The Microblaze dynamic ftrace code assumes a call ordering that is not met
in all scenarios. Specifically, executing a command similar to:
echo 105 > /sys/kernel/debug/tracing/set_ftrace_pid
before any other tracing-related commands results in a kernel panic:
BUG: failure at arch/microblaze/kernel/ftrace.c:198/ftrace_update_ftrace_func()!
Recoding ftrace_update_ftrace_func() to use &ftrace_caller directly eliminates
the need to capture its address elsewhere (and thus rely on a particular call
sequence).
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
When ide taskfile access is being used (for example with hdparm --security
commands) and cfq scheduler is selected, the scheduler crashes on BUG in
cfq_put_request.
The reason is that the cfq scheduler is tracking counts of read and write
requests separately; the ide-taskfile subsystem allocates a read request and
then flips the flag to make it a write request. The counters in cfq will
mismatch.
This patch changes ide-taskfile to allocate the READ or WRITE request as
required and don't change the flag later.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NODEMASK_ALLOC/FREE are mapped to kmalloc/free if NODES_SHIFT > 8.
Among its several users, drivers/base/node.c wasn't including slab.h
leading to build failure if NODES_SHIFT > 8. Include slab.h from
drivers/base/node.c.
This isn't an ideal solution but including slab.h directly from
nodemask.h is not an option because nodemask.h gets included
everywhere. For now, make it work by including slab.h from its users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ingo Molnar <mingo@elte.hu>
There is a problem with the ACPI video resume routine that it's
executed before the GPU that may be accessed by it. To fix this
issue, move the ACPI video resume to a power management notifier,
so that's executed after resuming all devices, including the GPU.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15096, which is
a listed regression from 2.6.31.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Force MSI irq handlers to run with interrupts disabled
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] hpwdt - fix lower timeout limit
[WATCHDOG] iTCO_wdt: TCO Watchdog patch for additional Intel Cougar Point DeviceIDs
[WATCHDOG] doc: Fix use of WDIOC_SETOPTIONS ioctl.
[WATCHDOG] doc: watchdog simple example: don't fail on fsync()
[WATCHDOG] set max63xx driver as ARM only
[WATCHDOG] powerpc: pika_wdt ident cannot be const
The original code doesn't take into consideration that the value of
MIXART_BA0_SIZE - pos can be less than zero which would lead to a large
unsigned value for "count".
Also I moved the check that read size is a multiple of 4 bytes below
the code that adjusts "count".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to Intel Software Devel Manual Volume 3B, the
Nehalem-EX PMU is just like regular Nehalem (except for the
uncore support, which is completely different).
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
LKML-Reference: <alpine.DEB.2.00.1004060956580.1417@cl320.eecs.utk.edu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 5a0e3ad ("include cleanup: Update gfp.h and slab.h
includes to prepare for breaking implicit slab.h inclusion
from percpu.h") added a '#include <linux/slab.h>' to
tools/perf/builtin-kmem.h because: that tool has lines like
this:
if (!strcmp(event->name, "kmalloc") ||
!strcmp(event->name, "kmem_cache_alloc")) {
process_alloc_event(data, event, cpu, timestamp, thread, 0);
return;
}
So, using the script regex:
>>> import re
>>> s = re.compile(r'^(|.*[^a-zA-Z0-9_])_*(slab_is_available|kmem_cache_|k[mzc]alloc|krealloc|kz?free|ksize|__getname|putname)')
>>> l = ' !strcmp(event->name, "kmem_cache_alloc")) {'
>>> s.search(l)
<_sre.SRE_Match object at 0xb77b1ad0>
>>>
Remove that file that is not available in the tools/perf include
path and thus builtin-kmem.c couldn't be compiled.
Reported-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1270561053-14308-1-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
copy_to_user() returns the number of bytes left to be copied.
This was a typo from: d82ef020cf "proc: pagemap: Hold mmap_sem during
page walk".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some BIOSes don't configure HPA during boot but do so while resuming.
This causes harddrives to shrink during resume making libata detach
and reattach them. This can be worked around by unlocking HPA if old
size equals native size.
