This patch changes the loop over the "reg" tuples to not exit
directly upon of_address_to_resource() failure but to continue
with the next "reg" tuple instead. This failure could be due to
size = 0, which might be passed via the device-tree.
This is needed for boards, where a "reg" tuple might have size 0
(of_address_to_resource() returns with EINVAL when size = 0).
Example:
Fully equipped board:
reg = <0 0x00000000 0x00400000
0 0x00400000 0x00400000>;
Partially equipped board:
reg = <0 0x00000000 0x00400000
0 0x00400000 0x00000000>;
This could be the case on boards with runtime detection of
multiple NOR flash configurations where the detected flash size
is inserted into the dtb in U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes sparse warning for static declaration of variable "use_dma"
drivers/mtd/nand/omap2.c:114:11: warning: symbol 'use_dma' was not declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the appropriate conversions to correct the endianness
issues in the MTD driver whenever it accesses the device tree (which is
always big endian).
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I used this to check the BBT on flash together with a hack in mtdchar in
order to read bad blocks.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
it will create an empty BBT table without considering vendor's BBT
information. Vendor's information may be unavailable if the NAND
controller has a different DATA & OOB layout or this information may be
allready purged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The first (sixt) byte in the OOB area contains vendor's bad block
information. During identification of the NAND chip this information is
collected by scanning the complete chip.
The option NAND_USE_FLASH_BBT is used to store this information in a sector so
we don't have to scan the complete flash. Unfortunately the code stores
a marker in order to recognize the BBT in the OOB area. This will fail
if the OOB area is completely used for ECC.
This patch introduces the option NAND_USE_FLASH_BBT_NO_OOB which has to be
used with NAND_USE_FLASH_BBT. It will then store BBT on flash without
touching the OOB area. The BBT format on flash remains same except the
first page starts with the recognition pattern followed by the version byte.
This change was tested in nandsim and it looks good so far :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No code change.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
S5PC210 has the same OneNAND controller as S5PC110
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Implement DMA interrupt method. previous time it polls the DMA status.
It can reduce the CPU power but decrease the performance a little.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When use HIGHMEM, dma_map_single doesn't get the proper DMA address.
So use the dma_map_page in this case.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After S5PC110 use the generic method for OneNAND.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MLC NAND Flash differs from the SLC NAND flash in functioning
and the cell structure. Therefore we are considering it as a
different Flash type.
Signed-off-by: Rohit H.S <rohit.hs@samsung.com>
Signed-off-by: Raghav Gupta <gupta.raghav@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There's no case timeout but add it for some H/W problem or
wrong codes implementation
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not all the NAND devices have all the information in additional
id bytes.
So add a hook in the nand_chip{} is a good method to calculate the
right value of oobsize, erasesize and so on.
Without the hook,you will get the wrong value, and you have to hack
in the ->scan_bbt() to change the wrong value which make the code
mess.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for mtd repartition based on the block
device BLKPG interface:
BLKPG_ADD_PARTITION - for partition creation;
BLKPG_DEL_PARTITION - for partition delete
The usage is based on BLKPG ioctl called with
struct blkpg_ioctl_arg argument which includes the
reference to struct blkpg_partition discribing the
partition offset and length.
Disadvantage: there is no implementation for mtd
flags control. The flags are always borrowed from
the master device.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd_is_master, mtd_add_partition and mtd_del_partition functions
are added to give the possibility of partition manipulation
by ioctl request.
The old partition add function is modified to fit the dynamic
allocation.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is the same driver submitted by ST Micros SPEAr team but
generalized and tested on the ST-Ericsson U300. It probably
easily works on the NHK8815 too.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the Winbond W25Q64 serial flash.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently MTD caches the last read NAND page, even if there was an uncorrectable ECC
error. This patch prevents caching in case of uncorrectable ECC errors. The reason
is that we want to allow the user to re-read the NAND page several times. In case of
unstable bits re-trying may help.
Moreover, current behavior is wrong because the first read returns -EBADMSG (correctly)
but the second read succeeds and incorrectly returns 0 (because we read from the cache).
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for parsing Broadcom BCM63xx image tag format and
creating MTD partitions accordingly. This driver is a platform_device which
can be instantiated accordingly by bcm63xx board support code.
Signed-off-by: Daniel Dickinson <cshore@csolve.net>
Signed-off-by: Mike Albon <malbon@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If "ur_idx" is wrong we could go past the end of the array. The
"ur_idx" comes from root so it's not a huge deal, but adding a sanity
check makes the code more robust.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the build warning:
drivers/mtd/nand/fsl_upm.c: In function 'fun_chip_init':
drivers/mtd/nand/fsl_upm.c:190: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Only 3 warnings are left, one is off by one character, but splitting the line
would reduce the readability. One is for a for loop statement, which would also
not improve readability. The last one is a false positive on a test.
Artem: it is much easier to verify patches against nand_base.c with
checkpatch.pl when nand_base.c itself does not have so many
checkpatch.pl warnings.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Artem: it is much easier to verify patches against nand_base.c with
checkpatch.pl when nand_base.c itself does not have so many
checkpatch.pl warnings.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sudhakar found out that 100µs are enough. Sadly, his updated patch was
overlooked and an older version still using 100ms was merged. Fix this.
Reference: http://patchwork.ozlabs.org/patch/59180/
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for Spansion S25FL016K and S25FL064K SPI flash.
