We require that all archs implement atomic_cmpxchg(), for the generic
version of atomic_add_unless().
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When pages are onlined, not only zone->present_pages but also
pgdat->node_present_pages should be refreshed.
This parameter is used to show information at
/sys/device/system/node/nodeX/meminfo via si_meminfo_node().
So, it shows strange value for MemUsed which is calculated
(node_present_pages - all zones free pages).
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC is still causing a few problems and the code is relatively green. Mark
it as experimental until thing settle down.
Also, provide some documentation pointers in Kconfig help.
Signed-off-by: Tim Small <tim@buttersideup.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the code tries up to spin_retry times to grab a lock using the cs
instruction. The cs instruction has exclusive access to a memory region
and therefore invalidates the appropiate cache line of all other cpus. If
there is contention on a lock this leads to cache line trashing. This can
be avoided if we first check wether a cs instruction is likely to succeed
before the instruction gets actually executed.
Signed-off-by: Christian Ehrhardt <ehrhardt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kobject_put() can free the memory at *cmd, but cmd->lock points to a
persistent lock that is not freed with cmd.
Signed-off-by: Max Asbock <masbock@us.ibm.com>
Cc: Vernon Mauery <vernux@us.ibm.com>
Cc: Srihari Vijayaraghavan <sriharivijayaraghavan@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the process has already set PF_MALLOC and is already using
current->reclaim_state then do not try to reclaim memory from the zone.
This is set by kswapd and/or synchrononous global reclaim which will not
take it lightly if we zap the reclaim_state.
Signed-off-by: Christoph Lameter <clameter@sig.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- wrong test for 'is this a BARRIER bio'
- not freeing on all possible paths.
- using r1_bio after freeing it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
/usr/src/ctest/git/kernel/mm/rmap.c: In function `page_referenced_one':
/usr/src/ctest/git/kernel/mm/rmap.c:354: warning: implicit declaration of function `rwsem_is_locked'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some bugs in mtd/jffs2 on 64bit platform.
The MEMGETBADBLOCK/MEMSETBADBLOCK ioctl are not listed in compat_ioctl.h.
And some variables in jffs2 are declared as uint32_t but used to hold
size_t values.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a lockup which was introduced during the conversion to the generic IRQ
framework.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ERR_PTR() is supposed to be passed a negative value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
smi_data_buf_free() references dcdbas_pdev when calling
dma_free_coherent(). In dcdbas_exit(), smi_data_buf_free() is called after
platform_device_unregister(dcdbas_pdev).
This patch moves platform_device_unregister(dcdbas_pdev) after
smi_data_buf_free() in dcdbas_exit().
Signed-off-by: Doug Warzecha <Douglas_Warzecha@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove two early-development BUG_ONs from page_add_file_rmap.
The pfn_valid test (originally useful for checking that nobody passed an
artificial struct page) comes too late, since we already have the struct
page.
The PageAnon test (useful when anon was first distinguished from file rmap)
prevents ->nopage implementations from reusing ->mapping, which would
otherwise be available.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is gluing the build of cirrusfb but really the mess that would need
cleaning and fixing is <video/vga.h> and <linux/vt_buffer.h> ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
At times gcc will place bits of __exit functions into .rodata. If
compiled into the kernle itself we used to discard .exit.text - but
not the bits left in .rodata. While harmless this did at times result
in a large number of warnings. So until gcc fixes this, discard
.exit.text at runtime.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In case a particular system doesn't support highmem the runtime checks
will ensure nothing bad is going to happen.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
What: Support for NEC DDB5074 and DDB5476 evaluation boards.
When: June 2006
Why: Board specific code doesn't build anymore since ~2.6.0 and no
users have complained indicating there is no more need for these
boards. This should really be considered a last call.
Who: Ralf Baechle <ralf@linux-mips.org>
The low level PCI DMA mapping functions should handle it in most cases.
