Add max_sectors to the driver host template and initialize it with
0xFFFF since the driver has no limitations on the size a transfer
contained by a scsi command and that fits within the sg_tablesize
provisioned by the driver. This fixes a performance issue seen in
some configurations.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug reported via SourceForge - lpfc does not load on sparc. The lpfc
driver must byteswap all FCP IOCBs to recover the data into cpu native
format.
Also correct issue of "iotag not found" messages
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Analysis:
Timeout of READ_SPARM64 causes call to lpfc_mbox_timeout_handler which
reads psli->mbox_active to determine the timeout mbox. Timeout
handler then NULL's psli->mbox_active and calls
lpfc_mbx_cmpl_read_sparam(), which on timeout condition, calls
link_down(). link_down() now calls disc_done() which calls
mbox_timeout_hander() again since WORKER_MBOX_TMO is still set, which
goes back to read psli->mbox_active which is already NULL'ed.
Remove redundant if statement in lpfc_mbox_timeout_handler. pmbox is
assigned psli->mbox_active so there is no need to check if it actually
equals psli->mbox_active.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix issue where all hosts connected to SAN get spammed with nodev
message when other initiators go away. Display nodev message only
when FC targets go away. However this behavior will be overridden if
LOG_DISCOVERY is set.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Christoph Hellwig <hch@lst.de>:
- rename PGP/HPH to lpfc_pgp/lpfc_hgp
- use __le32 types for the members to start fixing sparse -Wbitwise
issues
- remove lpfc_sli.MBhostaddr, we can always use the pointer from
SLI2_DESC directly
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The check in
627 BUG_ON(index > SG_MEMPOOL_NR);
with SG_MEMPOOL_NR defined in
32 #define SG_MEMPOOL_NR (sizeof(scsi_sg_pools)/sizeof(struct scsi_host_sg_pool))
was not sufficient.
sgp, set in
629 sgp = scsi_sg_pools + index;
is dereferenced in
630 mempool_free(sgl, sgp->pool);
Signed-off-by: Zaur Kambarov <zkambarov@coverity.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now we can change the pci core to always set this pointer, as pci drivers
should use it, not the driver core callback.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch lengthens the delay between DET setting and clearing for
COMMRESET from 400us to 1ms. I couldn't find any requiremen regarding
the duration of COMMRESET in SATA I/II specs but AHCI-1.1 10.4.2
states that it should be at least 1ms.
Signed-off-by: Tejun Heo <htejun@gmail.com>
From: Andy Whitcroft <apw@shadowen.org>
Updated to remove the bogus translated target check.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We never look at it except for the old megaraid driver that abuses it
for sending internal commands. That usage can be fixed easily because
those internal commands are single-threaded by a mutex and we can easily
use a completion there.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
it's never set to anything, and just three broken drivers are looking
at it and doing odd things.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch add the following products to the driver:
IBM ServeRAID 8i
ICP 9014R0
ICP 9024R0
ICP 9047MA
ICP 9087MA
ICP 9085LI
ICP 5085AU
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_add_host is the proper place to set the device, but people copy
the scsi_set_device usage from older drivers again and again.
note that this leaves some legacy drivers like qlogicisp/qlogicfc
without pci association in sysfs, but they're scheduled to go away soon
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use ssleep() instead of schedule_timeout to guarantee the task
delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains the following cleanups:
- make needlessly global code static
- remove or #if 0 the following unused functions:
- tul_pop_pend_scb
- tul_device_reset
- tul_reset_scsi_bus
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another rollup of patches which give various symbols static scope
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver plays with waitqueue internals and fails to compile after Ben's
"aio: make wait_queue ->task ->private" patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The fixes for sparse warnings mixed in with the fixups for
the raw_srb handler resulted in a bug that showed up in the 32 bit
environments when trying to issue calls directly to the physical devices
that are part of the arrays (ioctl scsi passthrough).
Received from Mark Salyzyn at adaptec.
Applied comment from Christoph to remove cpu_to_le32(0)
Applied Mark S fix of missing memcpy.
