Now that we have same helper used for all icache invalidates (i.e.
vaddr+paddr based exact line invalidate), consolidate the open coded
calls into one place.
Also rename flush_icache_range_vaddr => __sync_icache_dcache
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This change continues the theme from prev commit - this time icache
handling for kernel's own code modification (vmalloc: loadable modules,
breakpoints for kprobes/kgdb...)
flush_icache_range() calls the CDU icache helper with vaddr to enable
exact line invalidate.
For a true kernel-virtual mapping, the vaddr is actually virtual hence
valid as index into cache. For kprobes breakpoint however, the vaddr arg
is actually paddr - since that's how normal kernel is mapped in ARC
memory map. This implies that CDU will use the same addr for
indexing as for tag match - which is fine since kernel code would only
have that "implicit" mapping and none other.
This should speed up module loading significantly - specially on default
ARC700 icache configurations (32k) which alias.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC icache doesn't snoop dcache thus executable pages need to be made
coherent before mapping into userspace in flush_icache_page().
However ARC700 CDU (hardware cache flush module) requires both vaddr
(index in cache) as well as paddr (tag match) to correctly identify a
line in the VIPT cache. A typical ARC700 SoC has aliasing icache, thus
the paddr only based flush_icache_page() API couldn't be implemented
efficiently. It had to loop thru all possible alias indexes and perform
the invalidate operation (ofcourse the cache op would only succeed at
the index(es) where tag matches - typically only 1, but the cost of
visiting all the cache-bins needs to paid nevertheless).
Turns out however that the vaddr (along with paddr) is available in
update_mmu_cache() hence better suits ARC icache flush semantics.
With both vaddr+paddr, exactly one flush operation per line is done.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
munmap ends up calling tlb_flush() which for ARC was flushing the entire
TLB unconditionally (by moving the MMU to a new ASID)
do_munmap
unmap_region
unmap_vmas
unmap_single_vma
unmap_page_range
tlb_start_vma
zap_pud_range
tlb_end_vma()
tlb_finish_mmu
tlb_flush() ---> unconditional flush_tlb_mm()
So even a single page munmap, a frequent operation when uClibc dynamic
linker (ldso) is loading the dependent shared libraries, would move the
the ASID multiple times - needlessly invalidating the pre-faulted TLB
entries (and increasing the rate of ASID wraparound + full TLB flush).
This is now optimised to only be called if tlb->full_mm (which means
for exit/execve) cases only. And for those cases, flush_tlb_mm() is
already optimised to be a no-op for mm->mm_users == 0.
So essentially there are no mmore full mm flushes - except for fork which
anyhow needs it for properly COW'ing parent address space.
munmap now needs to do TLB range flush, which is implemented with
tlb_end_vma()
Results
-------
1. ASID now consistenly moves by 4 during a simple ls (as opposed to 5 or
7 before).
2. LMBench microbenchmark also shows improvements
Basic system parameters
------------------------------------------------------------------------------
Host OS Description Mhz tlb cache mem scal
pages line par load
bytes
--------- ------------- ----------------------- ---- ----- ----- ------ ----
3.9-rc5-0 Linux 3.9.0-r 3.9-rc5-0404-gcc-4.4-ba 80 8 64 1.1000 1
3.9-rc5-0 Linux 3.9.0-r 3.9-rc5-0405-avoid-full 80 8 64 1.1200 1
Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
3.9-rc5-0 Linux 3.9.0-r 80 4.81 8.69 68.6 118. 239. 8.53 31.6 4839 13.K 34.K
3.9-rc5-0 Linux 3.9.0-r 80 4.46 8.36 53.8 91.3 223. 8.12 24.2 4725 13.K 33.K
File & VM system latencies in microseconds - smaller is better
-------------------------------------------------------------------------------
Host OS 0K File 10K File Mmap Prot Page 100fd
Create Delete Create Delete Latency Fault Fault selct
--------- ------------- ------ ------ ------ ------ ------- ----- ------- -----
3.9-rc5-0 Linux 3.9.0-r 314.7 223.2 1054.9 390.2 3615.0 1.590 20.1 126.6
3.9-rc5-0 Linux 3.9.0-r 265.8 183.8 1014.2 314.1 3193.0 6.910 18.8 110.4
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This adds support for an ARC Virtual Platform. This platform is based on the
System C standard promoted by the OSCI (Open System C Initiative) and uses
nSIM to simulate the ARC CPU core itself.
