Handle .reset_resume() so that libertas can survive suspend/resume without
reloading the firmware.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Deepak Saxena <dsaxena@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the problem to keep mac80211 resubmitting SKBs
when Tx request cannot be met in monitor mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the rates reported in monitor mode operation
(Wireshark) for iwlwifi.
Previously, packets with rates of 6M..24M would be reported
incorrectly and packets with rates of 36M..54M would not passed
up the stack.
Signed-off-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite AID calculation in handle_pspoll() to avoid truncating bits.
Make hostap_80211_header_parse() static, don't export it. Avoid
shadowing variables.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DEBUG_EXTRA is reported to the kernel log by default, but DEBUG_EXTRA2
is not. Unrelated WDS frames pollute the log unnecessarily.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
clock is already cpu-endian (see le32_to_cpu slightly before), so
le64_to_cpu doesn't make much sense.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a circular locking dependency in the workqueue handling.
The interface work task uses the mac80211 function
ieee80211_iterate_active_interfaces() which grabs the RTNL lock.
However when the interface is brough down, this happens under the RTNL
lock as well, this causes problems because mac80211 will flush the workqueue
during the ifdown event. This causes mac80211 to wait until the driver has
completed all work which can't finish because it is waiting on the RTNL lock.
This is fixed by moving rt2x00 workqueue tasks on a different workqueue,
this workqueue can be flushed when the ieee80211_hw structure is removed
by the driver (when the driver is unloaded) which does not happen under the
RTNL lock.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies the band selection management when scanning, so
bands are now scanned according to HW band support.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usb_cache_mutex was not correctly released
under all circumstances. Both rt73usb as rt2500usb
didn't release the mutex under certain conditions
when the register access failed. Obviously such
failure would lead to deadlocks.
In addition under similar circumstances when the
bbp register couldn't be read the value must be
set to 0xff to indicate that the value is wrong.
This too didn't happen under all circumstances.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible MMIO access while the device is still down
from a suspend cycle. MMIO accesses with the device powered down
may cause crashes on certain devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Never return TX_BUSY from op_tx. It doesn't make sense to return
TX_BUSY, if we can not transmit the packet.
Drop the packet and return TX_OK.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Never return TX_BUSY from op_tx. It doesn't make sense to return
TX_BUSY, if we can not transmit the packet.
Drop the packet and return TX_OK.
This will fix the resume hang.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.
The alternative is to select NEW_LEDS, which some drivers do.
This patch fixes the led_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.
This patch fixes the input_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes a WARN_ON that is responsible for the following koops:
http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample
The comment in the patch describes why it's safe to simply remove
the check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
This patch moves the whole struct b43_dmaring struct initialization
right before any DMA allocation operation.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
fix race between:
ieee80211_open->ieee80211_led_radio->led_trigger_event->led_set_brightness->iwl3945_led_brightness_set
(which assumes that "led->priv" is not NULL)
and
iwl3945_pci_probe->iwl3945_setup_deferred_work->(...)->iwl3945_bg_alive_start->iwl3945_alive_start->iwl3945_led_register->iwl3945_led_register_led
which sets priv field in struct iwl3945_led
after
led->led_dev.brightness_set = iwl3945_led_brightness_set;
(...)
led_classdev_register(device, &led->led_dev);
http://kerneloops.org/guilty.php?guilty=iwl3945_led_brightness_set&version=2.6.25-release&start=1671168&end=1703935&class=oops
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: ipw3945-devel@lists.sourceforge.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a data alignment issue in the zd1211rw driver.
The IEEE80211_STYPE_QOS_DATA bit should be used as a bitwise test
to test for the presence of the 2 byte QoS control field.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes an issus that made "iwconfig eth1 power on" non-working.
When we get a "PS sleep" event, we have to confirm this to the firmware.
The confirm happens with a command, but this command is special: the
firmware won't send us a response. if_cs_host_to_card() is setting
priv->dnld_sent anyway, so this variable stayed at DNLD_DATA_SENT and
was never cleared back.
