SetPageDirty() and ClearPageDirty() are low-level thing which filesystems
shouldn't be using. They bypass dirty page accounting.
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IA64 is using the generic version of __raw_read_trylock, which always
waits for the lock to be free instead of returning when the lock is in
use. Define an ia64 version of __raw_read_trylock which behaves
correctly, and drop the generic one.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Lothar Wassmann
The patch makes sure, that the ouptut functions of pins are restored
before restoring the Alternat Function settings, preventing pins from
being intermediately configured for undefined or unwanted alternate
functions.
Here is the original comment:
I've got a PXA270 system that uses GPIO80 as nCS4. This system did
hang on resume. Digging into the problem I found that the processor
stalled immediately when restoring the GAFR2_U register which restored
the alternate function for GPIO80. Since the GPDR registers were
restored after the GAFR registers, the offending GPIO was configured
as input at this point.
Thus the alternate function that was in effect after restoring the
GAFR was in fact the input function "MBREQ" instead of the output
function "nCS4". The "PXA27x Processor Family Developer's Manual"
(Footnote in Table 6-1 on page 6-3) states that:
"The MBREQ alternate function must not be enabled until the PSSR[RDH]
bit field is cleared. For more details, see Table 3-15, "PSSR Bit
Definitions" on page 3-71."
There is another note in the Developer's Manual (chapter 24.4.2
"GPIO operation as Alternate Function" on page 24-4)
stating that:
"Configuring a GPIO for an alternate function that is not defined for
it causes unpredictable results."
Since some GPIOs have no input function defined, and to prevent
inadvertedly programming the MBREQ function on some pin, the GAFR
registers should be restored after the GPDR registers have been
restored.
Additional provisions have to be made when the MBREQ function is
actually required. The corresponding GAFR bits should not be restored
with the regular GAFR restore, but must be set only after the PSSR
bits have been cleared.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The VM layer (for historical reasons) turns a read-only shared mmap into
a private-like mapping with the VM_MAYWRITE bit clear. Thus checking
just VM_SHARED isn't actually sufficient.
So use a trivial helper function for the cases where we wanted to inquire
if a mapping was COW-like or not.
Moo!
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the previous commit, we can handle arbitrary shared re-mappings
even without this complexity, and since the only known private mappings
are for strange users of /dev/mem (which never create an incomplete one),
there seems to be no reason to support it.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A shared mapping doesn't cause COW-pages, so we don't need to worry
about the whole vm_pgoff logic to decide if a PFN-remapped page has
gone through COW or not.
This makes it possible to entirely avoid the special "partial remapping"
logic for the common case.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ppc32 kernel, when built with CONFIG_SMP and booted on a single CPU
machine, will not properly set smp_tb_synchronized, thus causing
gettimeofday() to not use the HW timebase and to be limited to jiffy
resolution. This, among others, causes unacceptable pauses when launching
X.org.
Signed-Off-By: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code that sets the clock spreading feature of the Intrepid ASIC
must not be run on some machine models or those won't boot. This
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Nikola Valerjev
Single stepping an application using ptrace() fails over ARM instructions BX and BLX.
Steps to reproduce:
Compile and link the following files
main.c
-----
void foo();
int main() {
foo();
return 0;
}
foo.s
-----
.text
.globl foo
foo:
BX LR
Using ptrace() functionality, run to main(), and start singlestepping.
Singlestep over \"BX LR\" instruction won\'t transfer the control back
to main, but run the code to completion.
This problems seems to be in the function get_branch_address() in
arch/arm/kernel/ptrace.c. The function doesn\'t seem to recognize BX
and BLX instructions as branches. BX and BLX instructions can be used
to convert from ARM to Thumb mode if the target address has the low
bit set. However, they are also perfectly legal in the ARM only mode.
Although other things in the kernel seem to indicate that only ARM
mode is accepted (and not Thumb), many compilers will generate BX
and BLX instructions even when generating ARM only code.
