Commit Graph

495 Commits

Author SHA1 Message Date
Haavard Skinnemoen
4d5e392c33 [PATCH] atmel_serial: Fix roundoff error in atmel_console_get_options
The atmel_console_get_options() function initializes the baud,
parity and bits settings from the actual hardware setup, in
case it has been initialized by a e.g. boot loader.

The baud rate, however, is not necessarily exactly equal to one of
the standard baud rates (115200, etc.) This means that the baud rate
calculated by this function may be slightly higher or slightly lower
than one of the standard baud rates.

If the baud rate is slightly lower than the target, this causes
problems when uart_set_option() tries to match the detected baud rate
against the standard baud rate, as it will always select a baud rate
that is lower or equal to the target rate. For example if the
detected baud rate is slightly lower than 115200, usart_set_options()
will select 57600.

This patch fixes the problem by subtracting 1 from the value in BRGR
when calculating the baud rate. The detected baud rate will thus
always be higher than the nearest standard baud rate, and
uart_set_options() will end up doing the right thing.

Tested on ATSTK1000 and AT91RM9200-EK boards. Both are broken without
this patch.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:06 -07:00
Haavard Skinnemoen
acca9b83ac [PATCH] atmel_serial: Support AVR32
Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM-
specific code in the driver.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:06 -07:00
Haavard Skinnemoen
75d3521377 [PATCH] atmel_serial: Pass fixed register mappings through platform_data
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.

This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.

On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.

If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Haavard Skinnemoen
71f2e2b878 [PATCH] atmel_serial: Rename at91_register_uart_fns
Rename at91_register_uart_fns and associated structs and variables
to make it consistent with the atmel_ prefix used by the rest of
the driver.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Haavard Skinnemoen
9ab4f88b7f [PATCH] serial: Rename PORT_AT91 -> PORT_ATMEL
The at91_serial driver can be used with both AT32 and AT91 devices
from Atmel and has therefore been renamed atmel_serial. The only
thing left is to rename PORT_AT91 PORT_ATMEL.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Haavard Skinnemoen
7192f92c79 [PATCH] at91_serial -> atmel_serial: Internal names
Prefix all internal functions and variables with atmel_ instead of
at91_.

The at91_register_uart_fns() stuff is left as is since I can't find
any actual users of it.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Haavard Skinnemoen
73e2798b0f [PATCH] at91_serial -> atmel_serial: Public definitions
Rename the following public definitions:
  * AT91_NR_UART -> ATMEL_MAX_UART
  * struct at91_uart_data -> struct atmel_uart_data
  * at91_default_console_device -> atmel_default_console_device

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Haavard Skinnemoen
1e8ea80219 [PATCH] at91_serial -> atmel_serial: Platform device name
Rename the "at91_usart" platform driver "atmel_usart" and update
platform devices accordingly.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Haavard Skinnemoen
749c4e6033 [PATCH] at91_serial -> atmel_serial: Kconfig symbols
Rename the following Kconfig symbols:
  * CONFIG_SERIAL_AT91 -> CONFIG_SERIAL_ATMEL
  * CONFIG_SERIAL_AT91_CONSOLE -> CONFIG_SERIAL_ATMEL_CONSOLE
  * CONFIG_SERIAL_AT91_TTYAT -> CONFIG_SERIAL_ATMEL_TTYAT

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Haavard Skinnemoen
b6156b4e2e [PATCH] at91_serial -> atmel_serial: at91_serial.c
Rename at91_serial.c atmel_serial.c

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Haavard Skinnemoen
5b34821a60 [PATCH] at91_serial -> atmel_serial: at91rm9200_usart.h
Move include/asm/arch/at91rm9200_usart.h into drivers/serial and rename
it atmel_usart.h. Also delete AVR32's version of this file.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:05 -07:00
Linus Torvalds
fefd26b3b8 Merge master.kernel.org:/pub/scm/linux/kernel/git/davej/configh
* master.kernel.org:/pub/scm/linux/kernel/git/davej/configh:
  Remove all inclusions of <linux/config.h>

Manually resolved trivial path conflicts due to removed files in
the sound/oss/ subdirectory.
2006-10-04 09:59:57 -07:00
Matthew Wilcox
136ce40e9f [PARISC] Clean up asm-parisc/serial.h
Russell King pointed out that asm/serial.h is anachronistic and we were
misusing BASE_BAUD.  So fix BASE_BAUD for PCI 16550 UARTs, move LASI_BASE_BAUD
into 8250_gsc, and fix the obsolete comment about reserving serial port slots.

