ib pool weren't free for various newer asic on module unload.
This doesn't cause much arm but still could be candidate for
stable.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
Revert "drm/nvc0: recognise 0xdX chipsets as NV_C0"
drm/radeon/kms: fix typo in cayman reg offset
drm/radeon/kms: use correct reg on fusion when reading back mem config
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: apply HWSTAM writes to Ivy Bridge as well
drm/i915: move IRQ function table init to i915_irq.c
drm/i915/overlay: Fix unpinning along init error paths
drm/i915: Don't call describe_obj on NULL pointers
drm/i915: Hold struct_mutex during i915_save_state/i915_restore_state
In an attempt to fix 38862 and 38863.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This lets us make the various IRQ functions static and helps avoid
problems like the one fixed in "drm/i915: Use chipset-specific irq
installers" where one of the exported functions was called rather than
the chipset specific version.
This also fixes a UMS-mode bug -- the correct irq functions for IRL
and later chips were only getting loaded in the KMS path.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
As pointed out by Dan Carpenter, it was seemingly possible to hit an error
whilst mapping the buffer for the regs (except the only likely error
returns should not happen during init) and so leak a pin count on the
bo. To handle this we would need to reacquire the struct mutex, so for
simplicity rearrange for the lock to be held for the entire function.
For extra pedagogy, test that we only call init once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The vbios rom is >64k on a lot of modern asics. Increase
the fetch size for atrm to make sure we don't miss part
of a larger rom.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They use the same register interfaces, so we can simply enable the
existing code on IVB.
v2:
- resolve conflict with ring freq scaling, we can enable it too
v3:
- resolve conflict again, this time on drm-intel-next
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Pavel Roskin <proski@gnu.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38777
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Lots of register access in these functions, some of which requires the
struct mutex.
These functions now hold the struct mutex across the calls to
i915_save_display and i915_restore_display, and so the internal mutex
calls in those functions have been removed. To ensure that no-one else
was calling them (and hence violating the new required locking
invarient), those functions have been made static.
gen6_enable_rps locks the struct mutex, and so i915_restore_state
unlocks the mutex around calls to that function.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Provide a parameter to disable hanghcheck. This is useful mostly for
developers trying to debug known problems, and probably should not be
touched by normal users.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
The ring frequency scaling table tells the PCU to treat certain GPU
frequencies as if they were a given CPU frequency for purposes of
scaling the ring frequency. Normally the PCU will scale the ring
frequency based on the CPU P-state, but with the table present, it will
also take the GPU frequency into account.
The main downside of keeping the ring frequency high while the CPU is
at a low frequency (or asleep altogether) is increased power
consumption. But then if you're keeping your GPU busy, you probably
want the extra performance.
v2:
- add units to debug table header (from Eric)
- use tsc_khz as a fallback if the cpufreq driver doesn't give us a freq
(from Chris)
v3:
- fix comments & debug output
- remove unneeded force wake get/put
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Konstantin Belousov pointed out that 4697995b98 replaced the generic
i915_driver_irq_*install() functions with chipset specific routines
accessible only through driver->irq_*install(). So update the sanity
check in i915_request_wait() to match.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The failure is as follows:
1. Userspace gets forcewake lock, lock count >=1
2. GPU hang/reset occurs (forcewake bit is reset)
3. count is now incorrect
The failure can only occur when using the forcewake userspace lock.
This has the unfortunate consequence of messing up the driver as well as
userspace, unless userspace closes the debugfs file, the kernel will
never end up waking the GT since the refcount will be > 1.
The solution is to try to recover the correct forcewake state based on
the refcount. There is a period of time where userspace reads/writes may
occur after the reset, before the GT has been forcewaked. The interface
was never designed to be a perfect solution for userspace reads/writes,
and the kernel portion is fixed by this patch.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.
Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interface to ->truncate_range is changing very slightly: once "tmpfs:
take control of its truncate_range" has been applied, this can be applied.
For now there is only a slight inefficiency while this remains unapplied,
but it will soon become essential for managing shmem's use of swap.
Change i915_gem_object_truncate() to use shmem_truncate_range() directly:
which should also spare i915 later change if we switch from
inode_operations->truncate_range to file_operations->fallocate.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soon tmpfs will stop supporting ->readpage and read_cache_page_gfp(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
Make i915_gem_object_get_pages_gtt() use shmem_read_mapping_page_gfp() in
the one place it's needed; elsewhere use shmem_read_mapping_page(), with
the mapping's gfp_mask properly initialized.