Users can build a virtual SoC by combining System C models of peripherals
and CPU cores.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original device tree was written using a slightly different
implementation of the fixed-factor-clock device tree binding. The
compatible string must be modified in order to be compatible with the
new implementation.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Infrastructure required to make the Linux kernel compile and boot on the
Abilis Systems TB10x series of SOCs based on ARC700 CPUs:
- Kmake related files (Kconfig, Makefile, tb10x_defconfig)
- TB10x platform initialisation
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
These are the device tree files for the Abilis Systems TB100 and TB101 ICs and
their respective development kit PCBs. These files are committed in preparation
of the following patch set which adds support for these chips to the ARC
platform.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch adds some room for CPU-external interrupt controllers in the
Linux interrupt space. Until now, only the 32 CPU internal interrupt lines
were supported which does not allow for external interrupt controllers such
as GPIO modules etc.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arc-intc is initialized in arc common code as it is applicable to all
platforms. However platforms with their own external intc still need to
refer to it for correct DT interrupt tree hierarchy setup,
e.g.
static struct of_device_id __initdata tb10x_irq_ids[] = {
{ .compatible = "snps,arc700-intc", .data = dummy_init_irq },
{ .compatible = "abilis,tb10x_ictl", .data = tb10x_init_irq },
{},
};
The fix is to use the generic irqchip framework to tie all irqchips in
a special linker section and then call irqchip_init() which calls the
DT of_irq_init() for all the intc in one go.
That way the platform code need not be aware of arc-intc at all.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The existing code was wrong on several counts:
* uboot provided bootargs were copied into @boot_command_line, only to
be over-written by setup_machine_fdt(), effectively lost
* @cmdline_p returned by setup_arch() to start_kernel() didn't include
the DT /bootargs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Given that DeviceTree /bootargs can provide similar functionality,
no point in providing duplicate infrastructure.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The fixup code correctly updates the callee-regs on stack, but
fails to unwind it into actual register file. Thus userspace won't see
the update.
Reported-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
If CONFIG_ARC_MISALIGN_ACCESS is not enabled, or if the fixup fails,
call the same error handler: same signal/si_code to user (SIGBUS)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Remove the line-break between scratch/callee-regs (sneaked in when we
converted from printk to pr_*
* Use %pS to print the symbol names of faulting PC (ret pseudo register)
and BLINK (call return register)
* Don't print user-vma for a kernel crash (only do it for
print-fatal-signals based regfile dump)
* Verbose print the Interrupt/Exception Enable/Active state
* for main executable link address is 0x10000 based (vs. 0) thus offset
of faulting PC needs to be adjusted
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This tracks mainline commit ae903caae2 "Bury the conditionals from
kernel_thread/kernel_execve series" which we missed out as ARC port was
not yet mainline.
[vgupta: commit log modified]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
show_regs() is inherently arch-dependent but it does make sense to print
generic debug information and some archs already do albeit in slightly
different forms. This patch introduces a generic function to print debug
information from show_regs() so that different archs print out the same
information and it's much easier to modify what's printed.
show_regs_print_info() prints out the same debug info as dump_stack()
does plus task and thread_info pointers.
* Archs which didn't print debug info now do.
alpha, arc, blackfin, c6x, cris, frv, h8300, hexagon, ia64, m32r,
metag, microblaze, mn10300, openrisc, parisc, score, sh64, sparc,
um, xtensa
* Already prints debug info. Replaced with show_regs_print_info().
The printed information is superset of what used to be there.
arm, arm64, avr32, mips, powerpc, sh32, tile, unicore32, x86
* s390 is special in that it used to print arch-specific information
along with generic debug info. Heiko and Martin think that the
arch-specific extra isn't worth keeping s390 specfic implementation.
Converted to use the generic version.
Note that now all archs print the debug info before actual register
dumps.
An example BUG() dump follows.
kernel BUG at /work/os/work/kernel/workqueue.c:4841!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #7
Hardware name: empty empty/S3992, BIOS 080011 10/26/2007
task: ffff88007c85e040 ti: ffff88007c860000 task.ti: ffff88007c860000
RIP: 0010:[<ffffffff8234a07e>] [<ffffffff8234a07e>] init_workqueues+0x4/0x6
RSP: 0000:ffff88007c861ec8 EFLAGS: 00010246
RAX: ffff88007c861fd8 RBX: ffffffff824466a8 RCX: 0000000000000001
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffffffff8234a07a
RBP: ffff88007c861ec8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff8234a07a
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88015f7ff000 CR3: 00000000021f1000 CR4: 00000000000007f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88007c861ef8 ffffffff81000312 ffffffff824466a8 ffff88007c85e650
0000000000000003 0000000000000000 ffff88007c861f38 ffffffff82335e5d
ffff88007c862080 ffffffff8223d8c0 ffff88007c862080 ffffffff81c47760
Call Trace:
[<ffffffff81000312>] do_one_initcall+0x122/0x170
[<ffffffff82335e5d>] kernel_init_freeable+0x9b/0x1c8
[<ffffffff81c47760>] ? rest_init+0x140/0x140
[<ffffffff81c4776e>] kernel_init+0xe/0xf0
[<ffffffff81c6be9c>] ret_from_fork+0x7c/0xb0
[<ffffffff81c47760>] ? rest_init+0x140/0x140
...
