During link down, iscsid tries to do re-login to failed session. In case of
link down-up-down, LLD was sending connection login failed event to iscsid,
which is destroying the session, instead we have to continue re-login by
sending connection err event.
JIRA Key: UPSISCSI-134
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Unable to login to session if login-logout issued consecutively for
multiple sessions. Solution is to clear idx in DDB map on the basis
of no-active connection asynchronous event (AEN).
JIRA Key: UPSISCSI-135
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Firmware reserves DDBs if there are entries in the FLASH.
So there are no free DDBs left when a iSCSI login is initiated
by user space tool like iscsiadm.
Since now login is not controlled by firmware, LLD need to free
up the DDBs after firmware init. This will ensure free DDBs are
available for iSCSI logins using iscsiadm.
JIRA Key: UPSISCSI-151
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If a boot target has a BIDI CHAP enabled, then read the user/secret from
CHAP table. Do not assume BIDI chap at peer CHAP index + 1
JIRA Key: UPSISCSI-156
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver failed to export primary boot target if secondary target did not
exist in the FLASH. If boot targets are not valid then driver assumed 0 and
1 as default boot targets. Since these target did not exist in flash, the
driver failed exporting all the targets.
JIRA Key: UPSISCSI-148
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
QLogic applications store the CHAP information in FLASH. During login,
authentication information is provided using an index into the CHAP region.
In order to support QLogic applications along with iscsiadm, updated the
LLD to not add duplicate CHAP entries in the CHAP region and preserve the
existing CHAP info in the CHAP region in FLASH.
This allows QLogic applications to pre-write the CHAP entries in the
CHAP region.
With iscsiadm, when the CHAP authentication information is sent to the LLD, the
LLD searches for the entry in CHAP region in FLASH, if exists then do not add.
If CHAP entry does not exist then add the CHAP entry in the CHAP region.
JIRA Key: UPSISCSI-146
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver was not setting the bidirectional CHAP bit correctly in
the DDB entry.
JIRA Key: UPSISCSI-108
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla4xxx now uses iscsi_boot_sysfs to export the targets used
for boot to sysfs. It needs to select that config option
to make sure that module is also built.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Export the name of iface session is attached to. This is needed
so tools like iscsiadm/iscsistart can match the sessions to
userspace ifaces when rebuilding iscsid's state during boot.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This command is used to read ACB params from firmware
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This command will causes the firmware to update all
configurations to pre-defined factory default settings.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hook qla4xxx in fw boot sysfs interface so iscsi tools
can use the info to create boot sessions.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1. Remove device database entry (ddb) state.
2. Remove device database (DDB) list building.
With open-iscsi integration the logins to the target devices are
handled by the user space. So the information of target is now
maintained in the iscsi_session object. This is handled at
libiscsi level so there is no need to maintain a list of DDBs in
the qla4xxx LLD.
3. qla4xxx: Remove add_device_dynamically.
Since autologin in FW is disabled with open-iscsi integration,
driver will never get an AEN for which driver has not requested
a DDB index. So remove the add_device_dynamically function.
4. Remove qla4xxx_tgt_dscvr
Since firmware autologin is disabled this function will not work.
Now user has the ability to do the target discovery and login to
each target individually. Firwmare will not do the login on its own.
5. Remove relogin related code
All relogin is handled by userspace now. qla4xxx just need to
notify userspace of a connection failure, this triggers the
relogin.
6. Remove add_session and alloc_session
Now qla4xxx uses iscsi_session_setup that would do the necessary
allocations for session and ddb_entry.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add scsi_transport_iscsi hooks in qla4xxx to support
iSCSI session management using iscsiadm.
This patch is based on discussion here
http://groups.google.com/group/open-iscsi/browse_thread/thread/e89fd888baf656a0#
Now users can use iscsiadm to do target discovery and do login/logout to
individual targets using the qla4xxx iSCSI class interface.
This patch leaves some dead code, but to make it easier to review
we are leaving and in the next patch we will remove that old code.
V2 - NOTE: Added code to avoid waiting for AEN during login/logout
in the driver, instead added a kernel to user event
to notify iscsid about login status. Because of this
iscsid will not get blocked.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds bsg support to qla4xxx.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to set VLAN and show vlan settings in sysfs
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[Patch updated to new defines]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We can replace the iface param mask with the
attr_is_visible callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Move all ipaddress related param to "struct ipaddress_config"
from "struct scsi_qla_host"
- update function - qla4xxx_update_local_ip()
- Rename IPOPT_IPv4_PROTOCOL_ENABLE to IPOPT_IPV4_PROTOCOL_ENABLE
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
[update for new ISCSI_IFACE values]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patches from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The presense of a writeq() implementation on 32-bit x86 that splits the
64-bit write into two 32-bit writes turns out to break the mpt2sas driver
(and in general is risky for drivers as was discussed in
<http://lkml.kernel.org/r/adaab6c1h7c.fsf@cisco.com>). To fix this,
revert 2c5643b1c5 ("x86: provide readq()/writeq() on 32-bit too") and
follow-on cleanups.
This unfortunately leads to pushing non-atomic definitions of readq() and
write() to various x86-only drivers that in the meantime started using the
definitions in the x86 version of <asm/io.h>. However as discussed
exhaustively, this is actually the right thing to do, because the right
way to split a 64-bit transaction is hardware dependent and therefore
belongs in the hardware driver (eg mpt2sas needs a spinlock to make sure
no other accesses occur in between the two halves of the access).
Build tested on 32- and 64-bit x86 allmodconfig.
Link: http://lkml.kernel.org/r/x86-32-writeq-is-broken@mdm.bga.com
Acked-by: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Acked-by: James Bottomley <James.Bottomley@parallels.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since queue_work does not requeue, there is no need to check
if a work is in progress using the AF_DPC_SCHEDULED flag.
queue_work would return if work is pending without adding the
work, do_dpc would again get invoked from qla4xxx_timer if
there is still DPC flags set.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Corrected logic to don't check for F/W is alive if reset is already
in progress for ISP82XX
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Do not process interrupt unconditionally during mailbox processing which can
lead to spurious interrupt. Mailbox completion are now polled if interrupt are
disabled or wait for interrupt to come in if its enabled
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Complete the cmd if sense length is zero. For cases where sense
data spans across multiple iocb's by FW, we need to hold on to the
I/O (ha->status_srb != NULL) till we have processed them all and
copied the sense data from internal buffer to scsi_cmd sense buffer.
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
- Added MBOX_ASTS_DUPLICATE_IP AEN handling.
- Update MBOX_AEN_REG_COUNT to 8 so that driver will save status
of all mbox registers in aen_q
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Disable Interrupt MBX completion will disable the interrupt on
successful completion. Fixed the bug where driver was waiting for
Interrupt to come in for its completion. Now driver will poll for
disable interrupt MBX completion.
Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