Now I put the special knowledge that the CMD_802_11_PS_MODE with
CMD_SUBCMD_SLEEP_CONFIRMED doesn't need to need a response by directly
clearing the dnld_sent state in lbs_send_confirmsleep().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When another scan is in progress, a direct scan gets dropped on the
floor. However, that direct scan is usually the scan that's really
needed by userspace, and gets stomped on by all the broadcast scans the
ipw2200 driver issues internally. Make sure the direct scan happens
eventually, and as a bonus ensure that the passive scan worker is
cleaned up when appropriate.
The change of request_passive_scan form a struct work to struct
delayed_work is only to make the set_wx_scan() code a bit simpler, it's
still only used with a delay of 0 to match previous behavior.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the Philips CPWUA054/00 in p54usb.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there are no networks on the free list, expire the oldest one when
creating a new adhoc network. Because ipw2200 and the ieee80211 stack
don't actually cull old networks and place them back on the free list
unless they are needed for new probe responses, over time the free list
would become empty and creating an adhoc network would fail due to the !
list_empty(...) check.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: space prohibited between function name and open parenthesis '('
#22: FILE: drivers/net/wireless/airo.c:2907:
+ while ((IN4500 (ai, COMMAND) & COMMAND_BUSY) && (delay < 10000)) {
total: 0 errors, 1 warnings, 8 lines checked
./patches/wireless-airo-waitbusy-wont-delay.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Dan Williams <dcbw@redhat.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Range check for power_output were missing.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a case that a wrong maximal rate is selected when
searching for better configurations.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When exiting from stay in table state (e.g. timer expiration),
all the statistics are reset and the RS flow should not continue
but only after enough statistics are collected again.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the rndis_wlan driver to connect to TKIP PSK
networks. It uses the ASSOCIATION_INFORMATION RNDIS call to pull back
the IEs and sends them back to userspace using wireless events. Tested
on a few wireless networks I have access to. Based on the similar
code in ndiswrapper.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
[edit: cleanups]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_beacondone() is called from interrupt context,
this means we cannot use the mac80211 interface iterator
that uses the rtnl lock (since that uses a mutex which can sleep).
Instead we should use the atomic mac80211 interface iterator.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the antenna configuration has changed we should reset
the antenna RSSI value. Otherwise the value will be influenced
by the previous configuration quality which in turn will affect
the antenna diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link quality estimation became quite low for all rt2x00 drivers
because the number of retries it took to send the frame were
counted as failure.
This does not correspond to the legacy driver link quality calculation,
by not counting it we will send somewhat more optimistic values to
mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the tx() handler runs while the device has disapeared,
we did return NETDEV_TX_OK but didn't free the skb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This updates the beacon template code to upload both templates,
if we never uploaded one before.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The grf5101 RF code needs to invoke grf5101_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The max2820 RF code needs to invoke max2820_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sa2400 RF code needs to invoke sa2400_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The static function max2820_rf_set_channel is called with conf == NULL
within its compilation unit. Originally this defaulted to b/g channel
1, but "cfg80211 API for channels/bitrates, mac80211 and driver
conversion" (commit 8318d78a44) mistakenly
dropped this check. This patch minimally restores the expected
behavior.
Reported-by: Colin Lai <colin_sh@163.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: The world is not perfect patch.
tcp: Make prior_ssthresh a u32
xfrm_user: Remove zero length key checks.
net/ipv4/arp.c: Use common hex_asc helpers
cassini: Only use chip checksum for ipv4 packets.
tcp: TCP connection times out if ICMP frag needed is delayed
netfilter: Move linux/types.h inclusions outside of #ifdef __KERNEL__
af_key: Fix selector family initialization.
libertas: Fix ethtool statistics
mac80211: fix NULL pointer dereference in ieee80211_compatible_rates
mac80211: don't claim iwspy support
orinoco_cs: add ID for SpeedStream wireless adapters
hostap_cs: add ID for Conceptronic CON11CPro
rtl8187: resource leak in error case
ath5k: Fix loop variable initializations
Fix various problems:
- We converted MESH_ACCESS to a direct command but missed this caller.
- We were trying to access mesh stats even on meshless firmware.
- We should really zero the buffer if something goes wrong.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
