Added Tx routine for ULD
- define interface for ULD Tx.
Export routines used for Tx data
- Routines common for data transmit are used by cxgb4 and chcr
drivers.
- EXPORT routines enable transmit from chcr driver.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
In the function ipvlan_get_L3_hdr, current codes use pskb_may_pull to
make sure the skb header has enough linear room for ipv6 header. But it
would use the latter memory directly without linear check when it is icmp.
So it still may access the unepxected memory in ipvlan_addr_lookup.
Now invoke the pskb_may_pull again if it is ipv6 icmp.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function ipvlan_get_L3_hdr, current codes use pskb_may_pull to
make sure the skb header has enough linear room for arp header. But it
would access the arp payload in func ipvlan_addr_lookup. So it still may
access the unepxected memory.
Now use arp_hdr_len(port->dev) instead of the arp header as the param.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano pointed that configure or show UDP_ZERO_CSUM6_RX/TX info doesn't
make sense if we haven't enabled CONFIG_IPV6. Fix it by adding
if IS_ENABLED(CONFIG_IPV6) check.
Fixes: abe492b4f5 ("geneve: UDP checksum configuration via netlink")
Fixes: fd7eafd021 ("geneve: fix fill_info when link down")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for 4.15. Most important here is the iwlwifi fix
for scan command firmware interface change.
ath10k
* fix CCMP-256, GCMP and GCMP-256 in raw mode, it was never working
wcn36xx
* fix device tree node search
iwlwifi
* fix a regression with firmware API change of scan cmd (introduced in
firmware version 34)
* add a bunch of PCI IDs and fix configuration structs for A000 devices
* fix the exported firmware name strings for 9000 and A000 devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaFZQwAAoJEG4XJFUm622bOe8H/0dmodmL+nf0MUKYyXmV2l5J
3wN0Xrse1NL3bRDTGZ/KkX/OFB1FSZ8ViGW0ek9DvbbF4lC9E5WqjM5HbTY7QE6i
bBgF476qnV9Hy/ay9SEMe7HhxsU8KfVKuYgNzY8pHhlCLkr96h35YNt+LtD319zT
PTBrxURLkZotr44mDQjO8duyKZFCafWN6F5nd22+JWpOEQDK4rUNNdDT/16CwQiy
aLqCF5bHB4kOigd9YfEpx1jO6GusqGqkB0x3lwG0QR7oygFgLZbWre0TllE+ly8P
x7gy40euxBWh9Hlk+4xjxBfZraE41XzXTTHyJECVRLKJcrlEvzCc+QCOyoYjZpY=
=uYE+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-11-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
First set of fixes for 4.15. Most important here is the iwlwifi fix
for scan command firmware interface change.
ath10k
* fix CCMP-256, GCMP and GCMP-256 in raw mode, it was never working
wcn36xx
* fix device tree node search
iwlwifi
* fix a regression with firmware API change of scan cmd (introduced in
firmware version 34)
* add a bunch of PCI IDs and fix configuration structs for A000 devices
* fix the exported firmware name strings for 9000 and A000 devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2017-11-21
This series contains fixes for igb/vf, ixgbe/vf, i40e/vf and fm10k.
Jake fixes a regression issue with older firmware, where we were using
the NVM lock to synchronize NVM reads for all devices and firmware
versions, yet this caused issues with older firmware prior to version
1.5. Fixed this by only grabbing the lock for newer devices and firmware
version 1.5 or newer.
Zijie Pan fixes the calculation of the i40e VF MAC addresses, where it was
possible to increment to the next MAC entry without calling
i40e_add_mac_filter().
Amritha removes the upper limit of 64 queues on a channel VSI since the
upper bound is determined by the VSI's num_queue_pairs.
Filip fixes an issue during FLR resets, where should have been checking
for upcoming core reset and if so, just return with I40E_ERR_NOT_READY.
Alan fixes the notifying clients of l2 parameters by copying the
parameters to the client instance struct and re-organizes the priority
in which the client tasks fire so that if the flag for notifying l2
params is set, it will trigger before the client open task. Also fixed
the promiscuous settings after reset for all the VSI's.
Brian King from IBM fixes an issue seen on Power systems which would
result in skb list corruption and eventual kernel oops. Brian
provides the same fix for nearly all our drivers, to replace the
read_barrier_depends with smp_rmb() to ensure loads are ordered with
respect to the load of tx_buffer->next_to_watch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY on BCM7278 has an additional bit that needs to be cleared:
IDDQ_GLOBAL_PWR, without doing this, the PHY remains stuck in reset out
of suspend/resume cycles.
