The new dma_attrs support must only be enabled for 64 bits as it's not
been implemented for 32 bits yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Push the sync below the secondary smp init hold loop and comment its purpose.
This should speed up boot by reducing global traffic during the single-threaded
portion of boot.
Signed-off-by: Sonny Rao <sonnyrao@us.ibm.com>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
VSX loads and stores will take an alignment exception when the address
is not on a 4 byte boundary.
This add support for these alignment exceptions and will emulate the
requested load or store.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
giveup_vsx didn't save the FPU and VMX regsiters. Change it to be
like giveup_fpr/altivec which save these registers.
Also update call sites where FPU and VMX are already saved to use the
original giveup_vsx (renamed to __giveup_vsx).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement save_stack_trace_tsk on powerpc, so that we can run with
latencytop.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It is okay for both _PAGE_GUARDED and _PAGE_COHERENT (G and M) to be set
in the same pte. In fact, even if that were not the case, there doesn't
seem to be any place where G is set without also setting I (_PAGE_NO_CACHE),
so the test for I is sufficient as a condition to clear _PAGE_COHERENT
when filling the hash table.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Background from Maynard Johnson:
As of POWER6, a set of 32 common events is defined that must be
supported on all future POWER processors. The main impetus for this
compat set is the need to support partition migration, especially from
processor P(n) to processor P(n+1), where performance software that's
running in the new partition may not be knowledgeable about processor
P(n+1). If a performance tool determines it does not support the
physical processor, but is told (via the
PPC_FEATURE_PSERIES_PERFMON_COMPAT bit) that the processor supports
the notion of the PMU compat set, then the performance tool can
surface just those events to the user of the tool.
PPC_FEATURE_PSERIES_PERFMON_COMPAT indicates that the PMU supports at
least this basic subset of events which is compatible across POWER
processor lines.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds a character driver for BSR support on IBM POWER systems including
Power5 and Power6. The BSR is an optional processor facility not currently
implemented by any other processors. It's primary purpose is fast large SMP
synchronization. More details on the BSR are in comments to the code which
follows. This patch adds BSR driver to pseries_defconfig.
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Today's linux-next build (powerpc allmodconfig) failed like this:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
But save_stack_trace is exported in arch/powerpc/kernel/stacktrace.c
I couldn't figure it out until I noticed these earlier warnings:
arch/powerpc/kernel/stacktrace.c:47: warning: data definition has no type or storage class
arch/powerpc/kernel/stacktrace.c:47: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/powerpc/kernel/stacktrace.c:47: warning: parameter names (without types) in function declaration
I applied the patch below.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linuxppc-dev@ozlabs.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the "uninitialized use" compile warning and avoid potential
runtime issue.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There isn't any reason at this point that we can't build 82xx, 83xx & 86xx
support in with the other 6xx based boards. Twiddle the Kconfigs to allow
this.
This allows us to remove the machine type selection for related to 6xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Publish the devices listed in dts under SOC as of_device for 85xx_cds
platform. The devices are needed by the 85xx EDAC driver.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For some reason long ago I decided that we should zero out the time base
when we calibrate the decrementer. The problem is that this can be
harmful in SMP systems where the firmware has already synchronized the
time bases on the various cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved the pic initialization into its own common file and out of the board
code. Also fixed the OF reference counting on the mpic node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These issues were reported by Stephen Rothwell for another 85xx board
port and pointed out by Chen Gong as issues in the DS port.
* mpic OF node reference counting was off
* of_device_id struct should be marked as __initdata
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
udbg_putc is a *function pointer* that is initialized during
udbg_init_cpm. It might not be initialized properly when called from
udbg_putc_cpm(), so (recursively) call udbg_putc_cpm() directly.
Signed-off-by: Nye Liu <nyet@mrv.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use
PCI sideband interrupt that is specified in the device tree.
