It turns out that const and __{dev}initdata cannot be mixed currently
and that generic IDE PCI host driver is also affected by the same issue:
On Thursday 25 October 2007, Ralf Baechle wrote:
> CC drivers/ide/pci/generic.o
> drivers/ide/pci/generic.c:52: error: __setup_str_ide_generic_all_on causes a
> +section type conflict
[ Also reported by Martijn Uffing <mp3project@sarijopen.student.utwente.nl>. ]
This patch workarounds the problem in a bit hackish way but without
removing const from generic_chipsets[] (it adds const to __setup() so
__setup_str_ide_generic_all becomes const).
Now all __{dev}initdata data in generic IDE PCI host driver are read-only
so it builds again (driver's .init.data section gets marked as READONLY).
Cc: Martijn Uffing <mp3project@sarijopen.student.utwente.nl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_FORCE_LEGACY_IRQS host flag to tell ide_pci_setup_ports()
to always set hwif->irq to legacy IRQ 14/15 and convert generic IDE PCI
and via82cxxx host drivers to use it.
While at it:
* Add IDE_HFLAGS_UMC define (generic IDE PCI host driver).
* Remove no longer needed init_hwif_generic() (generic IDE PCI host driver).
* Set d->udma_mask instead of hwif->ultra_mask (via82cxxx host driver).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.
* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
method may still override them).
* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.
While at it:
* Use ATA_{UDMA,MWDMA,SWDMA}* defines.
* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.
* serverworks.c: fix DMA masks being set before checking DMA base.
v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DECLARE_GENERIC_PCI_DEV() macro to generic IDE PCI host driver
and use it to cleanup generic_chipsets[].
* Remove dead/obsolete code while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x.c: disable DMA masks for HPT345
(hwif->autodma is zero so DMA won't be enabled anyway).
* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
(hwif->autodma is zero so DMA won't be enabled anyway).
* Check noautodma global variable instead of drive->autodma in ide_tune_dma().
This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.
* Remove hwif->autodma (it was not checked by IDE core code anyway) and
drive->autodma (was set by all host drivers - except HPT345/TRM290 special
cases - unless "ide=nodma" was used).
While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
(this setting was always later over-ridden by host drivers anyway)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.
* Add IDE_HFLAG_SINGLE flag for single channel devices.
* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
and remove no longer needed ide_pci_device_t.channels field.
v2:
* Fix issues noticed by Sergei:
- correct code alignment in scc_pata.c
- s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
generic IDE PCI driver, add another device exception
This device is char device and is grabbed by generic ide driver:
00:0b.0 Class ffff: National Semiconductor Corporation 87410 IDE (rev ff) (prog-if ff)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Disallow generic IDE PCI driver to grab it by adding next condition. Also
consolidate exceptions to one bigger 'switch (dev->vendor)'.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Ingo Korb <ml@akana.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Drop ide-generic support for Jmicron identifiers as we now trust Jmicron.c for
this with drivers/ide. The code check remains for the all-generic-ide case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Jmicron JMB368 is PATA only so has the PATA on function zero. Don't
therefore skip function zero on this device when probing
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The change from __setup() to module_param_named() requires users to prefix
the option with "generic.".
This patch re-adds the __setup() additionally to the module_param_named().
Usually it would make sense getting rid of such an obsolete __setup() at
some time, but considering that drivers/ide/ is slowly approaching a RIP
status it's already implicitely scheduled for removal.
This patch fixes kernel Bugzilla #7353.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some people find their Jmicron pata port reports its disabled even
though it has devices on it and was boot probed. Fix this
(Candidate for 2.6.18.*, less so for 2.6.19 as we've got a proper
jmicron driver on the merge for that to replace ide-generic support)
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow ide/pci/generic to claim chipsets as a a module or when built-in. It
requires using "all_generic_ide" as a boot option.
Signed-off-by: Patrick Jefferson <henj@hp.com>
Acked-by: Alan Cox <alan@redhat.com>
Closes-Bug: 7017
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the IDE fix for Jmicron went in one piece went walking somewhere
(send log shows my end somehow). Without this sometimes you get an oops
on boot.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/ide/pci/generic.c:45: warning: `ide_generic_all_on' defined but not used
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds support for Netcell Revolution to pci-ide generic driver by including
it in the list of devices matched. Includes the Revolution in the list of
simplex devices forced into DMA mode.
Signed-off-by: Matt Gillette <matt.gillette@netcell.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
The ide-generic driver gives you DMA at bios tuned speed so can actually run a
lot of unsupported devices quite well. It has a pci table so that it doesn't
grab disks owned by other drivers but no way to override this. The patch adds
an option ide-generic-all which makes the driver grab everything going that is
IDE class.
The diff is messy because I put the special case as case 0 to make the if
conditional and long term maintenance easier.
This has been in Fedora for some time.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
