Commit Graph

1505 Commits

Author SHA1 Message Date
Mark Lord
00f42eabb2 sata_mv rearrange mv_config_fbs
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet
recommendations for NCQ and FIS-based switching (FBS).

Also, maintain a port flag to let us know when FBS is enabled.
We will make more use of that flag later in this patch series.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:37:40 -04:00
Mark Lord
dd2890f60f sata_mv errata workaround for sata25 part 1
Part 1 of workaround for errata "sata#25" for the 60x1 series
(the second half of this errata workaround is still in development.

Bit22 of the GPIO port has to be set "on" when in NCQ mode.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:37:40 -04:00
Mark Lord
3e4a139107 sata_mv new mv_qc_defer method
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands,
and cannot be used for PIO at all.  So we need to prevent libata
from trying to feed us such mixtures.

Introduce mv_qc_defer() for this purpose, and use it for all chip versions.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:37:39 -04:00
Mark Lord
9b2c4e0bae sata_mv wait for empty+idle
When performing EH, it is recommended to wait for the EDMA engine
to empty out requests-in-progress before disabling EDMA.

Introduce code to poll the EDMA_STATUS register for idle/empty bits
before disabling EDMA.  For non-EH operation, this will normally exit
without delay, other than the register read.

A later series of patches may focus on eliminating this and various
other register reads (when possible) throughout the driver,
but for now we're focussing on solid reliablity.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:37:39 -04:00
Mark Lord
616d4a98ad sata_mv pci features
Some of the GenIIe EDMA optimizations should not be used
for non-PCI (SOC) devices, and nor for certain configurations
of conventional PCI (non PCI-X, PCIe) buses.

Logic taken/simplified from that in the Marvell proprietary driver.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:37:38 -04:00
Mark Lord
8e7decdb8b sata_mv more cosmetic changes
More cosmetic changes; no code changes.

 -- try and improve consistency of naming.
 -- add missing _OFS to tails of register offset definitions.
 -- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does.
 -- remove/move some dead comments

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:37:38 -04:00
Alek Du
07ab85de4d libata: Add Intel SCH PATA driver
This patch adds Intel SCH chipsets (AF82US15W, AF82US15L, AF82UL11L)
PATA controller support.

Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:33:58 -04:00
Tejun Heo
cb6716c879 ata_piix: verify SIDPR access before enabling it
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write.  Verify SIDPR is actually working before enabling it.

This is reported by Ryan Roth in bz#10512.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:33:53 -04:00
Tejun Heo
78ab88f04f libata: improve post-reset device ready test
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet.  It looks like they use 0xff if device
presence is detected but connection isn't established.  0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.

This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions.  This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.

This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.

Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:32:02 -04:00
Tejun Heo
22b5e7a742 ahci: SB600 ahci can't do MSI, blacklist that capability
This fixes bz#10507.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 17:42:04 -04:00
Alan Cox
a79067e513 libata: More TSSTcorp pain, keep in sync with legacy IDE
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 17:41:13 -04:00
Alan Cox
11f6400e92 pata_via: Fix 6410 misdetect
The discrete VIA ATA chips don't have 0x40 enable bits. We check that
properly in one location but not another. This causes some users 6410
RAID cards to be incorrectly skipped.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 17:41:10 -04:00
Jeff Garzik
d7b5a23fc6 [libata] pata_atiixp: fix PIO timing data misprogramming
Use correct variable, achieve desired result...

Spotted by LKML/linux-ide poster whose name I lost (apologies!)

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 17:39:45 -04:00
Sonic Zhang
65c0d4e54a Fix bug - Implement bfin ata interrupt handler to avoid "irq 68 nobody cared" (v2)
Return IRQ_HANDLED when bfin ata device is busy.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3513

v1-v2:
 - fold api breakage fixing patch together.
 - mark 'static', not 'inline'.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 02:17:18 -04:00
Mark Lord
7368f91926 sata_mv: Improve naming of main_irq cause/mask identifiers
Tidy up naming of things associated with the PCI / SOC chip
"main irq cause/mask" registers, as inspired by Jeff.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 02:17:14 -04:00
Tejun Heo
87340e9834 libata-scsi: improve rbuf handling for simulated commands
Buffer length handling in simulated commands is error-prone and full
of bugs.  There are a number of places where necessary length checks
are missing and if the output buffer is passed in as sglist, nothing
works.

This patch adds a static buffer ata_scsi_rbuf which is sufficiently
large to handle the larges output from simulated commands (4k
currently), let all simulte functions write to the buffer and removes
all length checks as we know that there always is enough buffer space.
Copying in (for ATAPI inquiry fix up) and out are handled by
sg_copy_to/from_buffer() behind ata_scsi_rbuf_get/put() interface
which handles sglist properly.

This patch is inspired from buffer length check fix patch from Petr
Vandrovec.

Updated to use sg_copy_to/from_buffer() as suggested by FUJITA
Tomonori.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vmware.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 02:17:03 -04:00
Tejun Heo
f0761be344 libata-scsi: clean up inquiry / mode sense related functions
* make ata_scsiop_*() static
* make ata_scsi_set_sense() static and move it above its users
* make ata_scsi_rbuf_fill() static
* kill unused ata_scsi_badcmd()

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 02:16:37 -04:00
Ralf Baechle
3dd654bfdf [MIPS] ATA: Rename routerboard 500 to 532
The platform is actually named routerboard 532 so let's call it this.  This
patch only rename files, Kconfig and C symbols; no functional changes.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 02:16:25 -04:00
Al Viro
ac2f217baf typo in sata_fsl
it's ata_link, not ata_linke

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 10:03:31 -07:00
Roel Kluin
f9d4249172 pata_bf54x: decrease count first.
When count reaches 0 the postfix decrement still subtracts (to -1),
so bfin_reset_controller() returns as if the busy flag was cleared
while it was not.

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:26:28 -04:00
Mark Lord
85afb93457 sata_mv: re-enable hotplug, update TODO list
Re-enable hotplug, now that the interrupt/error handling are mostly sane.
Also update the TODO list at the top.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:26:22 -04:00
Mark Lord
8d07379d25 sata_mv: leave SError bits untouched in mv_err_intr
Here it is again, minus the checkpatch.pl complaint:

Rework mv_err_intr() to leave the SError bits as-is,
so that libata-eh has a chance to see/use them.

We originally thought that clearing them here was necessary
before writing back to edma_err_cause (per the Marvell datasheets),
but we will end up reseting the chip regardless in those cases.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:26:14 -04:00
Mark Lord
8f767f8a02 sata_mv: more interrupt handling rework
Continue fixing the interrupt handling logic.

Get rid of mv_intr_pio(), by using ata_sff_host_intr() for PIO..

Add a mv_unexpected_intr() catch-all for "impossible" scenarios,
where we get an interrupt that shouldn't have happened
(never seen in testing, but just in case..).

Rearrange the logic so that we always process completed
response queue entries before looking for other events,
This avoids having to re-issue commands that had already succeeded.

As part of this, we split out some duplicated functionality
into a new function, mv_get_active_qc().

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:26:06 -04:00
Mark Lord
a3718c1f23 sata_mv: tidy host controller interrupt handling
Tidy up host controller interrupt handling, by moving the weirdo
bit shifting from mv_interrupt() to mv_host_intr().

This lets us take advantage of the MV_PORT_TO_SHIFT_AND_HARDPORT() macro
from an earlier patch to greatly simplify the port numbering logic.

Also, defer reading the hc_irq_cause (one per hc) until it is
actually proven to be needed.  This may save a microsecond or
so per interrupt, on average (a later patchset will further reduce
unnecessary register reads throughout the driver).

Apart from that, we still leave the actual IRQ handling logic alone.
Subsequent patches in this series will address that.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:25:57 -04:00
Mark Lord
fcfb1f77ce sata_mv: simplify request/response queue handling
Try and simplify handling of the request/response queues.

Maintain the cached copies of queue indexes in a fully-masked state,
rather than having each use of them have to do the masking.

Split off handling of a single crpb response into a separate function,
to reduce complexity in the main mv_process_crpb_entries() routine.

Ignore the rarely-valid error bits from the crpb status field,
as we already handle that information in mv_err_intr().

For now, preserve the rest of the original logic.
A later patch will deal with fixing that separately.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:25:48 -04:00
Mark Lord
1cfd19aeb8 sata_mv: simplify freeze/thaw bit-shift calculations
Introduce the MV_PORT_TO_SHIFT_AND_HARDPORT() macro,
to centralize/simplify various scattered bits of logic
for calculating bit shifts and the like.

Some of the places that do this get it wrong, too,
so consolidating the algorithm at one place will help
keep the code correct.

For now, we use the new macro in mv_eh_{freeze,thaw}.
A subsequent patch will re-use this in the interrupt handlers

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:25:36 -04:00
Mark Lord
f9f7fe014f sata_mv mask all interrupt coalescing bits
Ignore *all* interrupt coalescing bits on all controllers,
not just some of each.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:11:41 -04:00
Mark Lord
352fab701c sata_mv more cosmetics
More cosmetic cleanups prior to the interrupt/error handling logic changes.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:11:40 -04:00
Dan McGee
01ce2601e4 ata_piix: add Asus Eee 701 controller to short cable list
The drive is directly soldered to the controller, so there is no cable at
all. Remove the 40-wire assumption so the drive can operate at max speed.