Current HPCD's device tree specify that IDE interrupt is low to high
sensitive, but in practice ULi IDE throws active-high interrupts (not
active-low as all normal PCI devices).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix interrupt threading issue on pq2fads when running with CONFIG_PREEMPT_RT
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename MPIC label to mpic to match all other 85xx .dts and to fix compile
issue introduced by addition of the DMA node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a interrupt host for the interrupt controller in the mpc5121ads cpld.
PCI interrupts are 0-7 the rest are 8-15 Touchscreen pendown irq is
hardwired to irq1 All other irqs are chained to irq0
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move shared code from mpc5121_ads.c to new file mpc512x_shared.c
- mpc512x_find_ips_freq -> unchanged
- contents of mpc5121_ads_init_IRQ -> mpc512x_init_IRQ
- looking for fsl,mpc5121-ipic instead of fsl,ipic
- mpc5121_ads_declare_of_platform_devices -> mpc5121_declare_of_platform_devices
- and use compatible for lookup instead of node name
Add new generic board setup mpc5121_generic.c
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Plugs into the generic powerpc clock driver in
arch/powerpc/kernel/clock.c
The following subset of clk_interface is implemented:
clk_get, clk_put: get clock via name, release clock
clk_enable, clk_disable: enable or disable clock
clk_get_rate: get clock rate in Hz
clk_set_rate: stubbed
clk_round_rate: stubbed
clk_set_parent: NULL
clk_get_parent: NULL
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Current device tree is only bare bones. This patch adds nodes to make
it a complete tree for the MPC5121ads.
Added nodes include:
mbx - opengl coprocessor
nfc - nand flash controller
cpld-pic - on board cpld
rtc
clock - clock control
pmc - power management control
gpio
mscan - can module
i2c
axe - audio coprocessor
display - display interface unit
mdio
ethernet
usb
ioctl - pin config
pata
ac97 - PSC configured as AC97
pscfifo - psc fifo configuration
dma
pci
Fix typo in header changing MDS to ADS.
Add a compatible property of the form "fsl,mpc5121-..."
to nodes missing one.
Changed localbus compatible to fsl,mpc5121-localbus, this does
not break anything because the only code that uses it finds it
via the node name, not compatible.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix for the following compiler warnings:
CC arch/powerpc/sysdev/bestcomm/bestcomm.o
arch/powerpc/sysdev/bestcomm/bestcomm.c: In function 'mpc52xx_bcom_probe':
arch/powerpc/sysdev/bestcomm/bestcomm.c:446:
warning: format '%08lx' expects type 'long unsigned int',
but argument 2 has type 'phys_addr_t'
CC arch/powerpc/sysdev/bestcomm/sram.o
arch/powerpc/sysdev/bestcomm/sram.c: In function 'bcom_sram_init':
arch/powerpc/sysdev/bestcomm/sram.c:89:
warning: format '%08lx' expects type 'long unsigned int',
but argument 3 has type 'phys_addr_t'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Simplify the interface for setting up bestcomm DMA to PSCs by adding
some helper functions. The helper function sets the correct values
for the initator and ipr values in PSC DMA tasks based on the PSC
number.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the still missing FDT nodes for the MSCAN devices for
the TQM52xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert i2c-mpc to an of_platform driver. Utilize the code in
drivers/of-i2c.c to make i2c modules dynamically loadable by the
device tree.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On MPC5200 the PCI target control register (PCITCR) @ MBAR + 0xD6C is
initialized with only bit 7 (Latrule disable) set. The 8-Bit write
combine timer (Bits 24..31) should be also set to a reasonable value
_greater zero_ (0x08 = default) since setting it to 0x00 leads to
_very poor_ performance as a PCI target since external burst won't be
possible at all.
Setting the WCT to 0x08 (cache-line size) leads to good overall perfomance.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch enables 32bit PPC's (with 36bit physical address space, e.g.
IBM/AMCC PPC44x) to run with >= 4GB of RAM. Mostly its just replacing types
(unsigned long -> phys_addr_t).