v2: Typo fix in x86-32.
v3: CPU number dropped from show_regs_print_info() as
dump_stack_print_info() has been updated to print it. s390
specific implementation dropped as requested by s390 maintainers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile bits]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both dump_stack() and show_stack() are currently implemented by each
architecture. show_stack(NULL, NULL) dumps the backtrace for the
current task as does dump_stack(). On some archs, dump_stack() prints
extra information - pid, utsname and so on - in addition to the
backtrace while the two are identical on other archs.
The usages in arch-independent code of the two functions indicate
show_stack(NULL, NULL) should print out bare backtrace while
dump_stack() is used for debugging purposes when something went wrong,
so it does make sense to print additional information on the task which
triggered dump_stack().
There's no reason to require archs to implement two separate but mostly
identical functions. It leads to unnecessary subtle information.
This patch expands the dummy fallback dump_stack() implementation in
lib/dump_stack.c such that it prints out debug information (taken from
x86) and invokes show_stack(NULL, NULL) and drops arch-specific
dump_stack() implementations in all archs except blackfin. Blackfin's
dump_stack() does something wonky that I don't understand.
Debug information can be printed separately by calling
dump_stack_print_info() so that arch-specific dump_stack()
implementation can still emit the same debug information. This is used
in blackfin.
This patch brings the following behavior changes.
* On some archs, an extra level in backtrace for show_stack() could be
printed. This is because the top frame was determined in
dump_stack() on those archs while generic dump_stack() can't do that
reliably. It can be compensated by inlining dump_stack() but not
sure whether that'd be necessary.
* Most archs didn't use to print debug info on dump_stack(). They do
now.
An example WARN dump follows.
WARNING: at kernel/workqueue.c:4841 init_workqueues+0x35/0x505()
Hardware name: empty
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #9
0000000000000009 ffff88007c861e08 ffffffff81c614dc ffff88007c861e48
ffffffff8108f50f ffffffff82228240 0000000000000040 ffffffff8234a03c
0000000000000000 0000000000000000 0000000000000000 ffff88007c861e58
Call Trace:
[<ffffffff81c614dc>] dump_stack+0x19/0x1b
[<ffffffff8108f50f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8108f56a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8234a071>] init_workqueues+0x35/0x505
...
v2: CPU number added to the generic debug info as requested by s390
folks and dropped the s390 specific dump_stack(). This loses %ksp
from the debug message which the maintainers think isn't important
enough to keep the s390-specific dump_stack() implementation.
dump_stack_print_info() is moved to kernel/printk.c from
lib/dump_stack.c. Because linkage is per objecct file,
dump_stack_print_info() living in the same lib file as generic
dump_stack() means that archs which implement custom dump_stack()
- at this point, only blackfin - can't use dump_stack_print_info()
as that will bring in the generic version of dump_stack() too. v1
The v1 patch broke build on blackfin due to this issue. The build
breakage was reported by Fengguang Wu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390 bits]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull SMP/hotplug changes from Ingo Molnar:
"This is a pretty large, multi-arch series unifying and generalizing
the various disjunct pieces of idle routines that architectures have
historically copied from each other and have grown in random, wildly
inconsistent and sometimes buggy directions:
101 files changed, 455 insertions(+), 1328 deletions(-)
this went through a number of review and test iterations before it was
committed, it was tested on various architectures, was exposed to
linux-next for quite some time - nevertheless it might cause problems
on architectures that don't read the mailing lists and don't regularly
test linux-next.
This cat herding excercise was motivated by the -rt kernel, and was
brought to you by Thomas "the Whip" Gleixner."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
idle: Remove GENERIC_IDLE_LOOP config switch
um: Use generic idle loop
ia64: Make sure interrupts enabled when we "safe_halt()"
sparc: Use generic idle loop
idle: Remove unused ARCH_HAS_DEFAULT_IDLE
bfin: Fix typo in arch_cpu_idle()
xtensa: Use generic idle loop
x86: Use generic idle loop
unicore: Use generic idle loop
tile: Use generic idle loop
tile: Enter idle with preemption disabled
sh: Use generic idle loop
score: Use generic idle loop
s390: Use generic idle loop
powerpc: Use generic idle loop
parisc: Use generic idle loop
openrisc: Use generic idle loop
mn10300: Use generic idle loop
mips: Use generic idle loop
microblaze: Use generic idle loop
...
