Commit Graph

13337 Commits

Author SHA1 Message Date
Rémi Denis-Courmont
998ec759ef Phonet: fix netlink address dump error handling
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-11 12:55:04 -07:00
Brian Haley
cc411d0bae ipv6: Add IFA_F_DADFAILED flag
Add IFA_F_DADFAILED flag to denote an IPv6 address that has
failed Duplicate Address Detection, that way tools like
/sbin/ip can be more informative.

3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 2001:db8::1/64 scope global tentative dadfailed
       valid_lft forever preferred_lft forever

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-11 12:54:58 -07:00
Marcel Holtmann
384912ed19 net: Add DEVTYPE support for Ethernet based devices
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.

To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.

  # cat /sys/class/net/wlan0/uevent
  DEVTYPE=wlan
  INTERFACE=wlan0
  IFINDEX=5

This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.

The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-11 12:54:55 -07:00
Stephen Hemminger
4fb019a01a net: force bridge module(s) to be GPL
The only valid usage for the bridge frame hooks are by a
GPL components (such as the bridge module).
The kernel should not leave a crack in the door for proprietary
networking stacks to slip in.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-11 12:54:26 -07:00
Arnaldo Carvalho de Melo
ffcfb8db54 Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
And also do a better job of returning proper NET_{RX,XMIT}_ values.

Based on a patch and suggestions by Mark Smith.

This fixes CVE-2009-2903

Reported-by: Mark Smith <lk-netdev@lk-netdev.nosense.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-11 12:54:23 -07:00
Miklos Szeredi
8ba69ba6a3 net: unix: fix sending fds in multiple buffers
Kalle Olavi Niemitalo reported that:

  "..., when one process calls sendmsg once to send 43804 bytes of
  data and one file descriptor, and another process then calls recvmsg
  three times to receive the 16032+16032+11740 bytes, each of those
  recvmsg calls returns the file descriptor in the ancillary data.  I
  confirmed this with strace.  The behaviour differs from Linux
  2.6.26, where reportedly only one of those recvmsg calls (I think
  the first one) returned the file descriptor."

This bug was introduced by a patch from me titled "net: unix: fix inflight
counting bug in garbage collector", commit 6209344f5.

And the reason is, quoting Kalle:

  "Before your patch, unix_attach_fds() would set scm->fp = NULL, so
  that if the loop in unix_stream_sendmsg() ran multiple iterations,
  it could not call unix_attach_fds() again.  But now,
  unix_attach_fds() leaves scm->fp unchanged, and I think this causes
  it to be called multiple times and duplicate the same file
  descriptors to each struct sk_buff."

Fix this by introducing a flag that is cleared at the start and set
when the fds attached to the first buffer.  The resulting code should
work equivalently to the one on 2.6.26.

Reported-by: Kalle Olavi Niemitalo <kon@iki.fi>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-11 11:31:45 -07:00
David S. Miller
9a0da0d19c Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-next-2.6 2009-09-10 18:17:09 -07:00
Patrick McHardy
23bcf634c8 net_sched: fix estimator lock selection for mq child qdiscs
When new child qdiscs are attached to the mq qdisc, they are actually
attached as root qdiscs to the device queues. The lock selection for
new estimators incorrectly picks the root lock of the existing and
to be replaced qdisc, which results in a use-after-free once the old
qdisc has been destroyed.

Mark mq qdisc instances with a new flag and treat qdiscs attached to
mq as children similar to regular root qdiscs.

Additionally prevent estimators from being attached to the mq qdisc
itself since it only updates its byte and packet counters during dumps.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-09 18:11:23 -07:00
David S. Miller
ea6a634ef7 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 2009-09-09 17:33:45 -07:00
Holger Schurig
b2e3abdc70 cfg80211: allow scanning on specified frequencies when using wext-compatibility
Handles the case when SIOCSIWSCAN specified iw_scan_req.num_channels and
iw_scan_req.channels[].

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-09 11:25:27 -04:00
Alexey Dobriyan
fa1a9c6813 headers: net/ipv[46]/protocol.c header trim
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-09 03:43:50 -07:00
Luis R. Rodriguez
b275f28535 wireless: update cfg80211 kconfig entry
cfg80211 is now *the* wireless configuration API. Lets also
give a little explanation as to what it is and refer people to
the wireless wiki for more information.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-08 16:31:06 -04:00
David S. Miller
6ec1c69a8f net_sched: add classful multiqueue dummy scheduler
This patch adds a classful dummy scheduler which can be used as root qdisc
for multiqueue devices and exposes each device queue as a child class.

