The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured.
This patch configures them as output pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.
So remove the muxing for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in
the board files, but CT_CP_HPD, which is used to enable/disable HPD
functionality.
This patch renames the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of freeing the GPIOs individually, use gpio_free_array().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Disables the internal pull resistor for SDA and SCL which are enabled by
default, as there are external pull up's in 4460 and 4430 ES2.3
SDP, Blaze and Panda Boards, It is done to avoid the EDID read failure.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move duplicate HDMI mux_init code from omap4 and panda board file
to display file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 10299e2e4e (ARM: RX-51:
Enable isp1704 power on/off) added power management for isp1704.
However, the transceiver should be powered on by default,
otherwise USB doesn't work at all for networking during
boot.
All kernels after v3.0 are affected.
Cc: stable@kernel.org
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commits 09d28d ("ARM: OMAP: mcbsp: Start generalize omap2_mcbsp_set_clks_src")
and 7bc0c4 ("ARM: OMAP: mcbsp: Start generalize signal muxing functions")
incorrectly set two struct omap_mcbsp_platform_data fields after
omap_device_build_ss and kfree calls.
Fix this by moving these pdata assignments before those calls.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix below compilation failure on mainline kernel 3.2-rc1
when omap_l3_noc.c is built as module.
arch/arm/mach-omap2/omap_l3_noc.c:240: error: expected ',' or ';' before 'MODULE_DEVICE_TABLE'
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The file arch/arm/mach-omap2/io.h is empty, so we can remove it.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch selects ARM_AMBA if OMAP3_EMU is defined because
OC_ETM depends on ARM_AMBA, so fix the link failure[1].
[1],
arch/arm/kernel/built-in.o: In function `etm_remove':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:609: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etb_remove':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:409: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etm_init':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:640: undefined
reference to `amba_driver_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:646: undefined
reference to `amba_driver_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:648: undefined
reference to `amba_driver_unregister'
arch/arm/kernel/built-in.o: In function `etm_probe':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:545: undefined
reference to `amba_request_regions'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:595: undefined
reference to `amba_release_regions'
arch/arm/kernel/built-in.o: In function `etb_probe':
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:347: undefined
reference to `amba_request_regions'
/home/tom/git/omap/linux-2.6-omap/arch/arm/kernel/etm.c:392: undefined
reference to `amba_release_regions'
arch/arm/mach-omap2/built-in.o: In function `emu_init':
/home/tom/git/omap/linux-2.6-omap/arch/arm/mach-omap2/emu.c:62:
undefined reference to `amba_device_register'
/home/tom/git/omap/linux-2.6-omap/arch/arm/mach-omap2/emu.c:63:
undefined reference to `amba_device_register'
make: *** [.tmp_vmlinux1] Error 1
making modules
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a bug which has been on this driver since
it was added by the original commit 984aa6db
which would never clear IRQSTATUS bits.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current code registers voltage layer details for TWL PMIC even when a TWL
has not been registered. Fix this to only register the TWL with voltage
layer when the TWL PMIC is initialized by board-level code.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
The address spaces, irqs and dma reqs count APIs return the
number of corresponding entries in a hwmod including a additional
null value or a -1 terminator in the structure introduced recently.
More information here:
- 212738a4: omap_hwmod: use a terminator record with omap_hwmod_mpu_irqs
arrays
- 78183f3f: omap_hwmod: use a null structure record to terminate
omap_hwmod_addr_space arrays
- bc614958: omap_hwmod: use a terminator record with omap_hwmod_dma_info
arrays
The issue with irqs and dma info was originally reported by Benoit Cousson.
The devices which have multiple hwmods and use device_build_ss are
broken with this, as their resources are populated with a extra null
value, subsequently the probe fails. So fix the API not to include
the array terminator in the count.
Reported-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimar@ti.com>
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP2/3 dss_core has a reset status flag in sysstatus register. Add
SYSS_HAS_RESET_STATUS flag to HWMOD data so it can be used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 HWMOD data currently contains errors with DSS clocks:
dss_hdmi and dss_venc have their main_clks wrong. The clocks should be
dss_48mhz_clk and dss_tv_clk, respectively.
These problems were temporarily fixed with the DSS patches
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), and df5d3ed23c ("OMAP:
DSS2: HDMI: fix hdmi clock name"), which can be reverted after this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This causes the HWMOD frameworks boot-time
reset to fail, possibly leaving the DSS hardware in undefined state.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core. The flag
is actually not used on OMAP4, because dss_core hardware does not have
soft-reset functionality and thus the HWMOD framework never resets nor
waits for the reset to finish.
However, while the flag is not strictly needed currently, I think it
represents the HW correctly: all the DSS clocks should be enabled after
power-on to allow DSS hardware to finish its reset.
A custom reset function will be added in the following patches which
manages this correctly for OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the dss_dss_clk from dss_core's opt-clocks. dss_dss_clk already
defined as the dss main_clk, and thus is not needed as an opt-clock.
