

Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04 13:25:49 +00:00
Russell King
51d4375dd7 ARM: mmci: no need for separate host->data_xfered
We don't need to store the number of bytes transferred in our host
structure - we can store this directly in data->bytes_xfered.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-02-04 13:25:48 +00:00
Linus Walleij
8cb2815574 ARM: 6632/3: mmci: stop using the blockend interrupts
Implement a suggestion from Russell to drop the use of blockend
interrupts altogether and instead rely on the data counter.

Tested with error-free cards on U300, U8500 and RealView PB1176.

Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-24 15:23:00 +00:00
Linus Walleij
f20f8f21e0 ARM: 6399/3: mmci: handle broken MCI_DATABLOCKEND hardware
On the U300 the MCI_DATAEND and MCI_DATABLOCKEND IRQs can arrive
out-of-order. Replace an ugly #ifdef hack with a proper runtime
solution which models what is really happening.

In the U300 DMA mode and on all Ux500 models, the MCI_DATABLOCKEND
flag isn't properly cleared in hardware following and ACK leading
to all kind of weird behaviour when the flag is still up in
subsequent interrupts, so we add two flags indicating the
error and handle this runtime.

Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-11-10 13:12:59 +00:00
Linus Walleij
2686b4b408 ARM: 6311/2: mmci: work with only one irq
The DBx500 variants have only one IRQ line hooked up.  Allow these (and
any other implementations which choose to use only one irq) to work by
directing the PIO interrupts also to the first IRQ line.

Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-11-10 13:10:01 +00:00
Linus Walleij
725343fa74 ARM: 6437/2: mmci: add some register defines for ST Micro variants
This adds a few registers to the MMCI/PL180 derivates that
is used for some odd control stuff like SDIO.

Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-10-11 22:54:34 +01:00
Rabin Vincent
148b8b39c1 ARM: 6308/1: mmci: support card detection interrupts
If an IRQ can be requested on the card detected GPIO, use it instead of
polling.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-09-23 15:01:59 +01:00
Rabin Vincent
8301bb68c6 ARM: 6310/1: mmci: support different FIFO sizes
The Ux500 variant has a 32-word FIFO (TXFIFOEMPTY is asserted when it
has 2 left) and TXFIFOHALFEMPTY is repurposed as TXFIFOBURSTWRITEABLE,
with a burst being defined as 8-words.  Likewise for RX.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-08-26 19:54:29 +01:00
Rabin Vincent
4380c14fd7 ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
Although both the U300 and Ux500 use ST variants, the HWFCEN bits are at
different positions, so use the variant_data to store the information.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-29 15:40:32 +01:00
Rabin Vincent
4956e10903 ARM: 6244/1: mmci: add variant data and default MCICLOCK support
Add a variant_data structure to handle the differences between the
various variants of this peripheral.  Add a first quirk for a default
MCICLOCK value, required on the Ux500 variant where the enable bit needs
to be always set, since it controls access to some registers.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-29 15:39:56 +01:00
Rabin Vincent
4ce1d6cbf0 ARM: 6237/1: mmci: use sg_miter API to fix multi-page sg handling
The mmci driver's SG list iteration logic assumes that each SG entry
spans only one page, and only maps and flushes one page of the sg.  This
is not a valid assumption.  Fix it by converting the driver to the
sg_miter API, which correctly handles sgs which span multiple pages.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-27 10:48:44 +01:00
Linus Walleij
771dc157e0 ARM: 6032/1: ARM: MMCI: support 8bit mode on the ST Micro version
This adds support for an 8bit wide bus to the card (data lines
MCIDAT0 through 7 exist) on the ST Micro version and alters the
U300 platform to support this. Also add some ST_ prefix to the
ST-specific registers.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-04-14 16:08:17 +01:00
Linus Walleij
34e84f39a2 ARM: 5721/1: MMCI enable the use of a regulator
This enables the use of a regulator to power the MMCI/PL180
PrimeCell. The OCR mask is calculated and voltage is set using
the new MMC core functions for discovering voltage ranges
in regulators. The platform translate_vdd function which basically
controls the 4 lines out of the PL180 is disabled if you use a
regulator instead.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-22 20:49:05 +01:00
Linus Walleij
6ef297f86b ARM: 5720/1: Move MMCI header to amba include dir
This moves the mmci platform data definition struct away from
arch/arm/include/asm/mach/mmc.h into the more proper place among
the other primecells in include/linux/amba/mmci.h and at the same
time renames it to "mmci.h", and also the struct in this file
confusingly named mmc_platform_data has been renamed
mmci_platform_data for clarity.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-09-22 20:49:04 +01:00
Russell King
8900144692 MMC: MMCI: use gpiolib for card detect/write protect
Use gpiolib where available (and when valid GPIOs are provided) for
write protect/card detect status reporting.  We fall back to the old
'status' method where gpiolib support is not available.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-07-09 15:16:07 +01:00
Linus Walleij
cc30d60e4c mmci: Add support for ST Micro derivate
This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.

Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2009-02-02 20:57:06 +01:00
Emil Medve
4e0177647a mmc: fix sg->page fallout
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-23 20:37:24 +02:00
Pierre Ossman
70f10482c6 mmc: update header file paths
Make sure all headers in the files reflect their true position
in the tree.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-26 01:53:31 +02:00
Pierre Ossman
1c6a0718f0 mmc: Move host and card drivers to subdirs
Clean up the drivers/mmc directory by moving card and host drivers
into subdirectories.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-01 13:04:17 +02:00