This allows to address queues individually and graft them similar to regular
classes. Additionally it presents an accumulated view of the statistics of
all real root qdiscs in the dummy root.

Two new callbacks are added to the qdisc_ops and qdisc_class_ops:

- cl_ops->select_queue selects the tx queue number for new child classes.

- qdisc_ops->attach() overrides root qdisc device grafting to attach
  non-shared qdiscs to the queues.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-06 02:07:05 -07:00
Patrick McHardy
589983cd21 net_sched: move dev_graft_qdisc() to sch_generic.c
It will be used in a following patch by the multiqueue qdisc.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-06 02:07:05 -07:00
Patrick McHardy
af356afa01 net_sched: reintroduce dev->qdisc for use by sch_api
Currently the multiqueue integration with the qdisc API suffers from
a few problems:

- with multiple queues, all root qdiscs use the same handle. This means
  they can't be exposed to userspace in a backwards compatible fashion.

- all API operations always refer to queue number 0. Newly created
  qdiscs are automatically shared between all queues, its not possible
  to address individual queues or restore multiqueue behaviour once a
  shared qdisc has been attached.

- Dumps only contain the root qdisc of queue 0, in case of non-shared
  qdiscs this means the statistics are incomplete.

This patch reintroduces dev->qdisc, which points to the (single) root qdisc
from userspace's point of view. Currently it either points to the first
(non-shared) default qdisc, or a qdisc shared between all queues. The
following patches will introduce a classful dummy qdisc, which will be used
as root qdisc and contain the per-queue qdiscs as children.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-06 02:07:03 -07:00
Patrick McHardy
5b9a9ccfad net_sched: remove some unnecessary checks in classful schedulers
The class argument to the ->graft(), ->leaf(), ->dump(), ->dump_stats() all
originate from either ->get() or ->walk() and are always valid.

Remove unnecessary checks.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-06 02:07:02 -07:00
Patrick McHardy
de6d5cdf88 net_sched: make cls_ops->change and cls_ops->delete optional
Some schedulers don't support creating, changing or deleting classes.
Make the respective callbacks optionally and consistently return
-EOPNOTSUPP for unsupported operations, instead of currently either
-EOPNOTSUPP, -ENOSYS or no error.

In case of sch_prio and sch_multiq, the removed operations additionally
checked for an invalid class. This is not necessary since the class
argument can only orginate from ->get() or in case of ->change is 0
for creation of new classes, in which case ->change() incorrectly
returned -ENOENT.

As a side-effect, this patch fixes a possible (root-only) NULL pointer
function call in sch_ingress, which didn't implement a so far mandatory
->delete() operation.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-06 02:07:02 -07:00
Patrick McHardy
71ebe5e919 net_sched: make cls_ops->tcf_chain() optional
Some qdiscs don't support attaching filters. Handle this centrally in
cls_api and return a proper errno code (EOPNOTSUPP) instead of EINVAL.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-06 02:06:12 -07:00
Patrick McHardy
c9f1d0389b net_sched: fix class grafting errno codes
If the parent qdisc doesn't support classes, use EOPNOTSUPP.
If the parent class doesn't exist, use ENOENT. Currently EINVAL
is returned in both cases.

Additionally check whether grafting is supported and remove a now
unnecessary graft function from sch_ingress.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-04 23:10:15 -07:00
Brian Haley
b1f5719558 netlink: silence compiler warning
CC      net/netlink/genetlink.o
net/netlink/genetlink.c: In function ‘genl_register_mc_group’:
net/netlink/genetlink.c:139: warning: ‘err’ may be used uninitialized in this function

From following the code 'err' is initialized, but set it to zero to
silence the warning.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-04 20:36:52 -07:00
Vlad Yasevich
f1751c57f7 sctp: Catch bogus stream sequence numbers
Since our TSN map is capable of holding at most a 4K chunk gap,
there is no way that during this gap, a stream sequence number
(unsigned short) can wrap such that the new number is smaller
then the next expected one.  If such a case is encountered,
this is a protocol violation.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:03 -04:00
Wei Yongjun
be2971438d sctp: remove dup code in net/sctp/output.c
Use sctp_packet_reset() instead of dup code.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:02 -04:00
Bhaskar Dutta
723884339f sctp: Sysctl configuration for IPv4 Address Scoping
This patch introduces a new sysctl option to make IPv4 Address Scoping
configurable <draft-stewart-tsvwg-sctp-ipv4-00.txt>.