Remove opt-clocks for dss_dispc, as dispc only uses the main_clk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 HWMOD data currently contains these errors with DSS clocks:
- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
calculate timings
- dss_dsi is missing ick and sys_clk
- dss_venc is missing dss_96m_fck opt-clock, which is required on
OMAP3430
- dss_venc's interface and main clocks are wrong, causing VENC to fail
to start
These problems were temporarily fixed with a DSS patch
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.
dss_core's opt-clocks is also missing dss_96m_fck, which is a DSS clock
present only on OMAP3430, and thus required on OMAP3430 to finish the
reset.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET and adds the dss_96m_fck
opt-clock for dss_core in OMAP3 HWMOD data, fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP2xxx HWMOD data currently contains two errors with DSS clocks:
- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
calculate timings
- dss_venc's interface and main clocks are wrong, causing VENC to fail
to start
These problems were temporarily fixed with a DSS patch
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core in OMAP2xxx
HWMOD data, fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 32aaeffbd4 (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:
$ grep -rl ^MODULE_ arch/arm/*omap*/*.c | xargs \
grep -L linux/module.h
arch/arm/mach-omap2/dsp.c
arch/arm/mach-omap2/mailbox.c
arch/arm/mach-omap2/omap-iommu.c
arch/arm/mach-omap2/smartreflex.c
Also check we either have export.h or module.h included
for the files exporting symbols:
$ grep -rl EXPORT_SYMBOL arch/arm/*omap*/*.c | xargs \
grep -L linux/export.h | xargs grep -L linux/module.h
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpuidle: Single/Global registration of idle states
cpuidle: Split cpuidle_state structure and move per-cpu statistics fields
cpuidle: Remove CPUIDLE_FLAG_IGNORE and dev->prepare()
cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
ACPI: Fix CONFIG_ACPI_DOCK=n compiler warning
ACPI: Export FADT pm_profile integer value to userspace
thermal: Prevent polling from happening during system suspend
ACPI: Drop ACPI_NO_HARDWARE_INIT
ACPI atomicio: Convert width in bits to bytes in __acpi_ioremap_fast()
PNPACPI: Simplify disabled resource registration
ACPI: Fix possible recursive locking in hwregs.c
ACPI: use kstrdup()
mrst pmu: update comment
tools/power turbostat: less verbose debugging
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
This patch makes the cpuidle_states structure global (single copy)
instead of per-cpu. The statistics needed on per-cpu basis
by the governor are kept per-cpu. This simplifies the cpuidle
subsystem as state registration is done by single cpu only.
Having single copy of cpuidle_states saves memory. Rare case
of asymmetric C-states can be handled within the cpuidle driver
and architectures such as POWER do not have asymmetric C-states.
Having single/global registration of all the idle states,
dynamic C-state transitions on x86 are handled by
the boot cpu. Here, the boot cpu would disable all the devices,
re-populate the states and later enable all the devices,
irrespective of the cpu that would receive the notification first.
Reference:
https://lkml.org/lkml/2011/4/25/83
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is the first step towards global registration of cpuidle
states. The statistics used primarily by the governor are per-cpu
and have to be split from rest of the fields inside cpuidle_state,
which would be made global i.e. single copy. The driver_data field
is also per-cpu and moved.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cpuidle governor only suggests the state to enter using the
governor->select() interface, but allows the low level driver to
override the recommended state. The actual entered state
may be different because of software or hardware demotion. Software
demotion is done by the back-end cpuidle driver and can be accounted
correctly. Current cpuidle code uses last_state field to capture the
actual state entered and based on that updates the statistics for the
state entered.
Ideally the driver enter routine should update the counters,
and it should return the state actually entered rather than the time
spent there. The generic cpuidle code should simply handle where
the counters live in the sysfs namespace, not updating the counters.
Reference:
https://lkml.org/lkml/2011/3/25/52
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Convert to use matrix keyboard to remove the warning
"Please update the board to use matrix-keypad driver".
Based on similar setup in palmtc.c. Note that this
patch is compile tested only because of lack of working
hardware.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the structure since a default one is now available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 318c3e15cd
added some "fck" clock alias to timer devices that are
not needed anymore since hwmod framework will create
them automatically.
A warning was added to highlight and thus fix the redundancy.
[ 0.616424] omap_timer.1: alias fck already exists
[ 0.621948] omap_timer.2: alias fck already exists
[ 0.627380] omap_timer.3: alias fck already exists
[ 0.632781] omap_timer.4: alias fck already exists
[ 0.638214] omap_timer.5: alias fck already exists
[ 0.643615] omap_timer.6: alias fck already exists
[ 0.649078] omap_timer.7: alias fck already exists
[ 0.654479] omap_timer.8: alias fck already exists
[ 0.659881] omap_timer.9: alias fck already exists
[ 0.665283] omap_timer.10: alias fck already exists
[ 0.670776] omap_timer.11: alias fck already exists
Remove all the clkdev entries for timer fck alias.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the init of card detect pin because
omap_mux_init_gpio() is called during hsmmc initialization
for the write protect and card detect pin.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Not in use anymore.