Tested on an AMCC Katmai with 4GB of DDR2.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Allow the Rev A Warp boards to boot from NAND.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is some preliminary work to improve TLB management on SW loaded
TLB powerpc platforms. This introduce support for non-atomic PTE
operations in pgtable-ppc32.h and removes write back to the PTE from
the TLB miss handlers. In addition, the DSI interrupt code no longer
tries to fixup write permission, this is left to generic code, and
_PAGE_HWWRITE is gone.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
It is inconvenient to add additional default targets to the bootwrapper
Makefile for each new board supported which just needs a different dts
file. This change allows the defconfig to specify additional build
targets.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The following patch restores the PERR and SERR bits in the PCI
command register during an EEH device recovery. We have found
at least one case (an Agilent test card) where the PERR/SERR
bits are set to 1 by firmware at boot time, but are not restored
to 1 during EEH recovery. The patch fixes the Agilent card
problem. It has been tested on several other EEH-enabled cards
with no regressions.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
regs is not used in emulate_fp_pair so remove it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the ucontext changed to add the VSX context, this broke backwards
compatibly on swapcontext. swapcontext only compares the ucontext size
passed in from the user to the new kernel ucontext size.
This adds a check against the old ucontext size (with VMX but without
VSX). It also adds some sanity check for ucontexts without VSX, but
where VSX is used according the MSR. Fixes for both 32 and 64bit
processes on 64bit kernels
Kudos to Paulus for noticing.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Choose a more meaningful name for better System.map readability and
autopsy value etc.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Various instances of the EMAC core have varying: 1) number of address
match slots, 2) width of the registers for handling address match slots,
3) number of registers for handling address match slots and 4) base
offset for those registers.
As the driver stands today, it assumes that all EMACs have 4 IAHT and
GAHT 32-bit registers, starting at offset 0x30 from the register base,
with only 16-bits of each used for a total of 64 match slots.
The 405EX(r) and 460EX now use the EMAC4SYNC core rather than the EMAC4
core. This core has 8 IAHT and GAHT registers, starting at offset 0x80
from the register base, with ALL 32-bits of each used for a total of
256 match slots.
This adds a new compatible device tree entry "emac4sync" and a new,
related feature flag "EMAC_FTR_EMAC4SYNC" along with a series of macros
and inlines which supply the appropriate parameterized value based on
the presence or absence of the EMAC4SYNC feature.
The code has further been reworked where appropriate to use those macros
and inlines.
In addition, the register size passed to ioremap is now taken from the
device tree:
c4 for EMAC4SYNC cores
74 for EMAC4 cores
70 for EMAC cores
rather than sizeof (emac_regs).
Finally, the device trees have been updated with the appropriate compatible
entries and resource sizes.
This has been tested on an AMCC Haleakala board such that: 1) inbound
ICMP requests to 'haleakala.local' via MDNS from both Mac OS X 10.4.11
and Ubuntu 8.04 systems as well as 2) outbound ICMP requests from
'haleakala.local' to those same systems in the '.local' domain via MDNS
now work.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current low level hash code on LPAR configurations clears
_PAGE_COHERENT (M) when either _PAGE_GUARDED (G) or _PAGE_NO_CACHE (I)
is set. This conflicts with _PAGE_SAO which has M, I and W bits sets at
once (normally invalid combo) to indicate the new SAO attribute.
This changes the code to allow that case.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Allow an application to enable Strong Access Ordering on specific pages of
memory on Power 7 hardware. Currently, power has a weaker memory model than
x86. Implementing a stronger memory model allows an emulator to more
efficiently translate x86 code into power code, resulting in faster code
execution.
On Power 7 hardware, storing 0b1110 in the WIMG bits of the hpte enables
strong access ordering mode for the memory page. This patchset allows a
user to specify which pages are thus enabled by passing a new protection
bit through mmap() and mprotect(). I have defined PROT_SAO to be 0x10.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes the oops and backtrace code to use the new %pS
printk extension to print out symbols rather than manually
calling print_symbol.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move device_to_mask() to dma-mapping.h because we need to use it from
outside dma_64.c in a later patch.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make cell_dma_dev_setup_iommu() return a pointer to the struct iommu_table
(or NULL if no table can be found) rather than putting this pointer into
dev->archdata.dma_data (let the caller do that), and rename this function
to cell_get_iommu_table() to reflect this change.