Before patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 5.29612 s, 25.3 MB/s

After patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 3.94955 s, 34.0 MB/s

Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:11:39 -04:00
Mark Lord
a6116c9e60 libata-eh set tf flags in NCQ EH result_tf
Fix mis-reporting of NCQ errors by ensuring that result_tf->flags
is properly initialized in libata-eh.  This allows ata_gen_ata_sense()
to report the failed block number correctly to SCSI after a media error
during NCQ.

This patch may also be a candidate for backporting to earlier kernels.
Without this fix, SCSI will fail I/O on the entire request rather
than just the bad sector.  That can be bad for a request that was
merged from many independent read reads from different tasks.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 01:11:37 -04:00
Adrian Bunk
1dc55e8761 make sata_set_spd_needed() static
sata_set_spd_needed() can now become static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 00:46:11 -04:00
Adrian Bunk
6bdb4fc9f9 make sata_print_link_status() static
sata_print_link_status() can now become static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 00:46:09 -04:00
Adrian Bunk
66a9099e02 libata-acpi.c: remove unneeded #if's
These #if's are unneeded since they:
- did anyway not handle the CONFIG_ACPI_DOCK_MODULE case correctly and
- this is already handled in include/acpi/acpi_drivers.h and
- it's now correctly handled in kconfig.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 00:45:52 -04:00
Tejun Heo
a0b9f4bc1e sata_nv: make hardreset return -EAGAIN on success
sata_nv hardreset can't classify but was left out while unifying
follow-up SRST request mechanism[1].  This caused detection failures
on those controllers.  Fix it.

Reported and bisected by Roland Dreier, Petr Vandrovec and Marc
Dionne.  Thanks guys.

[1] 305d2a1ab1

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 00:45:48 -04:00
Tejun Heo
15fe982e42 ahci: retry enabling AHCI a few times before spitting out WARN_ON()
Some chips need AHCI_EN set more than once to actually set it.  Try a
few times before giving up and spitting out WARN_ON().

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 00:45:13 -04:00
Tejun Heo
411cb3869a libata: make WARN_ON conditions in ata_sff_hsm_move() more strict
WARN_ON()'s in ata_hsm_move() was too liberal and got triggerred when
it shouldn't (e.g. hotplug events at the right moment).  As the HSM
only deals with device errors and state machine violations, make it
check only against them.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 00:45:09 -04:00
Kay Sievers
458622fcdc ATA/IDE: fix platform driver hotplug/coldplug
Since 43cc71eed1, the platform modalias
is prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable
ATA and IDE platform drivers, to re-enable auto loading.

NOTE: both ata/pata_platform.c and ide/legacy/ide_platform.c claim
to provide "the" platform_pata driver, and there's no build-time
mutual exclusion mechanism.  This means that configs which enable
both drivers will make some trouble when hotplugging...

[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 00:45:04 -04:00
Tejun Heo
8e5443a098 sata_sis: SCR accessors return -EINVAL when requested SCR isn't available
sis_scr_cfg_read() can't access SError and was incorrectly returning
-1 instead of -EINVAL.  This went unnoticed because SError used to be
cleared in @postreset() and it didn't care about how scr_read() failed
but commit ac371987 moved SError clearing into sata_link_resume() and
SCR access failure other than -EINVAL is considered an error condition
and exposes the incorrect return value bug as detection failure.  Fix
it.

Also, scsi_scr_cfg_write() was incorrectly returning 0 after it
ignored the request to write to SError.  Make it also return -EINVAL.

This was bisected and reported by Patrick McHardy.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-24 23:42:47 -04:00
Harvey Harrison
2b4221bb54 libata: functions with definition should not be extern
Noticed by sparse
drivers/ata/libata-core.c:3380:12: warning: function 'ata_wait_after_reset' with external linkage has definition

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-24 23:42:26 -04:00
Linus Torvalds
e80ab411e5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
  SCSI: convert struct class_device to struct device
  DRM: remove unused dev_class
  IB: rename "dev" to "srp_dev" in srp_host structure
  IB: convert struct class_device to struct device
  memstick: convert struct class_device to struct device
  driver core: replace remaining __FUNCTION__ occurrences
  sysfs: refill attribute buffer when reading from offset 0
  PM: Remove destroy_suspended_device()
  Firmware: add iSCSI iBFT Support
  PM: Remove legacy PM (fix)
  Kobject: Replace list_for_each() with list_for_each_entry().
  SYSFS: Explicitly include required header file slab.h.
  Driver core: make device_is_registered() work for class devices
  PM: Convert wakeup flag accessors to inline functions
  PM: Make wakeup flags available whenever CONFIG_PM is set
  PM: Fix misuse of wakeup flag accessors in serial core
  Driver core: Call device_pm_add() after bus_add_device() in device_add()
  PM: Handle device registrations during suspend/resume
  block: send disk "change" event for rescan_partitions()
  sysdev: detect multiple driver registrations
  ...

Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
2008-04-21 15:49:58 -07:00
Linus Torvalds
429f731dea Merge branch 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc
* 'semaphore' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/misc:
  Deprecate the asm/semaphore.h files in feature-removal-schedule.
  Convert asm/semaphore.h users to linux/semaphore.h
  security: Remove unnecessary inclusions of asm/semaphore.h
  lib: Remove unnecessary inclusions of asm/semaphore.h
  kernel: Remove unnecessary inclusions of asm/semaphore.h
  include: Remove unnecessary inclusions of asm/semaphore.h
  fs: Remove unnecessary inclusions of asm/semaphore.h
  drivers: Remove unnecessary inclusions of asm/semaphore.h
  net: Remove unnecessary inclusions of asm/semaphore.h
  arch: Remove unnecessary inclusions of asm/semaphore.h
2008-04-21 15:41:27 -07:00
Tony Jones
ee959b00c3 SCSI: convert struct class_device to struct device
It's big, but there doesn't seem to be a way to split it up smaller...

Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-19 19:10:33 -07:00
Russell King
cf816ecb53 Merge branch 'merge-fixes' into devel 2008-04-19 17:17:34 +01:00
Russell King
adf6d34e46 Merge branch 'omap2-upstream' into devel 2008-04-19 17:17:29 +01:00
Matthew Wilcox
d3135846f6 drivers: Remove unnecessary inclusions of asm/semaphore.h
None of these files use any of the functionality promised by
asm/semaphore.h.  It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
2008-04-18 22:16:32 -04:00
Linus Torvalds
2cca775bae Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
  [SCSI] iscsi: bidi support for iscsi_tcp
  [SCSI] iscsi: bidi support at the generic libiscsi level
  [SCSI] iscsi: extended cdb support
  [SCSI] zfcp: Fix error handling for blocked unit for send FCP command
  [SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
  [SCSI] zfcp: fix 31 bit compile warnings
  [SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
  [SCSI] bsg: remove minor in struct bsg_device
  [SCSI] bsg: use better helper list functions
  [SCSI] bsg: replace kobject_get with blk_get_queue
  [SCSI] bsg: takes a ref to struct device in fops->open
  [SCSI] qla1280: remove version check
  [SCSI] libsas: fix endianness bug in sas_ata
  [SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
  [SCSI] aacraid: Do not describe check_reset parameter with its value
  [SCSI] aacraid: Fix down_interruptible() to check the return value
  [SCSI] sun3_scsi_vme: add MODULE_LICENSE
  [SCSI] st: rename flush_write_buffer()
  [SCSI] tgt: use KMEM_CACHE macro
  [SCSI] initio: fix big endian problems for auto request sense
  ...
2008-04-18 11:25:31 -07:00
James Bottomley
855d854a33 libata: fix boot panic with SATAPI devices on non-SFF HBAs
The kernel now panics reliably on boot if you have a SATAPI device
connected.

The problem was introduced by the libata merge trying to pull out all
the SFF code into a separate module.  Unfortunately, if you're a satapi
device you usually need to call atapi_request_sense, which has a bare
invocation of a SFF callback which is NULL on non-SFF HBAs.  Fix this by
making the call conditional.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-18 11:20:42 -07:00
Shaohua Li
48feb3c419 ata-acpi: don't call _GTF for disabled drive
I got below log after a S3 resume in a ASUS A6VC laptop. The system has
only one IDE drive. It appears there is no reason calling _GTF for
disabled drive.

ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV0._GTF] (Node df822bd0), AE_AML_OPERAND_VALUE
ata2.00: _GTF evaluation failed (AE 0x3006)
ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV1._GTF] (Node df822b94), AE_AML_OPERAND_VALUE
ata2.01: _GTF evaluation failed (AE 0x3006)

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:29 -04:00
Mark Lord
094e50b2f7 sata_mv add temporary 3 second init delay for SiliconImage PMs
sata_mv does not yet fully support hotplug (coming soon, though).
This means that the driver may not find a Silicon Image port-multiplier
when first loaded, because those devices take in exceess of 3 seconds
to sync up the SATA PHY (most devices do this in mere microseconds).

So, as a short-term interim measure, here we insert a 3-second pause
on initial driver load, once per controller board (not once per port!),
to allow the Silicon Image port-multipliers to be detected later.

