Commit Graph

1066 Commits

Author SHA1 Message Date
Samu Onkalo
32496c76b7 lis3: scale output values to mg
Report output values as 1/1000 of earth gravity.

Output values from lis3 can be read from sysfs position entry and from
input device.  Input device can be accessed as event device and as
joystick device.  Joystick device can be in two modes.  Meaning of the
output values varies from case to case depending on the chip type and
configuration (scale).  Only joystick interface in JS_CORR_BROKEN mode
returned somehow similar output values in different configurations.
Joystick device is in that state by default in case of lis3.

Position sysfs entry, input event device and raw joystick device have been
little bit broken since meaning of the output values has been varied
between 12 and 8 bit devices.  Applications which relayed on those methods
failed if the chip is different than the expected one.

This patch converts output values to mean similar thing in different
configurations.  Both 8 and 12 bit devices reports now same acceleration
values.  If somebody implements full scale support to the driver, output
values will still mean the same.  Scaling factor and input device range
must be updated in that case.

Joystick interface in JS_CORR_BROKEN mode is not touched by this patch.
All other interfaces have different scale after this change.  For 12 bit
device scaling factor is 0.977 which keeps scaled and unscaled values are
quite close to each others.  For 8 bit device, scaled values are 18 times
bigger than unscaled values.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:36 -08:00
Samu Onkalo
a253aaef60 lis3: sysfs entry for setting chip measurement rate
It is possible to read position information at the chip measurement rate
via sysfs.  This patch adds possibility to configure chip measurement
rate.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:36 -08:00
Samu Onkalo
539954120b lis3lv02d: remove calibaration functionality
Chip is calibrated by the manufacturer.  There is no need to calibarate it
at driver level.  If the chip is used as a joystick, calibaration can be
done using joystick device calibration mechanism.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:36 -08:00
Samu Onkalo
2db4a76d5f lis3: selftest support
Implement selftest feature as specified by chip manufacturer.  Control:
read selftest sysfs entry

Response: "OK x y z" or "FAIL x y z"

where x, y, and z are difference between selftest mode and normal mode.
Test is passed when values are within acceptance limit values.

Acceptance limits are provided via platform data.  See chip spesifications
for acceptance limits.  If limits are not properly set, OK / FAIL decision
is meaningless.  However, userspace application can still make decision
based on the numeric x, y, z values.

Selftest is meant for HW diagnostic purposes.  It is not meant to be
called during normal use of the chip.  It may cause false interrupt
events.  Selftest mode delays polling of the normal results but it doesn't
cause wrong values.  Chip must be in static state during selftest.  Any
acceration during the test causes most probably failure.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:36 -08:00
Samu Onkalo
641615abfa lis3lv02d: proper power on sequence
Lis3 accelerometer sensors have quite long power on delay (up to 125
ms). This patch adds necessary delay to power on sequence for currently
supported lis3 chips.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:36 -08:00
Éric Piel
4b5d95b380 lis3: fix show rate for 8 bits chips
Originally the driver was only targeted to 12bits sensors.  When support
for 8bits sensors was added, some slight difference in the registers were
overlooked.  This should fix it, both for initialization, and for
displaying the rate.

Reported-by: Kalhan Trisal <kalhan.trisal@intel.com>
Reported-by: Christoph Plattner <christoph.plattner@gmx.at>
Tested-by: Christoph Plattner <christoph.plattner@gmx.at>
Tested-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:36 -08:00
Éric Piel
bc62c14717 lis3: update documentation and comments
Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.

Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:36 -08:00
Samu Onkalo
66c8569bf9 lis3lv02d: correct memory leak in module unload
polled input device itself was not free'd.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:36 -08:00
Samu Onkalo
d25a8c8115 lis3lv02d: send sync event
Send input_sync after each measurement round. This helps userspace to
detect which reported values belongs to the same measurement.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Acked-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:35 -08:00
Daniel J Blueman
41e9a06236 hwmon: w83627ehf updates
Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level.  Add control of rate of change of fan output
level.  These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority.  Add
support for constant fan speed and proportional-response operations modes.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:35 -08:00
Alexey Dobriyan
471452104b const: constify remaining dev_pm_ops
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:25 -08:00
Jean Delvare
e5e9f44c24 i2c: Drop I2C_CLIENT_INSMOD_2 to 8
These macros simply declare an enum, so drivers might as well declare
it themselves. This puts an end to the arbitrary limit of 8 chip types
per i2c driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
2009-12-14 21:17:27 +01:00
Jean Delvare
1f86df49dd i2c: Drop I2C_CLIENT_INSMOD_1
This macro simply declares an enum, so drivers might as well declare
it themselves.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
2009-12-14 21:17:26 +01:00
Jean Delvare
c3813d6af1 i2c: Get rid of struct i2c_client_address_data
Struct i2c_client_address_data only contains one field at this point,
which makes its usefulness questionable. Get rid of it and pass simple
address lists around instead.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
2009-12-14 21:17:25 +01:00
Jean Delvare
310ec79210 i2c: Drop the kind parameter from detect callbacks
The "kind" parameter always has value -1, and nobody is using it any
longer, so we can remove it.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
2009-12-14 21:17:23 +01:00
Linus Torvalds
f71eaf6840 Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (41 commits)
  hwmon: (adt7475) Add VID support for the ADT7476
  hwmon: (adt7475) Add an entry in MAINTAINERS
  hwmon: (adt7475) Add support for the ADT7476
  hwmon: (adt7475) Voltage attenuators can be bypassed
  hwmon: (adt7475) Print device information on probe
  hwmon: (adt7475) Handle alternative pin functions
  hwmon: (adt7475) Move sysfs files removal to a separate function
  hwmon: (adt7475) Add support for the ADT7490
  hwmon: (adt7475) Improve device detection
  hwmon: (adt7475) Add missing static marker
  hwmon: (adt7475) Rework voltage inputs handling
  hwmon: (adt7475) Implement pwm_use_point2_pwm_at_crit
  hwmon: (adt7475) New documentation
  hwmon: (adt7475) Add support for the ADT7473
  hwmon: (f71882fg) Add support for the f71889fg (version 2)
  hwmon: (f71882fg) Fix sysfs file removal
  hwmon: (f71882fg) Cleanup sysfs attr creation 2/2
  hwmon: (f71882fg) Cleanup sysfs attr creation 1/2
  hwmon: (thmc50) Stop using I2C_CLIENT_MODULE_PARM
  hwmon: Add Freescale MC13783 ADC driver
  ...
2009-12-09 19:53:11 -08:00
Jean Delvare
54fe4671aa hwmon: (adt7475) Add VID support for the ADT7476
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:08 +01:00
Jean Delvare
d8d2ee0732 hwmon: (adt7475) Add support for the ADT7476
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:08 +01:00
Jean Delvare
ebfaf1fbb6 hwmon: (adt7475) Voltage attenuators can be bypassed
It is possible to bypass the voltage attenuators on the +2.5V, Vccp,
+5V and +12V voltage monitoring inputs. This is useful to connect
other voltage channels than the ones the monitoring chip was
originally designed for. When this feature is enabled, we must not
include the scaling factors in our computations.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:07 +01:00
Jean Delvare
d07ca4ad2f hwmon: (adt7475) Print device information on probe
Print the device name and revision at probe time, as well as a list of
all optional features which are available.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:07 +01:00
Jean Delvare
378933c994 hwmon: (adt7475) Handle alternative pin functions
The TACH4 pin can be used for other functions, so fan4 may not always
be available. Likewise, the PWM2 pin can be used for ALERT output, in
which case pwm2 is not available

For the ADT7490, the +2.5 Vin pin may also be used for other
functions, in which case in0 is not available.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:06 +01:00
Jean Delvare
0f14480b62 hwmon: (adt7475) Move sysfs files removal to a separate function
Move sysfs files removal to a separate function. The code is common to
the device probing error path and the standard device removal path. As
it will grow with future driver development, this avoids code
duplication.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:06 +01:00
Jean Delvare
3d84998171 hwmon: (adt7475) Add support for the ADT7490
Add support for the Analog Devices ADT7490 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 6 voltage inputs instead of 2.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:05 +01:00
Jean Delvare
d656b6fde2 hwmon: (adt7475) Improve device detection
Check the value of register 0x3f as part of the device detection, to
make it more robust.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:04 +01:00
Jean Delvare
54ecb9e3c1 hwmon: (adt7475) Add missing static marker
adt7475_attr_group is used internally only and can thus be marked
static.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:03 +01:00
Jean Delvare
cffb9dd07f hwmon: (adt7475) Rework voltage inputs handling
Rework the handling of voltage inputs to make it possible and easy to
support more inputs. This will be needed for the upcoming ADT7490
support.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:03 +01:00
Jean Delvare
f99318b254 hwmon: (adt7475) Implement pwm_use_point2_pwm_at_crit
Implement the non-standard pwm_use_point2_pwm_at_crit sysfs attribute
as the adt7473 driver did.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:03 +01:00
Jean Delvare
b180d05084 hwmon: (adt7475) Add support for the ADT7473
Add support for the ADT7473 to the adt7475 driver, and mark the
adt7473 driver for removal. The ADT7473 and ADT7475 chips are almost
the same chip and essentially compatible, so there's no point in
having separate drivers for them.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
2009-12-09 20:36:02 +01:00
Hans de Goede
7669896f49 hwmon: (f71882fg) Add support for the f71889fg (version 2)
This adds support for the Fintek f71889fg to the f71882fg driver,
many thanks to Gerd v. Egidy for providing (remote) access to a
machine which such an ic.

