Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.
But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).
Remove the not needed anymore dependency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add IO memory and IRQ ressources for pxa based SoC to be
able to use the new rtc-pxa driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Following the removal of the "->policy" usage for PXA255 in patch
459fc208ab (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.
It also cures the runtime warning that was printed each time the
frequency was changed.
Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.
Tested on an Arcom/Eurotech Viper.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Let's put these devices into a central place even if they are now
processor specific, as they might be re-used in later processors.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
We now have generic PWM API for PXA, the PWM registers definitions are
now used nowhere, and it is not encouraged to manipulate them directly
by driver code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h.
Declaration of pxa_gpio_mode() is still being referenced and thus moved into
pxa2xx-gpio.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Original patch from Marek Vasut, the problems with PXA26x are:
1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
inverted in GPDR2, as well as their alternate function bits being
'1' for their GPIO functionality in GAFRx
2. there is no easy way to decide if the processor is a pxa26x or a
pxa250/pxa255 at run-time, so the assumption here is the pxa26x
will be treated as one of the pxa25x variants, and board code
should have a better knowledge of the processor it is featured
Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.
Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.
__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit da1a3dc0eb.
The originally proposed way in the above commit is incorrect. And
there is no easy way to distinguish between pxa25x and pxa26x at
run-time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we
already have that variable, remove the unnecessary 'gpio_nr' now.
Also, fix the incorrect GPIO number passed in pxa27x_init_irq().
Note: pxa_last_gpio should be initialized earlier, and this is true
since it's been assigned in machine_desc->init_irq().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA SoC have several GPIOs muxed on only one wakeup source.
Add support for these wakeup sources which were missing
in mfp core support.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch makes do_hw_reset the default reboot behavior when nothing
else matches. This restores reboot functionality on gumstix basix
devices where reboot=cold is the default boot argument.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original incorrect configuration caused GPIO79_nCS_3 being overriden,
thus resulted in the NAND flash not being detected. The real PSKTSEL pin
is on GPIO104 instead of GPIO79.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
corgi_lcd has symbol conflict with corgi_bl driver.
Fix it by renaming common symbol in new corgi_lcd driver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
Separate building of corgi_ssp.c, and introduce a new hidden config option
CONFIG_CORGI_SSP_DEPRECATED for this. Aslo mark corgi_ts.c and corgi_bl.c
as deprecated.
This unbreaks the legacy configs in {corgi,spitz}_defconfig, however, SPI
based ADS7846 touchscreen driver and a new SPI-based corgi_lcd.c driver
with integrated backlight support are recommended.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit 68677ab3d0.
A smoother migration path would be making corgi_ts.c and other drivers
depending on corgi_ssp.c and corgi_lcd.c to depend on BROKEN instead,
and still allows those to exist around for some time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On Sharp SL-6000 lcd/backlight is a bit complex, so add two drivers
one for lcd-driving chip, other one for dac regulating the backlight
LEDS.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-next' of git://git.o-hand.com/linux-mfd:
mfd: further unbork the ucb1400 ac97_bus dependencies
mfd: ucb1400 needs GPIO
mfd: ucb1400 sound driver uses/depends on AC97_BUS:
mfd: Don't use NO_IRQ in WM8350
mfd: update TMIO drivers to use the clock API
mfd: twl4030-core irq simplification
mfd: add base support for Dialog DA9030/DA9034 PMICs
mfd: TWL4030 core driver
mfd: support tmiofb cell on tc6393xb
mfd: add OHCI cell to tc6393xb
mfd: Fix htc-egpio compile warning
mfd: do tcb6393xb state restore on resume only if requested
mfd: provide and use setup hook for tc6393xb
mfd: update sm501 debugging/low information messages
mfd: reduce stack usage in mfd-core.c
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
As requested by Ian make state restore only if it's requested
by platform data: some platforms do correctly save the state of
the chip during suspend/resume, but some (like tosa) incorrectly
power off the chip at suspend, so the driver supports restoring
some bits of the tc6393xb state (not full, merely enough to support
resume on tosa). With this patch this code is disabled by default.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Instead of using bitfields for initial gpio setup,
provide generic setup/teardown hooks that can be used
to set the gpio states, register child devices, etc.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