Forget about __GFP_COLD: since tmpfs initializes its pages with memset,
asking for a cold page is counter-productive.
Include linux/shmem_fs.h also in drm_gem.c: with shmem_file_setup() now
declared there too, we shall remove the prototype from linux/mm.h later.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soon tmpfs will stop supporting ->readpage and read_mapping_page(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
ttm_tt_swapin() and ttm_tt_swapout() use shmem_read_mapping_page() in
place of read_mapping_page(), since their swap_space has been created with
shmem_file_setup().
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When auditing the locking in i915_gem.c (for a prospective change which I
then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it. Since one
is in initial setup and the other in driver unload, I'm guessing the mutex
is not required for either; but post a patch in case it is.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This makes things a little clearer and prevents us from running old code
on a new chipset that may not be supported.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewied-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Two of these error paths returned without freeing "ctx".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
'drm/nouveau: rework vram init/fini ordering a little' changed
the order of instmem.init() and nouveau_mem_vram_init() which
resulted in using ramin_rsvd_vram before it was calculated and
failing to init any accel on pre-NV50 cards.
Since it's only used on <NV50 just calculate it where it's needed
and leave it as default 0 for NV50.
Signed-off-by: Younes Manton <younes.m@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's a regression from "drm/nouveau: create temp vmas for both src and
dst of bo moves".
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: save/resume forcewake lock fixes
Revert "drm/i915: Kill GTT mappings when moving from GTT domain"
drm/i915: Apply HWSTAM workaround for BSD ring on SandyBridge
drm/i915: Call intel_enable_plane from i9xx_crtc_mode_set (again)
Even if the object is no longer in the GTT domain, there may still be
a user space mapping which needs to be released.
Without this fix, render-based text (mostly in firefox) would
occasionally get corrupted when the system was under load.
Signed-off-by: Keith Packard <keithp@keithp.com>
A voltage value of 0xff01 requires that the driver
look up the max voltage for the board based using the
atom SetVoltage command table.
Setting the proper voltage should fix stability on
some newer asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The field is encoded:
0 = 4 banks
1 = 8 banks
2 = 16 banks
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Many (all?) of the coefficients related to calculating the
correct temperature are signed integers
This patch correcly parses and stores those values
It also ensures that the default offset is 0 (previously 1)
Affected cards - the original nv50 and the nv40 family
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit "drm/nouveau: add some debug output if nouveau_mm busy at destroy time"
revealed an issue where vram mm takedown would actually fail due to there
still being nodes present, causing nouveau to leak a small amount of memory
on module unload.
This splits TTM/nouveau_mm a bit more cleanly and ensures nouveau_mm fini
isn't done until all gpuobjs are also destroyed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GPU virtual addresses are constant now so this should never be getting hit
anyway and userspace shouldn't break from them being ignored.
This is being done in preference to teaching the code how to deal with BOs
that exist at different virtual addresses within separate VMs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Greatly simplifies a number of things, particularly once per-client GPU
address spaces are involved.
May add this back later once I know what things'll look like.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Was previously assuming a page size of 4KiB unless a VMA was present to
override it. Eventually, a buffer won't necessarily have a VMA at all at
some stages of its life, so we need to store this info elsewhere.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Abuses existing gpuobj_new() chan argument for this, which in turn forces
all NVOBJ_FLAG_VM allocations to be done from the global heap, not
suballocated from the channel's private heap. Not a problem though in
practise.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Userspace hasn't passed us a channel_hint for a long long time now, and
there isn't actually a need to do so anymore anyway.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On chipsets using nouveau_vm, the virtual address stays constant, so
the value set at bo creation time is fine.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's lots of boards (all recent ones) that don't have this anymore, so
punt the message to debug loglevel.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not a clue what it is yet, but we get the same numbers as NVIDIA now.
My 465 didn't seem to care to greatly *what* I bashed into these registers..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The ability to use NVIDIA's fuc has been retained *temporarily* in order
to better debug any issues that may be lingering in our initial attempt
at writing this ucode. Once I'm fairly confident we're okay, it'll be
removed.
There's a number of things not implemented by this fuc currently, but
most of it is sets of state that our context setup would not have used
anyway. No doubt we'll find out what they're for at some point, and
implement it if required.
This has been tested on 0xc0/0xc4 thus far, and from what I could tell
it worked as well as NVIDIA's. It's also been tested on 0xc1, but even
with NVIDIA's fuc that chipset doesn't work correctly with nouveau yet.
