Commit Graph

25 Commits

Author SHA1 Message Date
Michael Chan
28fbef78a4 [PATCH] tg3: fix ASF heartbeat
Change the ASF heart beat to 5 seconds for faster detection of system
crash. The driver sends the heartbeat every 2 seconds and the ASF
firmware will timeout and reset the device if no heartbeat is received
after 5 seconds. The old scheme of 2 minutes is ineffective.

tg3_write_mem_fast() is added to speed up the IO to send the heartbeat.
When no workaround is needed, it will use direct MMIO to memory space
to write to memory.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-10-28 16:07:30 -04:00
Michael Chan
a4e2b34784 [PATCH] tg3: add 5714/5715 support
Add complete support for 5714/5715. These chips are very similar to
5780 so the changes are very trivial. A TG3_FLG2_5780_CLASS flag is
added to identify these chips.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-10-28 16:07:29 -04:00
Michael Chan
c94e39418a [TG3]: 5780 PHY fixes
Fix 5780 PHY related problems:

1. MAC_RX_MODE reset must be done before setting up the MAC_MODE
   register on 5705_PLUS chips or the chip will stop receiving after
   a while. The MAC_RX_MODE reset is needed to prevent intermittently
   losing the first receive packet on serdes chips.

2. Skip MAC loopback test on 5780 because of hardware errata. Normal
   traffic including PHY loopback is not affected by the errata.

3. PHY loopback fails intermittently on 5708S and this is fixed by
   putting the PHY in loopback mode first before programming the MAC
   mode register. A MAC_RX_MODE reset is also added.

4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow
   nway_reset if 5780S is in parallel detect mode.

5. Add missing PHY IDs in KNOWN_PHY_ID() macro.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-09-27 12:12:42 -07:00
Michael Chan
6892914fb7 [TG3]: Add indirect register method for 5703 behind ICH
This patch adds the new workaround for 5703 A1/A2 if it is behind
certain ICH bridges. The workaround disables memory and uses config.
cycles only to access all registers. The 5702/03 chips can mistakenly
decode the special cycles from the ICH chipsets as memory write cycles,
causing corruption of register and memory space. Only certain ICH
bridges will drive special cycles with non-zero data during the address
phase which can fall within the 5703's address range. This is not an ICH
bug as the PCI spec allows non-zero address during special cycles.
However, only these ICH bridges are known to drive non-zero addresses
during special cycles.

The indirect_lock is also changed to spin_lock_irqsave from spin_lock_bh
because it is used in irq handler when using the indirect method to
disable interrupts.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-08-29 15:50:42 -07:00
Michael Chan
09ee929ccc [TG3]: Add mailbox read method
This patch adds the mailbox read method and also adds an inline function
tw32_mailbox_f() for mailbox writes that require read flush.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-08-29 15:50:38 -07:00
Michael Chan
2009493065 [TG3]: Add basic register access function pointers
This patch adds the basic function pointers to do register accesses in
the fast path. This was suggested by David Miller. The idea is that
various register access methods for different hardware errata can easily
be implemented with these function pointers and performance will not be
degraded on chips that use normal register access methods.

The various register read write macros (e.g. tw32, tr32, tw32_mailbox)
are redefined to call the function pointers.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-08-29 15:50:12 -07:00
Michael Chan
747e8f8bff [TG3]: add 5780 fiber support
Add 5780S support by adding a new tg3_setup_fiber_mii_phy() function and
a timer function for parallel link detection. 5780S uses standard MII
registers for 1000BaseX and runs in GMII mode as opposed to TBI mode on
older serdes chips.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-25 12:33:22 -07:00
Michael Chan
fdfec1726b [TG3]: consolidate all DMA water mark settings
Consolidate all DMA watermark settings for standard and jumbo frames on
all chips in tg3_init_bufmgr_config() and add new settings for 5780.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-25 12:31:48 -07:00
Michael Chan
7e72aad48c [TG3]: add variable buffer size for standard ring
Add a new rx_pkt_buf_sz to the tg3 structure to support variable buffer
sizes on the standard ring.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-25 12:31:17 -07:00
Michael Chan
0f893dc6ec [TG3]: add 5780 basic jumbo frame support
Add basic jumbo frames support for 5780. This chip supports jumbo frames
on the standard receive ring without the jumbo ring. The
TG3_FLAG_JUMBO_ENABLE is changed to TG3_FLAG_JUMBO_RING_ENABLE to
indicate using the jumbo ring on 5704 and older chips. A new
TG3_FLG2_JUMBO_CAPABLE flag is added to indicate jumbo frames support
with or without the jumbo ring.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-25 12:30:38 -07:00
Michael Chan
4cf78e4fb6 [TG3]: add 5780 basic support
Add 5780 PCI IDs, chip IDs, and other basic support.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-25 12:29:19 -07:00
Michael Chan
d244c892c8 [TG3]: support for ethtool -C
Add support for ethtool -C with verification of user parameters.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-05 14:42:33 -07:00
David S. Miller
f47c11eecc [TG3]: Eliminate all hw IRQ handler spinlocks.
Move all driver spinlocks to be taken at sw IRQ
context only.