It applies to the scsi-misc-2.6 git tree.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Drivers need not implement a hook that returns FAILED, and does nothing
else, since the SCSI midlayer code will do that for us.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI ->done() hook should not be called from inside a spinlock.
Drivers that do this are mostly cut-n-paste from 2.2.x-era.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following the go around over the SONY DVD that needs artificial limits,
this should be the correct code for all cases (minus the debugging
prints).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
M68k: Mark Sun-3 NCR5380 SCSI broken until NCR5380_abort() and
NCR5380_bus_reset() are replaced with real new-style EH routines (the old EH
SCSI constants were removed in 2.6.12-rc3).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- the eisa layer only probes when it's actually safe, no need for
a driver option
- store the id table directly in linux format instead of convering
at runtime
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
there's absolutely no reason not to trust the driver private data
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return to previous held-logic of calling scsi_add_host() only
after the board has been completely initialized. Also return
pci_*() error-codes during probe failure paths.
This also corrects an issue where only lun 0 is being scanned for
a given port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Problem:
Incorrect md5sum when using ATAPI PIO mode to verify a distro CD.
Root cause: sg traverse problem.
In __atapi_pio_bytes(), if qc->cursg++ is increased and "goto
next_page" is executed, then sg is not updated to the new qc->cursg
and the old sg is overwritten with the new data.
Changes:
- Replace "goto next_page" with "goto next_sg" to make sg updated.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Bump sata_svw.c version number to indicate support for BCM5785(HT1000)
Southbridge SATA controller.
Signed-off-by: Narendra Sankar <nsankar@broadcom.com>
diff -uNr linux-2.6.12-rc5/drivers/scsi/sata_svw.c linux-2.6.12-rc5.brcm/drivers/scsi/sata_svw.c
This patch adds some files into the /sys/class/scsi_host/hostN
directories for aacraid adapters:
model
vendor
hba_kernel_version
hba_monitor_version
hba_bios_version
serial_number
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are several extra things that have to be considered when running
Domain Validation on a u320 target (notably how you fall back).
Hopefully this should help us when someone adds this transport class to
aic79xx.
I've tested this on the lsi1030, so I know it works correctly up to
u320.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For setting coupled parameters, we need to be comparing against the goal
settings, not the current ones.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A problem exists todayin the sg driver that if an SG_IO request is
outstanding to a device when it is removed from the system. The
system may oops if that command completes later in time.
1. sg_remove gets called
2. sg_remove calls sg_finish_req_req on all pending requests
This removes the Sg_request's from the headrp list in the Sg_fd
3. The sleeping SG_IO ioctl is woken. It does nothing and returns.
4. The caller closes the fd, which invokes sg_release
5. sg_release calls sg_remove_sfp. It finds no outstanding commands
since the headrp list is empty, so it calls __sg_remove_sfp,
which frees the sfp.
6. Now when sg_cmd_done gets called, sg uses upper_private_data in
the Scsi_Request, which should point to the srp, which has been
freed, so it points to freed memory.
7. sg then dereferences the srp pointer to get the sfp, and we oops.
The fix is to NULL out the upper_private_data field in this path,
which sg_cmd_done already checks for, which will prevent the oops
from occurring.