This will be removed again (soon!) once hotplug is fully implemented/working.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:25 -04:00
Mark Lord
8a74f1a468 sata_mv remove redundant edma init code
Remove unnecessary edma init code from port_start.
This sequence gets done later on the first I/O to the port.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:21 -04:00
Mark Lord
e49856d82a sata_mv add basic port multiplier support
Add basic port-multiplier support to sata_mv.
This works in Command-based-switching mode for Gen-II chipsets,
and in FIS-based-switching mode for Gen-IIe chipsets.

Error handling remains at the primary port level for now
(works okay, but not great).  This will get fixed in a subsequent
patch series for IRQ/EH handling fixes.  There are also some
known NCQ/PMP errata to be dealt with in the near future,
once we have this basic PMP support in place.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:19 -04:00
Mark Lord
02c1f32f1c sata_mv fix SOC flags, enable NCQ on SOC
The System-On-Chip (SOC) core supports all of the same
features as the other recent Marvell chips,
including NCQ and IRQ coalescing.

Fix the chip_soc flags to enable these capabilities
(note that the driver currently does nothing special
for IRQ coalescing, though).

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:16 -04:00
Mark Lord
40f0bc2d77 sata_mv disable hotplug for now
Disable hot plug/unplug detection in sata_mv for now.
It is currently broken, and also interferes with PMP support.

This will get fixed in a subsequent patch series.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:12 -04:00
Mark Lord
17c5aab5b3 sata_mv cosmetics
More cosmetic cleanups to unclutter the changes needed for PMP support.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:08 -04:00
Mark Lord
0d8be5cbff sata_mv hardreset rework
Rework and simplify sata_mv's hardreset code to take advantage of
libata improvements since it was first coded.

Also, get rid of the now unnecessary prereset, postreset, and phy_reset
functions.

This patch also paves the way for subsequent pmp support patches,
which will follow once this one passes muster.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:56:05 -04:00
Jeff Garzik
f3360ebffa [libata] improve Kconfig help text for new PMP, SFF options 2008-04-17 15:55:24 -04:00
Tejun Heo
4f7faa3f2b libata: make EH fail gracefully if no reset method is available
When no reset method is available, libata currently oopses.  Although
the condition can't happen unless there's a bug in a low level driver,
oopsing isn't the best way to report the error condition.  Complain,
dump stack and fail reset instead.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:26 -04:00
Alan Cox
b93fda1235 libata: Be a bit more slack about early devices
We have a certain number of 'ATA' emulations often on CF or other flash
devices that are at best "loosely based" on the CF 1.1 standard. These
devices report themselves as disk but don't support the ATA minimal
command set only the CF 1.1 set.

Relax the PIO checking for devices reporting ATA rev 0, or no iordy
support, or CFA. Rework the code a bit as it was already messy and this
made it quite ugly.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Alan Cox
f792068e43 libata: cable logic
The cable detect isolation patch inadvertently removed 40 wire short
cable handling. Put it back

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
45db2f6c95 libata: move link onlineness check out of softreset methods
Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.

This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.

sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset.  This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
2a0c15ca39 libata: kill dead code paths in reset path
Some code paths which had been made obsolete by recent reset
simplification were still around.  Kill them.

* ata_eh_reset() checked for ATA_DEV_UNKNOWN to determine
  classification failure.  This is no longer applicable.

* ata_do_reset() should convert ATA_DEV_UNKNOWN to ATA_DEV_NONE
  regardless of reset result (e.g. -EAGAIN).

* LLDs don't need to convert ATA_DEV_UNKNOWN to ATA_DEV_NONE.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Stephen Rothwell
e50e3ce5e7 pata_scc: fix build breakage
drivers/ata/pata_scc.c: In function 'scc_bus_softreset':
drivers/ata/pata_scc.c:594: error: 'deadlien' undeclared (first use in this function)
drivers/ata/pata_scc.c:594: error: (Each undeclared identifier is reported only once
drivers/ata/pata_scc.c:594: error: for each function it appears in.)

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:25 -04:00
Tejun Heo
88fcd56275 libata: make PMP support optional
Make PMP support optional by adding CONFIG_SATA_PMP and leaving out
libata-pmp.c if it isn't set.  PMP helpers return constant values if
PMP support is not enabled and PMP declarations alias non-PMP
counterparts.  This makes the compiler to leave out PMP related part
out and LLDs to use non-PMP counterparts automatically.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
071f44b1d2 libata: implement PMP helpers
Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link.  While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.

This change simplifies LLDs and helps making PMP support optional.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
48515f6c00 libata: separate PMP support code from core code
Most of PMP support code is already in libata-pmp.c.  All that are in
libata-core.c are sata_pmp_port_ops and EXPORTs.  Move them to
libata-pmp.c.  Also, collect PMP related prototypes and declarations
in header files and move them right above of SFF stuff.

This change is to make PMP support optional.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
127102aea2 libata: make SFF support optional
Now that SFF support is completely separated out from the core layer,
it can be made optional.  Add CONFIG_ATA_SFF and let SFF drivers
depend on it.  If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled.  This saves good
number of bytes for small systems.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
350756f6da libata: don't use ap->ioaddr in non-SFF drivers
ap->ioaddr is to carry addresses for TF and BMDMA registers of a SFF
controller, don't abuse it in non-SFF controllers.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
182d7bbac3 libata: clean up dummy port_ops
Now that SFF assumptions are removed from core layer, dummy port_ops
can be slimmed down.  Chop it down.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
c9f75b04ed libata: kill ata_noop_dev_select()
Now that SFF assumptions are separated out from non-SFF reset
sequence, port_ops->sff_dev_select() is no longer necessary for
non-SFF controllers.  Kill ata_noop_dev_select() and ->sff_dev_select
initialization from base and other non-SFF port_ops.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
520d06f92b libata: remove check_status from non-SFF drivers
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->[alt_]check_status().  In fact, no one calls them
for non-SFF drivers anymore.  Kill them.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo
4c9bf4e799 libata: replace tf_read with qc_fill_rtf for non-SFF drivers
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->tf_read directly.  It gets called only via
ops->qc_fill_rtf() for non-SFF drivers.  This patch directly
implements private ops->qc_fill_rtf() for non-SFF controllers and kill
ops->tf_read().

This is much cleaner for non-SFF controllers as some of them have to
cache SFF register values in private data structure and report the
cached values via ops->tf_read().  Also, ops->tf_read() gets nasty for
controllers which don't have clear notion of TF registers when
operation is not in progress.

As this change makes default ops->qc_fill_rtf unnecessary, move
ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where
it belongs.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
79f97dadfe libata: drop @finish_qc from ata_qc_complete_multiple()
ata_qc_complete_multiple() took @finish_qc and called it on every qc
before completing it.  This was to give opportunity to update TF cache
before ata_qc_complete() tries to fill result_tf.  Now that result TF
is a separate operation, this is no longer necessary.

Update sata_sil24, which was the only user of this mechanism, such
that it implements its own ops->qc_fill_rtf() and drop @finish_qc from
ata_qc_complete_multiple().

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
22183bf569 libata: add qc_fill_rtf port operation
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf.  This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.

ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.

ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes.  As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
305d2a1ab1 libata: unify mechanism to request follow-up SRST
Previously, there were two ways to trigger follow-up SRST from
hardreset method - returning -EAGAIN and leaving all device classes
unmodified.  Drivers never used the latter mechanism and the only use
case for the former was when hardreset couldn't classify.

Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST
if classification is required".  This change removes unnecessary
follow-up SRSTs and simplifies reset implementations.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
5958e3025f libata: move PMP SCR access failure during reset to ata_eh_reset()
If PMP fan-out reset fails and SCR isn't accessible, PMP should be
reset.  This used to be tested by sata_pmp_std_hardreset() and
communicated to EH by -ERESTART.  However, this logic is generic and
doesn't really have much to do with specific hardreset implementation.

This patch moves SCR access failure detection logic to ata_eh_reset()
where it belongs.  As this makes sata_pmp_std_hardreset() identical to
sata_std_hardreset(), the function is killed and replaced with the
standard method.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
ac371987a8 libata: clear SError after link resume
SError used to be cleared in ->postreset.  This has small hotplug race
condition.  If a device is plugged in after reset is complete but
postreset hasn't run yet, its hotplug event gets lost when SError is
cleared.  This patch makes sata_link_resume() clear SError.  This
kills the race condition and makes a lot of sense as some PMP and host
PHYs don't work properly without SError cleared.

This change makes sata_pmp_std_{pre|post}_reset()'s unnecessary as
they become identical to ata_std counterparts.  It also simplifies
sata_pmp_hardreset() and ahci_vt8251_hardreset().

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
57c9efdfb3 libata: implement and use sata_std_hardreset()
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset().  sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.

ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.

piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
9dadd45b24 libata: move generic hardreset code from sata_sff_hardreset() to sata_link_hardreset()
sata_sff_hardreset() contains link readiness wait logic which isn't
SFF specific.  Move that part into sata_link_hardreset(), which now
takes two more parameters - @online and @check_ready.  Both are
optional.  The former is out parameter for link onlineness after
reset.  The latter is used to wait for link readiness after hardreset.