0xc3/0xc8/0xce should in theory be supported too, but I don't have the
hardware to check that.
There's no doubt numerous bugs to squash yet, please report any!
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need the physical VRAM address in vinst, even for objects mapped into
a vm, as the gpuobj suspend/resume code uses PMEM to access the object.
Previously, vinst was overloaded to mean "VRAM address" for !VM objects,
and "VM address" for VM objects, causing the wrong data to be accessed
during suspend/resume.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Until we know these should work properly, would much rather default to
noaccel than risk giving people corruption/hangs out of the box..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's issues with certain 3D apps still, unknown whether this is a kernel
issue or not.. It does appear that it may be in the 3D driver however.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes DMAR faults during accel, more than likely a similar problem to what
was solved on nv50 previously.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The lock must be held for the saving and restoring of VGA state.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
CC: Alexander Zhaunerchyk <alex.vizor@gmail.com>
CC: Andrey Rahmatullin <wrar@wrar.name>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit 4a684a4117.
Userland has always been required to set the object's domain to GTT
before using it through a GTT mapping, it's not something that the
kernel is supposed to enforce. (The pagefault support is so that we
can handle multiple mappings without userland having to pin across
them, not so that userland can use GTT after GPU domains without
telling the kernel).
Fixes 19.2% +/- 0.8% (n=6) performance regression in cairo-gl
firefox-talos-gfx on my T420 latop.
Signed-off-by: Keith Packard <keithp@keithp.com>
...we need to apply exactly the same workaround for missing interrupts
from BSD as for the BLT ring, apparently.
See also commit 498e720b96
(drm/i915: Fix gen6 (SNB) missed BLT ring interrupts).
Reported-and-tested-by: nkalkhof@web.de
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38529
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
- Add some new compute regs
- Add new dispatch packets for evergreen/cayman
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
. and some comments to make it easier to understand.
Ackedby: Randy Dunlap <randy.dunlap@oracle.com>
[v2: Added some more updates from Randy Dunlap]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
No need to assign the same copy callback for both
copy blit and dma.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Nouveau is going to use these hooks to map/unmap objects from a client's
private GPU address space.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
0xff01 is not an actual voltage value, but a flag
for the driver. If the power state as that value,
skip setting the voltage.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: fix assumption that semaphore dmaobj is valid in x-chan sync
drm/nv50/disp: fix gamma with page flipping overlay turned on
drm/nouveau/pm: Prevent overflow in nouveau_perf_init()
drm/nouveau: fix big-endian switch
Since we were calling the wptr function before checking if the IH was
even enabled, or the GPU wasn't shutdown, we'd get spam in the logs when
the GPU readback 0xffffffff. This reorders things so we return early
in the no IH and GPU shutdown cases.
Reported-and-tested-by: ManDay on #radeon
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is used during phy init to set up the phy for DP. This may
fix DP problems on DCE3.2 cards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Certain revisions of the vbios on DCE3.2 cards have a bug
in the transmitter control table which prevents duallink from
being enabled properly on some cards. The action switch statement
jumps to the wrong offset for the OUTPUT_ENABLE action. The fix
is to use the ENABLE action rather than the OUTPUT_ENABLE action
on the affected cards. In fixed version of the vbios, both
actions jump to the same offset, so the change should be safe.
Reported-and-tested-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DDX modifies DMA_SEMAPHORE on nv50 in order to implement sync-to-vblank,
things will go very wrong for cross-channel sync after this.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
While parsing the perf table, there is no check if
the num of entries read from the vbios is less than
the currently allocated number.
In case of a buggy vbios this will cause overwriting
of kernel memory, causing aditional problems.
Add a simple check in order to prevent the case
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The failure appeared in dmesg as:
[drm:i915_hangcheck_ring_idle] *ERROR* Hangcheck timer elapsed... blt
ring idle [waiting on 35064155, at 35064155], missed IRQ?