Fixes: 0fe9933804 ("net: dsa: bcm_sf2: Add support for BCM7278 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2017-11-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several BPF offloading fixes, from Jakub. Among others:
- Limit offload to cls_bpf and XDP program types only.
- Move device validation into the driver and don't make
any assumptions about the device in the classifier due
to shared blocks semantics.
- Don't pass offloaded XDP program into the driver when
it should be run in native XDP instead. Offloaded ones
are not JITed for the host in such cases.
- Don't destroy device offload state when moved to
another namespace.
- Revert dumping offload info into user space for now,
since ifindex alone is not sufficient. This will be
redone properly for bpf-next tree.
2) Fix test_verifier to avoid using bpf_probe_write_user()
helper in test cases, since it's dumping a warning into
kernel log which may confuse users when only running tests.
Switch to use bpf_trace_printk() instead, from Yonghong.
3) Several fixes for correcting ARG_CONST_SIZE_OR_ZERO semantics
before it becomes uabi, from Gianluca. More specifically:
- Add a type ARG_PTR_TO_MEM_OR_NULL that is used only
by bpf_csum_diff(), where the argument is either a
valid pointer or NULL. The subsequent ARG_CONST_SIZE_OR_ZERO
then enforces a valid pointer in case of non-0 size
or a valid pointer or NULL in case of size 0. Given
that, the semantics for ARG_PTR_TO_MEM in combination
with ARG_CONST_SIZE_OR_ZERO are now such that in case
of size 0, the pointer must always be valid and cannot
be NULL. This fix in semantics allows for bpf_probe_read()
to drop the recently added size == 0 check in the helper
that would become part of uabi otherwise once released.
At the same time we can then fix bpf_probe_read_str() and
bpf_perf_event_output() to use ARG_CONST_SIZE_OR_ZERO
instead of ARG_CONST_SIZE in order to fix recently
reported issues by Arnaldo et al, where LLVM optimizes
two boundary checks into a single one for unknown
variables where the verifier looses track of the variable
bounds and thus rejects valid programs otherwise.
4) A fix for the verifier for the case when it detects
comparison of two constants where the branch is guaranteed
to not be taken at runtime. Verifier will rightfully prune
the exploration of such paths, but we still pass the program
to JITs, where they would complain about using reserved
fields, etc. Track such dead instructions and sanitize
them with mov r0,r0. Rejection is not possible since LLVM
may generate them for valid C code and doesn't do as much
data flow analysis as verifier. For bpf-next we might
implement removal of such dead code and adjust branches
instead. Fix from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuntap and similar devices can inject GSO packets. Accept type
VIRTIO_NET_HDR_GSO_UDP, even though not generating UFO natively.
Processes are expected to use feature negotiation such as TUNSETOFFLOAD
to detect supported offload types and refrain from injecting other
packets. This process breaks down with live migration: guest kernels
do not renegotiate flags, so destination hosts need to expose all
features that the source host does.
Partially revert the UFO removal from 182e0b6b5846~1..d9d30adf5677.
This patch introduces nearly(*) no new code to simplify verification.
It brings back verbatim tuntap UFO negotiation, VIRTIO_NET_HDR_GSO_UDP
insertion and software UFO segmentation.
It does not reinstate protocol stack support, hardware offload
(NETIF_F_UFO), SKB_GSO_UDP tunneling in SKB_GSO_SOFTWARE or reception
of VIRTIO_NET_HDR_GSO_UDP packets in tuntap.
To support SKB_GSO_UDP reappearing in the stack, also reinstate
logic in act_csum and openvswitch. Achieve equivalence with v4.13 HEAD
by squashing in commit 939912216f ("net: skb_needs_check() removes
CHECKSUM_UNNECESSARY check for tx.") and reverting commit 8d63bee643
("net: avoid skb_warn_bad_offload false positives on UFO").
(*) To avoid having to bring back skb_shinfo(skb)->ip6_frag_id,
ipv6_proxy_select_ident is changed to return a __be32 and this is
assigned directly to the frag_hdr. Also, SKB_GSO_UDP is inserted
at the end of the enum to minimize code churn.
Tested
Booted a v4.13 guest kernel with QEMU. On a host kernel before this
patch `ethtool -k eth0` shows UFO disabled. After the patch, it is
enabled, same as on a v4.13 host kernel.