Users of sata_link_hardreset() is updated to use new funtionality and
ahci_hardreset() is updated to use sata_link_hardreset() instead of
sata_sff_hardreset().  This doesn't really cause any behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
a89611e848 ahci: use ata_wait_after_reset() instead of ata_sff_wait_ready()
Implement ahci_check_ready() and replace ata_sff_wait_after_reset()
with ata_wait_after_reset().  As ahci was faking TF access, this
change doesn't result in any functional difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
aa2731ad9a libata: separate out ata_wait_ready() and implement ata_wait_after_reset()
Factor out waiting logic (which is common to all ATA controllers) from
ata_sff_wait_ready() into ata_wait_ready().  ata_wait_ready() takes
@check_ready function pointer and uses it to poll for readiness.  This
allows non-SFF controllers to use ata_wait_ready() to wait for link
readiness.

This patch also implements ata_wait_after_reset() - generic version of
ata_sff_wait_after_reset() - using ata_wait_ready().

ata_sff_wait_ready() is reimplemented using ata_wait_ready() and
ata_sff_check_ready().  Functionality remains the same.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
705e76beb9 libata: restructure SFF post-reset readiness waits
Previously, post-softreset readiness is waited as follows.

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
   If not, continue to #3.

3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
   on devmask using ata_sff_wait_ready().

And for post-hardreset readiness,

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. sata_sff_hardreset waits for device readiness using
   ata_sff_wait_ready().

This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().

ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready().  If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.

ata_sff_wait_after_reset() is updated to perform the following steps.

1. waits for 150ms.

2. waits for dev0 readiness using ata_sff_wait_ready().  Note that
   this is done regardless of devmask, as ata_sff_wait_ready() handles
   0xff status correctly, this preserves the original behavior except
   that it may wait longer after softreset if link is online but
   status is 0xff.  This behavior change is very unlikely to cause any
   actual difference and is intended.  It brings softreset behavior to
   that of hardreset.

3. waits for dev1 readiness just the same way ata_bus_post_reset() did.

Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets.  As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.

This change makes reset implementation simpler and more consistent.

While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap.  This is to make them consistent with other
reset helpers and ease core changes.

pata_scc is updated accordingly.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
203c75b824 libata: separate out ata_std_postreset() from ata_sff_postreset()
Separate out generic ATA portion from ata_sff_postreset() into
ata_std_postreset() and implement ata_sff_postreset() using the std
version.

ata_base_port_ops now has ata_std_postreset() for its postreset and
ata_sff_port_ops overrides it to ata_sff_postreset().

This change affects pdc_adma, ahci, sata_fsl and sata_sil24.  pdc_adma
now specifies postreset to ata_sff_postreset() explicitly.  sata_fsl
and sata_sil24 now use ata_std_postreset() which makes no difference
to them.  ahci now calls ata_std_postreset() from its own postreset
method, which causes no behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
0aa1113d54 libata: separate out ata_std_prereset() from ata_sff_prereset()
Separate out generic ATA portion from ata_sff_prereset() into
ata_std_prereset() and implement ata_sff_prereset() using the std
version.  Waiting for device readiness is the only SFF specific part.

ata_base_port_ops now has ata_std_prereset() for its prereset and
ata_sff_port_ops overrides it to ata_sff_prereset().  This change can
affect pdc_adma, ahci, sata_fsl and sata_sil24.  pdc_adma implements
its own prereset using ata_sff_prereset() and the rest has hardreset
and thus are unaffected by this change.

This change reflects real world situation.  There is no generic way to
wait for device readiness for non-SFF controllers and some of them
don't have any mechanism for that.  Non-sff drivers which don't have
hardreset should wrap ata_std_prereset() and wait for device readiness
itself but there's no such driver now and isn't likely to be popular
in the future either.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
288623a06c libata: clean up port_ops->sff_irq_clear()
->sff_irq_clear() is called only from SFF interrupt handler, so there
is no reason to initialize it for non-SFF controllers.  Also,
ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF
controllers.

This patch kills ata_noop_irq_clear() and removes it from base
port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff
port_ops instead of bmdma port_ops.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
5682ed33aa libata: rename SFF port ops
Add sff_ prefix to SFF specific port ops.

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames ops and doesn't introduce any
behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
9363c3825e libata: rename SFF functions
SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:21 -04:00
Mark Lord
b67a1064cb sata_mv fix ifctl handling
Fix handling of the SATA_INTERFACE_CFG register to match datasheet requirements.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Mark Lord
b562468cc3 sata_mv clean up mv_stop_edma usage
Clean up uses of mv_stop_edma{_engine}() to match datasheet requirements.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Mark Lord
e12bef50b7 sata_mv cosmetic fixes
Various cosmetic fixes in preparation for real code changes later on.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Chris Wedgwood
c30484d775 Add 'short help text' to ATA_ACPI so it's [de]selectable.
ATA_ACPI isn't selectable right now because it lacks 'short help
text'.  This means it's always enabled and always enables ACPI_DOCK.
Add text so it's now [de]selectable.

cc: Jeff Garzik <jeff@garzik.org>
cc: Tejun Heo <htejun@gmail.com>
cc: Len Brown <len.brown@intel.com>
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Tejun Heo
fc4712d12e pdc_adma: kill adma_host_stop()
adma_host_stop() does the same thing that adma_port_stop() does.  Kill
it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:21 -04:00
Tejun Heo
b0316b15ac pdc_adma: inherit ata_sff_port_ops
With the previous ops standardization, pdc_adma now can inherit
ata_sff_port_ops instead of ata_base_port_ops.  Make the change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
ed82f96425 libata/pdc_adma: make SFF EH handle non-bmdma SFF drivers and standardize pdc_adma ops
pdc_adma has interface similar to SFF but has its own DMA interface.
It currently implements noop bmdma ops to avoid crashing
ata_bmdma_error_handler() which BTW actually is EH for SFF drivers.

This patch makes ata_bmdma_error_handler() dereference bmdma ops iff
bmdma_addr is initialized as done in ata_bmdma_post_internal_cmd.
This change allows pdc_adma to standardize ops and use SFF
error_handler and post_internal_cmd.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
d8b81b8008 libata: kill unused ata_flush_cache()
ata_flush_code() hasn't been in use for quite some time now.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
03faab7827 libata: implement ATA_QCFLAG_RETRY
Currently whether a command should be retried after failure is
determined inside ata_eh_finish().  Add ATA_QCFLAG_RETRY and move the
logic into ata_eh_autopsy().  This makes things clearer and helps
extending retry determination logic.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
a5987e0a1b libata: make ata_tf_to_lba[48]() generic
ata_tf_to_lba[48]() currently return LBA in tf + 1 for
ata_read_native_max_address().  Make them return LBA and make it
global so that it can be used to read LBA off TF for other purposes.
ata_read_native_max_address() now adds 1 itself.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Jeff Garzik
06993d2237 [libata] sata_nv: disable ADMA by default
Continues to have open issues, and engineering support is extremely difficult
to come by, according to fellow NVIDIA engineers.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:20 -04:00
Al Viro
826cd156de libata annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
9c0bf67505 ata_piix: kill ich6_sata_ahci and clean up
ich6_sata_ahci and ich6_sata are identical.  Kill ich6_sata_ahci and
drop _ahci postfixes from controller ids, which doesn't really mean
anything at this point.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
5016d7d212 ata_piix: don't attach to ICH6M in ahci mode
ata_piix when attached to ICH6M in AHCI mode doesn't provide any
benefit over using ahci and has detection problems.  Don't let
ata_piix claim ICH6M if it's in AHCI mode.

This change makes ICH6R the only one which ata_piix can attach to even
when it's in ahci mode which is necessary as some devices don't work
properly under ahci mode.  Drop PIIX_FLAG_AHCI and match the
controller directly so that piix_disable_ahci() is called only for it.

This change makes PIIX_SCC no longer used and it gets dropped too.

This fixes bz 9491.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robert M. Albrecht <romal@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:19 -04:00
Tejun Heo
c1796d9850 pata_scc: fix compile warning
Missed one during mass conversion (dc14c0c5).  Fix it.  Spotted by
Stephen Rothwell.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:19 -04:00
Alan Cox
15a5551c84 libata: isolate and rework cable logic
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:19 -04:00
Zoltan Boszormenyi
d21279f412 ata: SWNCQ should be enabled by default
Signed-off-by: Zoltan Boszormenyi <zboszor@dunaweb.hu>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:19 -04:00
Harvey Harrison
d9c74fbead pata_amd: fix sparse warning
Current code is essentially choosing between dividing by 1 or
dividing by two, make the conditions a little more obvious.

As a bonus, removes a sparse error:
drivers/ata/pata_amd.c:59:11: warning: symbol '__x' shadows an earlier one
drivers/ata/pata_amd.c:59:11: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
6fd3639011 libata: kill ata_chk_status()
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
3d5a3d67a5 libata: kill ata_chk_status() call from ata_dev_configure()
ata_dev_configure() isn't tied to any controller interface except for
the probe debug message printing at the end of the function.  Kill the
message.

This is to help separating out SFF support from core layer.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
071ce34d57 libata: move ata_pci_default_filter() out of CONFIG_PCI
ata_pci_default_filter() doesn't really have anything to do with PCI.
It's generally applicable to BMDMA controllers.  Move it out of
CONFIG_PCI.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
624d5c514e libata: reorganize SFF related stuff
* Move SFF related functions from libata-core.c to libata-sff.c.

  ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
  ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
  ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
  ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
  sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
  ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
  ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
  atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
  ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
  ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
  ata_interrupt(), ata_std_ports()

* Make ata_pio_queue_task() global as it's now called from
  libata-sff.c.