cpu 0x1: Vector: 300 (Data Access) at [c00000000fff7aa0]
pc: d0000000002bbea8: .sg_cmd_done+0x70/0x394 [sg]
lr: d000000000073304: .scsi_finish_command+0x10c/0x130 [scsi_mod]
sp: c00000000fff7d20
msr: 8000000000009032
dar: 2f70726f63202f78
dsisr: 40000000
current = 0xc0000000024589b0
paca = 0xc0000000003da800
pid = 7, comm = events/1
[c00000000fff7dc0] d000000000073304 .scsi_finish_command+0x10c/0x130 [scsi_mod]
[c00000000fff7e50] d00000000007317c .scsi_softirq+0x140/0x168 [scsi_mod]
[c00000000fff7ef0] c0000000000634dc .__do_softirq+0xa0/0x17c
[c00000000fff7f90] c000000000018430 .call_do_softirq+0x14/0x24
[c00000000ed472e0] c0000000000142e0 .do_softirq+0x74/0x9c
[c00000000ed47370] c000000000013c9c .do_IRQ+0xe8/0x100
[c00000000ed473f0] c00000000000ae34 HardwareInterrupt_entry+0x8/0x54
c00000000003df28 .smp_call_function+0
x100/0x1d0
[c00000000ed47780] c0000000000ba99c .invalidate_bh_lrus+0x30/0x70
[c00000000ed47810] c0000000000b91a0 .invalidate_bdev+0x18/0x3c
[c00000000ed478a0] c0000000000da7b8 .__invalidate_device+0x70/0x94
[c00000000ed47930] c0000000001d40bc .invalidate_partition+0x4c/0x7c
[c00000000ed479c0] c00000000010a944 .del_gendisk+0x48/0x15c
[c00000000ed47a50] d00000000003d55c .sd_remove+0x34/0xe4 [sd_mod]
[c00000000ed47ae0] c0000000001c5d30 .device_release_driver+0x90/0xb4
[c00000000ed47b70] c0000000001c6130 .bus_remove_device+0xb0/0x12c
[c00000000ed47c00] c0000000001c4378 .device_del+0x120/0x198
[c00000000ed47ca0] d00000000007dcdc .scsi_remove_device+0xb4/0x194 [scsi_mod]
[c00000000ed47d30] d0000000000a5864 .ipr_worker_thread+0x1d4/0x27c [ipr]
[c00000000ed47dd0] c0000000000734c4 .worker_thread+0x238/0x2f4
[c00000000ed47ee0] c0000000000796c0 .kthread+0xcc/0x11c
[c00000000ed47f90] c000000000018ad0 .kernel_thread+0x4c/0x6c
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct incorrect locking order in qla2xxx_eh_abort() handler which
would case a hang during certain code-paths.
With extra pieces to fix the irq state in the locks.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This driver wants to set PF_NOFREEZE.
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous patch did not compile cleanly on all architectures so
here's a fixed one which #includes <linux/dma-mapping.h>.
Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
diff -puN drivers/scsi/ahci.c~dma_mask-drivers_scsi_ahci drivers/scsi/ahci.c
The previous patch did not compile cleanly on all architectures so
here's a fixed one which #includes <linux/dma-mapping.h>.
Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
diff -puN drivers/scsi/sata_vsc.c~dma_mask-drivers_scsi_sata_vsc drivers/scsi/sata_vsc.c
Jens Axboe pointed out that the iounmap() call in libata was occurring
too early, and some drivers (ahci, probably others) were using ioremap'd
memory after it had been unmapped.
The patch should address that problem by way of improving the libata
driver API:
* move ->host_stop() call after all ->port_stop() calls have occurred.
* create default helper function ata_host_stop(), and move iounmap()
call there.
* add ->host_stop_prewalk() hook, use it in sata_qstor.c (hi Mark).
sata_qstor appears to require the host-stop-before-port-stop ordering
that existed prior to applying the attached patch.
Since the aic driver is now taught to speak in terms of the generic
linux devices, we can now also dispense with the transport class get
routines (since we update the parameters when the driver sees they
change) and also plumb it into the spi transport transfer agreement
reporting infrastructure.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This gives the HBA driver notice when a target is created and
destroyed to allow it to manage its own target based allocations
accordingly.
This is a much reduced verson of the original patch sent in by
James.Smart@Emulex.com
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
a) TYPE_SDAD renamed to TYPE_RBC and taken to scsi.h
b) in sbp2.c remapping of TYPE_RPB to TYPE_DISK turned off
c) relevant places in midlayer and sd.c taught to accept TYPE_RBC
d) sd.c::sd_read_cache_type() looks into page 6 when dealing with
TYPE_RBC - these guys have writeback cache flag there and are not guaranteed
to have page 8 at all.
e) sd_read_cache_type() got an extra sanity check - it checks that
it got the page it asked for before using its contents. And screams if
mismatch had happened. Rationale: there are broken devices out there that
are "helpful" enough to go for "I don't have a page you've asked for, here,
have another one". For example, PL3507 had been caught doing just that...
f) sbp2 sets sdev->use_10_for_rw and sdev->use_10_for_ms instead
of bothering to remap READ6/WRITE6/MOD_SENSE, so most of the conversions
in there are gone now.