Use common help functions to free reserved pages.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, for every ARC kernel build I see the following:
--------------->8-----------------
DTB arch/arc/boot/dts/angel4.dtb.S
AS arch/arc/boot/dts/angel4.dtb.o
LD arch/arc/boot/dts/built-in.o
rm arch/arc/boot/dts/angel4.dtb.S <-- forces rebuild next iter
CHK kernel/config_data.h
--------------->8-----------------
This is because *.dts.S is intermediate file in dtb generation and is by
default deleted by make which needs a ".SECONDARY" hint to NOT do so.
This could have ideally been done in scripts/Makefile.lib - for benefit
of all, however .SECONDARY doesn't seem to work with wildcards.
Thanks to Stephen for suggesting .SECONDARY (vs .PRECIOUS) and making
that work using a non wildcard version in arch makefile.
Thanks to James Hogan for pointing out that *.dtb.S now needs to be
added to clean-files
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
commit "fs: make binfmt support for #! scripts modular and removable"
made support for #!scripts optional - thus need to include the Kconfig
file to get all relevant BINFMT_*
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Currently ARC_HAS_LLSC can be influenced by platform for SMP only using
ARC_HAS_COH_LLSC. For !SMP it defaults to "y".
It turns out that some customers can't support it all, even in UP.
So we change the semantics, and use a negative dependency ARC_CANT_LLSC.
Any platform (independent of SMP or !SMP) can select it to disable LLSC.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arch/arc/kernel/traps.c no longer compiles without explicitly including
asm/kprobes.h
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The existing uImage target always generates gzip compressed image which
drags bootup for some very slow FPGA customer boards.
So introduce seperate make targets:uImage.{bin,gz} with uncompressed
being default. Also tie gz generation to CONFIG_KERNEL_GZIP, which a
platform can select in it's Kconfig if it wishes gz to be default.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We do cross compiles for ARC Linux.
With gcc 4.7, a make defconfig spews out the following:
------------------->8--------------------------
make ARCH=arc defconfig
gcc: error: unrecognized command line option '-marc600'
gcc: error: unrecognized command line option '-mA7'
gcc: error: unrecognized command line option '-mno-sdata'
gcc: error: unrecognized command line option '-mno-mpy'
*** Default configuration is based on 'fpga_defconfig'
------------------->8--------------------------
This apparently is coming from LIBGCC line - which is strange to be
invoked for defconfig generation.
Reported-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There's no (Kconfig) macro CONFIG_BLOCK_DEV_RAM. (CONFIG_BLK_DEV_RAM
does exist though.) But linux/blk.h got killed in 2005 anyway (in a
patch titled "kill blk.h"), so these three lines can be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Some header files were included twice in the same file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Fixes the following coding style issues as detected by checkpatch:
ERROR: space required before the open parenthesis '('
ERROR: "foo * bar" should be "foo *bar"
WARNING: space prohibited between function name and open parenthesis '('
WARNING: please, no spaces at the start of a line
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Silences the following checkpatch warnings:
WARNING: Use #include <linux/ptrace.h> instead of <asm/ptrace.h>
WARNING: Use #include <linux/kprobes.h> instead of <asm/kprobes.h>
WARNING: Use #include <linux/kgdb.h> instead of <asm/kgdb.h>
WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
WARNING: Use #include <linux/cache.h> instead of <asm/cache.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
version.h header file inclusion is not necessary as detected by
versioncheck script.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC irqsave/restore macros were missing the compiler barrier, causing a
stale load in irq-enabled region be used in irq-safe region, despite
being changed, because the register holding the value was still live.
The problem manifested as random crashes in timer code when stress
testing ARCLinux (3.9-rc3) on a !SMP && !PREEMPT_COUNT
Here's the exact sequence which caused this:
(0). tv1[x] <----> t1 <---> t2
(1). mod_timer(t1) interrupted after it calls timer_pending()
(2). mod_timer(t2) completes
(3). mod_timer(t1) resumes but messes up the list
(4). __runt_timers( ) uses bogus timer_list entry / crashes in
timer->function
Essentially mod_timer() was racing against itself and while the spinlock
serialized the tv1[] timer link list, timer_pending() called outside the
spinlock, cached timer link list element in a register.
With low register pressure (and a deep register file), lack of barrier
in raw_local_irqsave() as well as preempt_disable (!PREEMPT_COUNT
version), there was nothing to force gcc to reload across the spinlock,
causing a stale value in reg be used for link list manipulation - ensuing
a corruption.
ARcompact disassembly which shows the culprit generated code:
mod_timer:
push_s blink
mov_s r13,r0 # timer, timer
..