* Move SFF related stuff in include/linux/libata.h and
  drivers/ata/libata.h into one place.  While at it, move timing
  constants into the global enum definition and fortify comments a
  bit.

This patch strictly moves stuff around and as such doesn't cause any
functional difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
272f7884e8 libata: reorder functions in libata-sff.c
Reorder functions in drivers/ata/libata-sff.c such that functions
generally follow ops table order and init functions come last.  This
is in preparation of SFF cleanup.

This patch strictly moves stuff around and as such doesn't cause any
functional difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
21572ea58a libata: drop ata_dev_select() from ata_dev_read_id
There is no reason to issue device select in read_id, it will be done
by ops->qc_issue() when IDENTIFY[_PACKET] is issued via
ata_exec_internal().

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
a1efdaba2d libata: make reset related methods proper port operations
Currently reset methods are not specified directly in the
ata_port_operations table.  If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods.  It's done this way for two reasons.

First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.

Second, as ->error_handler uses those reset methods, it can get
confusing.  ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.

Now that ops table uses inheritance, the first problem doesn't exist
anymore.  The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks.  In fact, there currently is no driver which actually
modifies error handling behavior.  Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH.  I don't think making ops layering strict has
any noticeable benefit.

This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops.  Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.

* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
  aren't accessible.  sata_promise doesn't need to use separate
  error_handlers for PATA and SATA anymore.

* softreset is broken for sata_inic162x and sata_sx4.  As libata now
  always prefers hardreset, this doesn't really matter but the ops are
  forced to NULL using ATA_OP_NULL for documentation purpose.

* pata_hpt374 needs to use different prereset for the first and second
  PCI functions.  This used to be done by branching from
  hpt374_error_handler().  The proper way to do this is to use
  separate ops and port_info tables for each function.  Converted.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:18 -04:00
Tejun Heo
9594719362 libata: kill port_info->sht and ->irq_handler
libata core layer doesn't care about sht or ->irq_handler.  Those are
only of interest to the LLD during initialization.  This is confusing
and has caused several drivers to have duplicate unused initializers
for these fields.

Currently only sata_nv uses these fields.  Make sata_nv use
->private_data, which is supposed to carry LLD-specific information,
instead and kill ->sht and ->irq_handler.  nv_pi_priv structure is
defined and struct literals are used to initialize private_data.
Notational overhead is negligible.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
887125e374 libata: stop overloading port_info->private_data
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.

This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data.  In addition, port_info and host don't correspond
to each other 1-to-1.  Currently, the first non-NULL
port_info->private_data is used.

This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead.  LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data.  LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.

Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
2008-04-17 15:44:17 -04:00
Tejun Heo
1bd5b715a3 libata: make ata_pci_init_one() not use ops->irq_handler and pi->sht
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht.  Other initialization functions take the same information
as arguments.  This causes confusion and duplicate unused entries in
structures.

Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly.  All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.

As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
029cfd6b74 libata: implement and use ops inheritance
libata lets low level drivers build ata_port_operations table and
register it with libata core layer.  This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.

This becomes worse for drivers which support related similar
controllers which differ slightly.  They share most of the operations
except for a few.  However, the driver still needs to list all
operations for each variant.  This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.

This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone.  When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time.  Some of those inconsistencies
cause immediate problems and fixed.  Others just remain there dormant
making maintenance increasingly difficult.

To rectify the problem, this patch implements ata_port_operations
inheritance.  To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance.  An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop.  When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified.  This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.

libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma.  To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.

After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to.  The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.

* sata_sx4 is still using old style EH and currently doesn't take
  advantage of ops inheritance.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
68d1d07b51 libata: implement and use SHT initializers
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer.  This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.

This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht.  Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.

All sht tables are identical before and after this patch.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
6bd99b4e09 libata: normalize port_info, port_operations and sht tables
Over the time, port info, ops and sht structures developed quite a bit
of inconsistencies.  This patch updates drivers.

* Enable/disable_pm callbacks added to all ahci ops tables.

* Every driver for SFF controllers now uses ata_sff_port_start()
  instead of ata_port_start() unless the driver has custom
  implementation.

* Every driver for SFF controllers now uses ata_pci_default_filter()
  unless the driver has custom implementation.

* Removed an odd port_info->sht initialization from ata_piix.c.
  Likely a merge byproduct.

* A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
  to ata_cable_sata().  Remove it from via and mv port ops.

* Some drivers had unnecessary .max_sectors initialization which is
  ignored and was missing .slave_destroy callback.  Fixed.

* Removed unnecessary sht initializations port_info's.

* Removed onsolete scsi device suspend/resume callbacks from
  pata_bf54x.

* No reason to set ata_pci_default_filter() and bmdma functions for
  PIO-only drivers.  Remove those callbacks and replace
  ata_bmdma_irq_clear with ata_noop_irq_clear.

* pata_platform sets port_start to ata_dummy_ret0.  port_start can
  just be set to NULL.

* sata_fsl supports NCQ but was missing qc_defer.  Fixed.

* pata_rb600_cf implements dummy port_start.  Removed.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
358f9a77a6 libata: implement and use ata_noop_irq_clear()
->irq_clear() is used to clear IRQ bit of a SFF controller and isn't
useful for drivers which don't use libata SFF HSM implementation.
However, it's a required callback and many drivers implement their own
noop version as placeholder.  This patch implements ata_noop_irq_clear
and use it to replace those custom placeholders.

Also, SFF drivers which don't support BMDMA don't need to use
ata_bmdma_irq_clear().  It becomes noop if BMDMA address isn't
initialized.  Convert them to use ata_noop_irq_clear().

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
f08048e945 libata: PCI device should be powered up before being accessed
PCI device should be powered up or powered up before its PCI regsiters
are accessed.  Although PCI configuration register access is allowed
in D3hot, PCI device is free to reset its status when transiting from
D3hot to D0 causing configuration data to change.

Many libata SFF drivers which use ata_pci_init_one() read and update
configuration registers before calling ata_pci_init_one() which
enables the PCI device.  Also, in resume paths, some drivers access
registers without resuming the PCI device.

This patch adds a call to pcim_enable_device() in init path if
register is accessed before calling ata_pci_init_one() and make resume
paths first resume PCI devices, access PCI configuration regiters then
resume ATA host.

While at it...

* cmd640 was strange in that it set ->resume even when CONFIG_PM is
  not.  This is by-product of minimal build fix.  Updated.

* In cs5530, Don't BUG() on reinit failure.  Just whine and fail
  resume.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
b558edddb1 libata: kill ata_ehi_schedule_probe()
ata_ehi_schedule_probe() was created to hide details of link-resuming
reset magic.  Now that all the softreset workarounds are gone,
scheduling probe is very simple - set probe_mask and request RESET.
Kill ata_ehi_schedule_probe() and open code it.  This also increases
consistency as ata_ehi_schedule_probe() couldn't cover individual
device probings so they were open-coded even when the helper existed.

While at it, define ATA_ALL_DEVICES as mask of all possible devices on
a link and always use it when requesting probe on link level for
simplicity and consistency.  Setting extra bits in the probe_mask
doesn't hurt anybody.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
8cebf274dd libata: kill ATA_LFLAG_SKIP_D2H_BSY
Some controllers can't reliably record the initial D2H FIS after SATA
link is brought online for whatever reason.  Advanced controllers
which don't have traditional TF register based interface often have
this problem as they don't really have the TF registers to update
while the controller and link are being initialized.

SKIP_D2H_BSY works around the problem by skipping the wait for device
readiness before issuing SRST, so for such controllers libata issues
SRST blindly and hopes for the best.

Now that libata defaults to hardreset, this workaround is no longer
necessary.  For controllers which have support for hardreset, SRST is
never issued by itself.  It is only issued as follow-up SRST for
device classification and PMP initialization, so there's no need to
wait for it from prereset.

Kill ATA_LFLAG_SKIP_D2H_BSY.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
672b2d65ba libata: kill ATA_EHI_RESUME_LINK
ATA_EHI_RESUME_LINK has two functions - promote reset to hardreset if
ATA_LFLAG_HRST_TO_RESUME is set and preventing EH from shortcutting
reset action when probing is requested.  The former is gone now and
the latter can easily be achieved by making EH to perform at least one
reset if reset is requested, which also makes more sense than
depending on RESUME_LINK flag.

As ATA_EHI_RESUME_LINK was the only EHI reset modifier, this also
kills reset modifier handling.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
d692abd92f libata: kill ATA_LFLAG_HRST_TO_RESUME
Now that hardreset is the preferred method of resetting, there's no
need for ATA_LFLAG_HRST_TO_RESUME flag.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:15 -04:00
Tejun Heo
cf48062658 libata: prefer hardreset
When both soft and hard resets are available, libata preferred
softreset till now.  The logic behind it was to be softer to devices;
however, this doesn't really help much.  Rationales for the change:

* BIOS may freeze lock certain things during boot and softreset can't
  unlock those.  This by itself is okay but during operation PHY event
  or other error conditions can trigger hardreset and the device may
  end up with different configuration.

  For example, after a hardreset, previously unlockable HPA can be
  unlocked resulting in different device size and thus revalidation
  failure.  Similar condition can occur during or after resume.