Signed-off-by: Nikola Valerjev <nikola@ghs.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The scsi_library routines don't correctly set DMA_NONE when
req->data_len is zero (instead they check the command type first, so
if it's write, we end up with req->data_len == 0 and direction as
DMA_TO_DEVICE which confuses some drivers)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It is a simple bug which uses the wrong member.
This bug does not seriously affect ordinary use of IPsec.
But it is important to pass IPv6 ready logo phase-2
conformance test of IPsec SGW.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ppc64, when opening a new hugepage region, we need to make sure any
old normal-page SLBs for the area are flushed on all CPUs. There was
a bug in this logic - after putting the new hugepage area masks into
the thread structure, we copied it into the paca (read by the SLB miss
handler) only on one CPU, not on all. This could cause incorrect SLB
entries to be loaded when a multithreaded program was running
simultaneously on several CPUs. This patch corrects the error,
copying the context information into the PACA on all CPUs using the mm
in question before flushing any existing SLB entries.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On most powerpc CPUs, the dcache and icache are not coherent so
between writing and executing a page, the caches must be flushed.
Userspace programs assume pages given to them by the kernel are icache
clean, so we must do this flush between the kernel clearing a page and
it being mapped into userspace for execute. We were not doing this
for hugepages, this patch corrects the situation.
We use the same lazy mechanism as we use for normal pages, delaying
the flush until userspace actually attempts to execute from the page
in question.
Tested on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cache info is setup by walking the device tree in initialize_cache_info().
However, icache_flush_range might be called before that, in
slb_initialize()->patch_slb_encoding, which modifies the load immediate
instructions used with SLB fault code.
Not only that, but depending on memory layout, we might take SLB faults
during unflatten_device_tree. So that fault will load an SLB entry that
might not contain the right LLP flags for the segment.
Either we can walk the flattened device tree to setup cache info, or
we can pick the known defaults that are known to work. Doing it in the
flattened device tree is hairier since we need to know the machine type
to know what property to look for, etc, etc.
For now, it's just easier to go with the defaults. Worst thing that
happens from it is that we might waste a few cycles doing too small
dcbst/icbi increments.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
model_id fields of wf_smu_sys_all_params should match the model ID
they are supposed to represent (as commented). Fixes windfarm on some
iMac 8,1 models.
Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Deepak Saxena
This looks like a leftover from 2.4 days...
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The problem I was seeing turned out to be that skb->dev is NULL when
the checksum is being completed in user context. This happens because
the reference to the device is dropped (to allow it to be released
when packets are in the queue).
Because skb->dev was NULL, the netdev_rx_csum_fault was panicing on
deref of dev->name. How about this?
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eh_action semaphore in scsi_eh_send_command is cleared after a
command timeout. The command is subsequently aborted and the abort
will try to call scsi_done() on it. Unfortunately, the scsi_eh_done()
routine unconditinally completes the semaphore (which is now null).
Fix this race by makiong the scsi_eh_done() routine check that the
semaphore is non null before completing it (mirroring the ordinary
command done/timeout logic).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI megaraid drive goes to great effort to kmap
the scatterlist buffer (if used), but then uses the
wrong pointer when copying to it afterward.
Signed-off-by: Mark Lord <lkml@rtr.ca>
Acked by: Ju, Seokmann <Seokmann.Ju@engenio.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some debug code wasn't properly removed from the initial 64k pages
patch, and while it's harmless, it's also slowing down significantly a
very hot code path, thus it should really be removed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 64k pages patch changed the meaning of one argument passed to the
low level hash functions (from "large" it became "psize" or page size
index), but one of the call sites wasn't properly updated, causing
potential random weird problems with huge pages. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This bug exists in the current code and prevents machines from booting
with numa enabled if there is a node that does not contain memory.
Workaround is to boot with 'numa=off'. Looks like a simple typo.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Local add/sub macros need to have a parameter to specify
the addend/subtrahend respectively.
Signed-off-by: Christoph Lameter <clameter@sgi.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Properly check FC_RESID for any non-transfered bytes
regardless of firmware completion status.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A regression in a recent change
33135aa2a5 caused the driver
to mistakenly drop handling of AENs. Due to the incorrect
handling, ports would not reappear after RSCNs and LIPs.