This works around that problem on by making the blitter command
streamer write interrupt state to the Hardware Status Page when a
MI_USER_INTERRUPT command is decoded, which appears to force the seqno
out to memory before the interrupt happens.
v1->v2: Moved to prior interrupt handler installation and RMW flags as
per feedback.
v2->v3: Removed RMW of flags (by anholt)
Cc: stable@kernel.org
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> [v1]
Tested-by: Eric Anholt <eric@anholt.net> [v1,v3]
(incidence of the bug with a testcase went from avg 2/1000 to
0/12651 in the latest test run (plus more for v1))
Tested-by: Kenneth Graunke <kenneth@whitecape.org> [v1]
Tested-by: Robert Hooker <robert.hooker@canonical.com> [v1]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33394
Signed-off-by: Dave Airlie <airlied@redhat.com>
The existing code assumed scratch registers in a number
of places while in most cases we are be using writeback
and events rather than scratch registers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DP clock and lanes were not set properly for DP bridges.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to set the external transmitter type properly in
AdjustPixelClock to get the properly output.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They need to be treated like eDP rather than DP.
May fix:
https://bugzilla.kernel.org/show_bug.cgi?id=34822
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to set up the bridge for DDC prior to the
i2c over aux transaction.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should give us more reliable results if the table
is called before an active device is set.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Revert commit 8f9a3f9b63. This fixes a
hang when loading the eeprom driver (see bug #35572.) GMBUS will be
re-enabled later, differently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reported-by: Marek Otahal <markotahal@gmail.com>
Tested-by: Yermandu Patapitafious <yermandu.dev@gmail.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some RS690 chipsets seem to end up with floating connectors, either
a DVI connector isn't actually populated, or an add-in HDMI card
is available but not installed. In this case we seem to get a NULL byte
response for each byte of the i2c transaction, so we detect this
case and if we see it we don't do anymore DDC transactions on this
connector.
I've tested this on my RS690 without the HDMI card installed and
it seems to work fine.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
this puts the header and followup at the same loglevel as the
hex dump code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
I don't think Apple offered any other cards for
this mac, so I doubt this will be an issue, but just
to be on the safe side, check the pci ids as well.
v2: fix spelling in commit message
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Joachim Henke <j-o@users.sourceforge.net>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 8410ea (drm: rework PCI/platform driver interface) implemented
drm_pci_irq_by_busid() but forgot to make it available in the
drm_pci_bus-struct.
This caused a freeze on my Radeon9600-equipped laptop when executing glxgears.
Thanks to Michel for noticing the flaw.
[airlied: made function static also]
Reported-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Drivers using multiple framebuffers got broken by commit
41c2e75e60 which ignored the framebuffer
(or register) map offset when looking for existing maps. The rationale
was that the kernel-userspace ABI is fixed at a 32-bit offset, so the
real offsets could not always be handed over for comparison.
Instead of ignoring the offset we will compare the lower 32 bit. Drivers
using multiple framebuffers should just make sure that the lower 32 bit
are different. The existing drivers in question are practically limited
to 32-bit systems so that should be fine for them.
It is assumed that current drivers always specify a correct framebuffer
map offset, even if this offset was ignored since above commit. So this
patch should not change anything for drivers using only one framebuffer.
Drivers needing multiple framebuffers with 64-bit map offsets will need
to cook up something, for instance keeping an ID in the lower bit which
is to be aligned away when it comes to using the offset.
All of above applies to _DRM_REGISTERS as well.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It seems to me that we are leaking 'user_pages' in
drivers/gpu/drm/i915/i915_gem.c::i915_gem_shmem_pread_slow() if
read_cache_page_gfp() fails.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To my knowledge, the limit is 16 on r300.
(the docs don't say what the limit is)
The lack of bounds checking can be abused to do all sorts of things
(from bypassing parts of the CS checker to crashing the kernel).
Bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=36745
Cc: stable@kernel.org
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Apple uses the same subsystem pci ids for lots of
hardware much of which is wired up differently. In
this case, the G5 imac and the G5 tower.
Only apply the quirk configuration to G5 towers.
Reported-by: Joachim Henke <j-o@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Joachim Henke <j-o@users.sourceforge.net>
Cc: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove an obsolete Alpha adjustment in the drm for MGA on Alpha.
Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove an obsolete Alpha adjustment, and modify another,
to go with the current Alpha architecture support.
Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com>
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
the code always returns ret regardless, so if(ret) check is unnecessary.
v2: fixed up the spelling.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Reviewed-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Improves full-screen openarena on my laptop 20.3% +/- 4.0% (n=3)
Improves 800x600 nexuiz on my laptop 12.3% +/- 0.1% (n=3)
We have more room to improve with doing LLC caching for display using
GFDT, and in doing LLC+MLC caching, but this was an easy performance
win and incremental improvement toward those two.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The simplest and common method for ensuring scanout coherency on all
chipsets is to mark the scanout buffers as uncached (and for
userspace to remember to flush the render cache every so often).