* Certain ATAPI devices require hardreset to recover after certain
  error conditions.  On PATA, this is done by issuing the DEVICE RESET
  command.  On SATA, COMRESET has equivalent effect.  The problem is
  that DEVICE RESET needs its own execution protocol.

  For SFF controllers with bare TF access, it can be easily
  implemented but more advanced controllers (e.g. ahci and sata_sil24)
  require specialized implementations.  Simply using hardreset solves
  the problem nicely.

* COMRESET initialization sequence is the norm in SATA land and many
  SATA devices don't work properly if only SRST is used.  For example,
  some PMPs behave this way and libata works around by always issuing
  hardreset if the host supports PMP.

  Like the above example, libata has developed a number of mechanisms
  aiming to promote softreset to hardreset if softreset is not going
  to work.  This approach is time consuming and error prone.

  Also, note that, dependingon how you read the specs, it could be
  argued that PMP fan-out ports require COMRESET to start operation.
  In fact, all the PMPs on the market except one don't work properly
  if COMRESET is not issued to fan-out ports after PMP reset.

* COMRESET is an integral part of SATA connection and any working
  device should be able to handle COMRESET properly.  After all, it's
  the way to signal hardreset during reboot.  This is the most used
  and recommended (at least by the ahci spec) method of resetting
  devices.

So, this patch makes libata prefer hardreset over softreset by making
the following changes.

* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
  ATA_EH_{SOFT|HARD}RESET used to be used.  ATA_EH_{SOFT|HARD}RESET is
  now only used to tell prereset whether soft or hard reset will be
  issued.

* Strip out now unneeded promote-to-hardreset logics from
  ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
  other places.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:15 -04:00
Adrian Bunk
1892225f78 [libata] make ali_atapi_dma static
This patch makes the needlessly global ali_atapi_dma static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-12 00:16:49 -04:00
Jeff Garzik
aeb74914ef [libata] sata_svw: fix reversed port count
According to Broadcom, two chips have their port counts flipped.  The proper
count is:

0x241 is 8 ports
0x242 is 4 ports

Reported by Yohei Honda on kernel bz 10424.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-12 00:11:35 -04:00
Johann Felix Soden
ac2c5bd05c ata/sata_fsl: Remove unused variable in sata_fsl_probe
In sata_fsl_probe memory is allocated but never used or deallocated.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=10404

Thanks to Daniel Marjamäki for the bug report.

Reported-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-09 01:06:37 -04:00
Benjamin Herrenschmidt
119b3aa65d pata_sil680: Fix build on arch/ppc
Commit 0f436eff54 breaks build on
arch/ppc as it doesn't implement the machine_is() macro.

This fixes it by using CONFIG_PPC_MERGE instead which represents
arch/powerpc only, while CONFIG_PPC is set for both.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-09 01:06:33 -04:00
FUJITA Tomonori
526917641a [SCSI] libata: use scsi_build_sense_buffer
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-07 12:19:02 -05:00
Tejun Heo
8243e636c0 pata_ali: disable ATAPI DMA
ATAPI DMA just doesn't work reliably on pata_ali.  The IDE driver can
do it but for some mysterious reason, pata_ali can't.  This patch
disables it by default and makes the driver whine during
initialization.  "pata_ali.atapi_dma" parameter is added so that user
can bypass the workaround.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-04 02:43:38 -04:00
Tejun Heo
e52dcc4899 libata: ATA_12/16 doesn't fall into ATAPI_MISC
SAT passthrus don't really fit into ATAPI_MISC class.  SAT passthru
commands always transfer multiple of 512 bytes and variable length
response is not allowed.  This patch creates a separate category -
ATAPI_PASS_THRU - for these.

This fixes HSM violation on "hdparm -I".

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-04 02:43:36 -04:00
Tejun Heo
436d34b362 libata: uninline atapi_cmd_type()
Uninline atapi_cmd_type().  It doesn't really have to be inline and
more case will be added which need to access unexported libata
variable.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-04 02:43:35 -04:00
Bartlomiej Zolnierkiewicz
a4ba7fe2a6 libata: fix IDENTIFY order in ata_bus_probe()
Commit f58229f806 accidentally made
ata_bus_probe() not use reverse order probing.  Fix it.

There currently isn't any PATA driver which uses obsolete
ata_bus_probe() path, so this patch is mainly for correctness.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-04 02:43:33 -04:00
Kim Phillips
96ce1b6dc5 [POWERPC] sata_fsl: reduce compatibility to fsl,pq-sata
as prescribed in Documentation/powerpc/booting-without-of.txt.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-31 10:27:35 -05:00
Tejun Heo
3ec25ebd69 libata: ATA_EHI_LPM should be ATA_EH_LPM
EH actions are ATA_EH_* not ATA_EHI_*.  Rename ATA_EHI_LPM to
ATA_EH_LPM.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-29 12:21:31 -04:00
Benjamin Herrenschmidt
0f436eff54 pata_sil680: only enable MMIO on Cell blades
There have been reported regressions of the SIL 680 driver when using MMIO, so
this makes it only try MMIO on Cell blades where it's known to be necessary
(the host bridge doesn't do PIO on these).

We'll try to find the root problem with MMIO separately.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-29 12:21:27 -04:00
Lennert Buytenhek
15a32632d9 sata_mv: mbus decode window support
Make it possible to pass mbus_dram_target_info to the sata_mv
driver via the platform data, make the sata_mv driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the SATA mbus window registers by hand.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
2008-03-27 14:51:39 -04:00
Jeff Garzik
4cde32fc4b [libata] ahci: SB600 workaround is suspect... play it safe for now
At least one report claims that a878539ef9
failed to solve lockups, whereas the old limit-to-32-bit trick worked.

Restore the 32-bit limit, but also leave the 255-sector limit in place,
because we know that's needed as well.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-03-24 22:40:40 -04:00
Mikael Pettersson
c07a9c4995 sata_promise: fix hardreset hotplug events, take 2
A Promise SATA controller will signal hotplug events when a hard
reset (COMRESET) is done on a port. These events aren't masked by
the driver, and the unexpected interrupts will cause a sequence
of failed reset attempts util libata's EH finally gives up.

This has not been a common problem so far, but the pending libata
hardreset-by-default changes makes it a critical issue.

The solution is to disable hotplug events before a reset, and to
reenable them afterwards. (Promise's driver does this too.)

This patch adds SATA-specific versions of ->freeze() and ->thaw()
that also disable and enable hotplug events. PATA ports continue
to use the old versions of ->freeze() and ->thaw().

Accesses to the hotplug register must be serialised via host->lock.
We rely on ap->lock == &ap->host->lock and that libata takes this
lock before ->freeze() and ->thaw(). Document this requirement.
The interrupt handler is adjusted so its hotplug register accesses
are inside the region protected by host->lock.

Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4,
FastTrack TX4000) with various combinations of SATA and PATA disks,
with and without the pending hardreset-by-default changes.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-24 22:31:25 -04:00
Tejun Heo
dda7aba119 libata: improve HPA error handling
There's no point in retrying and eventually failing device detection
when the device rejects READ_NATIVE_MAX[_EXT].  Disable HPA unlocking
if READ_NATIVE_MAX[_EXT] is rejected as done when SET_MAX[_EXT] is
rejected.

This allows some old drives to work even if they aren't blacklisted.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-24 22:09:40 -04:00
Tejun Heo
1ffc151fcd libata: assume no device is attached if both IDENTIFYs are aborted
This is to fix bugzilla #10254.  QSI cdrom attached to pata_sis as
secondary master appears as phantom device for the slave.
Interestingly, instead of not setting DRQ after IDENTIFY which
triggers NODEV_HINT, it aborts both IDENTIFY and IDENTIFY PACKET which
makes EH retry.

Modify EH such that it assumes no device is attached if both flavors
of IDENTIFY are aborted by the device.  There really isn't much point
in retrying when the device actively aborts the commands.

While at it, convert NODEV detection message to ata_dev_printk() to
help debugging obscure detection problems.

This problem was reported by Jan Bücken.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jan Bücken <jb.faq@gmx.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-24 22:09:38 -04:00
Tejun Heo
b63b133165 pata_it821x: use raw nbytes in check_atapi_dma
pata_it821x needs to look at raw request size in check_atapi_dma().

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-24 22:09:24 -04:00
Tejun Heo
aacda37538 libata: implement ata_qc_raw_nbytes()
Implement ata_qc_raw_nbytes() which determines the raw user-requested
size of a PC command.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-24 22:09:12 -04:00
Len Brown
0ac4a3c2fb ACPI: fix ATA_ACPI build
drivers/ata/libata-acpi.c fails to build

drivers/built-in.o: In function `ata_acpi_associate':
(.text+0x7106a): undefined reference to `register_hotplug_dock_device'

When CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m
But if dock is selected from ata_acpi, dock will =y
when ata_acpi=y, avoiding this problem.

http://bugzilla.kernel.org/show_bug.cgi?id=10272

Signed-off-by: Len Brown <len.brown@intel.com>
2008-03-18 00:26:07 -04:00
Jose Alberto Reguero
c40e7cb89f ahci: Add Marvell 6121 SATA support
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17 08:30:32 -04:00
Tejun Heo
4a38e733a7 pata_ali: use atapi_cmd_type() to determine cmd type instead of transfer size
pata_ali was using qc->nbytes to determine whether a command is
data transfer type or not.  As now qc->nbytes can be extended by
padding and draining buffers, these tests are not useful anymore.