It has been tested with physical devices. Note that both parts exhibit
a Winbond manufacturer ID so they might also be added to that section.
Signed-off-by: Gernot Hoyler <Gernot.Hoyler@spansion.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In order to reduce the indentation and improve the readability of nand_get_
flash_type, split the ONFI detection logic to its own function. The detection
logic inside nand_flash_detect_onfi is also rewritten to allow for less
indentation.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for reading NAND device ONFI parameters and use
the ONFI informations to define its geometry. In case the device supports
ONFI, the onfi_version field in struct nand_chip contains the version (BCD)
and the onfi_params structure can be used by drivers to set up timings and
such. We currently only support ONFI 1.0 parameters.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
S5PC110 OneNAND controller use the generic functions provided from onenand_base.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are some additions to the detection scheme used by Samsung
MLC NAND. These simple changes to support the 400- and 436-byte OOB
are found in the following data sheet:
Samsung K9GBG08U0M (p.40)
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This code isn't reachable. I looked through the git history and it
hasn't been reachable for years. Someone removed the label to silence
gcc's unused label warning but these few lines accidentally got left
behind.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For different command need different oob requirement, set the proper
oob length by different cmd.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After probe, all info already transfer to driver structure.
There is no need to keep the original flash info.
So that we could safely free the flash info in memory, which may grows
larger when more flash is suported.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We certainly don't need to send read id command times by times, since
we already know what the id is after the first read id...
So create a default timing which could ensure it would successfully read
id out all supported chip. Then follow the build-in table to reconfigure
the timing.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adding a new flash definition would need less code.
Keep the platform passing flash definition method.
If one flash is both defined in platform data and builtin table,
driver would select the one from platform data first.
By this way, platform could select the timing most suit for itself,
not need to follow the common settings.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Toshiba does not use ONFI for their NAND flash. So we have to continue
to add new IDs used by Toshiba devices as well as heuristic detection
for scanning the 2nd page for a BBM. This is a relatively harmless
start at supporting many of them.
These chips mostly follow the same ID fields of previous generations,
but there is a need for a tweak.
These chips introduce a strange 576 byte OOB (that's 36 bytes per
512 bytes of page). In the preliminary data, Toshiba has not
defined exactly how their ID strings should decode. In the future,
a new tweak must be added.
Data is taken from, among others, Toshiba TC58TxG4S2FBAxx
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove the MTD!=n dependency since that is handled by drivers/mtd/Kconfig.
Simplify the dependency checks for mtd/chips by using if/endif blocks. Remove
all default n since that is the Kconfig default.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There were some improvements and additions necessary in the
comments explaining of the expansion of nand_ecclayout, the
introduction of nand_ecclayout_user, and the deprecation of the
ioctl ECCGETLAYOUT.
Also, I found a better placement for the macro MTD_MAX_ECCPOS_ENTRIES;
next to the definition of MTD_MAX_OOBFREE_ENTRIES in mtd-abi.h. The macro
is really only important for the ioctl code (found in drivers/mtd/mtdchar.c)
but since there are small edits being made to the user-space header, I
figured this is a better location.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
struct nand_ecclayout is too small for many new chips; OOB regions can be as
large as 448 bytes and may increase more in the future. Thus, copying that
struct to user-space with the ECCGETLAYOUT ioctl is not a good idea; the ioctl
would have to be updated every time there's a change to the current largest
size.
Instead, the old nand_ecclayout is renamed to nand_ecclayout_user and a
new struct nand_ecclayout is created that can accomodate larger sizes and
expand without affecting the user-space. struct nand_ecclayout can still
be used in board drivers without modification -- at least for now.
A new function is provided to convert from the new to the old in order to
allow the deprecated ioctl to continue to work with truncated data. Perhaps
the ioctl, the conversion process, and the struct nand_ecclayout_user can be
removed altogether in the future.
Note: There are comments in nand/davinci_nand.c::nand_davinci_probe()
regarding this issue; this driver (and maybe others) can be updated to
account for extra space. All kernel drivers can use the expanded
nand_ecclayout as a drop-in replacement and ignore its benefits.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some Spansion chips have a method for determining eraseblock size that
is incompatible with similar ID chips of other sizes. This implements
some heuristic detection of these differences.
This patch checks for a 5-byte ID with trailing zeros as well as a
512-byte page size to ensure that chips are not misdetected as the
S30MLxxxP ORNAND series.
[Tweaked by Artem a bit]
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Drivers may (and do) return negative errno values other than -1 from the
ecc.correct callback.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6:
mtd: pxa3xx: fix build error when CONFIG_MTD_PARTITIONS is not defined
mtd: mxc_nand: configure pages per block for v2 controller
mtd: OneNAND: Fix loop hang when DMA error at Samsung SoCs
mtd: OneNAND: Fix 2KiB pagesize handling at Samsung SoCs
mtd: Blackfin NFC: fix invalid free in remove()
mtd: Blackfin NFC: fix build error after nand_scan_ident() change
mxc_nand: Do not do byte accesses to the NFC buffer.
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch initializes the pages per block field in CONFIG1 for
v2 controllers. It also sets the FP_INT field. This is the last
field not correctly initialized, so we can switch from
read/modify/write the CONFIG1 reg to just write the correct
value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When DMA error occurs. it's loop hang since it can't exit the loop.
and it's the right DMA handling code as Spec.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