This will allow us to get the iommu table for a device that doesn't have
the table in the archdata.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update powerpc to use the new dma_*map*_attrs() interfaces. In doing so
update struct dma_mapping_ops to accept a struct dma_attrs and propagate
these changes through to all users of the code (generic IOMMU and the
64bit DMA code, and the iseries and ps3 platform code).
The old dma_*map_*() interfaces are reimplemented as calls to the
corresponding new interfaces.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make iommu_map_sg take a struct iommu_table. It did so before commit
740c3ce667 (iommu sg merging: ppc: make
iommu respect the segment size limits).
This stops the function looking in the archdata.dma_data for the iommu
table because in the future it will be called with a device that has
no table there.
This also has the nice side effect of making iommu_map_sg() match the
other map functions.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As nr_active counter includes also spus waiting for syscalls to return
we need a seperate counter that only counts spus that are currently running
on spu side. This counter shall be used by a cpufreq governor that targets
a frequency dependent from the number of running spus.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reduce the output verbosity of ps3_system_bus_match().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is dma_mask in of_device upon of_platform_device_create()
but we don't actually set coherent_dma_mask. This may cause weird
behavior of USB subsystem using of_device USB host drivers.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the .ctx debug file in spu context directories is always
present.
We'd prefer to prevent users from relying on this file, so add a
"debug" mount option to spufs. The .ctx file will only be added to
the context directories when this option is present.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Populate the size member of a few context files. Leave out files that
have different semantics with read vs mmap, or contain a
variable-length hex string.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, spufs never specifies the i_size for the files in context
directories, so stat() always reports 0-byte files.
This change adds allows the spufs_dir_(nosched_)contents arrays to
specify a file size. This allows stat() to report correct file sizes,
and makes SEEK_END work.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
An spu context shouldn't get an extra tick if the time slice code
couldn't find something else to run. This means contexts that are not
within spu_run (ie, SPU_SCHED_SPU_RUN is cleared) will not receive
extra ticks while we have no other contexts waiting.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Add a ctxt file to spufs that shows spu context information that is used
in scheduling. This info can be used for debugging spufs scheduler
issues, and to isolate between application and spufs problems as it
shows a lot of state such as priorities and dispatch counts.
This file contains internal spufs state and is subject to change at any
time, and therefore no applications should depend on it. The file is
intended for the use of spufs kernel developers.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
A recent patch to legacy_serial.c factored out some code by
using the of_match_node() facility to match a node against
an array of possible matches. However, the patch didn't properly
terminate the array causing potential crashes in cases where no
match is found. In addition, the name of the array was poorly
chosen for a static symbol making debugging harder.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wrapper script is missing the bits needed for building generic
simpleImage targets (targets which don't depend on any particular
firmware interface and retrieve all their data from the device tree).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There have been many questions on and off the mailing list about how
exactly the bootwrapper is used for embedded targets. Add some
documentation and help text to try and clarify the system.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This defconfig file is specific to Xilinx Virtex 5 FXT platform.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Updates the cputable to include the 440 processor found in the
Xilinx Virtex5 FXT FPGA.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Support for the Xilinx Virtex5 FXT 440 is being added.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The following changes add processing to initialize the Xilinx 16550 UART
in the boot wrapper for Virtex targets without firmware. Normally the
boot wrapper assumes that the serial port has already been initialized by
firmware.