Use atapi_cmd_type() instead.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17 08:26:52 -04:00
Tejun Heo
a22e64443f ahci: implement skip_host_reset parameter
Under certain circumstances (SSP turned off by the BIOS) and for
debugging purposes, skipping global controller reset is helpful.  Add
a kernel parameter for it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17 08:26:50 -04:00
Tejun Heo
dea5513763 ahci: request all PCI BARs
ahci is often implemented with accompanying SFF compatible interface
and legacy IDE driver may attach to the legacy IO ports when the
controller is already claimed by ahci and vice-versa.  This patch
makes ahci use pcim_iomap_regions_request_all() so that all IO regions
are claimed on attach.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17 08:26:47 -04:00
Tejun Heo
233f112042 libata-acpi: improve dock event handling
Improve ACPI hotplug handling such that dock event is handled properly.

* Register handlers for dock events.

* Directly detach device on EJECT_REQUEST instead of signaling hotplug
  event.  This prevents libata from accessing severed controller
  and/or device.

* While at it, use named constants for ACPI events and move uevent
  signaling inside host lock.

Original patch and testing by Holger Macht.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17 08:26:42 -04:00
Florian Fainelli
3db691daa4 [libata] Add support for the RB500 PATA CompactFlash
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:54:05 -04:00
Roel Kluin
258cd8464b ahci: logical-bitwise and confusion in ahci_save_initial_config()
logical-bitwise & confusion

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:51:16 -04:00
Tejun Heo
7afb42226a libata: don't allow sysfs read access to force param
Buffer for force param is deallocated after initialization, so trying
to read it via sysfs results in oops.  Don't allow read access to the
param node.

Spotted by Eric Sesterhenn.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:51:05 -04:00
peerchen
70d562cf78 ahci: add the Device IDs for nvidia MCP7B AHCI
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:50:52 -04:00
Tejun Heo
f659f0e448 libata-sff: handle controllers w/o ctl register
SFF incorrectly assumed that ctl register is available for all
controllers while some old SFF controllers don't have ctl register.
Make SFF handle controllers w/o ctl register by conditionalizing ctl
register access and softreset method.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:50:36 -04:00
Tejun Heo
eec59f76e9 libata: allow LLDs w/o any reset method
Some old SFF controllers don't have any way to reset the channel.
Currently, this isn't supported and libata EH causes an oops.  Allow
LLDs w/o any reset method and just assume ATA class in such cases.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:50:34 -04:00
Harvey Harrison
7f5e4e8d94 ata: replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:50:31 -04:00
Jeff Garzik
a878539ef9 ahci: work around ATI SB600 h/w quirk
This addresses the recent ATI SB600 errata, where the hardware does
not like 256-length PRD entries during FPDMA (aka NCQ).

It hurts performance on SB600, but it is more important to get a
correct patch eliminating the data corruption/lockups, and then later
on tune for performance.

We simply limit each command to a maximum of 255 sectors, on SB600.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-03-05 07:53:06 -05:00
Alan Cox
6ddd68615a pata_hpt*, pata_serverworks: fix UDMA masking
When masking, mask out the modes that are unsupported not the ones
that are supported.  This makes life happier.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-05 07:46:34 -05:00
Tejun Heo
e3790c7d42 block: separate out padding from alignment
Block layer alignment was used for two different purposes - memory
alignment and padding.  This causes problems in lower layers because
drivers which only require memory alignment ends up with adjusted
rq->data_len.  Separate out padding such that padding occurs iff
driver explicitly requests it.

Tomo: restorethe code to update bio in blk_rq_map_user
      introduced by the commit 40b01b9bbd
      according to padding alignment.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-03-04 11:18:17 +01:00
FUJITA Tomonori
7a85f8896f block: restore the meaning of rq->data_len to the true data length
The meaning of rq->data_len was changed to the length of an allocated
buffer from the true data length. It breaks SG_IO friends and
bsg. This patch restores the meaning of rq->data_len to the true data
length and adds rq->extra_len to store an extended length (due to
drain buffer and padding).

This patch also removes the code to update bio in blk_rq_map_user
introduced by the commit 40b01b9bbd.
The commit adjusts bio according to memory alignment
(queue_dma_alignment). However, memory alignment is NOT padding
alignment. This adjustment also breaks SG_IO friends and bsg. Padding
alignment needs to be fixed in a proper way (by a separate patch).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
2008-03-04 11:17:11 +01:00
Jeff Garzik
b445c56815 [libata] wrap kmap_atomic(KM_IRQ0) with local_irq_save/restore()
Interrupts must be disabled if using kmap_atomic(KM_IRQ0), but that was
not the case in a few code paths coming directly from ATA driver
interrupt handlers (which use spin_lock rather than spin_lock_irqsave).

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-02-29 19:10:51 -05:00
Anantha Subramanyam
931506d3b2 sata_svw: Add support for HT1100 SATA controller
This patch adds support (including ATAPI DMA) for HT1100 (aka BCM11000) SATA controller.

Signed-off-by: Anantha Subramanyam <ananth@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-28 19:02:29 -05:00
Jeff Garzik
72ad6ec489 Revert "power_state: get rid of write-only variable in SATA"
This reverts commit 559bbe6cbd.

Michael S. Tsirkin reports that this changes breaks suspend/resume.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-02-25 17:31:10 -05:00
Adrian Bunk
c5c61bda5e make atapi_dmadir static
atapi_dmadir can now become static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-25 17:29:35 -05:00
Randy Dunlap
4cdfa1b3ce libata-core: fix kernel-doc warning
Fix libata-core kernel-doc warning:
Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24 00:28:48 -05:00
Anton Vorontsov
b1f5dc48e2 sata_fsl: fix build with ATA_VERBOSE_DEBUG
This patch fixes build and few warnings when ATA_VERBOSE_DEBUG
is defined:

  CC      drivers/ata/sata_fsl.o
drivers/ata/sata_fsl.c: In function ‘sata_fsl_fill_sg’:
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 3 has type ‘void *’
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 4 has type ‘struct prde *’
drivers/ata/sata_fsl.c: In function ‘sata_fsl_qc_issue’:
drivers/ata/sata_fsl.c:459: error: ‘csr_base’ undeclared (first use in this function)
drivers/ata/sata_fsl.c:459: error: (Each undeclared identifier is reported only once
drivers/ata/sata_fsl.c:459: error: for each function it appears in.)
drivers/ata/sata_fsl.c: In function ‘sata_fsl_freeze’:
drivers/ata/sata_fsl.c:525: error: ‘csr_base’ undeclared (first use in this function)
make[2]: *** [drivers/ata/sata_fsl.o] Error 1

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24 00:28:46 -05:00
Shane Huang
e39fc8c9fd [libata] ahci: AMD SB700/SB800 SATA support 64bit DMA
SB700 SATA controller can support 64 bit DMA, the previous commit
badc234157 was added with
careless reference to SB600, which should be modified by this patch.

Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24 00:28:44 -05:00
Mark Lord
39f25e70ca libata-pmp: clear hob for pmp register accesses
>> Mark Lord wrote:
>>> Tejun, I've added PMP to sata_mv, and am now trying to get it
>>> to work with a Marvell PM attached.
>>>
>>> And the behaviour I see is very bizarre.
>>>
>>> After hard+soft resets, the PM signature is found,
>>> and libata interrogates the PM registers.
>>>
>>> It successfully reads register 0, and then register 1.
>>> But all subsequent registers read out (incorrectly) as zeros.
...

This behavior has been confirmed by Marvell with a SATA analyzer.
The Marvell port-multiplier apparently likes to see clean HOB
information when accessing PMP registers.

Since sata_mv uses PIO shadow register access, this doesn't happen
automatically, as it might in a more purely FIS-based driver (eg. ahci).

One way to fix this is to flag these commands with ATA_TFLAG_LBA48,
forcing libata to write out the HOB fields with known (zero) values.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24 00:28:23 -05:00
Tejun Heo
9116300634 libata: automatically use DMADIR if drive/bridge requires it
Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.

That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).

So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.

This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.

Original patch is from Mark Lord.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24 00:27:33 -05:00
Pavel Machek
559bbe6cbd power_state: get rid of write-only variable in SATA
power_state is scheduled for removal, and libata uses it in write-only
mode. Remove it.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24 00:27:26 -05:00
Alan Cox
635adc2808 pata_atiixp: Use 255 sector limit
AHCI needs sorting too but this deals with the old interface

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24 00:27:23 -05:00
Rafael J. Wysocki
3a2d5b7001 PM: Introduce PM_EVENT_HIBERNATE callback state
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.

But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.

For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate.  Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.

These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-23 10:40:04 -08:00
Randy Dunlap
73fd8b6d31 libata: fix kernel-doc parameter warning
Fix libata kernel-doc parameter:

Warning(linux-2.6.25-rc2-git3//drivers/ata/libata-scsi.c:845): No description found for parameter 'rq'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-20 12:20:49 -05:00
Saeed Bishara
f1cb0ea12f sata_mv: remove iounmap in mv_platform_remove and use devm_iomap
this will fix crash bug when doing rmmod to the driver, this is because the
port_stop function get called later and it could access the device's registers.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-20 12:20:46 -05:00
Tejun Heo
3326732570 libata: implement libata.force module parameter
This patch implements libata.force module parameter which can
selectively override ATA port, link and device configurations
including cable type, SATA PHY SPD limit, transfer mode and NCQ.