In networking environments where DNAT rules in iptables prerouting
chains convert destination IP's to link-local/private IP addresses,
SCTP connections fail to establish as the INIT chunk is dropped by the
kernel due to address scope match failure.
For example to support overlapping IP addresses (same IP address with
different vlan id) a Layer-5 application listens on link local IP's,
and there is a DNAT rule that maps the destination IP to a link local
IP. Such applications never get the SCTP INIT if the address-scoping
draft is strictly followed.

This sysctl configuration allows SCTP to function in such
unconventional networking environments.

Sysctl options:
0 - Disable IPv4 address scoping draft altogether
1 - Enable IPv4 address scoping (default, current behavior)
2 - Enable address scoping but allow IPv4 private addresses in init/init-ack
3 - Enable address scoping but allow IPv4 link local address in init/init-ack

Signed-off-by: Bhaskar Dutta <bhaskar.dutta@globallogic.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:01 -04:00
Vlad Yasevich
8da645e101 sctp: Get rid of an extra routing lookup when adding a transport.
We used to perform 2 routing lookups for a new transport: one
just for path mtu detection, and one to actually route to destination
and path mtu update when sending a packet.  There is no point in doing
both of them, especially since the first one just for path mtu doesn't
take into account source address and sometimes gives the wrong route,
causing path mtu updates anyway.

We now do just the one call to do both route to destination and get
path mtu updates.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:01 -04:00
Vlad Yasevich
4007cc88ce sctp: Correctly track if AUTH has been bundled.
We currently track if AUTH has been bundled using the 'auth'
pointer to the chunk.  However, AUTH is disallowed after DATA
is already in the packet, so we need to instead use the
'has_auth' field.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Wei Yongjun
d521c08f4c sctp: fix to reset packet information after packet transmit
The packet information does not reset after packet transmit, this
may cause some problems such as following DATA chunk be sent without
AUTH chunk, even if the authentication of DATA chunk has been
requested by the peer.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Vlad Yasevich
31b02e1549 sctp: Failover transmitted list on transport delete
Add-IP feature allows users to delete an active transport.  If that
transport has chunks in flight, those chunks need to be moved to another
transport or association may get into unrecoverable state.

Reported-by: Rafael Laufer <rlaufer@cisco.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Vlad Yasevich
f68b2e05f3 sctp: Fix SCTP_MAXSEG socket option to comply to spec.
We had a bug that we never stored the user-defined value for
MAXSEG when setting the value on an association.  Thus future
PMTU events ended up re-writing the frag point and increasing
it past user limit.  Additionally, when setting the option on
the socket/endpoint, we effect all current associations, which
is against spec.

Now, we store the user 'maxseg' value along with the computed
'frag_point'.  We inherit 'maxseg' from the socket at association
creation and use it as an upper limit for 'frag_point' when its
set.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:21:00 -04:00
Vlad Yasevich
cb95ea32a4 sctp: Don't do NAGLE delay on large writes that were fragmented small
SCTP will delay the last part of a large write due to NAGLE, if that
part is smaller then MTU.  Since we are doing large writes, we might
as well send the last portion now instead of waiting untill the next
large write happens.  The small portion will be sent as is regardless,
so it's better to not delay it.