Note that this bit of the patch:
-	val = SENSORS_LIMIT(val, 0, 255);
+
+	if (data->type == f71889fg)
+		val = SENSORS_LIMIT(val, -128, 127);
+	else
+		val = SENSORS_LIMIT(val, 0, 127);

Changes behaviour for already supported models, the new behaviour is correct
as the already supported models have bit 7 of the involved registers fixed at
0, so the previous behaviour which allowed setting temp zone limits > 127
was not correct.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:36:01 +01:00
Hans de Goede
fc16c56e69 hwmon: (f71882fg) Fix sysfs file removal
There is a bug in the old sysfs file removal, as it uses fxxxx_in_temp_attr
to remove the in and temp sysfs attributes, but fxxxx_in_temp_attr has
temp#_alarm, where as f71858fg_in_temp_attr has temp#_max_alarm, so
the temp#_max_alarm attributes for the f71858fg never get removed.

This patch fixes this by doing the sysfs removal exactly the same way as
the creation instead of being (too) clever, this will also avoid similar
bugs in the future.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:36:01 +01:00
Hans de Goede
b69b039922 hwmon: (f71882fg) Cleanup sysfs attr creation 2/2
This patch merges the f71882fg_auto_pwm_attr array into the
fxxxx_fan_attr resp. fxxxx_auto_pwm_attr array, as the f71882fg_auto_pwm_attr
array was merely extending these 2 with entries for a 4th fan, it also makes
these 2 arrays 2 dimensional so that the rest of the code can choose to
add attr for 3 or 4 fans without needing to know the nr of attr per fan.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:36:00 +01:00
Hans de Goede
66344aa6ad hwmon: (f71882fg) Cleanup sysfs attr creation 1/2
This patch makes a number of cleanups to the sysfs attr creation
in the f71882fg driver, this is a preparation patch for adding f71889fg
support:

* Add some comments to explain why some models need separate sysfs attr
  arrays for in / temp / fan / pwm
* Rename a number of sysfs attr arrays to make their function clearer
* Move the pwm#_auto_channels_temp attribute from the common to all
  models fan attr array to the per model auto mode pwm attr arrays, so
  that all the auto mode pwm attr are grouped together, and thus can be
  left out on models where we don't support auto pwm mode
* Put fan_beep attr in their own array, so that only auto mode pwm attr
  remain in the per model pwm sysfs attr arrays.
* Put the 4th special fan input for the f8000 in its own array, so that only
  auto mode pwm attr remain in the per model pwm sysfs attr arrays.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:59 +01:00
Jean Delvare
f95f0b4ce8 hwmon: (thmc50) Stop using I2C_CLIENT_MODULE_PARM
The thmc50 driver is the last user of I2C_CLIENT_MODULE_PARM, and I
would like to get rid of that macro.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Krzysztof Helt <krzysztof.h1@wp.pl>
2009-12-09 20:35:59 +01:00
Luotao Fu
93ee0a75f6 hwmon: Add Freescale MC13783 ADC driver
This driver provides support for the ADC integrated into the
Freescale MC13783 PMIC.

Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:58 +01:00
Marc Hulsman
d1ebd59a74 hwmon: (w83791d) Remove experimental dependency
The w83791d driver has been in the kernel for a while now,
time to remove the EXPERIMENTAL dependency.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:58 +01:00
Jean Delvare
52df6440a2 hwmon: Clean up detect functions
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Acked-by: "Hans J. Koch" <hjk@linutronix.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
2009-12-09 20:35:57 +01:00
Jean Delvare
a1fa4cdcc4 hwmon: (w83l785ts) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:56 +01:00
Jean Delvare
2de1875a58 hwmon: (w83792d) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:56 +01:00
Jean Delvare
3f8b845940 hwmon: (w83791d) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
2009-12-09 20:35:55 +01:00
Jean Delvare
bab2bf44f8 hwmon: (w83781d) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:54 +01:00
Jean Delvare
dbe73c8f45 hwmon: (tmp401/tmp421) Clean up detect functions
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Andre Prendel <andre.prendel@gmx.de>
2009-12-09 20:35:54 +01:00
Jean Delvare
8f2fa77c53 hwmon: (lm90) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:53 +01:00
Jean Delvare
d42a2eb5ad hwmon: (lm85) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:53 +01:00
Jean Delvare
b57dc3940a hwmon: (lm83) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:52 +01:00
Jean Delvare
747d9bedc3 hwmon: (lm77) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:52 +01:00
Jean Delvare
9560672369 hwmon: (adm1025) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:51 +01:00
Jean Delvare
8007ea35ef hwmon: (adm1021) Clean up detect function
As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:51 +01:00
Adrien Demarez
4e233cbed2 hwmon: New driver for the National Semiconductor LM73
The National Semiconductor LM73 is a single temperature sensor, much
like the famous LM75.

Signed-off-by: Adrien Demarez <adrien.demarez@bolloretelecom.eu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:50 +01:00
Jean Delvare
b72656dbc4 hwmon: (w83627hf) Stop using globals for I/O port numbers
Stop using global variables REG and VAL for I/O port numbers. This is
ugly and unsafe.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
2009-12-09 20:35:49 +01:00
Jean Delvare
8918023d40 hwmon: (w83627hf) Drop the force_addr module parameter
This module parameter is there to workaround broken BIOS. I'm not even
sure if it was used in the past 5 years, and it gets in the way of
converting the driver to the MFD infrastructure. So tell the users how
they can do the same from user-space.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
2009-12-09 20:35:48 +01:00
Jean Delvare
591ec6509e hwmon: (it87) Check for fan2 and fan3 availability
The fan2 and fan3 input and output pins can be used as GPIOs. Check
their function before exposing their sysfs attributes and accessing
their registers.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:48 +01:00
Jean Delvare
895ff26768 hwmon: (it87) Verify the VID pin usage
The VID input pins can alternatively be used as GPIOs. Make sure we
have at least 4 pins used for VID, otherwise don't bother reading and
exposing VID.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Adam Nielsen <a.nielsen@shikadi.net>
2009-12-09 20:35:47 +01:00
Ben Dooks
6d905e67cf hwmon: (s3c-hwmon) Fix build error
The previous patch, commit be4c23c93c was
from the wrong tree and thus broke the current build which had the
channel configuration name changed.

Fix the following build errors:

drivers/hwmon/s3c-hwmon.c: In function 's3c_hwmon_probe':
drivers/hwmon/s3c-hwmon.c:326: warning: initialization from incompatible pointer type
drivers/hwmon/s3c-hwmon.c:331: error: dereferencing pointer to incomplete type
drivers/hwmon/s3c-hwmon.c:336: error: dereferencing pointer to incomplete type

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-09 20:35:45 +01:00
Jiri Kosina
d014d04386 Merge branch 'for-next' into for-linus
Conflicts:

	kernel/irq/chip.c
2009-12-07 18:36:35 +01:00
André Goddard Rosa
af901ca181 tree-wide: fix assorted typos all over the place
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:55 +01:00
Jean Delvare
84d2a314bb hwmon: (adt7475) Fix sysfs file names
The adt7475 driver creates pwm#_auto_channel_temp attributes instead
of the standard pwm#_auto_channels_temp. Fix it.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
2009-11-16 12:45:40 +01:00
Jean Delvare
56e35eeebe hwmon: (adt7475) Cache limits for 60 seconds
The comment says that limits are cached for 60 seconds but the code
actually caches them for only 2 seconds. Align the code on the
comment, as 60 seconds makes more sense.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
2009-11-16 12:45:40 +01:00
Jean Delvare
cf312e0776 hwmon: (adt7475) Fix temperature fault flags
The logic of temperature fault flags is wrong, it shows faults when
there are none and vice versa. Fix it.