For example, you can say "use 1.5Gbps for all fan-out ports attached
to the second port but allow 3.0Gbps for the PMP device itself, oh,
the device attached to the third fan-out port chokes on NCQ and
shouldn't go over UDMA4" by the following.

 libata.force=2:1.5g,2.15:3.0g,2.03:noncq,udma4

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-20 12:12:28 -05:00
Saeed Bishara
0fca0d6f2c sata_mv: use hpriv->base instead of the host->iomap
this fixes crash bug as the iomap table is not valid for integrated controllers.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-20 12:09:17 -05:00
Martin Michlmayr
2e7e1214de sata_mv: Define module alias for platform device
The sata_mv driver can be loaded as a platform device, as is done by
various Orion (ARM) based devices.  The driver needs to define a module
alias for the platform driver so udev will load it automatically.
Tested with Debian on a QNAP TS-209.

Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-20 12:08:54 -05:00
Harvey Harrison
cb616dd5bb ata: fix sparse warnings in pata_legacy.c
Use ld_qdi and ld_winbond to avoid shadowing static int
variables qdi and winbond.  The ld_ prefix refers to
legacy_data.

drivers/ata/pata_legacy.c:777:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:811:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:848:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:882:21: warning: symbol 'qdi' shadows an earlier one
drivers/ata/pata_legacy.c:128:12: originally declared here
drivers/ata/pata_legacy.c:1040:21: warning: symbol 'winbond' shadows an earlier one
drivers/ata/pata_legacy.c:129:12: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-20 12:08:15 -05:00
James Bottomley
fa2fc7f481 libata: implement drain buffers
This just updates the libata slave configure routine to take advantage
of the block layer drain buffers.  It also adjusts the size lengths in
the atapi code to add the drain buffer to the DMA length so the driver
knows it can rely on it.

I suspect I should also be checking for AHCI as well as ATA_DEV_ATAPI,
but I couldn't see how to do that easily.

tj: * atapi_drain_needed() added such that draining is applied to only
      misc ATAPI commands.
    * q->bounce_gfp used when allocating drain buffer.
    * Now duplicate ATAPI PIO drain logic dropped.
    * ata_dev_printk() used instead of sdev_printk().

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-02-19 11:36:57 +01:00
James Bottomley
dde2020754 libata: eliminate the home grown dma padding in favour of
that provided by the block layer

ATA requires that all DMA transfers begin and end on word boundaries.
Because of this, a large amount of machinery grew up in ide to adjust
scatterlists on this basis.  However, as of 2.5, the block layer has a
dma_alignment variable which ensures both the beginning and length of a
DMA transfer are aligned on the dma_alignment boundary.  Although the
block layer does adjust the beginning of the transfer to ensure this
happens, it doesn't actually adjust the length, it merely makes sure
that space is allocated for transfers beyond the declared length.  The
upshot of this is that scatterlists may be padded to any size between
the actual length and the length adjusted to the dma_alignment safely
knowing that memory is allocated in this region.

Right at the moment, SCSI takes the default dma_aligment which is on a
512 byte boundary.  Note that this aligment only applies to transfers
coming in from user space.  However, since all kernel allocations are
automatically aligned on a minimum of 32 byte boundaries, it is safe to
adjust them in this manner as well.

tj: * Adjusting sg after padding is done in block layer.  Make libata
      set queue alignment correctly for ATAPI devices and drop broken
      sg mangling from ata_sg_setup().
    * Use request->raw_data_len for ATAPI transfer chunk size.
    * Killed qc->raw_nbytes.
    * Separated out killing qc->n_iter.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-02-19 11:36:56 +01:00
Tejun Heo
56c819df77 libata: update ATAPI overflow draining
For misc ATAPI commands which transfer variable length data to the
host, overflow can occur due to application or hardware bug.  Such
overflows can be ignored safely as long as overflow data is properly
drained.  libata HSM implementation has this implemented in
__atapi_pio_bytes() and recently updated for 2.6.24-rc but it requires
further improvements.  Improve drain logic such that...

* Report overflow errors using ehi desc mechanism instead of printing
  directly.

* Properly calculate the number of bytes to be drained considering
  actual number of consumed bytes for partial draining.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-02-19 11:35:37 +01:00
Mikko Rapeli
b152fcd341 ide/libata: ST310211A has buggy HPA too
Signed-off-by: Mikko Rapeli <mikko.rapeli@teleca.com>
Tested-by: Bart Champagne <bart@as35701.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-02-19 01:41:25 +01:00
Harvey Harrison
5410f729e3 ata: fix sparse warning in pata_acpi.c
drivers/ata/pata_acpi.c:80:2: warning: returning void-valued expression

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:33 -05:00
Harvey Harrison
42268e26aa ata: fix sparse warning in pata_marvell.c
drivers/ata/pata_marvell.c:88:2: warning: returning void-valued expression

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:30 -05:00
Harvey Harrison
ef2f2e4911 ata: fix sparse warning in pata_jmicron.c
drivers/ata/pata_jmicron.c:118:2: warning: returning void-valued expression

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:29 -05:00
Harvey Harrison
2072fb55cf ata: fix sparse warning in pata_cs5536.c
Everybody passes in a u32...why fight it.

drivers/ata/pata_cs5536.c:124:26: warning: incorrect type in argument 3 (different signedness)
drivers/ata/pata_cs5536.c:124:26:    expected int *val
drivers/ata/pata_cs5536.c:124:26:    got unsigned int *<noident>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:27 -05:00
Harvey Harrison
d98f88c222 ata: sparse fixes for pata_amd.c
drop return statement.
drivers/ata/pata_amd.c:149:2: warning: returning void-valued expression

Commit ce54d16163 pata_amd: update mode selection for NV PATAs

added the initializer for nv_mode_filter but missed deleting the previously
set mode_filter

drivers/ata/pata_amd.c:509:3: warning: Initializer entry defined twice
drivers/ata/pata_amd.c:521:3:   also defined here
drivers/ata/pata_amd.c:544:3: warning: Initializer entry defined twice
drivers/ata/pata_amd.c:556:3:   also defined here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:24 -05:00
Akira Iguchi
1ec414ecc0 pata_scc.c: add thaw ops
This patch adds default thaw ops and fixes the freeze/thaw inconsistency.

Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:22 -05:00
Martin K. Petersen
b6966a61a8 pata_cs5536.c bugfix
Fix speed negotiation for secondary device.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:18 -05:00
Tejun Heo
7a3a16fe7d pata_legacy: don't call ata_host_detach() after initialization failure
ata_host_detach() detaches an attached port and shouldn't be called on
a port which hasn't been attached yet.  pata_legacy incorrectly calls
ata_host_detach() on unattached port after initialization failure
causing oops.  Fix it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:12 -05:00
Harvey Harrison
5ab063e397 ata: fix sparse warnings in sata_mv.c
pp is never used again in this function, no need to declare a
new one.

drivers/ata/sata_mv.c:1545:24: warning: symbol 'pp' shadows an earlier one
drivers/ata/sata_mv.c:1501:22: originally declared here
drivers/ata/sata_mv.c:1553:24: warning: symbol 'pp' shadows an earlier one
drivers/ata/sata_mv.c:1501:22: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:03 -05:00
Harvey Harrison
48e1f800ea ata: fix sparse warning in sata_via.c
drivers/ata/sata_via.c:336:2: warning: returning void-valued expression

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:01 -05:00
Harvey Harrison
6903c0f7ef ata: fix sparse warning in sata_promise.c
drivers/ata/sata_promise.c:546:15: warning: symbol 'len' shadows an earlier one
drivers/ata/sata_promise.c:538:6: originally declared here

len is set again immediately after the loop, so this is safe.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:50:59 -05:00
Harvey Harrison
018d982721 ata: fix sparse warning in ata_piix.c
drivers/ata/ata_piix.c:1655:8: warning: symbol 'rc' shadows an earlier one
drivers/ata/ata_piix.c:1616:6: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:50:58 -05:00
Harvey Harrison
eeb37ac874 ata: fix sparse warning in libata-core.c
rc is used to test the return value and possibly return an error.
No need to redeclare inside the loop.

drivers/ata/libata-core.c:7089:7: warning: symbol 'rc' shadows an earlier one
drivers/ata/libata-core.c:7030:9: originally declared here

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:50:56 -05:00
Harvey Harrison
08f01058fe ata: make ata_scsiop_inq_89 static in libata-scsi.c
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:50:53 -05:00
Byron Bradley
fbf14e2f2d sata_mv: platform driver allocs dma without create
When the sata_mv driver is used as a platform driver,
mv_create_dma_pools() is never called so it fails when trying
to alloc in mv_pool_start().

Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11 14:30:10 -05:00
Alan Cox
4194645079 pata_ninja32: setup changes
Forcibly set more of the configuration at init time. This seems to fix at
least one problem reported. We don't know what most of these bits do, but
we do know what windows stuffs there.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11 14:30:07 -05:00
Alan Cox
8397248d46 pata_legacy: typo fix
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11 14:30:06 -05:00
Alan Cox
c9544bcb4c pata_amd: Note in the module description it handles Nvidia
This has confused a few people so fix it

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-11 14:30:04 -05:00