###### timer_pending( )
ld_s r3,[r13] # <------ <variable>.entry.next LOADED
brne r3, 0, @.L163
.L163:
..
###### spin_lock_irq( )
lr r5, [status32] # flags
bic r4, r5, 6 # temp, flags,
and.f 0, r5, 6 # flags,
flag.nz r4
###### detach_if_pending( ) begins
tst_s r3,r3 <--------------
# timer_pending( ) checks timer->entry.next
# r3 is NOT reloaded by gcc, using stale value
beq.d @.L169
mov.eq r0,0
##### detach_timer( ): __list_del( )
ld r4,[r13,4] # <variable>.entry.prev, D.31439
st r4,[r3,4] # <variable>.prev, D.31439
st r3,[r4] # <variable>.next, D.30246
We initially tried to fix this by adding barrier() to preempt_* macros
for !PREEMPT_COUNT but Linus clarified that it was anything but wrong.
http://www.spinics.net/lists/kernel/msg1512709.html
[vgupta: updated commitlog]
Reported-by/Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Debugged-by/Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic idle loop implements all functionality. Aside of that it
allows arc to implement the tsk_is_polling() functionality correctly,
despite the patently (now gone) comment in the original arc cpu_idle()
function:
/* Since we SLEEP in idle loop, TIF_POLLING_NRFLAG can't be set */
See kernel/cpu/idle.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Tested-by: Vineet Gupta <vgupta@synopsys.com>
Link: http://lkml.kernel.org/r/20130321215233.711253792@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
orig_r8_IS_EXCPN and orig_r8_IS_BRKPT were same values due to a
copy/paste error. Although it looks bad and is wrong, it really doesn't
affect gdb working.
orig_r8_IS_BRKPT is the one relevant to debugging (breakpoints), since
it is used to provide EFA vs. ERET to a ptrace "stop_pc" request.
So when gdb has inserted a breakpoint, orig_r8_IS_BRKPT is already set,
and anything else (i.e. orig_r8_IS_EXCPN) becoming same as it, really
doesn't hurt gdb. The corollary case, could be nasty but nobody uses the
ptrace "stop_pc" request in that case
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
CC drivers/mmc/host/mmc_spi.o
drivers/mmc/host/mmc_spi.c:118: error: redefinition of 'struct scratch'
make[3]: *** [drivers/mmc/host/mmc_spi.o] Error 1
make[2]: *** [drivers/mmc/host] Error 2
make[1]: *** [drivers/mmc] Error 2
make: *** [drivers] Error 2
CC arch/arc/kernel/kgdb.o
In file included from include/linux/kgdb.h:20,
from arch/arc/kernel/kgdb.c:11:
/home/vineetg/arc/k.org/arc-port/arch/arc/include/asm/kgdb.h:34:
warning: 'struct pt_regs' declared inside parameter list
/home/vineetg/arc/k.org/arc-port/arch/arc/include/asm/kgdb.h:34:
warning: its scope is only this definition or declaration, which is
probably not what you want
arch/arc/kernel/kgdb.c:172: error: conflicting types for 'kgdb_trap'
CC arch/arc/kernel/kgdb.o
arch/arc/kernel/kgdb.c: In function 'pt_regs_to_gdb_regs':
arch/arc/kernel/kgdb.c:62: error: dereferencing pointer to incomplete
type
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The upstream kernel ABI (v3) is different from current out-of-tree (v2):
* no-legacy-syscalls
* user_regs_struct layout has changed
So we rev up the ABI version
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ptrace regset interface relies on ELF_NGREG for ceiling the size of user
request. So any larger request (even if legit) would be clipped.
The existing def of ELF_NGREG didn't use user_regs_struct and was
technically one placeholder short (stop_pc) - although the current code
would still work because pt_regs includes a bunch of extra fields,
making
ELF_NGREG >= sizeof(struct user_regs_struct)/sizeof(long)
But we need to remove this ambiguity, specially since pt_regs should NOT
be directly associated with with anything userspace-ish.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The flat DT (currently embedded in vmlinux) is in .init section.
The unflattened/binary tree doesn't copy strings through and references
them from orig flat DT - which could cause catestrohpy if of_* APIs are
called post init, say from a driver which is a loadable module.
Reported-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Syscall restarting fixes made pt_regs->orig_r8 a short word, which was
not reflected in the assembler code - thus could potentially break gdb
debugging.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Commit 0bbacca "hlist: drop the node parameter from iterators" changed
the iterator across the board - but ARC port being out-of-tree missed
it.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The 64bit RTSC is not reliable, causing spurious "jumps" in higher word,
making Linux timekeeping go bonkers. So as of now just use the lower
32bit timestamp.
