Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've also for a long time had a problem with the
temperature calculation code, which I had fixed
by byte-swapping the values, and now it turns out
that was the correct fix after all.
Also, any use of iwl_eeprom_query_addr() that is
for more than a u8 must be cast to little endian,
and some structs as well.
Fix all this. Again, no real impact on platforms
that already are little endian.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The construct "le16_to_cpu((__force __le16)(r >> 16))" has
always bothered me when looking through the iwlwifi code,
it shouldn't be necessary to __force anything, and before
this code, "r" was obtained with an ioread32, which swaps
each of the two u16 values in it properly when swapping the
entire u32 value. I've had arguments about this code with
people before, but always conceded they were right because
removing it only made things not work at all on big endian
platforms.
However, analysing a failure of the OTP reading code, I now
finally figured out what is going on, and why my intuition
about that code being wrong was right all along.
It turns out that the 'priv->eeprom' u8 array really wants
to have the data in it in little endian. So the force code
above and all really converts *to* little endian, not from
it. Cf., for instance, the function iwl_eeprom_query16() --
it reads two u8 values and combines them into a u16, in a
little-endian way. And considering it more, it makes sense
to have the eeprom array as on the device, after all not
all values really are 16-bit values, the MAC address for
instance is not.
Now, what this really means is that all the annotations are
completely wrong. The eeprom reading code should fill the
priv->eeprom array as a __le16 array, with __le16 values.
This also means that iwl_read_otp_word() should really have
a __le16 pointer as the data argument, since it should be
filling that in a format suitable for priv->eeprom.
Propagating these changes throughout, iwl_find_otp_image()
is found to be, now obviously visible, defective -- it uses
the data returned by iwl_read_otp_word() directly as if it
was CPU endianness. Fixing that, which is this hunk of the
patch:
- next_link_addr = link_value * sizeof(u16);
+ next_link_addr = le16_to_cpu(link_value) * sizeof(u16);
is the only real change of this patch. Everything else is
just fixing the sparse annotations.
Also, the bug only shows up on big endian platforms with a
1000 series card. 5000 and previous series do not use OTP,
and 6000 series has shadow RAM support which means we don't
ever use the defective code on any cards but 1000.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've had many reports of rt61pci failures with powersaving enabled.
Therefore, as a stop-gap measure, disable powersaving of the rt61pci
until we have found a proper solution.
Also disable powersaving on rt2800pci as it most probably will show
the same problem.
Cc: stable@kernel.org
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sizeof(iv16) and sizeof(iv32) are the sizes of pointers. Change them to
the size of the copied data.
Furthermore, iveiv_entry is a local structure that has just been
initialized and is not visible outside this function. Thus, there would
seem to be no point to copy data into it. The order of the arguments is
thus changed to copy the data into the parameters, which are provided as
pointers, suggesting in this case that they should be used to return values.
A simplified version of the semantic patch that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, we copy/paste the padding stuff from ath9k_tx to ath_tx_cabq since it
needs to same kind of padding, but for internally generated beacons.
Next, software padding done on TX needs to be removed before calling
ieee80211_tx_status. The code was already there in ath_tx_complete but it
was wrong. Fix it by using ath9k_cmn_padpos. This later code has been
tested by sending packets to a monitor interface and reading packets from the
same interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commits "iwlwifi: remove power-wasting calls to apm_ops.init()" and
"iwlagn: power up device before initializing EEPROM" had the goal of
reducing device power consumption from the time the module is loaded until
the interface is brought up and the device's power saving mechanisms kick
in. The idea is that once the module is loaded there is no need for the
device to consume power until the interface is brought up.
With the current solution the device is only powered up during EEPROM read,
and then so also only if the EEPROM type is OTP. We have found that on
certain platforms even non-OTP devices require power to be up during EEPROM
read. On these platforms the driver never loads and the system log contains
the following:
iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080403D8
We thus now power up all devices during EEPROM read.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stacking code incorrectly scaled up the data offset in some cases
causing misaligned devices to report alignment. Rewrite the stacking
algorithm to remedy this and apply the same alignment principles to the
discard handling.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The assumption that acpi_table_parse passes the return value
of the hanlder function to the caller proved wrong
recently. The return value of the handler function is
totally ignored. This makes the initialization code for AMD
IOMMU buggy in a way that could cause a kernel panic on
initialization. This patch fixes the issue in the AMD IOMMU
driver.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
If CONFIG_HAVE_DMA_API_DEBUG is defined and "dma_debug=off" is
specified on the kernel command line, when you detach a driver from a
device you can cause the following NULL pointer dereference:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c0580d35>] dma_debug_device_change+0x5d/0x117
The problem is that the dma_debug_device_change notifier function is
added to the bus notifier chain even though the dma_entry_hash array
was never initialized. If dma debugging is disabled, this patch both
prevents dma_debug_device_change notifiers from being added to the
chain, and additionally ensures that the dma_debug_device_change
notifier function is a no-op.
Cc: stable@kernel.org
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
rsp->count is unsigned so the test does not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Memory amount is increased before a successful write-read
sequence is done. Thus, 512 kB of onboard memory is detected
on memoryless cards like SB32.
Move the increasing of memory counter after successful read
is done.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The direction of rounding is incorrect in the snd_interval_ratnum()
It was detected with following parameters (sb8 driver playing
8kHz stereo file):
- num is always 1000000
- requested frequency rate is from 7999 to 7999 (single frequency)
The first loop calculates div_down(num, freq->min) which is 125.