Signed-off-by: Bjarne Steinsbo <bsteinsbo@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
get_context_loss_count functions return context loss count as u32, and
zero means an error. However, zero is also returned when context has
never been lost and could also be returned when the context loss count
has wrapped and goes to zero.
Change the functions to return an int, with negative value meaning an
error.
OMAP HSMMC code uses omap_pm_get_dev_context_loss_count(), but as the
hsmmc code handles the returned value as an int, with negative value
meaning an error, this patch actually fixes hsmmc code also.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to fix a warning with recent dmtimer changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the typo, instead it should be SDMMC1
USBC1 is not related to MMC1 I/Os
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MMC1 data line IO's are powered down in before set regulator function.
IO's should not be powered ON when regulator is OFF.
Keep the IO's in power pown mode after regulator OFF otherwise VMODE_ERROR
interrupt is generated due to mismatch in input (regulator)
voltage and MMC IO drive voltage.
Delete incorrect comments which are not applicable for OMAP4.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reported-by: Viswanath Puttagunta <vishp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit d6504acd21 ("OMAP2+: hwmod:
remove OMAP_CHIP*") tests the inverse condition of what it should be
testing for the return value from omap_hwmod_register(). This causes
several IP blocks to not be registered on several OMAP3 family devices.
Fixing that bug also unmasked another bug, originally reported by
Chase Maupin <chase.maupin@ti.com> and then subsequently by Abhilash K
V <abhilash.kv@ti.com>, which caused SmartReflex IP blocks to be
registered on SoCs that don't support them.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for comments
on a previous version of the patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Chase Maupin <chase.maupin@ti.com>
Cc: Abhilash K V <abhilash.kv@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include linux/module.h to fix below build error:
CC arch/arm/mach-omap2/omap_l3_noc.o
arch/arm/mach-omap2/omap_l3_noc.c:240: error: expected ',' or ';' before 'MODULE_DEVICE_TABLE'
arch/arm/mach-omap2/omap_l3_noc.c:250: error: 'THIS_MODULE' undeclared here (not in a function)
make[1]: *** [arch/arm/mach-omap2/omap_l3_noc.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f718e2c034 (ARM: OMAP2+: devices:
Remove all omap_device_pm_latency structures) removed these structures.
Commit 3528c58eb9 (OMAP: omap_device:
when building return platform_device instead of omap_device) now
returns platform_device instead of omap_device.
Fix up the omap-mcpdm init function since this part comes via sound
tree, and there has been changes regarding to hwmod/omap_device_build.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
When customizing omap2plus_defconfig to build for only
one board (omap3evm), I came across these warnings and
errors (filenames truncated):
arch/arm/mach-omap2/board-generic.c:76:20: warning: 'omap4_init' defined but not used
arch/arm/mach-omap2/built-in.o: In function `omap2420_init_early':
arch/arm/mach-omap2/io.c:364: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/io.c:366: undefined reference to `omap2xxx_voltagedomains_init'
arch/arm/mach-omap2/io.c:367: undefined reference to `omap242x_powerdomains_init'
arch/arm/mach-omap2/io.c:368: undefined reference to `omap242x_clockdomains_init'
arch/arm/mach-omap2/io.c:369: undefined reference to `omap2420_hwmod_init'
arch/arm/mach-omap2/built-in.o: In function `omap2430_init_early':
arch/arm/mach-omap2/io.c:376: undefined reference to `omap2_set_globals_243x'
arch/arm/mach-omap2/io.c:378: undefined reference to `omap2xxx_voltagedomains_init'
arch/arm/mach-omap2/io.c:379: undefined reference to `omap243x_powerdomains_init'
arch/arm/mach-omap2/io.c:380: undefined reference to `omap243x_clockdomains_init'
arch/arm/mach-omap2/io.c:381: undefined reference to `omap2430_hwmod_init'
arch/arm/mach-omap2/built-in.o: In function `omap4430_init_early':
arch/arm/mach-omap2/io.c:436: undefined reference to `omap2_set_globals_443x'
arch/arm/mach-omap2/io.c:438: undefined reference to `omap44xx_voltagedomains_init'
arch/arm/mach-omap2/io.c:439: undefined reference to `omap44xx_powerdomains_init'
arch/arm/mach-omap2/io.c:440: undefined reference to `omap44xx_clockdomains_init'
arch/arm/mach-omap2/io.c:441: undefined reference to `omap44xx_hwmod_init'
This patch fixes them.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Acked-by: Thomas Weber <weber@corscience.de>
[tony@atomide.com: updated to fix warnings for board-generic.c]
Signed-off-by: Tony Lindgren <tony@atomide.com>