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2006-10-04 06:47:03 -06:00
Carlos O'Donell
e45da35e18 [PARISC] Document that D-class can also use serial_mux
Signed-off-by: Carlos O'Donell <carlos@systemhalted.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2006-10-04 06:46:11 -06:00
Dave Jones
038b0a6d8d Remove all inclusions of <linux/config.h>
kbuild explicitly includes this at build time.

Signed-off-by: Dave Jones <davej@redhat.com>
2006-10-04 03:38:54 -04:00
Uwe Zeisberger
f30c226954 fix file specification in comments
Many files include the filename at the beginning, serveral used a wrong one.

Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03 23:01:26 +02:00
Matt LaPlante
095096038d Fix several typos in drivers/
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03 22:31:37 +02:00
Linus Torvalds
6f3a28f7d1 Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial: (21 commits)
  [SERIAL] add PNP IDs for FPI based touchscreens
  [SERIAL] Magic SysRq SAK does nothing on serial consoles
  [SERIAL] tickle NMI watchdog on serial output.
  [SERIAL] Fix oops when removing suspended serial port
  [SERIAL] Fix resume handling bug
  [SERIAL] Remove wrong asm/serial.h inclusions
  [SERIAL] CONFIG_PM=n slim: drivers/serial/8250_pci.c
  [SERIAL] OMAP1510 serial fix for 115200 baud
  [SERIAL] returning proper error from serial core driver
  [SERIAL] Make uart_line_info() correctly tell MMIO from I/O port
  [SERIAL] suspend/resume handlers don't have level arg anymore
  [SERIAL] 8250 resourse management fixes
  [SERIAL] serial_cs: Add quirk for brainboxes 2-port RS232 card
  [SERIAL] serial_cs: handle Nokia multi->single port bodge via config quirk
  [SERIAL] serial_cs: add configuration quirk
  [SERIAL] serial_cs: Convert Oxford 950 / Possio GCC wakeup quirk
  [SERIAL] serial_cs: convert IBM post-init handling to a quirk
  [SERIAL] serial_cs: allow wildcarded quirks
  [SERIAL] serial_cs: convert multi-port table to quirk table
  [SERIAL] serial_cs: Use clean up multiport card detection
  ...
2006-10-03 09:13:29 -07:00
Linus Torvalds
ccaa36f735 Merge git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (29 commits)
  [POWERPC] Fix rheap alignment problem
  [POWERPC] Use check_legacy_ioport() for ISAPnP
  [POWERPC] Avoid NULL pointer in gpio1_interrupt
  [POWERPC] Enable generic rtc hook for the MPC8349 mITX
  [POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class
  [POWERPC] Create a "wrapper" script and use it in arch/powerpc/boot
  [POWERPC] fix spin lock nesting in hvc_iseries
  [POWERPC] EEH failure to mark pci slot as frozen.
  [POWERPC] update powerpc defconfig files after libata kconfig breakage
  [POWERPC] enable sysrq in pmac32_defconfig
  [POWERPC] UPIO_TSI cleanup
  [POWERPC] rewrite mkprep and mkbugboot in sane C
  [POWERPC] maple/pci iomem annotations
  [POWERPC] powerpc oprofile __user annotations
  [POWERPC] cell spufs iomem annotations
  [POWERPC] NULL noise removal: spufs
  [POWERPC] ppc math-emu needs -fno-builtin-fabs for math.c and fabs.c
  [POWERPC] update mpc8349_itx_defconfig and remove some debug settings
  [POWERPC] Always call cede in pseries dedicated idle loop
  [POWERPC] Fix loop logic in irq_alloc_virt()
  ...
2006-10-03 08:52:26 -07:00
Jeff Dike
b68e31d0eb [PATCH] const struct tty_operations
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking.  One of these
structures was a struct tty_operations.  In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.

