Commit Graph

16 Commits

Author SHA1 Message Date
Adrian Hunter
0f8d8ea64e mmc: Fixes for Dual Data Rate (DDR) support
The DDR support patch needs the following fixes:

- The block driver does not need to know about DDR, any more
  than it needs to know about bus width.
- Not only the card must be switched to DDR mode.  The host
  controller must also be configured, which is done through
  the 'set_ios()' function.
- Do not set the DDR mode state until after the switch command
  is successful.
- Setting block length is not supported in DDR mode.  Make that
  a core function and change the other place it is used (mmc_test)
  also.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23 21:11:16 +08:00
Hanumath Prasad
dfc13e8402 mmc: MMC 4.4 DDR support
Add support for Dual Data Rate MMC cards as defined in the 4.4
specification.

Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23 21:11:16 +08:00
Adrian Hunter
dfe86cba76 mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation.  In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.

SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.

"erase_size" is the minimum size, in bytes, of an erase operation.  For
MMC, "erase_size" is the erase group size reported by the card.  Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector.  For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.

SD/MMC cards can erase an arbitrarily large area up to and
including the whole card.  When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:

    1. A single erase command will make all other I/O on the card
       wait.  This is not a problem if the whole card is being erased, but
       erasing one partition will make I/O for another partition on the
       same card wait for the duration of the erase - which could be a
       several minutes.

    2. To be able to inform the user of erase progress.

    3. The erase timeout becomes too large to be very useful.
       Because the erase timeout contains a margin which is multiplied by
       the size of the erase area, the value can end up being several
       minutes for large areas.

"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.

For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.

For SD, "preferred_erase_size" is the allocation unit size specified by
the card.

"preferred_erase_size" is in bytes.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-12 08:43:30 -07:00
Adrian Hunter
319a3f1429 mmc: allow host claim / release nesting
This change allows the MMC host to be claimed in situations where the host
may or may not have already been claimed.  Also 'mmc_try_claim_host()' is
now exported.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:33 -07:00
Anton Vorontsov
86e8286a0e mmc: Add mmc_vddrange_to_ocrmask() helper function
This function sets the OCR mask bits according to provided voltage
ranges. Will be used by the mmc_spi OpenFirmware bindings.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-12-31 18:18:13 +01:00
Pierre Ossman
ad3868b2ec mmc,sdio: helper function for transfer padding
There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.

A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-07-15 14:14:44 +02:00
David Brownell
97018580c4 MMC headers learn about SPI
Teach the MMC/SD/SDIO system headers that some hosts use SPI mode

 - New host capabilities and status bits
    * MMC_CAP_SPI, with mmc_host_is_spi() test
    * mmc_host.use_spi_crc flag

 - SPI-specific declarations:
    * Response types, MMC_RSP_SPI_R*
    * Two SPI-only commands
    * Status bits used native to SPI:  R1_SPI_*, R2_SPI_*

 - Fix a few (unrelated) whitespace bugs in the headers.

 - Reorder a few mmc_host fields, removing several bytes of padding

None of these changes affect current code.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:37:51 +02:00
Nicolas Pitre
2342f3323c sdio: allow for mmc_claim_host to be aborted
It is sometimes necessary to give up on trying to claim the host lock,
especially if that happens in a thread that has to be stopped.

While at it, fix the description for mmc_claim_host() which was wrong.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:55:13 +02:00
Pierre Ossman
b2bcc798bb mmc: implement SDIO IO_RW_DIRECT operation
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:42:37 +02:00
Pierre Ossman
5c4e6f1301 mmc: detect SDIO cards
Really basic init sequence for SDIO cards.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:40:07 +02:00
Pierre Ossman
be0192aae1 mmc: remove confusing flag
The MMC_DATA_MULTI flag never had a proper definition of what it
means, so remove it and let the drivers check the block count in
the request.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:15:12 +02:00
Pierre Ossman
b146d26a61 mmc: mmc_set_data_timeout() parameter write is redundant
The write parameter in mmc_set_data_timeout() is redundant as the
data structure contains information about the direction of the
transfer.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:15:00 +02:00
Pierre Ossman
17b0429dde mmc: remove custom error codes
Convert the MMC layer to use standard error codes and not its own,
incompatible values.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 08:46:48 +02:00
Pierre Ossman
67a61c4847 mmc: update kerneldoc
Make sure the kerneldoc comments are up to date and relevant.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-26 01:53:39 +02:00
Pierre Ossman
da7fbe58d2 mmc: Separate out protocol ops
Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-01 13:04:18 +02:00
Pierre Ossman
aaac1b470b mmc: Move core functions to subdir
Create a "core" subdirectory to house the central bus handling
functions.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-01 13:04:18 +02:00