I can't believe this has been broken since the driver was added, 8
months ago, basically breaking temp1 and temp3, and nobody ever
complained.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
2009-11-16 12:45:39 +01:00
Ben Dooks
be4c23c93c hwmon: (s3c-hwmon) Ignore invalid divider settings
Avoid registering channels that have zero divider settings in them, as this
will only lead to kernel OOPS from divide-by-zero when the sysfs entry is
read.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-11-16 12:45:39 +01:00
Linus Torvalds
e281e315f4 Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (it87) Fix VID reading on IT8718F/IT8720F
  hwmon: (dme1737) No vid attributes for SCH311x
  hwmon: (fschmd) Fix check on unsigned in watchdog_write()
  hwmon: (coretemp) Maintainer update
2009-10-29 08:14:58 -07:00
Ian E. Morgan
2545f038f4 lis3: add support for the HP HDX 18
I have an HP HDX 18 laptop, and noted that the configuration of the
accelerometer needs to be x_inverted.

Signed-off-by: Ian E. Morgan <penguin.wrangler@gmail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-29 07:39:32 -07:00
Éric Piel
af19611c4d lis3: add support for the HP EliteBook 8530w
Correct orientation for  HP EliteBook 8530w.

Reported-by: Jörgen Jonssson <jorgen.jonsson@saitek.se>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-29 07:39:32 -07:00
Pavel Herrmann
a03018ff71 lis3: better support for hp 6730x
I have learned that the 6730b and 6730s have different accelerometer
orientation, and have modified the driver accordingly (diff attached),
while dropping the wild guess for AMD based 6735 having the same
orientation as Intel based 6730 (this is not true for any other related
series/family, thus is not probable for 673x).

Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-29 07:39:32 -07:00
Jean Delvare
371dc4a6d8 hwmon: (it87) Fix VID reading on IT8718F/IT8720F
Comparing apples to bananas doesn't seem right. Consistently use the
chips enum for chip type comparisons, to avoid such bugs in the
future.

The bug has been there since support for the IT8718F was added, so
VID never worked for this chip nor for the similar IT8720F.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-10-24 13:28:47 +02:00
Jean Delvare
9d0914468f hwmon: (dme1737) No vid attributes for SCH311x
The SCH311x chips do not have VID inputs, so the cpu0_vid and vrm
attributes shouldn't be created for them.

This fixes lm-sensors ticket #2353:
http://www.lm-sensors.org/ticket/2353

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Udo van den Heuvel <udovdh@xs4all.nl>
Cc: Juerg Haefliger <juergh@gmail.com>
2009-10-24 13:28:46 +02:00
Roel Kluin
c7702c3134 hwmon: (fschmd) Fix check on unsigned in watchdog_write()
If unsigned the watchdog_trigger() return value will not be
checked correctly.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-10-24 13:28:45 +02:00
Linus Torvalds
4c274fff4f Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (s3c-hwmon) Disable build for S3C64xx
  MAINTAINERS: Fix Riku Voipio's address
  hwmon: (asus_atk0110) Enable the EC
  hwmon: (asus_atk0110) Refactor the code
  hwmon: (sht15) Fix spurious section mismatch warning
2009-10-11 11:23:33 -07:00
Alexey Dobriyan
d43c36dc6b headers: remove sched.h from interrupt.h
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
2009-10-11 11:20:58 -07:00
Mark Brown
384e724b6b hwmon: (s3c-hwmon) Disable build for S3C64xx
The s3c-hwmon driver depends on the arch/arm implementation of the core
ADC support for the chip.  Since the S3C64xx version has not yet been
merged disable building of the driver on S3C64xx for now.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-10-09 20:35:21 +02:00
Luca Tettamanti
9e6eba610c hwmon: (asus_atk0110) Enable the EC
On newer ASUS boards (e.g. P7P55D) the EC (that - among other things - is
responsible for updating the readings from the hwmon sensors) is disabled
by default since ASUS detected conflict with some tools under Windows.
The following patch checks the state of the EC and enable it if needed;
under Linux, native drivers are locked out from ACPI owned resources so
there's no risk of conflict.

Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Robert Hancock <hancockrwd@gmail.com>
Tested-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-10-09 20:35:18 +02:00
Luca Tettamanti
18e2555585 hwmon: (asus_atk0110) Refactor the code
Refactor the code of the new style interface around GGRP (enumeration) and
GITM (read) helpers to mimic ASL code. Also switch the read path to use
dynamic buffers (handled by ACPI core) since ASUS expanded the return buffer
(ASBF) in newer boards (e.g. P7P55D).

Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Robert Hancock <hancockrwd@gmail.com>
Tested-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-10-09 20:35:18 +02:00
Rakib Mullick
cb0f1a1e77 hwmon: (sht15) Fix spurious section mismatch warning
Fix spurious section mismatch warnings, caused due to reference from
variable sht_drivers to
 __devinit/__devexit functions sht15_probe()/remove().

 We were warned by the following warnings:

  LD      drivers/hwmon/built-in.o
WARNING: drivers/hwmon/built-in.o(.data+0x264a0): Section mismatch in
reference from the variable sht_drivers to the function
.devinit.text:sht15_probe()
The variable sht_drivers references
the function __devinit sht15_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: drivers/hwmon/built-in.o(.data+0x264a4): Section mismatch in
reference from the variable sht_drivers to the function
.devexit.text:sht15_remove()
The variable sht_drivers references
the function __devexit sht15_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: drivers/hwmon/built-in.o(.data+0x264f0): Section mismatch in
reference from the variable sht_drivers to the function
.devinit.text:sht15_probe()
The variable sht_drivers references
the function __devinit sht15_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: drivers/hwmon/built-in.o(.data+0x264f4): Section mismatch in
reference from the variable sht_drivers to the function
.devexit.text:sht15_remove()
The variable sht_drivers references
the function __devexit sht15_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: drivers/hwmon/built-in.o(.data+0x26540): Section mismatch in
reference from the variable sht_drivers to the function
.devinit.text:sht15_probe()
The variable sht_drivers references
the function __devinit sht15_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: drivers/hwmon/built-in.o(.data+0x26544): Section mismatch in
reference from the variable sht_drivers to the function
.devexit.text:sht15_remove()
The variable sht_drivers references
the function __devexit sht15_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: drivers/hwmon/built-in.o(.data+0x26590): Section mismatch in
reference from the variable sht_drivers to the function
.devinit.text:sht15_probe()
The variable sht_drivers references
the function __devinit sht15_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-10-09 20:35:17 +02:00
Samu Onkalo
d82e23dcae lis3lv02d_spi: module unload didn't remove sysfs entry
In module unload, lis3lv02d core driver sysfs clean up was not called.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: "Trisal, Kalhan" <kalhan.trisal@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-08 07:36:40 -07:00
Jean Delvare
2d2a7cff1b ltc4215/ltc4245: Discard obsolete detect methods
There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.

So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
2009-10-04 22:53:42 +02:00
Alexey Dobriyan
828c09509b const: constify remaining file_operations
[akpm@linux-foundation.org: fix KVM]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:11 -07:00
Linus Torvalds
3e56d49390 Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (ltc4245) Clear faults at startup
  hwmon: (ltc4215) Clear faults at startup
  hwmon: (coretemp) Add Lynnfield CPU
  hwmon: (coretemp) Add support for Penryn mobile CPUs
  hwmon: (coretemp) Fix Atom CPUs support
  hwmon: Delete deprecated FSC drivers
  hwmon: (adm1031) Add sysfs files for temperature offsets
2009-09-23 15:20:16 -07:00
Ira W. Snyder
58f055e531 hwmon: (ltc4245) Clear faults at startup
When power is applied to the ltc4245 chip it sometimes reports spurious
faults, which are exposed as alarms in the hwmon output. Clear the fault
register when the driver is installed to clear the alarms.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-23 22:59:44 +02:00
Ira W. Snyder
b6b9d69602 hwmon: (ltc4215) Clear faults at startup
When power is applied to the ltc4215 chip it sometimes reports spurious
faults. The faults are not yet exposed via sysfs, however it may be useful
for userspace to read the fault register directly with the i2cget command.
Clear the fault register when the driver is installed so userspace doesn't
have to worry about spurious fault indications.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-23 22:59:43 +02:00
Huaxu Wan
fa08acd7d1 hwmon: (coretemp) Add Lynnfield CPU
Add Lynnfield processor support. Lynnfield is a quad-core Nehalem
based microprocessor for Desktop market, which is introduced in
September 2009.

Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Kent Liu <kent.liu@linux.intel.com>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-23 22:59:43 +02:00
Rudolf Marek
eccfed4221 hwmon: (coretemp) Add support for Penryn mobile CPUs
Following patch adds support for mobile Penryn CPUs. Intel documents this
poorly. I asked the Coretemp author for some help. This is totally untested and
may not work. Please test!

Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-23 22:59:42 +02:00
Rudolf Marek
708a62bcd5 hwmon: (coretemp) Fix Atom CPUs support
Fix Atom CPUs support. Intel documents TjMax at 90 degrees C but
some Atoms may have 125 degrees C (this is undocumented speculation).

Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-23 22:59:42 +02:00
Jean Delvare
91f17e02a2 hwmon: Delete deprecated FSC drivers
The legacy fscpos and fscher drivers have been replaced by the unified
fschmd driver. The transition period is over now, we can delete them.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2009-09-23 22:59:42 +02:00
Ira Snyder
49dc9efed0 hwmon: (adm1031) Add sysfs files for temperature offsets
The ADM1030/ADM1031 chips have temperature offset registers, for both the
local and remote temperature sensors. Following the example set forth in
the LM90/ADM1032 driver, expose the offset registers to userspace.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-23 22:59:41 +02:00
Anton Vorontsov
e0626e3844 spi: prefix modalias with "spi:"
This makes it consistent with other buses (platform, i2c, vio, ...).  I'm
not sure why we use the prefixes, but there must be a reason.

This was easy enough to do it, and I did it.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:43 -07:00
Anton Vorontsov
8cec03eee4 hwmon: lm70: convert to device table matching
Make the code a little bit nicer, and shorter.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:43 -07:00
Anton Vorontsov
d2a5c10f80 hwmon: adxx: convert to device table matching
Make the code a little bit nicer, and shorter.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:43 -07:00
Roel Kluin
912e837aef dme1737: Keep index within pwm_config[]
The static code scanner "Parfait" reported this because pwm_config is
only 3 bytes - pwm_config[3] is out of range.

Since this code path is never called with ix == 3 (the device has no PWM4
output) this doesn't change anything in practice.  But to encourage
testing with Parfait, lets make the warning go away...

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:28 -07:00
Henrik Rydberg
a976f150a6 hwmon: applesmc: restore accelerometer and keyboard backlight on resume
On resume from suspend, the driver currently resets the logical state as
if it was brought up from halt.  This patch uses the
dev_pm_ops.resume/restore methods to synchronize the hardware with the
memorized logical state, in effect bringing back the accelerometer and
backlight to the state prior to suspend.  Works for both suspend to ram
and hibernation.  The patch has zero effect on the running state.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:49 -07:00
Roel Kluin
560a64a2b5 hwmon: fix freeing of gpio_data and irq
If already requested, gpio_data and irq should be freed in the case of an
error.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:49 -07:00
Michael Abbott
905ffdc35e drivers/hwmon/adm1021.c: add low_power support for adm1021 driver
Occasionally it is helpful to be able to turn a temperature sensor off
(for example if it's making unwanted electrical noise).  This patch
adds a sysfs node to put any adm1021 compatible device into low power mode.

Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:49 -07:00
Michael Abbott
f266889517 drivers/hwmon/adm1021.c: support high precision ADM1023 remote sensor
The ADM1023 temperature sensor supports higher resolution for its external
sensor (sensitivity of 1/8 deg C).  This patch makes this higher
resolution available through the appropriate temperature sysfs nodes.

Curiously, this functionality was available in the 2.4 kernel driver (but
formatted in a less helpful manner).

Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:49 -07:00
Daniel Mack
dc791f8aee lis3_spi: code cleanups
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:49 -07:00
Daniel Mack
2cd9645e2f lis3: add power management functions
This enabled power management functions for the SPI transport layer of the
lis3 devices.  The device's suspend mode is only entered in case no wakeup
threshold has been given.  In this case, the device is supposed to wake up
the system and must thus not be put to deep sleep.

[randy.dunlap@oracle.com: fix lis3-spi for CONFIG_PM=n]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:49 -07:00
Daniel Mack
8873c33483 lis3: add free-fall/wakeup function via platform_data
This offers a way for platforms to define flags and thresholds for the
free-fall/wakeup functions of the lis302d chips.

More registers needed to be seperated as they are specific to the

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:48 -07:00
Michael Riepe
0bf41d9f41 drivers/hwmon/coretemp.c: enable the Intel Atom
Enable the coretemp driver on an Intel Atom.

I'm not sure if the readings are correct, however - on my 330, the driver
reports values between 27 and 41 °C (with core1 being about 8°C hotter
than core0, given the same load).  Maybe the maximum temperature of 100 °C
is wrong for Atom CPUs.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:48 -07:00
Linus Torvalds
6f130478e2 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (55 commits)
  regulator: Voltage count for AB3100
  mfd: Convert WM8350 to use request_threaded_irq()
  mfd: Update MAINTAINERS patterns for WM831x
  mfd: Fix twl4030-power warnings
  regulator: AB3100 support
  rtc: AB3100 RTC support
  mfd: Fix ab3100-otp build failure
  mfd: OMAP: Board-specifc twl4030 DPS scripts for RX51 board
  mfd: Print warning for twl4030 out-of-order script loading
  mfd: Add support for TWL4030/5030 dynamic power switching
  mfd: AB3100 OTP readout
  regulator: Add Freescale MC13783 driver
  mfd: Add Freescale MC13783 driver
  mfd: AB3100 disable irq nosync
  mfd: AB3100 alter default setting
  mfd: AB3100 propagate error
  mfd: AB3100 accessor function cleanups
  rtc: Add support for RTCs on Wolfson WM831x devices
  regulator: get pcap data from the parent device
  input: PCAP2 misc input driver
  ...
2009-09-18 09:22:36 -07:00
Mark Brown
08bad5a821 hwmon: WM831x PMIC hardware monitoring driver
This driver adds support for the hardware monitoring features of
the WM831x PMICs to the hwmon API. Monitoring is provided for
the system voltages supported natively by the WM831x, the chip
temperature, the battery temperature and the auxiliary inputs
of the WM831x.

Currently no alarms are supported, though digital comparators on
the WM831x devices would allow these to be provided.

Since the auxiliary and battery temperature input scaling depends
on the system configuration the value is reported as a voltage to
userspace.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-09-17 09:47:02 +02:00
Mark Brown
fb6c023a2b hwmon: Add WM835x PMIC hardware monitoring driver
This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-09-17 09:46:51 +02:00
Jean Delvare
5cfaf33813 hwmon: (lm85) Don't bind to Winbond/Nuvoton WPCD377I
The Winbond/Nuvoton WPCD377I is the reduced version of a Super-I/O
which emulates the National Semiconductor LM96000 hardware monitoring
chips, but without the hardware monitoring part. Instead of plain
disabling the emulation, the vendor left the emulated chip visible,
but all monitored values are always zero. This is rather confusing for
the users. So detect this case and refuse to bind to such fake chips.

This fixes lm-sensors ticket #2182:
http://www.lm-sensors.org/ticket/2182

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-15 17:18:14 +02:00
Jean Delvare
61cba5c244 hwmon: Clearly mark ACPI drivers as such
Now that we have ACPI-based hardware monitoring drivers, and we will
start telling users to use them instead of native drivers when I/O
resources conflict, I think it would be good to clearly mark ACPI
drivers as such in Kconfig.

Also, in the case of monolithic kernels, I think the ACPI drivers
should take precedence over native drivers, so they should be listed
first in Makefile.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Luca Tettamanti <kronos.it@gmail.com>
2009-09-15 17:18:13 +02:00
Julia Lawall
86855b0c1f hwmon: Use resource_size
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct resource *res;
@@

- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-15 17:18:13 +02:00
H Hartley Sweeten
6055fae8ac hwmon: Include <linux/io.h> instead of <asm/io.h>
Drivers should be including <linux/io.h> instead of <asm/io.h>.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Frank Seidel <frank@f-seidel.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-15 17:18:13 +02:00
Andre Prendel
9410700b88 hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips
Add support for Texas Instruments TMP421/422/423 temperature sensor IC.

TI's TMP421/422/423 are I2C temperature sensor chips. These chips are
similar to TI's TMP401/411 chips, but with reduced functionality (only
temperature measurement). The chips have one local sensor and up to
three (TMP423) remote sensors.

Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-15 17:18:11 +02:00
Jean Delvare
5bed13f580 hwmon-vid: Ignore 6th VID pin of AMD family 0Fh processors
We had a report about a mainboard for AMD family 0Fh processors not
routing the 6th VID pin from the CPU to the hardware monitoring chip.

While the vendor should have wired the pin (or, failing that, should
have hardwired it to level high rather than low), the fact is that
none of these processors are currently known to operate at the lower
voltage levels which require the 6th VID pin. So, as a practical
workaround, I propose to ignore the 6th VID pin for these CPUs.

If this decision ever causes problems, we'll reconsider.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Frank Myhr <fmyhr@fhmtech.com>
Tested-by: Hleb Valoshka <375gnu@gmail.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
2009-09-15 17:18:11 +02:00
Alistair John Strachan
bbe5939ab1 hwmon: (abituguru3) Support multiple DMI strings per chip ID
Most known Abit motherboards have unique uguru chip IDs. However,
some "refresh" boards keep the same chip ID but have a different
DMI string. As our DMI board string matching is (necessarily)
strict, some boards were failing DMI detection, and as the old
probe method was also failing, the driver would not load.