Incidentally, I wonder if USB storage devices that have no
mode page 8 are simply RBC ones. I haven't touched that, but it might
be interesting to check...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sym2 version 2.2.1:
- Fix MMIO BAR detection (Thanks to Bob Picco)
- Fix odd-sized transfers with a wide bus (Thanks to Larry Stephens)
- Write posting fixes (Thanks to Thibaut Varene)
- Change one of the GFP_KERNEL allocations back into a GFP_ATOMIC
- Make CCB_BA() return a script-endian address
- Move range checks and disabling of devices from the queuecommand path
to slave_alloc()
- Remove a warning in sym_setup_cdb()
- Keep a pointer to the scsi_target instead of the scsi_dev in the tcb
- Remove a check for the upper layers passing an oversized cmd
- Replace CAM_REQ_ constants with the Linux DID_ constants
- Replace CAM_DIR_ constants with the Linux DMA_ constants
- Inline sym_read_parisc_pdc() on non-parisc systems
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Stuart Hayes <Stuart_Hayes@dell.com>
The system can panic with a null pointer dereference using ide-scsi if
PIO is being done on scatter gather pages that are in high memory,
because page_address() returns 0. We are actually seeing this using a
tape drive. This patch will kmap_atomic() the pages before performing
PIO.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
* add ide_bus_match() and export ide_bus_type
* split ide_remove_driver_from_hwgroup() out of ide_unregister()
* move device cleanup from ide_unregister() to drive_release_dev()
* convert ide_driver_t->name to driver->name
* convert ide_driver_t->{attach,cleanup} to driver->{probe,remove}
* remove ide_driver_t->busy as ide_bus_type->subsys.rwsem
protects against concurrent ->{probe,remove} calls
* make ide_{un}register_driver() void as it cannot fail now
* use driver_{un}register() directly, remove ide_{un}register_driver()
* use device_register() instead of ata_attach(), remove ata_attach()
* add proc_print_driver() and ide_drivers_show(), remove ide_drivers_op
* fix ide_replace_subdriver() and move it to ide-proc.c
* remove ide_driver_t->drives, ide_drives and drives_lock
* remove ide_driver_t->drivers, drivers and drivers_lock
* remove ide_drive_t->driver and DRIVER() macro
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
When testing ATAPI PIO data transfer on the ppc64 platform, __atapi_pio_bytes() got zero when
sg_dma_len() is used. I checked the <asm-ppc64/scatterlish.h>, the struct scatterlist is defined as:
struct scatterlist {
struct page *page;
unsigned int offset;
unsigned int length;
/* For TCE support */
u32 dma_address;
u32 dma_length;
};
#define sg_dma_address(sg) ((sg)->dma_address)
#define sg_dma_len(sg) ((sg)->dma_length)
So, if the scatterlist is not DMA mapped, sg_dma_len() will return zero on ppc64.
The same problem should occur on the x86-64 platform.
On the i386 platform, sg_dma_len() returns sg->length, that's why the problem does not occur on an i386.
Changes:
- Use sg->length if the scatterlist is not DMA mapped (yet).
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
BCM5785 (HT1000) is a new southbridge from Serverworks/Broadcom that
incorporates 4 SATA ports in a single PCIX function. Functionally these
ports are similar to that in older devices like the Apple K2 and the
Frodo4/8. This patch adds support for the new PCI device ID along with a
blurb on what the various device IDs mean. Additionally in all devices
based on this SATA controller, the SATA ports appear as a single PCI
function. This is true for older Frodo8 devices as well. Hence the init
function should init all the ports present in the detected controller
(which could be 4 or 8).