Add ATA_DFLAG_UNLOCK_HPA so that HPA unlocking can be controlled
per-device and update ata_dev_revalidate() such that it sets
ATA_DFLAG_UNLOCK_HPA and fails with -EIO when the above condition is
detected.
This patch fixes the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15396
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Oleksandr Yermolenko <yaa.bta@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Crucial said,
Thank you for contacting us. We know that with our M225 line of SSDs
you sometimes need to disable NCQ (native command queuing) to avoid
just the type of errors you're seeing. Our recommendation for the
M225 is to add libata.force=noncq to your Linux kernel boot options,
under the kernel ATA library option.
I have sent your feedback to the engineers working on the C300, and
asked them to please pass it on to the firmware team. I have been
notified that they are in the process of testing and finalizing a
new firmware version, that you can expect to see released around the
end of April. We’ll keep you posted as to when it will be available
for download.
So, turn off NCQ on the drive w/ the current firmware revision.
Reported in the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15573
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: lethalwp@scarlet.be
Reported-by: Luke Macken <lmacken@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On configurations where IRQ line is shared with a different
controller, spurious IRQs may happen continuously. The message was
put there primarily for debugging anyway. Kill it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[Novell Bug 581103] HP Watchdog driver has arbitrary (wrong) timeout limits.
Fix the lower timeout limit to a more appropriate value.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@kernel.org>
In the watchdog-test program and watchdog-api.txt, pass the values to
the WDIOC_SETOPTIONS ioctl as a pointer to an integer containing the
values intead of directly in the third ioctl argument. The actual
watchdog drivers in drivers/watchdog don't read the options directly
from the argument but use get_user and copy_from_user.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
taskset on 2.6.34-rc3 fails on one of my ppc64 test boxes with
the following error:
sched_getaffinity(0, 16, 0x10029650030) = -1 EINVAL (Invalid argument)
This box has 128 threads and 16 bytes is enough to cover it.
Commit cd3d8031eb (sched:
sched_getaffinity(): Allow less than NR_CPUS length) is
comparing this 16 bytes agains nr_cpu_ids.
Fix it by comparing nr_cpu_ids to the number of bits in the
cpumask we pass in.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Sharyathi Nagesh <sharyath@in.ibm.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Mike Travis <travis@sgi.com>
LKML-Reference: <20100406070218.GM5594@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Module refcounting is implemented with a per-cpu counter for speed.
However there is a race when tallying the counter where a reference may
be taken by one CPU and released by another. Reference count summation
may then see the decrement without having seen the previous increment,
leading to lower than expected count. A module which never has its
actual reference drop below 1 may return a reference count of 0 due to
this race.
Module removal generally runs under stop_machine, which prevents this
race causing bugs due to removal of in-use modules. However there are
other real bugs in module.c code and driver code (module_refcount is
exported) where the callers do not run under stop_machine.
Fix this by maintaining running per-cpu counters for the number of
module refcount increments and the number of refcount decrements. The
increments are tallied after the decrements, so any decrement seen will
always have its corresponding increment counted. The final refcount is
the difference of the total increments and decrements, preventing a
low-refcount from being returned.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla1280: retain firmware for error recovery
[SCSI] attirbute_container: Initialize sysfs attributes with sysfs_attr_init
[SCSI] advansys: fix regression with request_firmware change
[SCSI] qla2xxx: Updated version number to 8.03.02-k2.
[SCSI] qla2xxx: Prevent sending mbx commands from sysfs during isp reset.
[SCSI] qla2xxx: Disable MSI on qla24xx chips other than QLA2432.
[SCSI] qla2xxx: Check to make sure multique and CPU affinity support is not enabled at the same time.
[SCSI] qla2xxx: Correct vp_idx checking during PORT_UPDATE processing.
[SCSI] qla2xxx: Honour "Extended BB credits" bit for CNAs.
[SCSI] scsi_transport_fc: Make sure commands are completed when rport is offline
[SCSI] libiscsi: Fix recovery slowdown regression
IRQ 29 has two possible interrupts DDRINT and RTC, but having both in
the default priority table is confusing (and triggers a warning from
sparse.)