The wrapper was also modified to add the 440 build.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This new file adds support for the ML507 reference design. The ML507
uses the Virtex 5 FXT FPGA which embeds a ppc440 core.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Today's linux-next build (powerpc ppc64_defconfig) failed like this:
arch/powerpc/mm/tlb_64.c: In function 'pgtable_free_now':
arch/powerpc/mm/tlb_64.c:66: error: too many arguments to function 'smp_call_function'
arch/powerpc/kernel/machine_kexec_64.c: In function 'kexec_prepare_cpus':
arch/powerpc/kernel/machine_kexec_64.c:175: error: too many arguments to function 'smp_call_function'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: <linuxppc-dev@ozlabs.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update the association of a memory section with a numa node that
occurs during hotplug add of a memory section. This adds a check in
the hot_add_scn_to_nid() routine for the
ibm,dynamic-reconfiguration-memory node in the device tree. If
present the new hot_add_drconf_scn_to_nid() routine is invoked, which
can properly parse the ibm,dynamic-reconfiguration-memory node of the
device tree and make the proper numa node associations.
This also introduces the valid_hot_add_scn() routine as a helper
function for code that is common to the hot_add_scn_to_nid() and
hot_add_drconf_scn_to_nid() routines.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits off several pieces of code that parse the
ibm,dynamic-reconfiguration-memory node of the device tree into separate
helper routines. This is in preparation for the next commit that will
use these helper routines. There are no functional changes in this patch.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the device tree manipulation routines so that memory
add/remove of lmbs represented under the
ibm,dynamic-reconfiguration-memory node of the device tree invokes the
hotplug notifier chain.
This change is needed because of the change in the way memory is
represented under the ibm,dynamic-reconfiguration-memory node. All lmbs
are described in the ibm,dynamic-memory property instead of having a
separate node for each lmb as in previous device tree layouts. This
requires the update_node() routine to check for updates to the
ibm,dynamic-memory property and invoke the hotplug notifier chain.
This also updates the pseries hotplug notifier to be able to gather information
for lmbs represented under the ibm,dynamic-reconfiguration-memory node and
have the lmbs added/removed.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the base address of the lmb to derive the starting page frame number
instead of trying to extract it from the drc index of the lmb. The drc
index should not be used for this as it will, and did, break.
Until this point, systems that have had memory represented in the device
tree with a node for each lmb the drc index would (luckily) closely
track the base address of the lmb. For example a lmb with a drc index
of 8000000a would have a base address of a0000000. This correlation
allowed the current code to derive the starting page frame number from
the drc inddex
Device tree layouts where lmbs are represented under the
ibm,dynamic-reconfiguration-memory node in the ibm,dynamic-memory
property do not have this correlation between the drc index and base
address of the lmb.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow the phandle passed to the /proc/ppc64/ofdt file to be specified
in formats other than decimal. This allows us to easily specify phandle
values in hex that would otherwise appear as negative integers.
This is an issue on systems where the value of
/proc/device-tree/ibm,dynamic-reconfiguration-memory.ibm,phandle is
fffffff9. Having to pass this to the ofdt file as a string results in
a large negative number, and simple_strtoul() does not handle negative
numbers.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since Roland's ptrace cleanup starting with commit
f65255e8d5 ("[POWERPC] Use user_regset
accessors for FP regs"), the dump_task_* functions are no longer being
used.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges and cleans up some of the ugly copy/to from user code
which is required for the new fpr and vsx layout in the thread_struct.
Also fixes some hard coded buffer sizes and removes a redundant
fpr_flush_to_thread.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To allow for a single kernel image on e500 v1/v2/mc we need to fixup lwsync
at runtime. On e500v1/v2 lwsync causes an illop so we need to patch up
the code. We default to 'sync' since that is always safe and if the cpu
is capable we will replace 'sync' with 'lwsync'.
We introduce CPU_FTR_LWSYNC as a way to determine at runtime if this is
needed. This flag could be moved elsewhere since we dont really use it
for the normal CPU_FTR purpose.