A UFO packet sent from the guest appears on the tap device:
host:
nc -l -p -u 8000 &
tcpdump -n -i tap0
guest:
dd if=/dev/zero of=payload.txt bs=1 count=2000
nc -u 192.16.1.1 8000 < payload.txt
Direct tap to tap transmission of VIRTIO_NET_HDR_GSO_UDP succeeds,
packets arriving fragmented:
./with_tap_pair.sh ./tap_send_ufo tap0 tap1
(from https://github.com/wdebruij/kerneltools/tree/master/tests)
Changes
v1 -> v2
- simplified set_offload change (review comment)
- documented test procedure
Link: http://lkml.kernel.org/r/<CAF=yD-LuUeDuL9YWPJD9ykOZ0QCjNeznPDr6whqZ9NGMNF12Mw@mail.gmail.com>
Fixes: fb652fdfe8 ("macvlan/macvtap: Remove NETIF_F_UFO advertisement.")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6fa1ba6152 partially
implemented the new ethtool API, by replacing get_settings()
with get_link_ksettings(). This breaks ethtool, since the
userspace tool (according to the new API specs) never tries
the legacy set() call, when the new get() call succeeds.
All attempts to chance some setting from userspace result in:
> Cannot set new settings: Operation not supported
Implement the missing set() call.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/phy/cortina.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset we rebuild the VSIs which is going to clobber any
promiscuous settings we had before reset. This makes it so that we
restore the promiscuous settings we had before reset.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current method for notifying clients of l2 parameters is broken
because we fail to copy the new parameters to the client instance
struct, we need to do the notification before the client 'open' function
pointer gets called, and lastly we should set the l2 parameters when
first adding a client instance.
This patch first introduces the i40evf_client_get_params function to
prevent code duplication in the i40evf_client_add_instance and the
i40evf_notify_client_l2_params functions. We then fix the notify l2
params function to actually copy the parameters to client instance
struct and do the same in the *_add_instance' function. Lastly this
patch reorganizes the priority in which client tasks fire so that if the
flag for notifying l2 params is set, it will trigger before the open
because the client needs these new parameters as part of a client open
task.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch allows detection of upcoming core reset in case NIC gets
stuck while performing FLR reset. The i40e_pf_reset() function returns
I40E_ERR_NOT_READY when global reset was detected.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is safe to remove the upper limit of 64 queues on a channel
VSI. The upper bound is determined by the VSI's num_queue_pairs
and gets validated when the queue mapping info through mqprio
interface is subject to bound checking in the driver.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
num_mac should be increased only after the call to i40e_add_mac_filter().
Fixes: 5f527ba962 ("i40e: Limit the number of MAC and VLAN addresses that can be added for VFs")
Signed-off-by: Zijie Pan <zijie.pan@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 96a39aed25 ("i40e: Acquire NVM lock before
reads on all devices") we've used the NVM lock
to synchronize NVM reads even on devices which don't strictly
need the lock.
Doing so can cause a regression on older firmware prior to 1.5,
especially when downgrading the firmware.
Fix this by only grabbing the lock if we're running on an X722
device (which requires the lock as it uses the AdminQ to read
the NVM), or if we're currently running 1.5 or newer firmware.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
This changes all DEFINE_TIMER() callbacks to use a struct timer_list
pointer instead of unsigned long. Since the data argument has already been
removed, none of these callbacks are using their argument currently, so
this renames the argument to "unused".