A cleaner approach would have been removing RTSC support altogether as the
32bit RTSC is equivalent to old TIMER1 based solution, but some customers
can use the 32bit RTSC in SMP syn fashion (vs. TIMER1 which being incore
can't be done easily).
A fallout of this is sched_clock()'s hardware assisted version needs to
go away since it can't use 32bit wrapping counter - instead we use the
generic "weak" jiffies based version.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
!CONFIG_ARC_HAS_(I|D)CACHE makes Linux disable caches (assuming they
exist in hardware) - mostly for debugging issues with new peripherals.
However, independent of CONFIG_ARC_HAS_(I|D)CACHE, Linux also needs to
handle, non-existant caches, using the information in Cache BCRs (Build
Configuration Reg)
Reported-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Platforms export their SMP callbacks by populating arc_smp_ops.
The population itself needs to be done pretty early, from init_early
callback.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
This again is for switch from singleton platform SMP API to
multi-platform paradigm
Platform code is not yet setup to populate the callbacks, that happens
in next commit
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
All the current platforms can work with 0x8000_0000 based dma_addr_t
since the Bus Bridges typically ignore the top bit (the only excpetion
was Angel4 PCI-AHB bridge which we no longer care for).
That way we don't need plat-specific cpu-addr to bus-addr conversion.
Hooks still provided - just in case a platform has an obscure device
which say needs 0 based bus address.
That way <asm/dma_mapping.h> no longer needs to unconditinally include
<plat/dma_addr.h>
Also verfied that on Angel4 board, other peripherals (IDE-disk / EMAC)
work fine with 0x8000_0000 based dma addresses.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
For now this will suffice for all platforms, later exotic ones needs to
get this from DeviceTree
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
-platform API is retired and instead callbacks are used
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The orig platform code orgnaization was singleton design pattern - only
one platform (and board thereof) would build at a time.
Thus any platform/board specific code (e.g. irq init, early init ...)
expected by ARC common code was exported as well defined set of APIs,
with only ONE instance building ever.
Now with multiple-platform build requirement, that design of code no
longer holds - multiple board specific calls need to build at the same
time - so ARC common code can't use the API approach, it needs a
callback based design where each board registers it's specific set of
functions, and at runtime, depending on board detection, the callbacks
are used from the registry.
This commit adds all the infrastructure, where board specific callbacks
are specified as a "maThine description".
All the hooks are placed in right spots, no board callbacks registered
yet (with MACHINE_STARt/END constructs) so the hooks will not run.
Next commit will actually convert the platform to this infrastructure.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This is more natural and is now doable since the choice constructs are
gone.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This mini patchseries addresses the lack of multi-platform-image support
in ARC port.
Older build system only supported one platform(soc) to build at a time
and further only one board of that platform could be built. There was no
technical reason for that - we just didn't have the need.
So the first step towards multi-platform (and multi-board) builds it to
allow build system to do that.
So as applicable, <choice .. endchoice> => <menu .. endmenu>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Implement ioremap_prot() to allow mapping IO memory with variable
protection
via TLB.
Implementing this allows the /dev/mem driver to use its generic access()
VMA callback, which in turn allows ptrace to examine data in memory
mapped regions mapped via /dev/mem, such as Arc DCCM.
The end result is that it is possible to examine values of variables
placed into DCCM in user space programs via GDB.
CC: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
CC: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
1. ./genfilelist.pl arch/arc/include/asm/
2. Create arch/arc/include/uapi/asm/Kbuild as follows
+# UAPI Header export list
+include include/uapi/asm-generic/Kbuild.asm
3. ./disintegrate-one.pl arch/arc/include/{,uapi/}asm/<above-list>
4. Edit arch/arc/include/asm/Kbuild to remove ref to
asm-generic/Kbuild.asm
- To work around empty uapi/asm/setup.h added a placholder comment.
- Also a manual #ifdef __ASSEMBLY__ for a late ptrace change
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: David Howells <dhowells@redhat.com>
This allows ARC Target to do I/O to host in absence of any peripherals
whatsoever, assisted by Metaware Hostlink facility.
Further we have a FUSE based filesystem which makes us mount/access host
filesystem on target and do fops.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Includes mapping of CCMs in address space
* Annotations to move arbitrary code/data into CCM
* Moving some of the critical code/data into CCM
* Runtime detection/reporting
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC700 doesn't natively support unaligned access, but can be emulated
-Unaligned Access Exception
-Disassembly at the Fault address to find the exact insn (long/short)
Also per Arnd's comment, we runtime control it using 2 sysctl knobs:
* SYSCTL_ARCH_UNALIGN_ALLOW: Runtime enable/disble
* SYSCTL_ARCH_UNALIGN_NO_WARN: Warn on each emulation attempt
Originally contributed by Tim Yao <tim.yao@amlogic.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Tim Yao <tim.yao@amlogic.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
-Originally written by Rajeshwar Ranga
-Derived off of generic unwinder in 2.6.19 and adapted to ARC
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Rajeshwar Ranga <rajeshwar.ranga@gmail.com>
ARC common code to enable a SMP system + ISS provided SMP extensions.