This patch declares all struct tty_operations in the tree as const.  In all
cases, they are static and used only as input to tty_set_operations.  As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.

53 drivers are affected.  I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months.  serial_core.c was the busiest one that I looked at.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-02 07:57:14 -07:00
Matthew Garrett
75fde2eddc [SERIAL] add PNP IDs for FPI based touchscreens
The Compaq TC1000 and Fujitsu Stylistic range of tablet machines use
touchscreens from FPI. These are implemented as serial interfaces,
generally exposed in the ACPIPNP information on the system. This patch
adds them to the 8250_pnp driver tables, avoiding the need to mess
around with setserial to set them up.

I haven't been able to confirm what FUJ02B5, FUJ02BA and FUJ02BB are.
FUJ02B1 refers to the controller for the system hotkeys. FUJ02BC appears
to be the last in the range - after this, they moved to Wacom-based
systems.

Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 21:27:15 +01:00
Dave Jones
e480af09c4 [SERIAL] tickle NMI watchdog on serial output.
Serial is _slow_ sometimes. So slow, that the NMI watchdog kicks in.

NMI Watchdog detected LOCKUP on CPU2CPU 2
Modules linked in: loop usb_storage md5 ipv6 parport_pc lp parport autofs4 i2c_dev i2c_core rfcomm l2cap bluetooth sunrpc pcdPid: 3138, comm: gpm Not tainted 2.6.11-1.1290_FC4smp
RIP: 0010:[<ffffffff80273b8a>] <ffffffff80273b8a>{serial_in+106}
RSP: 0018:ffff81003afc3d50  EFLAGS: 00000002
RAX: 0000000000000020 RBX: 0000000000000020 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff804dcd60
RBP: 00000000000024fc R08: 000000000000000a R09: 0000000000000033
R10: ffff81001beb7c20 R11: 0000000000000020 R12: ffffffff804dcd60
R13: ffffffff804ade76 R14: 000000000000002b R15: 000000000000002c
FS:  00002aaaaaac4920(0000) GS:ffffffff804fca00(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00002aaaaabcb000 CR3: 000000003c0d0000 CR4: 00000000000006e0
Process gpm (pid: 3138, threadinfo ffff81003afc2000, task ffff81003eb63780)
Stack: ffffffff80275f2e 0000000000000000 ffffffff80448380 0000000000007d6b
       000000000000002c fffffffffffffbbf 0000000000000292 0000000000008000
       ffffffff80138e8c 0000000000007d97
Call Trace:<ffffffff80275f2e>{serial8250_console_write+270} <ffffffff80138e8c>{__call_console_drivers+76}
       <ffffffff8013914b>{release_console_sem+315} <ffffffff80260325>{con_open+149}
       <ffffffff80254e99>{tty_open+537} <ffffffff80192713>{chrdev_open+387}
       <ffffffff80188824>{dentry_open+260} <ffffffff80188994>{filp_open+68}
       <ffffffff80187b73>{get_unused_fd+227} <ffffffff80188a6c>{sys_open+76}
       <ffffffff8010ebc6>{tracesys+209}

Code: 0f b6 c0 c3 66 90 41 57 49 89 f7 41 56 41 be 00 01 00 00 41
console shuts up ...

I initially did the patch below a year ago for the Fedora kernel, and have
been keeping it up to date since.  I recently got the same thing happening
on a vanilla kernel, so figured it was time to repost this.

Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 20:03:19 +01:00
Russell King
a6b93a9085 [SERIAL] Fix oops when removing suspended serial port
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row.  This causes
BUGs.  Avoid this by tracking the suspended state separately from
the initialised state.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:17:40 +01:00
Russell King
fe59d5372a [SERIAL] Fix resume handling bug
Unfortunately, pcmcia_dev_present() returns false when a device is
suspended, so checking this on resume does not work too well.  Omit
this test.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:14:07 +01:00
Alexey Dobriyan
1d5e799663 [SERIAL] CONFIG_PM=n slim: drivers/serial/8250_pci.c
Remove some code which is unneeded if CONFIG_PM=n.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:07:08 +01:00
Jonathan McDowell
255341c6fd [SERIAL] OMAP1510 serial fix for 115200 baud
The patch below is necessary for 115200 baud on an OMAP1510 internal UART.
It's been in the linux-omap tree for some time and with it applied to a
vanilla Linus git tree the serial console on the Amstrad Delta (which is
OMAP1510 based and whose initial bootloader runs at 115200) works fine (it
doesn't without it).

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:07:06 +01:00
Ram Gupta
80e3c2b659 [SERIAL] returning proper error from serial core driver
Fix the issue of returning 0 even in case of error from uart_set_info
function.  Now it returns the error EBUSY when it can not set new port.

Signed-off-by: Ram Gupta <r.gupta@astronautics.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:07:00 +01:00
Sergei Shtylyov
6c6a2334a1 [SERIAL] Make uart_line_info() correctly tell MMIO from I/O port
/proc/tty/driver/serial incorrectly claims that UARTs having iotype of
UPIO_MEM32, UPIO_AU, or UPIO_TSI are I/O mapped.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:57 +01:00
Sergei Shtylyov
a4b775735c [SERIAL] suspend/resume handlers don't have level arg anymore
8250.c and serial_txx9.c port suspend/resume handler still have this obsolete
argument documented...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:54 +01:00
Sergei Shtylyov
0b30d668a2 [SERIAL] 8250 resourse management fixes
I think register ranges obviously need to be claimed/released for all UARTs
including those with UPIO_MEM32 and UPIO_TSI iotype.

Also, serial8250_request_rsa_resources() returns false positives with
UPIO_MEM32, UPIO_AU, and UPIO_TSI iotype -- I don't think this makes any sense.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:49 +01:00
Russell King
f3d106881b [SERIAL] serial_cs: Add quirk for brainboxes 2-port RS232 card
Mauro Ziliani reports that this card has a higher clock rate.
Rather than tweak the 8250 driver to handle this, add a quirk to
pass the correct clock rate to the driver.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:45 +01:00
Russell King
20f130495c [SERIAL] serial_cs: handle Nokia multi->single port bodge via config quirk
According to the existing code, Nokia only make single-port cards,
but are detected as multi-port cards.  Handle this in roughly the
same way via the config quirk - forcing it to be a real single port
card (info->multi=0) changes the way we allocate the IO memory,
which might stop the card working.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:41 +01:00
Russell King
efd92dfaad [SERIAL] serial_cs: add configuration quirk
Add a quirk primerily to handle tweaks to the link->conf structure,
eg as required for Socket cards.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:37 +01:00
Russell King
7ef057fa70 [SERIAL] serial_cs: Convert Oxford 950 / Possio GCC wakeup quirk
Move the Oxford Semi OX950 / Possio GCC wakeup handling to a quirk
wakeup handler.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:34 +01:00
Russell King
eee3a883ce [SERIAL] serial_cs: convert IBM post-init handling to a quirk
Move IBM quirk handling into its own quirk entry.  Note that doing
quirk handling after we've registered the ports is racy, but since
I don't know if moving this will have an undesired effect, it's
probably better to leave where it is.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:30 +01:00
Russell King
a8244b564c [SERIAL] serial_cs: allow wildcarded quirks
Some quirks we will introduce next apply to (eg) all cards of one
manufacturer.  Therefore, we need a way to list these in the quirk
table - use ~0 - this is not a possible device ID value.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:27 +01:00
Russell King
1fbbac4bcb [SERIAL] serial_cs: convert multi-port table to quirk table
- rename multi_id table to serial_quirk / quirks[]
- use named initialisers
- store a pointer to the quirk table in the serial_info structure
  so we can use the quirk table entry later.
- apply multi-port quirk after the multi-port guessing code,
  but only if it's != -1.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:23 +01:00
Russell King
43549ad7a7 [SERIAL] serial_cs: Use clean up multiport card detection
- Use ARRAY_SIZE() instead of home grown based version.
- use parse->manfid.card rather than le16_to_cpu(buf[1]) -
  manfid.card is already converted to this format.
- use info->prodid in subsequent tests rather than
  parse->manfid.card.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:20 +01:00
Russell King
de6cc84f72 [SERIAL] Remove m32r_sio dependency on asm/serial.h
m32r_sio re-uses a custom defined BASE_BAUD from asm/serial.h,
and replaces SERIAL_PORT_DFNS with its own driver private copy.
Since asm/serial.h is supposed to define 8250-based ports using
these symbols, this isn't a sane idea.