This should fix problems with depleting the DMA zone early. The old
code used precious GFP_DMA memory in many cases where it was not needed.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ATI chipsets tend to generate double timer interrupts for the local APIC
timer when both the 8254 and the IO-APIC timer pins are enabled. This is
because they route it to both and the result is anded together and the CPU
ends up processing it twice.
This patch changes check_timer to disable the 8254 routing for interrupt 0.
I think it would be safe on all chipsets actually (i tested it on a couple
and it worked everywhere) and Windows seems to do it in a similar way, but
to be conservative this patch only enables this mode on ATI (and adds
options to enable/disable too)
Ported over from a similar x86-64 change.
I reused the ACPI earlyquirk infrastructure for the ATI bridge check, but
tweaked it a bit to work even without ACPI.
Inspired by a patch from Chuck Ebbert, but redone.
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent change to compat. dev_ifconf() in fs/compat_ioctl.c
causes ifconf data to be truncated 1 entry too early when copying it
to userspace. The correct amount of data (length) is returned,
but the final entry is empty (zero, not filled in).
The for-loop 'i' check should use <= to allow the final struct
ifreq32 to be copied. I also used the ifconf-corruption program
in kernel bugzilla #4746 to make sure that this change does not
re-introduce the corruption.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing kexec and kdump we hit problems where the new kernel would
freeze or instantly reboot. The easiest way to trigger it was to kexec a
kernel compiled for CONFIG_M586 on an athlon cpu. Compiling for CONFIG_MK7
instead would work fine.
The patch fixes a few problems with the kexec inline asm.
Signed-off-by: Chris Mason <mason@suse.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Tested-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kmem_cache_init() incorrectly assumes that the cache_cache object will fit
in an order 0 allocation. On very large systems, this is not true. Change
the code to try larger order allocations if order 0 fails.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Miscellaneous fixes related to accessing uninitialized variables or memory
that was already freed.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Cc: Eric Van Hensbergen <ericvh@ericvh.myip.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The x86_model calculation also applies for family 6. early_cpu_detect
does the right thing, but generic_identify misses.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DASD allows to open a device as soon as gendisk is registered, which means the
device is a fake device (capacity=0) and we do know nothing about blocksize
and partitions at that point of time. In case the device is opened by
someone, the bdev and inode creation is done with the fake device info and the
following partition detection code is just using the wrong data.
To avoid this modify the DASD state machine to make sure that the open is
rejected until the device analysis is either finished or an unformatted device
was detected.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The message limit on the iucv connect call for the smsg module is too low.
Therefore increase the smsg message limit to 255.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
strnlen_user is supposed to return then length count + 1 if no terminating \0
is found, and it should return 0 on exception. Found by David Howells
<dhowells@redhat.com>.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have benchmarked this on an x86_64 NUMA system and see no significant
performance difference on kernbench. Tested on both x86_64 and powerpc.
The way we do file struct accounting is not very suitable for batched
freeing. For scalability reasons, file accounting was
constructor/destructor based. This meant that nr_files was decremented
only when the object was removed from the slab cache. This is susceptible
to slab fragmentation. With RCU based file structure, consequent batched
freeing and a test program like Serge's, we just speed this up and end up
with a very fragmented slab -
llm22:~ # cat /proc/sys/fs/file-nr
587730 0 758844
At the same time, I see only a 2000+ objects in filp cache. The following
patch I fixes this problem.
This patch changes the file counting by removing the filp_count_lock.
Instead we use a separate percpu counter, nr_files, for now and all
accesses to it are through get_nr_files() api. In the sysctl handler for
nr_files, we populate files_stat.nr_files before returning to user.
Counting files as an when they are created and destroyed (as opposed to
inside slab) allows us to correctly count open files with RCU.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds new tunables for RCU queue and finished batches. There are
two types of controls - number of completed RCU updates invoked in a batch
(blimit) and monitoring for high rate of incoming RCUs on a cpu (qhimark,
qlowmark).
By default, the per-cpu batch limit is set to a small value. If the input
RCU rate exceeds the high watermark, we do two things - force quiescent
state on all cpus and set the batch limit of the CPU to INTMAX. Setting
batch limit to INTMAX forces all finished RCUs to be processed in one shot.