The only known boards affected by this problem are the IP35 Pro XE
(vs IP35 Pro) and the AB9 Pro (vs AB9). Is it not sufficient to
relax the match criteria, as some boards (e.g. the AB9 Quad GT)
have different uguru chip IDs.

This patch replaces the dmi_name string with a NULL terminated
array of strings to be matched per uguru chip ID. It has been
compile and runtime tested (thanks Rune).

References: https://bugs.launchpad.net/bugs/298798

Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Rune Svendsen <runesvend@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-15 17:18:10 +02:00
Ben Dooks
63c949ea1d Merge branch 'next-s3c-hwmon' into next-s3c 2009-08-14 15:23:15 +01:00
Luca Tettamanti
8d282497cb hwmon: (asus_atk0110) Fix upper limit readings
On newer Asus boards the "upper" limit of a sensor is encoded as
delta from the "lower" limit. Fix the driver to correctly handle
this case.

Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Tested-by: Alex Macfarlane Smith <nospam@archifishal.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-07-28 16:31:39 +02:00
Jean Delvare
1b54ab450b hwmon: (smsc47m1) Differentiate between LPC47M233 and LPC47M292
The SMSC LPC47M233 and LPC47M292 chips have the same device ID but
are not compatible.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2009-07-28 16:31:39 +02:00
Ben Dooks
bff78650a2 ARM: HWMON: S3C24XX series ADC driver
Add support for the ADC controller on the S3C series of processors to
drivers/hwmon for use with hardware monitoring systems.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-07-18 10:15:54 +01:00
Alistair John Strachan
ec05a8d75d hwmon: (abituguru3) DMI probing for AB9, AB9 QuadQT and IX38 QuadGT
Switch the AB9, AB9 QuadQT and IX38 QuadGT over from port
probing to the preferred DMI probe method.

Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: dan <dan@deeog.com>
Tested-by: Nygel Lyndley <nygel.lyndley@gmail.com>
Tested-by: Dmitriy Fedchenko <dmitriy-fedc@yandex.ru>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-07-11 13:42:38 +02:00
Joe Perches
24205e0850 hwmon: (sht15) Remove unnecessary semicolon
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-07-11 13:42:37 +02:00
Jiri Slaby
025dc740d0 hwmon: (max6650) Fix lock imbalance
Add omitted update_lock to one switch/case in set_div.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-07-11 13:42:37 +02:00
Linus Torvalds
517d08699b Merge branch 'akpm'
* akpm: (182 commits)
  fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
  fbdev: *bfin*: fix __dev{init,exit} markings
  fbdev: *bfin*: drop unnecessary calls to memset
  fbdev: bfin-t350mcqb-fb: drop unused local variables
  fbdev: blackfin has __raw I/O accessors, so use them in fb.h
  fbdev: s1d13xxxfb: add accelerated bitblt functions
  tcx: use standard fields for framebuffer physical address and length
  fbdev: add support for handoff from firmware to hw framebuffers
  intelfb: fix a bug when changing video timing
  fbdev: use framebuffer_release() for freeing fb_info structures
  radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
  s3c-fb: CPUFREQ frequency scaling support
  s3c-fb: fix resource releasing on error during probing
  carminefb: fix possible access beyond end of carmine_modedb[]
  acornfb: remove fb_mmap function
  mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
  mb862xxfb: restrict compliation of platform driver to PPC
  Samsung SoC Framebuffer driver: add Alpha Channel support
  atmel-lcdc: fix pixclock upper bound detection
  offb: use framebuffer_alloc() to allocate fb_info struct
  ...

Manually fix up conflicts due to kmemcheck in mm/slab.c
2009-06-16 19:50:13 -07:00
Daniel Mack
8f3128e714 lis3: add click function
The LIS302DL accelerometer chip has a 'click' feature which can be used to
detect sudden motion on any of the three axis.  Configuration data is
passed via spi platform_data and no action is taken if that's not
specified, so it won't harm any existing platform.

To make the configuration effective, the IRQ lines need to be set up
appropriately.  This patch also adds a way to do that from board support
code.

The DD_* definitions were factored out to an own enum because they are
specific to LIS3LV02D devices.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16 19:47:57 -07:00
Eric Piel
0093716e6d lis3: add three new laptop models
Separate the 6710 and 6715, and set the right axis information for the
6715.
Reported-by: Isaac702 <isaac702@gmail.com>

Add the 6930.
Reported-by: Christian Weidle <slateroni@gmail.com>

Add the 2710.
Reported-by: Pavel Herrmann <morpheus.ibis@gmail.com>

Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16 19:47:57 -07:00
Eric Piel
dc6ea97bac lis3: use input_polled_device
Now that there is no need to hookup on the open/close of the joystick,
it's possible to use the simplified interface input_polled_device, instead
of creating our own kthread.

[randy.dunlap@oracle.com: fix Kconfig]
[randy.dunlap@oracle.com: fix Kconfig some more]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16 19:47:57 -07:00
Eric Piel
a002ee896d lis3: remove automatic shutdown of the device
After measurement on my laptop, it seems that turning off the device does
not bring any energy saving (within 0.1W precision).  So let's keep the
device always on.  It simplifies the code, and it avoids the problem of
reading a wrong value sometimes just after turning the device on.

Moreover, since commit ef2cfc790b had been
too zealous, the device was actually never turned off anyway.  This patch
also restores the damages done by this commit concerning the
initialisation/poweroff.

Also do more clean up with the usage of the lis3_dev global variable.

Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16 19:47:57 -07:00
Eric Piel
c28842421c lis3: fix misc device unregistering and printk
Can only unregister the misc device if it was registered before.  Also
remove debugging messages, which in addition were not properly formated.

Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16 19:47:56 -07:00
Christian Engelmayer
52b5226f48 hwmon: (max6650) Add support for alarms
Export the alarm flags provided by the MAX6650/MAX6651 fan-speed regulator
and monitor chips via sysfs.

Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:52 +02:00
Hans de Goede
09475d32e6 hwmon: (f71882fg) Add support for the F71858F
Add support for the hwmon part of the Fintek F71858FG superio IC to the
f71882fg driver. Many thanks to Jelle de Jong for lending me a motherboard 
with this superio on it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:52 +02:00
Hans de Goede
b6858bca8d hwmon: (f71882fg) Add temp#_fault sysfs attr for f8000
While working on f71852fg support I noticed that the f8000 sysfs attr
table was missing entries for temp#_fault, which the f8000 does have and
which we were already reading.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:51 +02:00
Hans de Goede
996cadb2bf hwmon: (f71882fg) Sanity check f8000 pwm settings
We depend up on the pwm_enable register (0x96) not containing any reserved
settings in various places. We were already checking to make sure there
were no reserved settings in the register for the f71862fg, this patch adds
the same checking for the f8000, while at it it also moves the code to
a more apropriate place so we don't need to check if the fan/pwm part
of the IC is enabled twice.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:51 +02:00
Hans de Goede
3fc7838a20 hwmon: (f71882fg) Cleanup f8000 pwm handling
Currently we are using separate per model sysfs attr for the 3th pwm, because
the 3th pwm of the f8000 only has automatic mode and not manual mode. Doing
things this way was getting in the way for adding f71858fg support, so this
patch makes the pwm attr identical for all models, and instead adds a check
to store_pwm_enable() disallowing setting the 3th pwm to manual mode
on a f8000 IC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:50 +02:00
Jean Delvare
2958b1ec6b hwmon: PCI quirk for hwmon access on MSI MS-7031 board
The MSI MS-7031 is based on an ATI IXP300 south bridge. On this south
bridge, accessible I/O ports must be enabled explicitly. Unfortunately
the BIOS forgets to enable access to the hardware monitoring chip I/O
ports, so hardware monitoring fails.

Add a quirk enabling access to the required ports (0x295-0x296). This
is exactly what MSI's own hardware monitoring application is doing, so
it has to be the right way.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:50 +02:00
Jean Delvare
c1e48dce05 hwmon: (w83627ehf) Add W83627DHG-P support
Add support for the new incarnation of the Winbond/Nuvoton W83627DHG
chip known as W83627DHG-P. It is basically the same as the original
W83627DHG with an additional automatic can speed control mode (not
supported by the driver yet.)

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Madhu <madhu.chinakonda@gmail.com>
2009-06-15 18:39:50 +02:00
Andre Prendel
fce0758f59 hwmon: (tmp401) Add support for TI's TMP411 sensors chip
This adds support for TI's TMP411 sensor chip.