Drops unused/incorrect compound #define from qla_def.h.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This makes ibmvscsi work correctly with the recent set of kexec
patches that went in. This is based on work by Michael Ellerman, who
chased this initially. He validated that it works during kexec.
Handle kexec correctly in ibmvscsi. During kexec the adapter
will not get cleaned up correctly, so we may need to reset it
to make it sane again.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[ Move assosciated code comment to the correct spot, and
update driver version and release date -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So we can properly use __GFP_COMP and avoid the use of
PG_reserved pages.
With extremely helpful review from Hugh Dickins.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to store the congestion control timestamp on the SKB before we
clone it, not after. Else we get no timestamping information at all.
tcp_transmit_skb() has been reworked so that we can do the timestamp
still in one spot, instead of at all the call sites.
Problem discovered, and initial fix, from Tom Young
<tyo@ee.unimelb.edu.au>.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded call to tcp_vegas_rtt_calc. The more accurate
microsecond value has already been registered prior to calling
tcp_vegas_cong_avoid.
Signed-off-by: Thomas Young <tyo@ee.mu.oz.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the resetting of rtt measurements to inside the once per RTT
block of code.
Signed-off-by: Thomas Young <tyo@ee.mu.oz.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch that added support for a new platform chipset (shub2) broke
PTC deadlock recovery on older versions of the chipset. (PTCs are the
SN platform-specific method for doing a global TLB purge). This
patch fixes deadlock recovery so that it works on both the old & new
chipsets.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We have a customer application which trips a bug. The problem arises
when a driver attempts to call do_munmap on an area which is mapped, but
because current->thread.task_size has been set to 0xC0000000, the call
to do_munmap fails thinking it is an unmap beyond the user's address
space.
The comment in fs/binfmt_elf.c in load_elf_library() before the call
to SET_PERSONALITY() indicates that task_size must not be changed for
the running application until flush_thread, but is for ia64 executing
ia32 binaries.
This patch moves the setting of task_size from SET_PERSONALITY() to
flush_thread() as indicated. The customer application no longer is able
to trip the bug.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The per-node data structures are allocated with strided offsets that are a
function of the node number. This prevents excessive cache-aliasing from
occurring.
On systems with a large number of nodes, the strided offset becomes
too large. This patch restricts the maximum offset to 32MB. This is far larger
than the size of any current L3 cache.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix only patch to add fixup code that sets up
pci_controller->window. This code is a temporary
fix until ACPI support on Altix is added.
Also, corrects the usage of pci_dev->sysdata,
which had previously been used to reference
platform specific device info, to now point to
a pci_controller struct.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The checksum offsets for receive offload were not being set correctly.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The patch (originally from Steve) simply adds memory buffer settings to
DECnet similar to those in TCP.
Signed-off-by: Patrick Caulfield <patrick@tykepenguin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a function takes a function pointer as argument it should use the 'return
(*pointer)(params...)' syntax used everywhere else in the kernel as this is
recognized by kernel-doc.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFA_NEST calls NFA_PUT which jumps to nfattr_failure if the skb has no
room left. We call read_unlock_bh at nfattr_failure for the NFA_PUT inside
the locked section, so move NFA_NEST inside the locked section too.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should have been marked EXPERIMENTAL from the beginning, as the current
bunch of fixes show.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_conntrack_flush() used to be part of ip_conntrack_cleanup(), which needs
to drop _all_ references on module unload. Table flushed using ctnetlink
just needs to clean the table and doesn't need to flush the event cache or
wait for any references attached to skbs. Move everything but pure table
flushing back to ip_conntrack_cleanup().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least, valid nfnetlink message should have nlmsghdr and nfgenmsg.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes nf_conntrack_icmpv6 check that ICMPv6 type isn't < 128
to avoid accessing out of array valid_new[] and invmap[].
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_nat_initialized() takes enum ip_nat_manip_type as it's second argument,
not a hook number.
Noticed and initial patch by Marcus Sundberg <marcus@ingate.com>.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