This patch removes the lower priority DDRINT from the default priority
table leaving the RTC setting as the default.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes an issue where a DMA channel can erroneously process an
event generated by a previous transfer. A failure case is where DMA is
being used for SPI transmit and receive channels on OMAP L138. In this
case there is a single bit that controls all event generation from the
SPI peripheral. Therefore it is possible that between when edma_stop()
has been called for the transmit channel on a previous transfer and
edma_start() is called for the transmit channel on a subsequent transfer,
that a transmit event has been generated.
The fix is to clear events in edma_start(). This prevents false events
from being processed when events are enabled for that channel.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The da8xx/omap-l1 boards refuse to build when CONFIG_DAVINCI_MUX is undefined
because arch/arm/mach-davinci/mux.c:da8xx_pinmux_setup() is not defined.
This patch fixes this issue. This is build tested with davinci_all_defconfig
and da8xx_omapl_defconfig and boot tested on DA830 EVM.
Reported-by: Shanmuga Sundaram Mahendran <shanmuga@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On da830, when the same timer is used for clocksource and clockevent,
the timer can be started before the clockevent is
registered/initialzed. This creates a window where a timer
interrupt might fire before the clockevent handler has been
setup and causes a crash.
This patch moves the actual enable/start of the timer after
the clockevent has ben registered.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The commit 6a4f2ccb46 introduced a wrong
comparision for the array range check, which effectively skips the whole
initialization of DAC connections. Fixed now.
Reference: bko#15689
https://bugzilla.kernel.org/show_bug.cgi?id=15689
Reported-by: Adrian Ulrich <kernel@blinkenlights.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: saving negative to unsigned char
9p: return on mutex_lock_interruptible()
9p: Creating files with names too long should fail with ENAMETOOLONG.
9p: Make sure we are able to clunk the cached fid on umount
9p: drop nlink remove
fs/9p: Clunk the fid resulting from partial walk of the name
9p: documentation update
9p: Fix setting of protocol flags in v9fs_session_info structure.
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: add check for changed leaves in setup_leaf_for_split
Btrfs: create snapshot references in same commit as snapshot
Btrfs: fix small race with delalloc flushing waitqueue's
Btrfs: use add_to_page_cache_lru, use __page_cache_alloc
Btrfs: fix chunk allocate size calculation
Btrfs: kill max_extent mount option
Btrfs: fail to mount if we have problems reading the block groups
Btrfs: check btrfs_get_extent return for IS_ERR()
Btrfs: handle kmalloc() failure in inode lookup ioctl
Btrfs: dereferencing freed memory
Btrfs: Simplify num_stripes's calculation logical for __btrfs_alloc_chunk()
Btrfs: Add error handle for btrfs_search_slot() in btrfs_read_chunk_tree()
Btrfs: Remove unnecessary finish_wait() in wait_current_trans()
Btrfs: add NULL check for do_walk_down()
Btrfs: remove duplicate include in ioctl.c
Fix trivial conflict in fs/btrfs/compression.c due to slab.h include
cleanups.
There have been a number of reports of people seeing the message:
"name_count maxed, losing inode data: dev=00:05, inode=3185"
in dmesg. These usually lead to people reporting problems to the filesystem
group who are in turn clueless what they mean.
Eventually someone finds me and I explain what is going on and that
these come from the audit system. The basics of the problem is that the
audit subsystem never expects a single syscall to 'interact' (for some
wish washy meaning of interact) with more than 20 inodes. But in fact
some operations like loading kernel modules can cause changes to lots of
inodes in debugfs.
There are a couple real fixes being bandied about including removing the
fixed compile time limit of 20 or not auditing changes in debugfs (or
both) but neither are small and obvious so I am not sending them for
immediate inclusion (I hope Al forwards a real solution next devel
window).