ARC700 natively lacks SMP support, hence some of the core features are
are only enabled if SoCs have the necessary h/w pixie-dust. This
includes:
-Inter Processor Interrupts (IPI)
-Cache coherency
-load-locked/store-conditional
...
The low level exception handling would be completely broken in SMP
because we don't have hardware assisted stack switching. Thus a fair bit
of this code is repurposing the MMU_SCRATCH reg for event handler
prologues to keep them re-entrant.
Many thanks to Rajeshwar Ranga for his initial "major" contributions to
SMP Port (back in 2008), and to Noam Camus and Gilad Ben-Yossef for help
with resurrecting that in 3.2 kernel (2012).
Note that this platform code is again singleton design pattern - so
multiple SMP platforms won't build at the moment - this deficiency is
addressed in subsequent patches within this series.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rajeshwar Ranga <rajeshwar.ranga@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
There is a bit of hack/kludge right now where we disable preemption if a
L2 (High prio) IRQ is taken while L1 (Low prio) is active.
Need to revisit this
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This was part of port buildup strategy from Arnd to have a minimal kernel
at first and then add optional features (stacktracing, ptrace, smp,
kprobes, oprofile....)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* arc-uart platform device now populated dynamically, using
of_platform_populate() - applies to any other device whatsoever.
* uart in turn requires incore arc-intc to be also present in DT
* A irq-domain needs to be instantiated for IRQ requests by DT probed
device (e.g. arc-uart)
TODO: switch over to linear irq domain once all devs have been
transitioned to DT
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
This is minimal infrastructure needed for devicetree work.
It uses an a sample "skeleton" devicetree - embedded in kernel image -
to print the board, manufacturer by parsing the top-level "compatible"
string.
As of now we don't need any additional "board" specific "machine_desc".
TODO: support interpreting the command line as boot-loader passed dtb
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
N.B. This is old style of hardcoding platform device specific info
in code and it's instantiation thererof using platform_add_devices().
Subsequent patches replace this with DeviceTree based runtime probe.
This patch has been retained just as an example of "don't-do-this" for
newer kernel ports.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
This includes recent changes to make handler "retry" and/or "killable"
The killable (early exit) logic is loosely based on how SH implements it
return if SIGKILL + either of VM_FAULT_OOM or VM_FAULT_RETRY
which is different from Hexagon implementation which would NOT early
exit for
SIGKILL + VM_FAULT_OOM + !VM_FAULT_RETRY
credits: Non executable stack support from Simon Spooner
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC700 MMU provides for tagging TLB entries with a 8-bit ASID to avoid
having to flush the TLB every task switch.
It also allows for a quick way to invalidate all the TLB entries for
task useful for:
* COW sementics during fork()
* task exit()ing
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC700 has VIPT L1 Caches
* Caches don't snoop and are not coherent
* Given the PAGE_SIZE and Cache associativity, we don't support aliasing
D$ configurations (yet), but do allow aliasing I$ configs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Per Al Viro's "signals for dummies" https://lkml.org/lkml/2012/12/6/366
there are 3 golden rules for (not) restarting syscalls:
" What we need to guarantee is
* restarts do not happen on signals caught in interrupts or exceptions
* restarts do not happen on signals caught in sigreturn()
* restart should happen only once, even if we get through do_signal()
many times."
ARC Port already handled #1, this patch fixes#2 and #3.
We use the additional state in pt_regs->orig_r8 to ckh if restarting
has already been done once.
Thanks to Al Viro for spotting this.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
To avoid multiple syscall restarts (multiple signals) or no restart at
all (sigreturn), we need just an extra bit of state "literally 1 bit" in
struct pt_regs. orig_r8 is the best place to do this, however given the
way it is encoded currently, we can't add anything simplistically.
Current orig_r8:
* syscalls -> 1 to NR_SYSCALLS
* Exceptions -> NR_SYSCALLS + 1
* Break-point-> NR_SYSCALLS + 2
In new scheme it is a bit-field
* lower short word contains the exact event type (and a new bit to represent
restart semantics : if syscall was already / can't be restarted)
* upper short word optionally containing the syscall num - needed by
likes of tracehooks etc
This patch only changes how orig_r8 is organised and nothing should
change behaviourily.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Includes following fixes courtesy review by Al-Viro
* Tracer poke to Callee-regs were lost
Before going off into do_signal( ) we save the user-mode callee regs
(as they are not saved by default as part of pt_regs). This is to make
sure that that a Tracer (if tracing related signal) is able to do likes
of PEEKUSR(callee-reg).