Signed-off-by: Narendra Sankar <nsankar@broadcom.com>
Fix a c99ism.
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new period/dt setting routines don't get the coupling of these
parameters correct. This means that Domain Validation never gets DT
set, and thus the drive gets restricted to U80.
Fix this by restoring the couplings in the set routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Tampering with the settings has to be done under the host lock ...
slave_alloc isn't called under any lock, so this has to be done
explicitly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The allocation of all of our components should be done in slave alloc.
Currently it's rather fancifully refcounted in the queuecommand
callback. This patch moves allocation and destroy to their correct
places in slave_alloc/slave_destory. Now we can guarantee that
everywhere a device is requested, it's actually been allocated, so don't
check for this anymore.
Additionally, the per device busy timer was the only source of potential
use after free. It's been deleted because Linux does the correct thing
with busy returns, so there's no need to implement a separate timer in
the driver.
Finally, implement code that forces all the device parameters to zero
(i.e. async and narrow) in the slave alloc, inform the spi class of the
bios recorded maximums and wait until slave configure before trying
anything more adventurous.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This should finish the spurious queue removal from aic7xxx (there are
other queues that are probably unnecessary, but at least the major and
obviously unnecessary ones are done with).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This was rendered obsolete by the busyq removal; remove some of the last
remnants of its presence.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
pci_alloc_consistent is under 4G by default. Also simplify the
definition of bus_dmamap_t.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's not much sense in sharing code anymore now that aic7xxx uses
various transport class facilities.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The aic7xxx driver has two spurious queues in it's linux glue code: the
busyq which queues incoming commands to the driver and the completeq
which queues finished commands before sending them back to the mid-layer
This patch just removes the busyq and makes the aic finally return the
correct status to get the mid-layer to manage its queueing, so a command
is either committed to the sequencer or returned to the midlayer for
requeue.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is similar to the previous sym2 problem. For Domain Validation to
work we can't allow any period setting to turn wide on if it was
previously off.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a basic need not to have parameters go under or over certain
values when doing domain validation. The basic ones are
max_offset, max_width and min_period
This patch makes the transport class take and enforce these three
limits. Currently they can be set by the user, although they could
obviously be read from the HBA's on-board NVRAM area during
slave_configure (if it has one).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New code from the Adaptec driver. Performance enhancement for newer
adapters. I hope that this isn't too big for a single patch. I believe
that other than the few small cleanups mentioned, that the changes are
all related.
- Added Variable FIB size negotiation for new adapters.
- Added support to maximize scatter gather tables and thus permit
requests larger than 64KB/each.
- Limit Scatter Gather to 34 elements for ROMB platforms.
- aac_printf is only enabled with AAC_QUIRK_34SG
- Large FIB ioctl support
- some minor cleanup
Passes sparse check.
I have tested it on x86 and ppc64 machines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Save and restore the scmd->result, so that timed out commands do not
return the result of the TEST UNIT READY or the start/stop commands. Code
is already in place to save and restore the result for the request sense
case.
The previous version of this patch erroneously removed the "if" check,
instead add a comment as to why the "if" is needed.
Signed-off-by: Patrick Mansfield <patmans@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_queue_insert() has four callers. Three callers call with
timer disabled and one (the second invocation in
scsi_dispatch_cmd()) calls with timer activated.
scsi_queue_insert() used to always call scsi_delete_timer()
and ignore the return value. This results in race with timer
expiration. Remove scsi_delete_timer() call from
scsi_queue_insert() and make the caller delete timer and check
the return value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
'if' tests which check if eh_action isn't NULL in both
functions are always true. Remove the redundant if's as it
can give wrong impressions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_reset_provider() calls scsi_delete_timer() on exit which
isn't necessary. Remove it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here is a incremental patch which switches the driver over to
the new non-simple functions. Compile-tested.
Signed-off-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a device driver for scsi media changer devices.
