Calling irq_find_mapping from outside a irq_{enter,exit} section is
unsafe and produces ugly messages if CONFIG_PROVE_RCU is enabled:
If coming from the idle state, the rcu_read_lock call in irq_find_mapping
will generate an unpleasant warning:
<quote>
===============================
[ INFO: suspicious RCU usage. ]
3.16.0-rc1+ #135 Not tainted
-------------------------------
include/linux/rcupdate.h:871 rcu_read_lock() used illegally while idle!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
#0: (rcu_read_lock){......}, at: [<ffffffc00010206c>]
irq_find_mapping+0x4c/0x198
</quote>
As this issue is fairly widespread and involves at least three
different architectures, a possible solution is to add a new
handle_domain_irq entry point into the generic IRQ code that
the interrupt controller code can call.
This new function takes an irq_domain, and calls into irq_find_domain
inside the irq_{enter,exit} block. An additional "lookup" parameter is
used to allow non-domain architecture code to be replaced by this as well.
Interrupt controllers can then be updated to use the new mechanism.
This code is sitting behind a new CONFIG_HANDLE_DOMAIN_IRQ, as not all
architectures implement set_irq_regs (yes, mn10300, I'm looking at you...).
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1409047421-27649-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Create a new interface and confine it with a config switch which makes
clear that this is just legacy support and not to be used for new code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140507154340.574437049@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Not really the solution to the problem, but at least it confines the
mess in the core code and allows to get rid of the create/destroy_irq
variants from hell, i.e. 3 implementations with different semantics
plus the x86 specific variants __create_irqs and create_irq_nr
which have been invented in another circle of hell.
x86 : x86 should be converted to irq domains and I'm deliberately
making it impossible to do the multi-vector MSI support by
adding more crap to the current mess. It's not that hard to do
and I'm really tired of the trainwrecks which have been invented
by baindaid engineering so far. Any attempt to do multi-vector
MSI or ioapic hotplug without converting to irq domains is NAKed
hereby.
tile: Might use irq domains as well, but it has a very limited
interrupt space, so handling it via this functionality might be
the right thing to do even in the long run.
ia64: That's an hopeless case, as I doubt that anyone has the stomach
to rewrite the homebrewn dynamic allocation facilities. I stared
at it for a couple of hours and gave up. The create/destroy_irq
mess could be made private to itanic right away if there
wouldn't be the iommu/dmar driver being shared with x86. So to
do that I'm going to add a separate ia64 specific implementation
later in order not to deep-six itanic right away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20140507154334.208629358@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The generic_chip.c uses interfaces from irq_domain.c which is
controlled by the IRQ_DOMAIN config option, but there is no Kconfig
dependency so the build can fail:
linux/kernel/irq/generic-chip.c:400:11: error:
'irq_domain_xlate_onetwocell' undeclared here (not in a function)
Select IRQ_DOMAIN when GENERIC_IRQ_CHIP is selected.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Link: http://lkml.kernel.org/r/1391129410-54548-2-git-send-email-nitin.a.kamble@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # 3.11+
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The actual name of the irq_domain mapping debugfs file is
"irq_domain_mapping" not "virq_mapping".
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
The debugfs code is really generic for all platforms. This patch removes the
powerpc-specific directory reference and makes it available to all
architectures.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On ARM, we don't want SPARSE_IRQ to be a user visible option. Make
SPARSE_IRQ visible based on MAY_HAVE_SPARSE_IRQ instead of depending
on HAVE_SPARSE_IRQ.
With this, SPARSE_IRQ is not visible on C6X and ARM.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is a replacment for the cell flow handler which is in the way of
cleanups. Must be selected to avoid general bloat.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some archs want to print extra information for certain irq_chips which
is per irq and not per chip. Allow them to provide a chip callback to
print the chip name and the extra information.
PowerPC wants to print the LEVEL/EDGE type information. Make it configurable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a commandline parameter "threadirqs" which forces all interrupts except
those marked IRQF_NO_THREAD to run threaded. That's mostly a debug option to
allow retrieving better debug data from crashing interrupt handlers. If
"threadirqs" is not enabled on the kernel command line, then there is no
impact in the interrupt hotpath.
Architecture code needs to select CONFIG_IRQ_FORCED_THREADING after
marking the interrupts which cant be threaded IRQF_NO_THREAD. All
interrupts which have IRQF_TIMER set are implict marked
IRQF_NO_THREAD. Also all PER_CPU interrupts are excluded.
Forced threading hard interrupts also forces all soft interrupt
handling into thread context.
When enabled it might slow down things a bit, but for debugging problems in
interrupt code it's a reasonable penalty as it does not immediately
crash and burn the machine when an interrupt handler is buggy.
Some test results on a Core2Duo machine:
Cache cold run of:
# time git grep irq_desc
non-threaded threaded
real 1m18.741s 1m19.061s
user 0m1.874s 0m1.757s
sys 0m5.843s 0m5.427s
# iperf -c server
non-threaded
[ 3] 0.0-10.0 sec 1.09 GBytes 933 Mbits/sec
[ 3] 0.0-10.0 sec 1.09 GBytes 934 Mbits/sec
[ 3] 0.0-10.0 sec 1.09 GBytes 933 Mbits/sec
threaded
[ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec
[ 3] 0.0-10.0 sec 1.09 GBytes 934 Mbits/sec
[ 3] 0.0-10.0 sec 1.09 GBytes 937 Mbits/sec
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20110223234956.772668648@linutronix.de>
"def_bool n" without prompt is pointless, these should be just "bool".
[ tglx: Adapted to latest changes ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4D5D3309020000780003264A@vpn.id2.novell.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
sparc64 needs to call a preflow handler on certain interrupts befor
calling the action chain. Integrate it into handle_fasteoi_irq. Must
be enabled via CONFIG_IRQ_FASTEOI_PREFLOW. No impact when disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David S. Miller <davem@davemloft.net>
The saving of this switch is minimal versus the ifdef mess it
creates. Simple enable PER_CPU unconditionally and remove the config
switch.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need to maintain the flag for now in both fields status and istate.
Add a CONFIG_GENERIC_HARDIRQS_NO_COMPAT switch to allow testing w/o
the status one. Wrap the access to status IRQ_INPROGRESS in a inline
which can be turned of with CONFIG_GENERIC_HARDIRQS_NO_COMPAT along
with the define.
There is no reason that anything outside of core looks at this. That
needs some modifications, but we'll get there.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All archs implement show_interrupts() in more or less the same
way. That's tons of duplicated code with different bugs with no
value. Implement a generic version and deprecate show_interrupts()
Unfortunately we need some ifdeffery for !GENERIC_HARDIRQ archs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All architectures are finally converted. Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
The move_irq_desc() function was only used due to the problem that the
allocator did not free the old descriptors. So the descriptors had to
be moved in create_irq_nr(). That's history.
The code would have never been able to move active interrupt
descriptors on affinity settings. That can be done in a completely
different way w/o all this horror.
Remove all of it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
This option covers now the old chip functions and the irq_desc data
fields which are moving to struct irq_data. More stuff will follow.
Pretty handy for testing a conversion, whether something broke or not.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The generic irq Kconfig options are copied around all archs. Provide a
generic Kconfig file which can be included.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121843.217333624@linutronix.de>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