Hence, eliminate asm/serial.h from m32r_sio.c.

Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:03 +01:00
Amol Lad
65da4d81f4 [PATCH] ioremap balanced with iounmap for drivers/serial/sunsu.c
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David S. Miller <davem@sunset.davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:32 -07:00
Amol Lad
af907dc8cd [PATCH] ioremap balanced with iounmap for drivers/serial/mux.c
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:32 -07:00
Amol Lad
a141a04330 [PATCH] ioremap balanced with iounmap for drivers/serial/mpsc.c
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:32 -07:00
Amol Lad
be618f550c [PATCH] ioremap balanced with iounmap for drivers/serial/mpc52xx_uart.c
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:32 -07:00
Amol Lad
6257b3bdfd [PATCH] ioremap balanced with iounmap for drivers/serial/ip22zilog.c
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:32 -07:00
Amol Lad
f466413261 [PATCH] ioremap balanced with iounmap for drivers/serial/ioc4_serial.c
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:32 -07:00
Amol Lad
d9964d5c90 [PATCH] ioremap balanced with iounmap for drivers/serial/8250_gsc.c
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:32 -07:00
Amol Lad
f12ad7d59a [PATCH] ioremap balanced with iounmap for drivers/serial/8250_acorn,c
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.

Signed-off-by: Amol Lad <amol@verismonetworks.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-01 00:39:32 -07:00
David S. Miller
fbe96f92b3 [SERIAL] sunzilog: Mark sunzilog_init_hw as __devinit.
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-09-29 16:12:43 -07:00
Peter Korsgaard
b22b4cdd53 [PATCH] fix serial/amba-pl011.c console Kconfig
Fix the Kconfig entry for console on AMBA PL011 to match the code.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-29 09:18:14 -07:00
Linus Torvalds
ebdea46fec Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (130 commits)
  [ARM] 3856/1: Add clocksource for Intel IXP4xx platforms
  [ARM] 3855/1: Add generic time support
  [ARM] 3873/1: S3C24XX: Add irq_chip names
  [ARM] 3872/1: S3C24XX: Apply consistant tabbing to irq_chips
  [ARM] 3871/1: S3C24XX: Fix ordering of EINT4..23
  [ARM] nommu: confirms the CR_V bit in nommu mode
  [ARM] nommu: abort handler fixup for !CPU_CP15_MMU cores.
  [ARM] 3870/1: AT91: Start removing static memory mappings
  [ARM] 3869/1: AT91: NAND support for DK and KB9202 boards
  [ARM] 3868/1: AT91 hardware header update
  [ARM] 3867/1: AT91 GPIO update
  [ARM] 3866/1: AT91 clock update
  [ARM] 3865/1: AT91RM9200 header updates
  [ARM] 3862/2: S3C2410 - add basic power management support for AML M5900 series
  [ARM] kthread: switch arch/arm/kernel/apm.c
  [ARM] Off-by-one in arch/arm/common/icst*
  [ARM] 3864/1: Refactore sharpsl_pm
  [ARM] 3863/1: Add Locomo SPI Device
  [ARM] 3847/2:  Convert LOMOMO to use struct device for GPIOs
  [ARM] Use CPU_CACHE_* where possible in asm/cacheflush.h
  ...
2006-09-28 14:40:39 -07:00