We can improve upon this for later generations by marking scanout
objects as GFDT and only flush those cachelines when required. However,
we start simple.
[v2: Move the set to uncached above the clflush. Otherwise, we'd skip
the clflush and try to scan out data that was still sitting in the
cache.]
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to perform a few operations in order to move the object into the
display plane (where it can be accessed coherently by the display
engine) that are important for future safety to forbid whilst pinned. As a
result, we want to need to perform some of the operations before pinning,
but some are required once we have been bound into the GTT. So combine
the pinning performed by all the callers with set_to_display_plane(), so
this complication is contained within the single function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[anholt v2: Don't forget that when going from cached to uncached, we
haven't been tracking the write domain from the CPU perspective, since
we haven't needed it for GPU coherency.]
[ickle v3: We also need to make sure we relinquish any fences on older
chipsets and clear the GTT for sane domain tracking.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... in preparation for changing the cache level (and thus the flags upon
the PTEs) dynamically.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like its siblings finish_gpu(), this function clears the object from the
GTT domain forcing it to be trigger a domain invalidation should we ever
need to use via the GTT again.
Note that the most important side-effect of finishing the GTT domain
(aside from clearing the tracking read/write domains) is that it imposes
an memory barrier so that all accesses are complete before it returns,
which is important if you intend to be modifying translation tables
shortly afterwards. The second most important side-effect is that it
tears down the GTT mappings forcing a page-fault and invalidation on
next user access to the object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... reincarnated from i915_gem_object_flush_gpu(). The semantic
difference is that after calling finish_gpu() the object no longer
resides in any GPU domain, and so will cause the GPU caches to be
invalidated if it is ever used again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
debug statement for GUI idle interrupt is wrong and incorrectly
reports CP EOP interrupt; trivial issue, but confusing for
someone trying to distinguish interrupt sources while debugging
... fixed
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Filter out modes that are higher than the max pixel
clock.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DRM_IOCTL_MODE_GETRESOURCES ioctl just returns bogus framebuffers.
That is because the framebuffers for each file are in the filp_head
member of struct drm_framebuffer, not in the head member.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On my x86_64 system with >4GB of ram and swiotlb instead of
a hardware iommu (because I have a VIA chipset), the call
to pci_set_dma_mask (see below) with 40bits returns an error.
But it seems that the radeon driver is designed to have
need_dma32 = true exactly if pci_set_dma_mask is called
with 32 bits and false if it is called with 40 bits.
I have read somewhere that the default are 32 bits. So if the
call fails I suppose that need_dma32 should be set to true.
And indeed the patch fixes the problem I have had before
and which I had described here:
http://choon.net/forum/read.php?21,106131,115940
Acked-by: Alex Deucher <alexdeucher@gmail.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Wierdly the kms parser never initialised the family, it wasn't really used
much, but the fmt checker patch started using it and it fell over.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv40: fall back to paged dma object for the moment
drm/nouveau: fix leak of gart mm node
drm/nouveau: fix vram page mapping when crossing page table boundaries
drm/nv17-nv40: Fix modesetting failure when pitch == 4096px (fdo bug 35901).
drm/nouveau: don't create accel engine objects when noaccel=1
drm/nvc0: recognise 0xdX chipsets as NV_C0
drm/i915: Add a no lvds quirk for the Asus EeeBox PC EB1007
drm/i915: Share the common force-audio property between connectors
drm/i915: Remove unused enum "chip_family"
drm/915: fix relaxed tiling on gen2: tile height
drm/i915/crt: Explicitly return false if connected to a digital monitor
drm/i915: Replace ironlake_compute_wm0 with g4x_compute_wm0
drm/i915: Only print out the actual number of fences for i915_error_state
drm/i915: s/addr & ~PAGE_MASK/offset_in_page(addr)/
drm: i915: correct return status in intel_hdmi_mode_valid()
drm/i915: fix regression after clock gating init split
drm/i915: fix if statement in ivybridge irq handler
* 'drm-radeon-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/atom: fix PHY init
drm/radeon/kms: add missing Evergreen texture formats to the CS parser
drm/radeon/kms: viewport height has to be even
drm/radeon/kms: remove duplicate reg from r600 safe regs
drm/radeon/kms: add support for Llano Fusion APUs
drm/radeon/kms: add llano pci ids
drm/radeon/kms: fill in asic struct for llano
drm/radeon/kms: add family ids for llano APUs
drm/radeon: fix oops in ttm reserve when pageflipping (v2)
drm/radeon/kms: clean up the radeon kms Kconfig
drm/radeon/kms: fix thermal sensor reading on juniper
drm/radeon/kms: add missing case for cayman thermal sensor
drm/radeon/kms: add blit support for cayman (v2)
drm/radeon/kms/blit: workaround some hw issues on evergreen+
* 'nouveau/drm-nouveau-fixes' of /ssd/git/drm-nouveau-next:
drm/nv40: fall back to paged dma object for the moment
drm/nouveau: fix leak of gart mm node
drm/nouveau: fix vram page mapping when crossing page table boundaries
drm/nv17-nv40: Fix modesetting failure when pitch == 4096px (fdo bug 35901).