Preliminary support were done by Gabriel Konat, Sander Leget and
Wouter Willems. The chip is compatible with TI's TMP401 sensor
chip. It has additional support for historical minimun/maximum
measurements.

Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:47 +02:00
Hans de Goede
ab2b79d5e2 hwmon: (tmp401) Add support for TI's TMP401 sensor chip
This is a new hwmon driver for TI's TMP401 temperature sensor IC. This driver
was written on behalf of an embedded systems vendor under the
Linux driver project.

It has been tested using a TI TMP401 sample attached to a i2c-tiny-usb adapter.
Which was provided by Till Harbaum, many thanks to him for this!

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:46 +02:00
Darrick J. Wong
8070408b54 hwmon: (ibmaem) Automatically load on HC10 blade
Enable auto-probing for the HC10 blade and amend the supported system
list.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:39:46 +02:00
Jean Delvare
cd659fd0d7 hwmon: Fix more __devexit_p glitches
Make sure __devexit and devexit_p() match in all hwmon drivers.
Suggested by a similar fix from Mike Frysinger.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
2009-06-15 18:39:45 +02:00
Mike Frysinger
39d8bbedb9 hwmon: (lm78) Add missing __devexit_p()
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-01 13:46:49 +02:00
Jean Delvare
848ddf116b hwmon: (w83781d) Fix W83782D support (NULL pointer dereference)
Commit 360782dde0 (hwmon: (w83781d) Stop
abusing struct i2c_client for ISA devices) broke W83782D support for
devices connected on the ISA bus. You will hit a NULL pointer
dereference as soon as you read any device attribute. Other devices,
and W83782D devices on the SMBus, aren't affected.

Reported-by: Michel Abraham
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Abraham
2009-05-08 20:27:28 +02:00
Luca Tettamanti
b9008708f2 hwmon: (asus_atk0110) Fix compiler warning
atk_sensor_type is only used when DEBUG is defined.

Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-05-08 20:27:28 +02:00
Jonathan Cameron
251eb40f5c hwmon: sht15 humidity sensor driver
Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf

These sensors communicate over a 2 wire bus running a device specific
protocol.  The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available.  This is handled by
an interrupt that is disabled under all other conditions.

I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!

Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem.  If not it should be provided in the
platform data.

I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-13 15:04:29 -07:00
Huang Weiyi
2f6f6c6b5c hp_accel: remove unused #include <version.h>
Remove unused #include <version.h> in drivers/hwmon/hp_accel.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-13 15:04:28 -07:00
Linus Torvalds
10a0d91289 Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: Add Asus ATK0110 support
  hwmon: (lm95241) Convert to new-style i2c driver
2009-04-07 08:44:43 -07:00
Herbert Valerio Riedel
3bcfa9e47a hwmon: add support for GMT G760A fan speed PWM controller
This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.

Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Matthew Palmer <mpalmer@debian.org>
Signed-off-by: Laurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:03 -07:00
Luca Tettamanti
2c03d07ad5 hwmon: Add Asus ATK0110 support
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.

There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).

Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.

Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-04-07 15:32:59 +02:00
Jean Delvare
797eaa4b02 hwmon: (lm95241) Convert to new-style i2c driver
The legacy i2c binding model is going away really soon now, so convert
the lm95241 driver to the new binding model or it will break.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
2009-04-07 15:32:59 +02:00
Linus Torvalds
811158b147 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
  trivial: Update my email address
  trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
  trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
  trivial: Fix misspelling of "Celsius".
  trivial: remove unused variable 'path' in alloc_file()
  trivial: fix a pdlfush -> pdflush typo in comment
  trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
  trivial: wusb: Storage class should be before const qualifier
  trivial: drivers/char/bsr.c: Storage class should be before const qualifier
  trivial: h8300: Storage class should be before const qualifier
  trivial: fix where cgroup documentation is not correctly referred to
  trivial: Give the right path in Documentation example
  trivial: MTD: remove EOL from MODULE_DESCRIPTION
  trivial: Fix typo in bio_split()'s documentation
  trivial: PWM: fix of #endif comment
  trivial: fix typos/grammar errors in Kconfig texts
  trivial: Fix misspelling of firmware
  trivial: cgroups: documentation typo and spelling corrections
  trivial: Update contact info for Jochen Hein
  trivial: fix typo "resgister" -> "register"
  ...
2009-04-03 15:24:35 -07:00
Daniel Mack
bb233fdfc7 lis3: SPI transport layer
Make use of the new abstraction layer and add a new transport layer for
spi.  Works fine on a PXA based board.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:22 -07:00
Daniel Mack
a38da2ed74 lis3: solve dependency between core and ACPI
This solves the dependency between lis3lv02d.[ch] and ACPI specific
methods.  It introduces a ->bus_priv pointer to the device struct which is
casted to 'struct acpi_device' in the ACIP layer.  Changed hp_accel.c
accordingly.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:22 -07:00
Daniel Mack
ab337a6327 lis3: reorder functions to make forward decl obsolete
Move lis3lv02d_init_device() down so that the forward declaration of
lis3lv02d_add_fs() becomes unnecessary.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:22 -07:00
Luca Cappa
12a324b6a3 hp_accel: axis conversion for hp compaq 8710w
I have a laptop HP Compaq 8710W, I compiled into my kernel the LIS3LV02DL
and HP_ACCEL module drivers.  While loading it cannot recognize the laptop
model, so i am sending the necessary information to update the database of
axis orientations.

>When the laptop is horizontal the position reported is about 0 for X and Y
>and a positive value for Z
Yes, it is about 0,0,1000, the actual reading says: (-17,-26,1018);

> If the left side is elevated, X increases (becomes positive)
Yes, X goes toward to positive 1000.

>If the front side (where the touchpad is) is elevated, Y decreases (becomes negative)
No, Y goes toward to positive 1000.

>If the laptop is put upside-down, Z becomes negative
Yes, the laptop on a table Z gives 1000, and if upsidedown the Z reads
-1000.

So in few words the Y axis is inverted.

Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:21 -07:00
Pavel Machek
9d7639d33a hp_accel: add two more axis information
Add two more laptops to whitelist.

Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:21 -07:00
Ira Snyder
72f5de92e1 hwmon: Add LTC4215 driver
Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.

I have tested the driver with my board, and it appears to work fine.  With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power.  With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power.  I'm not drawing any current at the
moment, so this is reasonable.  The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.

I didn't attempt to support changing any of the chip's settings or
enabling the FET.  I'm not sure even how to do that and still fit within
the hwmon framework.  :)

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:21 -07:00
Davide Rizzo
0616032758 hwmon: LM95241 driver
An hwmon driver for the National Semiconductor LM95241 triple temperature
sensors chip

Signed-off-by: Davide Rizzo <elpa-rizzo@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:21 -07:00
Pavel Machek
be84cfc588 hp_accel: adev is poor name of exported symbol
As Andrew noted, adev is pretty poor name for symbol being exported.
Rename it to lis3.

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Cc: <Quoc.Pham@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-01 08:59:21 -07:00
Hans de Goede
de15f093e6 hwmon: (fschmd) Add support for the FSC Hades IC
Add support for the Hades to the FSC hwmon driver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-30 21:46:45 +02:00
Hans de Goede
c69ab2b78e hwmon: (fschmd) Add support for the FSC Syleus IC
Many thanks to Fujitsu Siemens Computers for providing docs and a
machine to test the driver on.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-30 21:46:45 +02:00
Jean Delvare
e7a19c5624 dmi: Let dmi_walk() users pass private data
At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>
2009-03-30 21:46:44 +02:00
Jean Delvare
fb4504fe84 Move the pcf8591 driver to hwmon
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.

If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
2009-03-30 21:46:43 +02:00
Gong Jun
a157d06d4d hwmon: (w83627ehf) Only expose in6 or temp3 on the W83667HG
The pin for in6 and temp3 is shared on the W83667HG, so only one of
these features can be supported on any given system. Let the driver
select which one depending on the temp3 disabled bit.

Signed-off-by: Gong Jun <JGong@nuvoton.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-30 21:46:43 +02:00
Gong Jun
237c8d2f54 hwmon: (w83627ehf) Add support for W83667HG
Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.

At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.

Signed-off-by: Gong Jun <JGong@nuvoton.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-30 21:46:42 +02:00
Jean Delvare
1704b26ee3 hwmon: (w83627ehf) Invert fan pin variables logic
Use positive logic for fan pin variables (variable is set if pin is
used for fan), instead of negative logic which is error prone.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Gong Jun <JGong@nuvoton.com>
2009-03-30 21:46:42 +02:00
Frank Seidel
b6a33fe2cc hwmon: (hdaps) Fix Thinkpad X41 axis inversion
Fix for kernel.org bug #7154: hdaps inversion of actual Thinkpad
X41's Y-axis.

Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-30 21:46:42 +02:00
Frank Seidel
2b8cf3e8c0 hwmon: (hdaps) Allow inversion of separate axis
Fix for kernel.org bug #7154: hdaps inversion of each axis. This
version is based on the work from Michael Ruoss <miruoss@student.ethz.ch>.

Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-30 21:46:41 +02:00
Jean Delvare
e4879e28ab hwmon: (ds1621) Avoid unneeded register access
Register access over SMBus isn't cheap, so avoid register access where
possible:
* Only write back the configuration register if it changed.
* Don't refresh the register cache when we don't have to.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
2009-03-30 21:46:40 +02:00
Jean Delvare
594592dc6f hwmon: (ds1621) Clean up register access
Fix a few oddities in how the ds1621 driver accesses the registers:
* We don't need a wrapper to access the configuration register.
* Check for error before calling swab16. Error checking isn't
  complete yet, but that's a start.
* Device-specific read functions should never be called during
  detection, as by definition we don't know what device we are talking
  to at that point.
* Likewise, don't assume that register reads succeed during detection.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
2009-03-30 21:46:40 +02:00
Jean Delvare
9202add674 hwmon: (ds1621) Reorder code statements
Reorder the ds1621 driver code so that we can get rid of forward
function declarations.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
2009-03-30 21:46:40 +02:00
Riku Voipio
b26e0ed493 trivial: Update my email address
Update my email address.

Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-03-30 15:22:04 +02:00
Andrew Klossner
51b3e27001 hwmon: (f75375s) Remove unnecessary and confusing initialization
f75375_probe calls i2c_get_clientdata to initialize the data pointer,
but there isn't yet any client data to get, and the value is never
used before the variable is assigned a new value seven lines later.

The call doesn't hurt anything and wastes only a couple of cycles.
The reason to fix it is because this module serves as an example to
hackers writing new hwmon drivers, and this part of the example is
confusing.

Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-12 13:36:39 +01:00
Jean Delvare
e267d25005 hwmon: (it87) Properly decode -128 degrees C temperature
The it87 driver is reporting -128 degrees C as +128 degrees C.
That's not a terribly likely temperature value but let's still
get it right, especially when it simplifies the code.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-12 13:36:39 +01:00
Darrick J. Wong
1a51e068c9 hwmon: (lm90) Document support for the MAX6648/6692 chips
Update documentation to prevent further confusion/duplication.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-03-12 13:36:38 +01:00
Jean Delvare
3bb9db7923 hwmon: (abituguru3) Fix I/O error handling
Fix a logic bug reported by Roel Kluin, by rewriting the error
handling code in a clearer way.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2009-03-12 13:36:38 +01:00
Darrick J. Wong
8ef1f0291a lm85: add VRM10 support for adt7468 chip
The adt7468 chip supports VRM10 sensors just like the adt7463; add a
missing check for it.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-10 15:55:10 -07:00
Darrick J. Wong
c15ade6578 lm85: fix the version check that broke adt7468 probing
The verstep check in the lm85 driver fails because the upper nibble of
the version register is 0x7, not 0x6, on the adt7468 chip.  Probing of
all adt7468s was broken by 69fc1feba2
("hwmon: (lm85) Rework the device detection"), and this patch fixes
that.  Also add in a missing i2c_device_id that accidentally got dropped
from the original patch.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-10 15:55:10 -07:00
Giuseppe Bilotta
9ccf3b5e84 lis3lv02d: add axes knowledge of HP Pavilion dv5 models
Add support for HP Pavilion dv5.

Since Intel-based models have an inverted x axis, while AMD-based models
have an inverted y axis, we introduce a new macro that special-cases axis
orientation based on two DMI entries: HP dv5 axis configuration is then
based on both the PRODUCT and BOARD name.

Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Cc: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Tested-by: Palatis Tseng <palatis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-18 15:37:54 -08:00
Giuseppe Bilotta
137bad3234 lis3lv02d: support both one- and two-byte sensors
Sensors responding with 0x3B to WHO_AM_I only have one data register per
direction, thus returning a signed byte from the position which is
occupied by the MSB in sensors responding with 0x3A.

Since multiple sensors share the reply to WHO_AM_I, we rename the defines
to better indicate what they identify (family of single and double
precision sensors).

We support both kind of sensors by checking for the sensor type on init
and defining appropriate data-access routines and sensor limits (for the
joystick) depending on what we find.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Acked-by: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-18 15:37:54 -08:00
Pavel Machek
ef2cfc790b hp accelerometer: add freefall detection
This adds freefall handling to hp_accel driver.  According to HP, it
should just work, without us having to set the chip up by hand.

hpfall.c is example .c program that parks the disk when accelerometer
detects free fall.  It should work; for now, it uses fixed 20seconds
protection period.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-18 15:37:54 -08:00
Hans de Goede
18632f84fa hwmon: Fix ACPI resource check error handling
This patch fixes a number of cases where things were not properly
cleaned up when acpi_check_resource_conflict() returned an error,
causing oopses such as the one reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=483208

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-02-17 19:59:54 +01:00
Jean Delvare
603eaa1bdd hwmon: (f71882fg) Hide misleading error message
If the F71882FG chip is at address 0x4e, then the probe at 0x2e will
fail with the following message in the logs:
f71882fg: Not a Fintek device

This is misleading because there is a Fintek device, just at a
different address. So I propose to degrade this message to a debug
message.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2009-02-17 19:59:54 +01:00
Martin Kebert
87357d277a lis3lv02d: add axes knowledge for HP 6710
Add support for the HP laptops of model 6710x for having correctly setup
axes.

Signed-off-by: Martin Kebert <gkmarty@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-05 12:56:47 -08:00
Pavel Herrmann
c77a022d29 lis3lv02d: add axes knowledge for HP 6730
Add support for the HP laptops of model 6730x for having correctly setup
axes.

Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-05 12:56:47 -08:00
Eric Piel
80eda5fb58 lis3lv02d: add axes knowledge for HP 6530
Add support for the HP laptops of model 6530x for having correctly setup
axes.

Reported-by: Jerome Poulin <jeromepoulin@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-05 12:56:47 -08:00
Jiri Tersel
6bfef2b3cf lis3lv02d: add axes knowledge for HP 6510b
According to dmesg my laptop model HP 6510b is not being recognized by this
driver. After I have modified "lis3lv02d.c" axes in Neverball are OK.

Signed-off-by: Jiri Tersel <tersel@mail.muni.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-05 12:56:47 -08:00
Bharath Ramesh
fb9f88e1dc hwmon: applesmc: add support for MacPro 3 temperature sensors
MacPro 3 have more temperature sensors than the previous MacPro's also the
sensor THTG has been removed.  This patch add supports for the newer
temperature sensors in the MacPro3.

Signed-off-by: Bharath Ramesh <bramesh@vt.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-29 18:04:45 -08:00
Linus Torvalds
7e92214b53 Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
  hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
  hwmon: (abituguru3) Match partial DMI board name strings
  hwmon: Add a driver for the ADT7475 hardware monitoring chip
  hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
  hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
  hwmon: (k8temp) Warn about fam F rev F errata
2009-01-15 16:40:12 -08:00
Pavel Machek
9e1c9d8655 hp_accel: do not call ACPI from invalid context
The LED on HP notebooks is connected through ACPI.  That unfortunately
means that it needs to be delayed by using schedule_work() to avoid
calling the ACPI interpreter from an invalid context.

[akpm@linux-foundation.org: use flush_work() rather than sort-of reimplementing it]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-15 16:39:41 -08:00
Eric Piel
9e0c797821 lis3lv02d: merge with leds hp disk
Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver.  From a purely Linux developer's point of view,
the led and the accelerometer have nothing related.  However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module.  Also make it requires the led class to compile and
update the Kconfig text.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-15 16:39:40 -08:00
Alex Murray
c3d6362b87 hwmon: applesmc: fix light sensor readings on newer MacBooks
The light sensors ALV0 and ALV1 on newer MacBooks (early 2008 and later)
changed to report 10 bytes instead the earlier 6, and the sensor encoding
subsequently changed.  As a result, the reported light sensors readings
are much too low.

Via experiments leading up to this patch, it seems only the ALV0 is
reporting data, and the most useful value therein is a 10-bit big-endian
value at offset 6.  This suggests that a new protocol was added as a
backward-compatible replacement on top of the old one.

This patch makes applesmc report the improved light sensor reading for the
new machines, on a scale in conformance with earlier ones.

Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-15 16:39:39 -08:00
Alistair John Strachan
46a5f173fc hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
When CONFIG_DMI is not enabled, dmi detection should flag that no board
could be detected (err=1) rather than another error condition (err<0).

This fixes the fallback to manual probing for all motherboards, even
those without DMI strings, when CONFIG_DMI=n.

Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-15 22:27:48 +01:00
Alistair John Strachan
3907a8def7 hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
Switch the IN9 32X MAX over from port probing to the preferred DMI
probe method.

Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Paul Hartman <paul.hartman+gentoo@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-15 22:27:48 +01:00
Alistair John Strachan
058943ddcb hwmon: (abituguru3) Match partial DMI board name strings
The switch-over to using DMI board strings to identify abituguru3 compatible
mainboards works most of the time, but sometimes the vendor has substantially
modified the board string between BIOS revisions.

We have found that the vendor chipset identification string (provided in
brackets) changes frequently and is of no use to us. The rest of the board
string sometimes changes in subtle ways, e.g. whitespace or variations in
capitalization.

The new comparison code checks only a part of the supplied DMI board string,
trimming the bracketed content, whitespace, and ignoring case as necessary.

This fixes a bug where an IP35 Pro running an early BIOS would not be
detected without the force=1 module parameter, and also speculatively
fixes other similiar issues.

Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Nick Pasich <NewsLetters@nickandbarb.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-15 22:27:47 +01:00
Jordan Crouse
1c301fc539 hwmon: Add a driver for the ADT7475 hardware monitoring chip
Hwmon driver for the ADT7475 chip.

Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-15 22:27:47 +01:00
Andreas Herrmann
76ff08da34 hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
Current Temperature for K8 RevG desktop CPUs is a "normalized value"
which can be below ambient temperature.

As a consequence lots of RevG systems report temperatures like:

$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp:    +17 C
Core0 Temp:     +3 C
Core1 Temp:    +21 C
Core1 Temp:     +5 C

being quite below ambient temperature.
There are even reports of negative temperature values.

This patch corrects the temperature reporting of k8temp for
RevG desktop CPUs.

Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-15 22:27:47 +01:00
Andreas Herrmann
a2e066bba2 hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
Meaning of ThermSenseCoreSel bit was inverted beginning with K8 RevF.
That means with current driver temp1/temp2 belong to core 1 and
temp3/temp4 belong to core 0 on a K8 RevF/RevG CPU.

This patch ensures that temp1/temp2 always belong to core 0 and
temp3/temp4 to core 1 for all K8 revisions.

Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-15 22:27:47 +01:00
Andreas Herrmann
bb9a35f293 hwmon: (k8temp) Warn about fam F rev F errata
Add warning about wrong CPU temperature readouts on all fam F rev F.

The allowed combinations of processors ensure that all processors
in a multisocket system have similar characteristics, e.g.

(1) provide temperature sensor interface (>=RevC && <RevF)
(2) are affected by erratum #141 (>=RevF)

Thus it is sufficient to check the revision of the boot CPU.

For "mixed silicon support" refer to
"Revision Guide for AMD Athlon 64 and AMD Opteron Processors" (RevA-E) and
"Revision Guide for AMD NPT Family 0Fh Processors" (RefF-G).

Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-15 22:27:46 +01:00
Eric Piel
cfce41a6d6 LIS3LV02D: separate the core from HP ACPI API
The sensor can be accessed via various buses.  In particular, SPI, I²C
and, on HP laptops, via a specific ACPI API (the only one currently
supported).  Separate this latest platform from the core of the sensor
driver to allow support for the other bus type.  The second, and more
direct goal is actually to be able to merge this part with the
hp-disk-leds driver, which has the same ACPI PNP number.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-09 16:54:42 -08:00
Linus Torvalds
2f2408a88c Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (29 commits)
  hwmon: Fix various typos
  hwmon: Check for ACPI resource conflicts
  hwmon: (lm70) Add TI TMP121 support
  hwmon: (lm70) Code streamlining and cleanup
  hwmon: Deprecate the fscher and fscpos drivers
  hwmon: (fschmd) Add watchdog support
  hwmon: (fschmd) Cleanups for watchdog support
  hwmon: (i5k_amb) Load automatically on all 5000/5400 chipsets
  hwmon: (it87) Add support for the ITE IT8720F
  hwmon: Don't overuse I2C_CLIENT_MODULE_PARM
  hwmon: Add LTC4245 driver
  hwmon: (f71882fg) Fix fan_to/from_reg prototypes
  hwmon: (f71882fg) Printout fan modes
  hwmon: (f71882fg) Add documentation
  hwmon: (f71882fg) Fix auto_channels_temp temp numbering with f8000
  hwmon: (f71882fg) Add missing pwm3 attr for f71862fg
  hwmon: (f71882fg) Add F8000 support
  hwmon: (f71882fg) Remove the fan_mode module option
  hwmon: (f71882fg) Separate max and crit alarm and beep
  hwmon: (f71882fg) Check for hwmon powerdown state
  ...
2009-01-07 11:59:51 -08:00
Linus Torvalds
57c44c5f6f Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
  trivial: chack -> check typo fix in main Makefile
  trivial: Add a space (and a comma) to a printk in 8250 driver
  trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
  trivial: Fix misspelling of "firmware" in powerpc Makefile
  trivial: Fix misspelling of "firmware" in usb.c
  trivial: Fix misspelling of "firmware" in qla1280.c
  trivial: Fix misspelling of "firmware" in a100u2w.c
  trivial: Fix misspelling of "firmware" in megaraid.c
  trivial: Fix misspelling of "firmware" in ql4_mbx.c
  trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
  trivial: Fix misspelling of "firmware" in ipw2100.c
  trivial: Fix misspelling of "firmware" in atmel.c
  trivial: Fix misspelled firmware in Kconfig
  trivial: fix an -> a typos in documentation and comments
  trivial: fix then -> than typos in comments and documentation
  trivial: update Jesper Juhl CREDITS entry with new email
  trivial: fix singal -> signal typo
  trivial: Fix incorrect use of "loose" in event.c
  trivial: printk: fix indentation of new_text_line declaration
  trivial: rtc-stk17ta8: fix sparse warning
  ...
2009-01-07 11:31:52 -08:00
Jean Delvare
77fa49d94a hwmon: Fix various typos
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
2009-01-07 16:37:35 +01:00
Jean Delvare
b9acb64a38 hwmon: Check for ACPI resource conflicts
Check for ACPI resource conflicts in hwmon drivers. I've included
all Super-I/O and PCI drivers.

I've voluntarily left out:
* Vendor-specific drivers: if they conflicted on any system, this would
  pretty much mean that they conflict on all systems, and we would know
  by now.
* Legacy ISA drivers (lm78 and w83781d): they only support chips found
  on old designs were ACPI either wasn't supported or didn't deal with
  thermal management.
* Drivers accessing the I/O resources indirectly (e.g. through SMBus):
  the checks are already done where they belong, i.e. in the bus drivers.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
2009-01-07 16:37:35 +01:00
Manuel Lauss
c8ac32e471 hwmon: (lm70) Add TI TMP121 support
The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution.  This patch extends the
LM70 driver to support the TMP121.  The TMP123 differs in pin assign-
ment.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-07 16:37:34 +01:00
Kaiwan N Billimoria
2b7300513b hwmon: (lm70) Code streamlining and cleanup
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).

Other fixes:  doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.

Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-07 16:37:34 +01:00
Hans de Goede
0589c2de64 hwmon: Deprecate the fscher and fscpos drivers
Now that the new merged fschmd driver has gained support for the watchdog
integrated into these IC's, there is no more reason to keep the old fscher
and fscpos drivers around, so mark them as deprecated.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-07 16:37:33 +01:00
Hans de Goede
97950c3d42 hwmon: (fschmd) Add watchdog support
This patch adds support for the watchdog part found in _all_ supported FSC
sensor chips.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-07 16:37:33 +01:00
Hans de Goede
453e308d77 hwmon: (fschmd) Cleanups for watchdog support
Various small cleanups in preparation of adding watchdog support,
mostly removing _MASK postfix from defines which are not masks.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-07 16:37:33 +01:00
Darrick J. Wong
6e31eb2b29 hwmon: (i5k_amb) Load automatically on all 5000/5400 chipsets
It turns out that we cannot create a pci_driver in this driver because PCI will
not call this module's probe function if the i5000-edac driver is already
loaded.  That said, we only want one value (AMBASE) from the PCI config space.
Neither driver alters this value, so it's safe to read it.  However, we still
want the module aliases, so provide that.

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-07 16:37:33 +01:00
Jean-Marc Spaggiari
b4da93e4b0 hwmon: (it87) Add support for the ITE IT8720F
Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.

Signed-off-by: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-01-07 16:37:32 +01:00
Jean Delvare
3aed198c35 hwmon: Don't overuse I2C_CLIENT_MODULE_PARM
I2C_CLIENT_MODULE_PARM is overkill for force_subclients. We really
only use 4 out of the 48 slots, so we're better defining a custom
variable instead. This change saves 92 bytes of data for each of the
five drivers affected.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
2009-01-07 16:37:32 +01:00