This fixes the skb_copy() we were doing with hw
IRQs disabled (which is illegal and triggers a
BUG() with HIGHMEM enabled).  It also simplifies
the locking all over the driver tremendously.

We accomplish this feat by creating a special
sequence to synchronize with the hw IRQ handler
using a binary state and synchronize_irq().
This idea is from Herbert Xu.

Thanks to Michael Chan for helping to track down
all of the race conditions in initial versions
of this code.

Signed-off-by: David S. Miller <davem@davemloft.net>
2005-06-24 20:18:35 -07:00
David S. Miller
15f9850d3c [TG3]: Set minimal hw interrupt mitigation.
Even though we do software interrupt mitigation
via NAPI, it still helps to have some minimal
hw assisted mitigation.

This helps, particularly, on systems where register
I/O overhead is much greater than the CPU horsepower.

For example, it helps on NUMA systems.  In such cases
the PIO overhead to disable interrupts for NAPI accounts
for the majority of the packet processing cost.  The
CPU is fast enough such that only a single packet is
processed by each NAPI poll call.

Thanks to Michael Chan for reviewing this patch.

Signed-off-by: David S. Miller <davem@davemloft.net>
2005-05-18 22:49:26 -07:00
David S. Miller
fac9b83ea7 [TG3]: Add tagged status support.
When supported, use the TAGGED interrupt processing support
the chip provides.  In this mode, instead of a "on/off" binary
semaphore, an incrementing tag scheme is used to ACK interrupts.

All MSI supporting chips support TAGGED mode, so the tg3_msi()
interrupt handler uses it unconditionally.  This invariant is
verified when MSI support is tested.

Since we can invoke tg3_poll() multiple times per interrupt under
high packet load, we fetch a new copy of the tag value in the
status block right before we actually do the work.

Also, because the tagged status tells the chip exactly which
work we have processed, we can make two optimizations:

1) tg3_restart_ints() need not check tg3_has_work()
2) the tg3_timer() need not poke the chip 10 times per
   second to keep from losing interrupt events

Based upon valuable feedback from Michael Chan <mchan@broadcom.com>

Signed-off-by: David S. Miller <davem@davemloft.net>
2005-05-18 22:46:34 -07:00
Michael Chan
88b06bc26b [TG3]: Add msi support
Add MSI support for 5751 C0 and 5752.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 17:13:25 -07:00
Michael Chan
e6af301be3 [TG3]: Add nvram lock-out support for 5752 TPM
Add support for the NVRAM lock-out feature for TPM in 5752. If lock-out
is enabled, certain NVRAM registers cannot be written to.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 17:12:05 -07:00
Michael Chan
361b4ac29b [TG3]: Add nvram detection for 5752
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 17:11:21 -07:00
Michael Chan
3e7d83bc96 [TG3]: Add GPIO3 for 5752
Add bit definitions for the new GPIO3 in 5752. GPIO3 must be driven as
output when it is unused.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 17:10:36 -07:00
Michael Chan
ff645bec52 [TG3]: Workaround 5752 A0 chip ID
The 5752 A0 chip ID is wrong in hardware. The simplest way to workaround
it is to change it to the correct value in tp->pci_chip_rev_id. This
way, it is easier to check for the ASIC_REV_5752 in the rest of the
driver.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 17:09:53 -07:00
Michael Chan
85e94cedc4 [TG3]: Minor 5752 fixes
Some minor 5752 fixes mostly for correctness and add 5752 PHY ID.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 17:05:28 -07:00
John W. Linville
053d78000b [TG3]: add support for bcm5752 rev a1
Replace existing ASIC_REV_5752 definition with ASIC_REV_5752_A0,
and add definition for ASIC_REV_5752_A1. Then, add ASIC_REV_5752_A1
to check for setting TG3_FLG2_5750_PLUS in tg3_get_invariants.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 17:03:52 -07:00
John W. Linville
6708e5cc10 [TG3]: define TG3_FLG2_5750_PLUS flag
Define TG3_FLG2_5750_PLUS flag and set it in tg3_get_invariants for
ASIC_REV_5750 or ASIC_REV_5752.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 17:00:52 -07:00
John W. Linville
2052da9460 [TG3]: add basic bcm5752 support
Add ASIC_REV_5752 definition.

Track-down all references to ASIC_REV_5750 and mirror them with
references to the newly defined ASIC_REV_5752.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-04-21 16:56:08 -07:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00