drm/nouveau: don't create accel engine objects when noaccel=1
drm/nvc0: recognise 0xdX chipsets as NV_C0
PCI(E)GART isn't quite stable it seems, fall back to old method until I get
the time to sort it out properly.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should hopefully get modesetting at least from this, it appears these are
GF119 chipsets. Accel will come eventually, once I order a board.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The PHY was not initialized correctly after
ac89af1e10 since
the function bailed early as an encoder was not
assigned. The encoder isn't necessary for PHY init
so just assign to 0 for init so that the table
is executed.
Reported-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Tested-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I found this while figuring out why gnome-shell would not run on my
Asus EeeBox PC EB1007. As a standalone "pc" this device cleary does not have
an internal panel, yet it claims it does. Add a quirk to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
cc: stable@kernel.org
Signed-off-by: Keith Packard <keithp@keithp.com>
Make the audio property creation routine common and share the single
property between the connectors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Superseded by the tracking the render generation in the chipset
capabiltiies struct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
A tile on gen2 has a size of 2kb, stride of 128 bytes and 16 rows.
Userspace was broken and assumed 8 rows. Chris Wilson noted that the
kernel unfortunately can't reliable check that because libdrm rounds
up the size to the next bucket.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Rather than proceed on and silently return false by default, mention why
we rejected the presence of an EDID as implying the presence of a VGA
monitor. (The question arises whether there is a broken EDID which falsely
reports a digital connection when attached by VGA.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The computation of the first-level watermarks for g4x and gen5+ are
based on the same algorithm, so we can refactor those code paths to
use a single function.
Note that g4x_compute_wm0 takes a 'plane' argument while
ironlake_compute_wm0 took a 'pipe' argument. Both should have used a
'plane' argument, so this patch fixes that as well (not that it caused
a problem; ironlake always uses pipe == plane).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Convert our open coded offset_in_page() to the common macro.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
During the refactoring in revision 6067aaeadb,
the intel_enable_clock_gating was split up into several functions that are
then called indirectly. However, which function to call was not specified for
the IS_PINEVIEW() case. This patch specifies the correct gating function.
Signed-off-by: Jason Stubbs <jasonbstubbs@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The extra semicolon was not intended.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
BC6 and BC7 are described in ARB_texture_compression_bptc.
No idea what FMT_32_AS_32_32_32_32 is good for.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to take a reference to this object, pinning doesn't take a reference
so if userspace deletes the object it can disappear even if pinned.
v2: fix error paths to unreference properly also.
should fix:
https://bugzilla.kernel.org/show_bug.cgi?id=32402
and
https://bugzilla.redhat.com/show_bug.cgi?id=680651
Acked-By: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Uses a different method than other evergreen asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Allows us to use the 3D engine for memory management
and allows us to use vram beyond the BAR aperture.
v2: fix copy paste typo
Reported-by: Nils Wallménius <nils.wallmenius@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Change each shrinker's API by consolidating the existing parameters into
shrink_control struct. This will simplify any further features added w/o
touching each file of shrinker.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: fix warning]
[kosaki.motohiro@jp.fujitsu.com: fix up new shrinker API]
[akpm@linux-foundation.org: fix xfs warning]
[akpm@linux-foundation.org: update gfs2]
Signed-off-by: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
udelay() doesn't like 8-bit arguments:
drivers/gpu/drm/radeon/atom.c: In function 'atom_op_delay':
drivers/gpu/drm/radeon/atom.c:653: warning: comparison is always false due to limited range of data type
while we're there, use msleep() rather than open-coding it.
Cc: David Airlie <airlied@linux.ie>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