Done using the following semantic patch:
@match_define_timer@
declarer name DEFINE_TIMER;
identifier _timer, _callback;
@@
DEFINE_TIMER(_timer, _callback);
@change_callback depends on match_define_timer@
identifier match_define_timer._callback;
type _origtype;
identifier _origarg;
@@
void
-_callback(_origtype _origarg)
+_callback(struct timer_list *unused)
{ ... }
Signed-off-by: Kees Cook <keescook@chromium.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "yuval.shaia@oracle.com" <yuval.shaia@oracle.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
* straggler timer conversions from Kees
* memory leak fix in hwsim
* fix some fallout from regdb changes if wireless is built-in
* also free aggregation sessions in startup state when station
goes away, to avoid crashing the timer
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAloS/PAACgkQB8qZga/f
l8SiZQ/+N64u2l8+2MHlAmWPCIsrCVL/jLqNPAmG45ep7mlqYsxnoghXQKw5yKxt
QodxGE8ixpih39gv3K2coPlRc+3W/C8RXlovGwoU78CCpW5EGcuzqQyh2zNCCY60
WdKjML7+KF4M3V1hQWvuunpYK97x4UN5wgf5p/e8us/kA/CR9okaIEiG0OzZ9Sb9
OItQfsWv4zwa+fYnqRHvQ1f2c+niqye9lrygo7HM639l384k4GWToFnZ0Bj4r5mO
Nmiv9l1aYXcnCIRBTJoYHm9ifL2JwokYpEEAKuhgliOhRA+CyoJCClLDpEvK2NQk
MWMcegEWDQ10kRiQOyytdO2H2XCX8Qzh8NdNLLggiG4nQgUovqrBcdnUbc9stX3P
KSZCBcvUdw3aTzs4UFU8HwG0YDnMTXZ+li/pPSad8CUvnRMr6LS/VZ/FIlPuRfLb
Ha+UraziPoSl0YMFvCCZYZ6wQ1oqWdc+0+67oczMi4KBmUumlN10qg5rEeEi2Ael
71NO2rOvMv/WYPfztQz8zuiB+g35yXAMOOY0SLFt+vfl0loWB6rRgxFjoo4dhrNv
5LtVgZiGwvedrgTIvq2CCjJN52PT51RFDzOhIR1NSOoDx3AdyeBKnulYUIED14f3
xHyOlnDbpW6B4+c0h1Hs5f4d0BMwU/dhLrUD8k4UU+qcdA4/EG8=
=jcSa
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few things:
* straggler timer conversions from Kees
* memory leak fix in hwsim
* fix some fallout from regdb changes if wireless is built-in
* also free aggregation sessions in startup state when station
goes away, to avoid crashing the timer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0115552eac ("nfp: remove false positive offloads
in flower vxlan") missed adding kdoc for a new parameter
of nfp_flower_add_offload().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel development
board (EVB). The USB id is added to qmi_wwan.c to allow QMI
communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some systems, when we unsplit a port we need to re-create two ports
instead. On other systems, only one needs to be re-created.
Do not try to create a port if during driver initialization it was
assigned a negative module number, which is invalid.
This avoids the following error during unsplit:
[ 941.012478] mlxsw_spectrum 0000:01:00.0: Port 43: Failed to map module
The error is harmless and caused by the fact that a local port is
already mapped to module 0.
Fixes: be94535f95 ("mlxsw: spectrum: Make split flow match firmware requirements")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With TC shared block changes we can't depend on correct netdev
pointer being available in cls_bpf. Move the device validation
to the driver. Core will only make sure that offloaded programs
are always attached in the driver (or in HW by the driver). We
trust that drivers which implement offload callbacks will perform
necessary checks.
Moving the checks to the driver is generally a useful thing,
in practice the check should be against a switchdev instance,
not a netdev, given that most ASICs will probably allow using
the same program on many ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mmio node was also prematurely freed.
Fixes: fd52bdae9a ("wcn36xx: Disable 5GHz for wcn3620")
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure 16-byte mic is removed from the rx data packet
tail when CCMP-256, GCMP and GCMP-256 ciphers are used
in raw decap mode. This fixed rx traffic failures in those
ciphers in raw mode. Split the helper returning crypto
tail length into two, one to get the ICV length and other
to get the mic lengh for the cipher to make it clean.
Fixes: 2ea9f12cef ("ath10k: add new cipher suite support")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
hwsim_new_radio_nl() now copies the name attribute in order to add a
null-terminator. mac80211_hwsim_new_radio() (indirectly) copies it
again into the net_device structure, so the first copy is not used or
freed later. Free the first copy before returning.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
-----BEGIN PGP SIGNATURE-----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=JPn9
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
iwlwifi: first set of fixes for 4.15
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
Some statements are not enough or too much indented.
Fix it to improve readalbility.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, ena driver would reset and re-start the device,
for example, in case of misbehaving application that causes
transmit timeout
The first step in the reset procedure is to stop the Tx traffic by
calling ena_carrier_off().
After the driver have just started the device reset procedure, device
happens to send an asynchronous notification (via AENQ) to the driver
than there was a link change (to link-up state).
This link change is mapped to a call to netif_carrier_on() which
re-activates the Tx queues, violating the assumption of no tx traffic
until device reset is completed, as the reset task might still be in
the process of queues initialization, leading to an access to
uninitialized memory.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the code to use the same green settings as in the latest
vendor driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name of functions rtl_w0w1_eri and rtl_w0w1_phy is somewhat misleading
regarding order of arguments. One could assume that w0w1 means
argument with bits to be reset comes before argument with bits to set.