Signed-off-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, during PCI hotplug remove, if the upper layer
drivers of the attached devices send commands down as part
of the remove action, like a CDROM, the hotplug action
will hang forever due to the ipr driver returning
SCSI_MLQUEUE_HOST_BUSY. Patch fixes this.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker found that this for loop was wrong.
This patch changes it to what seems to be intended.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is against 2.6.12-rc3 + linus-patch from April 30. The patch
contains the following fixes:
- CAP_SYS_RAWIO is used instead of CAP_SYS_ADMIN; fix from Alan Cox
- only direct sending of SCSI commands requires this permission
- the st status is modified is successful unload is performed using
SCSI_IOCTL_STOP_UNIT
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bugme 4547. The following patch fixes a bug in ipr's error logging.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I discovered that the qla1280 driver does not send the correct status
to the midlayer when it gets Queue Full or Busy from a device.
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch addresses the sparse -Wbitwise warnings that Christoph wanted
me to eliminate. This mostly consisted of making data structure
elements of hardware associated structures the __le* equivalent.
Although there were a couple places where there was mixing of cpu and le
variable math. These changes have been tested on both an x86 and ppc
machine running bonnie++. The usage of the LE32_ALL_ONES macro has been
eliminated.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes the following warnings:
drivers/scsi/dpt_i2o.c: In function ‘adpt_isr’:
drivers/scsi/dpt_i2o.c:2030: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2031: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2042: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2043: warning: passing argument 2 of ‘writel’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2046: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2048: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2055: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2062: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2069: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c: In function ‘adpt_i2o_to_scsi’: drivers/scsi/dpt_i2o.c:2239: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2243: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2248: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2259: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
It define variables which are only used with a type of 'void __iomem *'
with this type instead of the incorrect 'unsigned long' type.
It also remove pointless casts.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes the array 'hbas' as it seems to be useless
and redundant with the linked list hbas_chain.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Adrian Bunk <bunk@stusta.de>
This patch contains cleanups including the following:
- remove #ifdef'ed code for other OS's
- remove other unused code
- make needlessly global code static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes a needlessly global struct static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes a needlessly global function static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_queue_insert() used to use blk_insert_request() for requeueing
requests. This depends on the unobvious behavior of
blk_insert_request() setting REQ_SPECIAL and REQ_SOFTBARRIER when
requeueing. This patch makes scsi_queue_insert() use
blk_requeue_request(). As REQ_SPECIAL means special requests and
REQ_SOFTBARRIER is automatically handled by blk layer now, no flag
needs to be set.
Note that scsi_queue_insert() now calls scsi_run_queue() itself, and
the prototype of the function is added right above
scsi_queue_insert(). This is temporary, as later requeue path
consolidation patchset removes scsi_queue_insert(). By adding
temporary prototype, we can do away with unnecessarily moving
functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_requeue_request() used to use blk_insert_request() for requeueing
requests. This depends on the unobvious behavior of
blk_insert_request() setting REQ_SPECIAL and REQ_SOFTBARRIER when
requeueing. This patch makes scsi_queue_insert() use
blk_requeue_request(). As REQ_SPECIAL means special requests and
REQ_SOFTBARRIER is automatically handled by blk layer now, no flag
needs to be set.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
blk_insert_request() has a unobivous feature of requeuing a
request setting REQ_SPECIAL|REQ_SOFTBARRIER. SCSI midlayer
was the only user and as previous patches removed the usage,
remove the feature from blk_insert_request(). Only special
requests should be queued with blk_insert_request(). All
requeueing should go through blk_requeue_request().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_init_io() used to set REQ_SPECIAL when it fails sg
allocation before requeueing the request by returning
BLKPREP_DEFER. REQ_SPECIAL is being updated to mean special
requests. So, remove REQ_SPECIAL setting.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original from: Christoph Hellwig <hch@lst.de>
Modified and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Christoph Hellwig <hch@lst.de>
Both drivers are marked broken and haven't compiled since very early
2.5.x. And they're for IDE hardware so they shouldn't have been
written to the SCSI layer at all.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