This is a result of much discussions with Wei Yongjun <yjwei@cn.fujitsu.com>
and Doug Graham <dgraham@nortel.com>.  Many thanks go out to them.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
b29e790728 sctp: Nagle delay should be based on path mtu
The decision to delay due to Nagle should be based on the path mtu
and future packet size.  We currently incorrectly base it on
'frag_point' which is the SCTP DATA segment size, and also we do
not count DATA chunk header overhead in the computation.  This
actuall allows situations where a user can set low 'frag_point',
and then send small messages without delay.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
d4d6fb5787 sctp: Try not to change a_rwnd when faking a SACK from SHUTDOWN.
We currently set a_rwnd to 0 when faking a SACK from SHUTDOWN.
This results in an hung association if the remote only uses
SHUTDOWNs (which it's allowed to do) to acknowlege DATA when
closing.  The reason for that is that we simply honor the a_rwnd
from the sack, but since we faked it to be 0, we enter 0-window
probing.  The fix is to use the peers old rwnd and add our flight
size to it.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
4d3c46e683 sctp: drop a_rwnd to 0 when receive buffer overflows.
SCTP has a problem that when small chunks are used, it is possible
to exhaust the receiver buffer without fully closing receive window.
This happens due to all overhead that we have account for with small
messages.  To fix this, when receive buffer is exceeded, we'll drop
the window to 0 and save the 'drop' portion.  When application starts
reading data and freeing up recevie buffer space, we'll wait until
we've reached the 'drop' window and then add back this 'drop' one
mtu at a time.  This worked well in testing and under stress produced
rather even recovery.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:59 -04:00
Vlad Yasevich
33ce828131 sctp: Clear fast_recovery on the transport when T3 timer expires.
If T3 timer expires, we are retransmitting data due to timeout any
any fast recovery is null and void.  We can clear the fast recovery
flag.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:58 -04:00
Vlad Yasevich
b9f8478682 sctp: Fix error count increments that were results of HEARTBEATS
SCTP RFC 4960 states that unacknowledged HEARTBEATS count as
errors agains a given transport or endpoint.  As such, we
should increment the error counts for only for unacknowledged
HB, otherwise we detect failure too soon.  This goes for both
the overall error count and the path error count.

Now, there is a difference in how the detection is done
between the two.  The path error detection is done after
the increment, so to detect it properly, we actually need
to exceed the path threshold.  The overall error detection
is done _BEFORE_ the increment.  Thus to detect the failure,
it's enough for the error count to match the threshold.
This is why all the state functions use '>=' to detect failure,
while path detection uses '>'.

Thanks goes to Chunbo Luo <chunbo.luo@windriver.com> who first
proposed patches to fix this issue and made me re-read the spec
and the code to figure out how this cruft really works.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:58 -04:00
Alexey Dobriyan
d71a09ed55 sctp: use proc_create()
create_proc_entry() is deprecated (not formally, though).

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:58 -04:00
Wei Yongjun
dadb50cc1a sctp: fix check the chunk length of received HEARTBEAT-ACK chunk
The receiver of the HEARTBEAT should respond with a HEARTBEAT ACK
that contains the Heartbeat Information field copied from the
received HEARTBEAT chunk. So the received HEARTBEAT-ACK chunk
must have a length of:
  sizeof(sctp_chunkhdr_t) + sizeof(sctp_sender_hb_info_t)

A badly formatted HB-ACK chunk, it is possible that we may access
invalid memory.  We should really make sure that the chunk format
is what we expect, before attempting to touch the data.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:58 -04:00
Wei Yongjun
a2f36eec56 sctp: drop SHUTDOWN chunk if the TSN is less than the CTSN
If Cumulative TSN Ack field of SHUTDOWN chunk is less than the
Cumulative TSN Ack Point then drop the SHUTDOWN chunk.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:57 -04:00
Vlad Yasevich
9c5c62be2f sctp: Send user messages to the lower layer as one
Currenlty, sctp breaks up user messages into fragments and
sends each fragment to the lower layer by itself.  This means
that for each fragment we go all the way down the stack
and back up.  This also discourages bundling of multiple
fragments when they can fit into a sigle packet (ex: due
to user setting a low fragmentation threashold).

We introduce a new command SCTP_CMD_SND_MSG and hand the
whole message down state machine.  The state machine and
the side-effect parser will cork the queue, add all chunks
from the message to the queue, and then un-cork the queue
thus causing the chunks to get transmitted.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:57 -04:00
Vlad Yasevich
5d7ff261ef sctp: Try to encourage SACK bundling with DATA.
If the association has a SACK timer pending and now DATA queued
to be send, we'll try to bundle the SACK with the next application send.
As such, try encourage bundling by accounting for SACK in the size
of the first chunk fragment.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Vlad Yasevich
e83963b769 sctp: Generate SACKs when actually sending outbound DATA
We are now trying to bundle SACKs when we have outbound
DATA to send.  However, there are situations where this
outbound DATA will not be sent (due to congestion or 
available window).  In such cases it's ok to wait for the
timer to expire.  This patch refactors the sending code
so that betfore attempting to bundle the SACK we check
to see if the DATA will actually be transmitted.