However this is not the case.
So fix the order of arguments in several statements.
In addition fix EEE advertisement. The current code resets the bits
for 100BaseT and 1000BaseT EEE advertisement what is not what we want.
I have a little of a hard time to find a proper "Fixes" line as the
issue seems to have been there forever (at least it existed already
when the driver was moved to the current place in 2011).
The patch was tested on a Zotac Mini-PC with a RTL8111E-VL chip.
Before the patch EEE was disabled, now it's properly advertised and
works fine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_read_lock in tun_build_skb is used to rcu_dereference tun->xdp_prog
safely, rcu_read_unlock should be done in every return path.
Now I could see one place missing it, where it returns NULL in switch-case
XDP_REDIRECT, another palce using rcu_read_lock wrongly, where it returns
NULL in if (xdp_xmit) chunk.
So fix both in this patch.
Fixes: 761876c857 ("tap: XDP support")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
_dev_ is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after _dev_ has been null
checked.
Addresses-Coverity-ID: 1462020
Fixes: bb1b40c7cb ("usbnet: ipheth: prevent TX queue timeouts when device not ready")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Revert regression inducing change to the IPSEC template resolver,
from Steffen Klassert.
2) Peeloffs can cause the wrong sk to be waken up in SCTP, fix from Xin
Long.
3) Min packet MTU size is wrong in cpsw driver, from Grygorii Strashko.
4) Fix build failure in netfilter ctnetlink, from Arnd Bergmann.
5) ISDN hisax driver checks pnp_irq() for errors incorrectly, from
Arvind Yadav.
6) Fix fealnx driver build failure on MIPS, from Huacai Chen.
7) Fix into leak in SCTP, the scope_id of socket addresses is not
always filled in. From Eric W. Biederman.
8) MTU inheritance between physical function and representor fix in nfp
driver, from Dirk van der Merwe.
9) Fix memory leak in rsi driver, from Colin Ian King.
10) Fix expiration and generation ID handling of cached ipv4 redirect
routes, from Xin Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net: usb: hso.c: remove unneeded DRIVER_LICENSE #define
ibmvnic: fix dma_mapping_error call
ipvlan: NULL pointer dereference panic in ipvlan_port_destroy
route: also update fnhe_genid when updating a route cache
route: update fnhe_expires for redirect when the fnhe exists
sctp: set frag_point in sctp_setsockopt_maxseg correctly
rsi: fix memory leak on buf and usb_reg_buf
net/netlabel: Add list_next_rcu() in rcu_dereference().
nfp: remove false positive offloads in flower vxlan
nfp: register flower reprs for egress dev offload
nfp: inherit the max_mtu from the PF netdev
nfp: fix vlan receive MAC statistics typo
nfp: fix flower offload metadata flag usage
virto_net: remove empty file 'virtio_net.'
net/sctp: Always set scope_id in sctp_inet6_skb_msgname
fealnx: Fix building error on MIPS
isdn: hisax: Fix pnp_irq's error checking for setup_teles3
isdn: hisax: Fix pnp_irq's error checking for setup_sedlbauer_isapnp
isdn: hisax: Fix pnp_irq's error checking for setup_niccy
isdn: hisax: Fix pnp_irq's error checking for setup_ix1micro
...
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Johan Hovold <johan@kernel.org>
Reported-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the dma_mapping_error call to use the correct dma_addr
which is inside the ibmvnic_vpd struct. Moreover, it fixes an uninitialized
warning regarding a local dma_addr variable which is not used anymore.
Fixes: 4e6759be28 ("ibmvnic: Feature implementation of VPD for the ibmvnic driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When call to register_netdevice() (called from ipvlan_link_new()) fails,
we call ipvlan_uninit() (through ndo_uninit()) to destroy the ipvlan
port. After returning unsuccessfully from register_netdevice() we go
ahead and call ipvlan_port_destroy() again which causes NULL pointer
dereference panic. Fix the issue by making ipvlan_init() and
ipvlan_uninit() call symmetric.
The ipvlan port will now be created inside ipvlan_init() and will be
destroyed in ipvlan_uninit().
Fixes: 2ad7bf3638 (ipvlan: Initial check-in of the IPVLAN driver)
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