If we have more than INTMAX RCUs queued up, then we have bigger problems
anyway. Once the incoming queued RCUs fall below the low watermark, the
batch limit is set to the default.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement percpu_counter_sum(). This is a more accurate but slower version of
percpu_counter_read_positive().
We need this for Alex's speedup-ext3_statfs patch and for the nr_file
accounting fix. Otherwise these things would be too inaccurate on large CPU
counts.
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Cc: Alex Tomas <alex@clusterfs.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix i386 nmi_watchdog that does not meet watchdog timeout condition. It
does not hit die_nmi when it should be triggered, because the current
nmi_watchdog_tick in arch/i386/kernel/nmi.c never count up alert_counter
like this:
void nmi_watchdog_tick (struct pt_regs * regs) {
if (last_irq_sums[cpu] == sum) {
alert_counter[cpu]++; <- count up alert_counter, but
if (alert_counter[cpu] == 5*nmi_hz)
die_nmi(regs, "NMI Watchdog detected LOCKUP");
alert_counter[cpu] = 0; <- reset alert_counter
This patch changes it back to the previous and working version.
This was found and originally written by Kohta NAKASHIMA.
(akpm: also uninline write_watchdog_counter(), saving 184 byets)
Signed-off-by: GOTO Masanori <gotom@sanori.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the 'ptr' is a const, this code cause "assignment of read-only variable"
error on gcc 4.x.
Use __u64 instead of __typeof__(*(ptr)) for temporary variable to get
rid of errors on gcc 4.x.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Idle threads should have a sane ->timestamp value, to avoid init kernel
thread(s) from inheriting it and causing miscalculations in
try_to_wake_up().
Reported-by: Mike Galbraith <efault@gmx.de>.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug in udf where it would write uid/gid = 0 to the disk for files
owned by the id given with the uid=/gid= mount options. It also adds 4 new
mount options: uid/gid=forget and uid/gid=ignore. Without any options the
id in core and on disk always match. Giving uid/gid=nnn specifies a
default ID to be used in core when the on disk ID is -1. uid/gid=ignore
forces the in core ID to allways be used no matter what the on disk ID is.
uid/gid=forget forces the on disk ID to always be written out as -1.
The use of these options allows you to override ownerships on a disk or
disable ownwership information from being written, allowing the media to be
used portably between different computers and possibly different users
without permissions issues that would require root to correct.
Signed-off-by: Phillip Susi <psusi@cfl.rr.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the mm/mempolicy.c build for !CONFIG_HUGETLB_PAGE.
Cc: Christoph Lameter <clameter@engr.sgi.com>
Cc: Martin Bligh <mbligh@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We're presently getting oopses because Bluetooth (and possibly other) drivers
are calling core functions after things have been shut down.
So rather than oopsing, let's drop a warning then take avoiding action, so the
machine survives. Once all the sub-drivers are fixed up we can remove the
take-avoiding-action part.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We fixed this:
arch/powerpc/platforms/pseries/eeh.c: In function `eeh_add_device_tree_late':
arch/powerpc/platforms/pseries/eeh.c:901: warning: implicit declaration of function `eeh_add_device_late'
arch/powerpc/platforms/pseries/eeh.c: At top level:
arch/powerpc/platforms/pseries/eeh.c:918: error: conflicting types for 'eeh_add_device_late'
arch/powerpc/platforms/pseries/eeh.c:901: error: previous implicit declaration of 'eeh_add_device_late' was here
make[2]: *** [arch/powerpc/platforms/pseries/eeh.o] Error 1
But we forgot the !CONFIG_EEH stub.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] mca recovery return value when no bus check
[IA64] SGI SN drivers: don't report !sn2 hardware as an error
[IA64] don't report !sn2 or !summit hardware as an error
[IA64] gensparse_defconfig: turn on PNPACPI
[IA64] Increase severity of MCA recovery messages