Based on eirlier works for Doug Graham <dgraham@nortel.com> and
Wei Youngjun <yjwei@cn.fujitsu.com>.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Vlad Yasevich
3e62abf92f sctp: Fix data segmentation with small frag_size
Since an application may specify the maximum SCTP fragment size
that all data should be fragmented to, we need to fix how
we do segmentation.   Right now, if a user specifies a small
fragment size, the segment size can go negative in the presence
of AUTH or COOKIE_ECHO bundling.

What we need to do is track the largest possbile DATA chunk that
can fit into the mtu.  Then if the fragment size specified is
bigger then this maximum length, we'll shrink it down.  Otherwise,
we just use the smaller segment size without changing it further.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Vlad Yasevich
bec9640bb0 sctp: Disallow new connection on a closing socket
If a socket has a lot of association that are in the process of
of being closed/aborted, it is possible for a remote to establish
new associations during the time period that the old ones are shutting
down.  If this was a result of a close() call, there will be no socket
and will cause a memory leak.  We'll prevent this by setting the
socket state to CLOSING and disallow new associations when in this state.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:56 -04:00
Doug Graham
af87b823ca sctp: Fix piggybacked ACKs
This patch corrects the conditions under which a SACK will be piggybacked
on a DATA packet.  The previous condition was incorrect due to a
misinterpretation of RFC 4960 and/or RFC 2960.  Specifically, the
following paragraph from section 6.2 had not been implemented correctly:

   Before an endpoint transmits a DATA chunk, if any received DATA
   chunks have not been acknowledged (e.g., due to delayed ack), the
   sender should create a SACK and bundle it with the outbound DATA
   chunk, as long as the size of the final SCTP packet does not exceed
   the current MTU.  See Section 6.2.

When about to send a DATA chunk, the code now checks to see if the SACK
timer is running.  If it is, we know we have a SACK to send to the
peer, so we append the SACK (assuming available space in the packet)
and turn off the timer.  For a simple request-response scenario, this
will result in the SACK being bundled with the response, meaning the
the SACK is received quickly by the client, and also meaning that no
separate SACK packet needs to be sent by the server to acknowledge the
request.  Prior to this patch, a separate SACK packet would have been
sent by the server SCTP only after its delayed-ACK timer had expired
(usually 200ms).  This is wasteful of bandwidth, and can also have a
major negative impact on performance due the interaction of delayed ACKs
with the Nagle algorithm.

Signed-off-by: Doug Graham <dgraham@nortel.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:55 -04:00
Vlad Yasevich
40187886bc sctp: release cached route when the transport goes down.
When the sctp transport is marked down, we can release the
cached route and force a new lookup when attempting to use
this transport for anything.  This way, if a better route
or source address is available, we'll try to use it.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:55 -04:00
Wei Yongjun
3cd9749c0b sctp: update the route for non-active transports after addresses are added
Update the route and saddr entries for the non-active transports as some
of the added addresses can be used as better source addresses, or may
be there is a better route.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:55 -04:00
Wei Yongjun
44e65c1ef1 sctp: check the unrecognized ASCONF parameter before access it
This patch fix to check the unrecognized ASCONF parameter before
access it.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:54 -04:00
Wei Yongjun
425e0f6852 sctp: avoid overwrite the return value of sctp_process_asconf_ack()
The return value of sctp_process_asconf_ack() may be
overwritten while process parameters with no error.
This patch fixed the problem.

Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04 18:20:54 -04:00
Cosmin Ratiu
a8fdf2b331 ipv6: Fix tcp_v6_send_response(): it didn't set skb transport header
Here is a patch which fixes an issue observed when using TCP over IPv6
and AH from IPsec.

When a connection gets closed the 4-way method and the last ACK from
the server gets dropped, the subsequent FINs from the client do not
get ACKed because tcp_v6_send_response does not set the transport
header pointer. This causes ah6_output to try to allocate a lot of
memory, which typically fails, so the ACKs never make it out of the
stack.

I have reproduced the problem on kernel 2.6.7, but after looking at
the latest kernel it seems the problem is still there.

Signed-off-by: Cosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-03 20:44:38 -07:00
Eric Dumazet
1a123a3168 vlan: adds drops accounting
Its hard to tell if vlans are dropping frames, since
every frame given to vlan_???_start_xmit() functions
is accounted as fully transmitted by lower device.

We can test dev_queue_xmit() return values to
properly account for dropped frames.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-03 20:02:17 -07:00
Eric Dumazet
55f9d6786d net: Remove debugging code
Remove a debugging aid I accidently left in previous 'cleanup' patch

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-03 05:17:20 -07:00