Finally we only store the relative offset in the fixup section to keep it
as small as possible rather than using a full fixup_entry.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to use PPC_LCMPI otherwise we get compile errors like:
arch/powerpc/lib/feature-fixups-test.S: Assembler messages:
arch/powerpc/lib/feature-fixups-test.S:142: Error: Unrecognized opcode: `cmpdi'
arch/powerpc/lib/feature-fixups-test.S:149: Error: Unrecognized opcode: `cmpdi'
arch/powerpc/lib/feature-fixups-test.S:164: Error: Unrecognized opcode: `cmpdi'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the kernel fails to build with the above config options with:
CC arch/powerpc/mm/mem.o
arch/powerpc/mm/mem.c: In function 'arch_add_memory':
arch/powerpc/mm/mem.c:130: error: implicit declaration of function 'create_section_mapping'
This explicitly includes asm/sparsemem.h in arch/powerpc/mm/mem.c and
moves the guards in include/asm-powerpc/sparsemem.h to protect the
SPARSEMEM specific portions only.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Suspend/resume ("echo mem > /sys/power/state") does not work with
vanilla kernels -- the system does not suspend correctly and just
hangs. This patch fixes this so suspend/resume works:
1) of_iomap does not map the whole 0xC000 of the MPC5200 immr so
saving registers does not work.
2) PCI registers need to be saved and restored.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The legacy serial driver does not work with an 8250 type UART that is
described in the device tree with the reg-offset and reg-shift
properties. This change makes legacy_serial ignore these devices.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This change to the makefile corrects the build of a simpleImage with initrd.
Signed-off-by: John Linn <john.linn@xilinx>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This correctly hooks the VSX dump into Roland McGrath core file
infrastructure. It adds the VSX dump information as an additional elf
note in the core file (after talking more to the tool chain/gdb guys).
This also ensures the formats are consistent between signals, ptrace
and core files.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix compile error when CONFIG_VSX is enabled.
arch/powerpc/kernel/signal_64.c: In function 'restore_sigcontext':
arch/powerpc/kernel/signal_64.c:241: error: 'i' undeclared (first use in this function)
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Gcc 4.3 produced this warning:
arch/powerpc/kernel/signal_64.c: In function 'restore_sigcontext':
arch/powerpc/kernel/signal_64.c:161: warning: array subscript is above array bounds
This is caused by us copying to aliases of elements of the pt_regs
structure. Make those explicit.
This adds one extra __get_user and unrolls a loop.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes the experimental status of kdump on PPC64. kdump is on
PPC64 now since more than one year and it has proven to be stable.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On PowerPC processors with non-coherent cache architectures the DMA
subsystem calls invalidate_dcache_range() before performing a DMA read
operation. If the address and length of the DMA buffer are not aligned
to a cache-line boundary this can result in memory outside of the DMA
buffer being invalidated in the cache. If this memory has an
uncommitted store then the data will be lost and a subsequent read of
that address will result in an old value being returned from main memory.
Only when the DMA buffer starts on a cache-line boundary and is an exact
mutiple of the cache-line size can invalidate_dcache_range() be called,
otherwise flush_dcache_range() must be called. flush_dcache_range()
will first flush uncommitted writes, and then invalidate the cache.
Signed-off-by: Andrew Lewis <andrew-lewis at netspace.net.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since most bootloaders or wrappers tend to update or add some information
to the .dtb they a handled they need some working space to do that in.
By default add 1K of padding via a default setting of DTS_FLAGS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add CONFIG_VSX config build option. Must compile with POWER4, FPU and ALTIVEC.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch extends the floating point save and restore code to use the
VSX load/stores when VSX is available. This will make FP context
save/restore marginally slower on FP only code, when VSX is available,
as it has to load/store 128bits rather than just 64bits.
Mixing FP, VMX and VSX code will get constant architected state.
The signals interface is extended to enable access to VSR 0-31
doubleword 1 after discussions with tool chain maintainers. Backward
compatibility is maintained.
The ptrace interface is also extended to allow access to VSR 0-31 full
registers.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the macros for the VSX load/store instruction as most
binutils are not going to support this for a while.
Also add VSX register save/restore macros and vsr[0-63] register definitions.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a VSX CPU feature. Also add code to detect if VSX is available
from the device tree.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