In the meantime this patch simply adds 'audit' to the beginning of the
crap message so if a user sees it, they come blame me first and we can
talk about what it means and make sure we understand all of the reasons
it can happen and make sure this gets solved correctly in the long run.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saving -EINVAL as unsigned char truncates the high bits and changes it
into 234 instead of -22. This breaks the test for "if (ret == -EINVAL)"
in parse_opts().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
If "err" is -EINTR here the original code calls mutex_unlock() and then
returns, but it should just return directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
------------------------------------------------------------------------------
Download Intel® Parallel Studio Eval
Try the new software tools for yourself. Speed compiling, find bugs
proactively, and fine-tune applications for parallel performance.
See why Intel Parallel Studio got high marks during beta.
http://p.sf.net/sfu/intel-sw-dev
setup_leaf_for_split needs to drop the path and search again, and has
checks to see if the item we want to split changed size. But, it misses
the case where the leaf changed and now has enough room for the item
we want to insert.
This adds an extra check to make sure the leaf really needs splitting
before we call btrfs_split_leaf(), which keeps us from trying to split
a leaf with a single item.
btrfs_split_leaf() will blindly split the single item leaf, leaving us
with one good leaf and one empty leaf and then a crash.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This creates the reference to a new snapshot in the same commit as the
snapshot itself. This avoids the need for a second commit in order for a
snapshot to be persistent, and also avoids the problem of "leaking" a
new snapshot tree root if the host crashes before the second commit takes
place.
It is not at all clear to me why it wasn't always done this way. If there
is still a reason for the two-stage {create,finish}_pending_snapshots()
approach I'm missing something! :)
I've been running this for a couple weeks under pretty heavy usage (a few
snapshots per minute) without obvious problems.
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Everytime we start a new flushing thread, we init the waitqueue if there isn't a
flushing thread running. The problem with this is we check
space_info->flushing, which we clear right before doing a wake_up on the
flushing waitqueue, which causes problems if we init the waitqueue in the middle
of clearing the flushing flagh and calling wake_up. This is hard to hit, but
the code is wrong anyway, so init the flushing/allocating waitqueue when
creating the space info and let it be. I haven't seen the panic since I've been
using this patch. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Pagecache pages should be allocated with __page_cache_alloc, so they
obey pagecache memory policies.
add_to_page_cache_lru is exported, so it should be used. Benefits over
using a private pagevec: neater code, 128 bytes fewer stack used, percpu
lru ordering is preserved, and finally don't need to flush pagevec
before returning so batching may be shared with other LRU insertions.
Signed-off-by: Nick Piggin <npiggin@suse.de>:
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
[Note that this is a backported version for 2.6.34.
Upstream commit is fd23b7dee]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'slabh' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc:
eeepc-wmi: include slab.h
staging/otus: include slab.h from usbdrv.h
percpu: don't implicitly include slab.h from percpu.h
kmemcheck: Fix build errors due to missing slab.h
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
iwlwifi: don't include iwl-dev.h from iwl-devtrace.h
x86: don't include slab.h from arch/x86/include/asm/pgtable_32.h
Fix up trivial conflicts in include/linux/percpu.h due to
is_kernel_percpu_address() having been introduced since the slab.h
cleanup with the percpu_up.c splitup.
After more tests it appears that EAPD needs to be enabled
on both the 0x14 and 0x15 NIDs to enable the main speaker
and headphone amplifiers. The maximum volume setting is
now equal to what the machine achieves under other operating
systems.
Disabling Front or LFE playback triggers EAPD and disables
the amplifier. As such, these two playback switches have
been removed from the mixer.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
module: add stub for is_module_percpu_address
percpu, module: implement and use is_kernel/module_percpu_address()
module: encapsulate percpu handling better and record percpu_size
Fix a memory leak in anon_vma_fork(), where we fail to tear down the
anon_vmas attached to the new VMA in case setting up the new anon_vma
fails.
This bug also has the potential to leave behind anon_vma_chain structs
with pointers to invalid memory.
Reported-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dcache prune happen on umount. So we cannot mark the client
satus disconnect. That will prevent a 9p call to the server
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
We need to drop the link count on the inode of a sucessfull remove
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