Thus, a frequency range's minimum value is 1000000 / 125 = 8000 Hz.
The second loop calculates div_up(num, freq->max) which is 126
The frequency range's maximum value is 1000000 / 126 = 7936 Hz.
The range maximum is lower than the range minimum so the function
fails due to empty result range.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current Realtek code makes no specific provision for turning stuff
off. The codec chip is placed into low-power mode generically, but this
doesn't turn off any external hardware connected to it, in particular
external amplifiers.
This patch creates a hook function that is called by the codec
suspend/resume functions. It ought to disable any external hardware in a
device-specific way. I've implemented a generic ALC889 function that
sets the EAPD pin properly, and used it for the Acer Aspire 8930G which
can benefit from this feature.
On my laptop, this results in ~0.5W extra savings.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes some extra mixers that do nothing on the Acer Aspire
8930G.
The CD mixer is useless because the SATA DVD/Blu-Ray drive has no analog
audio output, and the Side mixer is useless because we max out at 6ch
anyway.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch just simplifies the 8930G verb array a bit. Just use the
common ALC889 EAPD verb array to make things more consistent. The file
is already huge enough already.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugs.launchpad.net/bugs/479373
The OR has verified with hda-verb that the internal microphone needs
VREF50 set for audible capture.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A typo in 12045a6ee9 "nfsd: let "insecure" flag vary by
pseudoflavor" reversed the sense of the "insecure" flag.
Reported-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't actually require this in the cpu_relax() polling case, so just
cuddle these around the sleeping version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The error was introduced while merging:
commit 4529819c45
bnx2: reset_task is crashing the kernel. Fixing it.
Signed-off-by: Michael Chan <mchan@broadcom.com>k
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1317) fixes a bug in the PM core. When a device is
resumed following a system sleep, the core decrements the device's
runtime PM usage counter but doesn't issue an idle notification if the
counter reaches 0. This could prevent an otherwise unused device from
being runtime-suspended again after the system sleep.
The fix is to call pm_runtime_put_sync() instead of
pm_runtime_put_noidle().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix the following build failures:
arch/powerpc/platforms/embedded6xx/flipper-pic.c: In function 'flipper_pic_map':
arch/powerpc/platforms/embedded6xx/flipper-pic.c:105: error: implicit declaration of function 'get_irq_desc'
arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_map':
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:98: error: implicit declaration of function 'get_irq_desc'
These failures are caused by the changes introduced in commit
"powerpc: Remove get_irq_desc()". The reason these drivers were not
updated is that they weren't merged yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the following build failures:
arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_irq_cascade':
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:135: error: passing argument 1 of 'spin_lock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:137: error: passing argument 1 of 'spin_unlock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:145: error: passing argument 1 of 'spin_lock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:149: error: passing argument 1 of 'spin_unlock' from incompatible pointer type
These failures are caused by the changes introduced in commit
"genirq: Convert irq_desc.lock to raw_spinlock". The reason this driver
was not updated is that it wasn't merged yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hot-unplug kstopmachine usage does a wakeup after
deactivating the cpu, hence we cannot use cpu_active()
here but must rely on the good olde online.
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <1261326987.4314.24.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
adev->dma_mode stores the transfer mode value not UDMA mode number
so the condition in cmd64x_set_dmamode() is always true and the higher
UDMA clock is always selected. This can potentially result in data
corruption when UDMA33 device is used, when 40-wire cable is used or
when the error recovery code decides to lower the device speed down.
The issue was introduced in the commit 6a40da0 ("libata cmd64x: whack
into a shape that looks like the documentation") which goes back to
kernel 2.6.20.
Cc: stable@kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This reverts commit d43744390e, because
it breaks the boot on several machines (mostly sparc64, at present).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Revert the braindead pr_* crap. (Commit 663997d "sched: Use
pr_fmt() and pr_<level>()")
It's dumb and causes stupid "sched: " strings all over the place.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mike Galbraith <efault@gmx.de>
Cc: Joe Perches <joe@perches.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1261315437.4314.6.camel@laptop>
[ i dont mind the pr_*() patterns that much - but Peter dislikes them with a vengence. ]
[ - v2: remove spurious diffstat from changelog :-/ ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Correct grammos. Spell out words. Add missing words.
Consistent use of "mcount()" function name.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <4B2C0D78.6060707@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix typos, spellos, hyphenation, line lengths.
BTW: are there some userspace tools? There is a reference to
some at the wiki page, but there are no tools listed there.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Pekka Paalanen <pq@iki.fi>
LKML-Reference: <4B2C0D68.6080401@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Put the ioat2 and ioat3 state machines in the halted state with all
errors cleared.
The ioat1 init path is not disturbed for stability, there are no
reported ioat1 initiaization issues.
Cc: <stable@kernel.org>
Reported-by: Roland Dreier <rdreier@cisco.com>
Tested-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Convert BUG() to use unreachable()
alpha: Add minimal support for software performance events
alpha: Wire up missing/new syscalls
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: remove pointless NULL test
pata_hpt3x2n: fix clock turnaround
libata: fix reporting of drained bytes when clearing DRQ
sata_mv: add power management support for the PCI controllers.
sata_mv: store the board_idx into the host private data
pata_octeon_cf: use resource_size(), to fix resource sizing bug
libata: use the WRITE_SAME_16 define
sata_mv: move the PCI bar description initialization code
sata_mv: add power management support for the platform driver
sata_mv: support clkdev framework
sata_mv: increase PIO IORDY timeout
Fixed crazy mode-change in merge.