However in return path we were simply discarding the user-mode callee
regs, which would break a POKEUSR(callee-reg) from a tracer.
* Issue related to multiple syscall restarts are addressed in next patch
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Jonas Bonn <jonas@southpole.se>
ARC700 includes 2 in-core 32bit timers TIMER0 and TIMER1.
Both have exactly same capabilies.
* programmable to count from TIMER<n>_CNT to TIMER<n>_LIMIT
* for count 0 and LIMIT ~1, provides a free-running counter by
auto-wrapping when limit is reached.
* optionally interrupt when LIMIT is reached (oneshot event semantics)
* rearming the interrupt provides periodic semantics
* run at CPU clk
ARC Linux uses TIMER0 for clockevent (periodic/oneshot) and TIMER1 for
clocksource (free-running clock).
Newer cores provide RTSC insn which gives a 64bit cpu clk snapshot hence
is more apt for clocksource when available.
SMP poses a bit of challenge for global timekeeping clocksource /
sched_clock() backend:
-TIMER1 based local clocks are out-of-sync hence can't be used
(thus we default to jiffies based cs as well as sched_clock() one/both
of which platform can override with it's specific hardware assist)
-RTSC is only allowed in SMP if it's cross-core-sync (Kconfig glue
ensures that) and thus usable for both requirements.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
This includes support for generic clone/for/vfork/execve
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Hand optimised asm code for ARC700 pipeline.
Originally written/optimized by Joern Rennecke
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Joern Rennecke <joern.rennecke@embecosm.com>
* L1_CACHE_SHIFT
* PAGE_SIZE, PAGE_OFFSET
* struct pt_regs, struct user_regs_struct
* struct thread_struct, cpu_relax(), task_pt_regs(), start_thread(), ...
* struct thread_info, THREAD_SIZE, INIT_THREAD_INFO(), TIF_*, ...
* BUG()
* ELF_*
* Elf_*
To disallow user-space visibility into some of the core kernel data-types
such as struct pt_regs, #ifdef __KERNEL__ which also makes the UAPI header
spit (further patch in the series) to NOT export it to asm/uapi/ptrace.h
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Jonas Bonn <jonas.bonn@gmail.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Override asm-generic implementations. We basically gain on 2 fronts
* checks for alignment no longer needed as we are only doing "unit"
sized copies.
(Careful observer could argue that While the kernel buffers are aligned,
the user buffer in theory might not be - however in that case the
user space is already broken when it tries to deref a hword/word
straddling word boundary - so we are not making it any worse).
* __copy_{to,from}_user( ) returns bytes that couldn't be copied,
whereas get_user() returns 0 for success or -EFAULT (not size). Thus
the code to do leftover bytes calculation can be avoided as well.
The savings were significant: ~17k of code.
bloat-o-meter vmlinux_uaccess_pre vmlinux_uaccess_post
add/remove: 0/4 grow/shrink: 8/118 up/down: 1262/-18758 (-17496)
^^^^^^^^^
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This covers the UP / SMP (with no hardware assist for atomic r-m-w) as
well as ARC700 LLOCK/SCOND insns based.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC700 has an in-core intc which provides 2 priorities (a.k.a.) "levels"
of interrupts (per IRQ) hencforth referred to as L1/L2 interrupts.
CPU flags register STATUS32 has Interrupt Enable bits per level (E1/E2)
to globally enable (or disable) all IRQs at a level. Hence the
implementation of arch_local_irq_{save,restore,enable,disable}( )
The STATUS32 reg can be r/w only using the AUX Interface of ARC, hence
the use of LR/SR instructions. Further, E1/E2 bits in there can only be
updated using the FLAG insn.
The intc supports 32 interrupts - and per IRQ enabling is controlled by
a bit in the AUX_IENABLE register, hence the implmentation of
arch_{,un}mask_irq( ) routines.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Arnd in his review pointed out that arch Kconfig organisation has several
deficiencies:
* Build time entries for things which can be runtime extracted from DT
(e.g. SDRAM size, core clk frequency..)
* Not multi-platform-image-build friendly (choice .. endchoice constructs)
* cpu variants support (750/770) is exclusive.
The first 2 have been fixed in subsequent patches.
Due to the nature of the 750 and 770, it is not possible to build for
both together, w/o special runtime glue code which would hurt
performance.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
