Commit Graph

936 Commits

Author SHA1 Message Date
Chin-Ran Lo
8cf60cf238 Bluetooth: btmrvl: don't send data to firmware while processing suspend
Usually when driver sends data to firmware it receives TX_DONE
(DN_LD_HOST_INT_STATUS) interrupt from firmware right away.
It's also observed that some times the fireware could delay
sending DN_LD_HOST_INT_STATUS interrupt. If driver sends data to
firmware during suspend processing and the TX_DONE interrupt is
delayed, it may come back at wrong time when SDIO host driver is
in the middle of suspending.

Block any data from stack while suspending. Also skip sending
data that are already in driver tx_queue.

Don't purge the skb queue on suspend to avoid intermittent music
after system resumes from S3.

Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-06 16:37:14 +01:00
Chin-Ran Lo
d716892f08 Bluetooth: btmrvl: max out host sleep parameter 'gap'
For gpio=0xff (wake up host through SDIO interface) case,
gap=0xff means no delay (same as gap=0) for incoming data packet
to be sent to host after host sleep is activated.
Change it to the maximum delay to reduce the chance that RX
interrupt could be delivered while host controller suspends.

Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-06 16:37:14 +01:00
Chin-Ran Lo
86f7ac77d4 Bluetooth: btmrvl: fix hung task warning dump
It's been observed that when bluetooth driver fails to
activate the firmware, below hung task warning dump is
displayed after 120 seconds.

[   36.461022] Bluetooth: vendor=0x2df, device=0x912e, class=255, fn=2
[   56.512128] Bluetooth: FW failed to be active in time!
[   56.517264] Bluetooth: Downloading firmware failed!
[  240.252176] INFO: task kworker/3:2:129 blocked for more than 120 seconds.
[  240.258931]       Not tainted 3.18.0 #254
[  240.262972] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  240.270751] kworker/3:2     D ffffffc000205760     0   129      2 0x00000000
[  240.277825] Workqueue: events request_firmware_work_func
[  240.283134] Call trace:
[  240.285581] [<ffffffc000205760>] __switch_to+0x80/0x8c
[  240.290693] [<ffffffc00088dae0>] __schedule+0x540/0x7b8
[  240.295921] [<ffffffc00088ddd0>] schedule+0x78/0x84
[  240.300764] [<ffffffc0006dfd48>] __mmc_claim_host+0xe8/0x1c8
[  240.306395] [<ffffffc0006edd6c>] sdio_claim_host+0x74/0x84
[  240.311840] [<ffffffbffc163d08>] 0xffffffbffc163d08
[  240.316685] [<ffffffbffc165104>] 0xffffffbffc165104
[  240.321524] [<ffffffbffc130cf8>] mwifiex_dnld_fw+0x98/0x110 [mwifiex]
[  240.327918] [<ffffffbffc12ee88>] mwifiex_remove_card+0x2c4/0x5fc [mwifiex]
[  240.334741] [<ffffffc000596780>] request_firmware_work_func+0x44/0x80
[  240.341127] [<ffffffc00023b934>] process_one_work+0x2ec/0x50c
[  240.346831] [<ffffffc00023c6a0>] worker_thread+0x350/0x470
[  240.352272] [<ffffffc0002419bc>] kthread+0xf0/0xfc
[  240.357019] 2 locks held by kworker/3:2/129:
[  240.361248]  #0:  ("events"){.+.+.+}, at: [<ffffffc00023b840>] process_one_work+0x1f8/0x50c
[  240.369562]  #1:  ((&fw_work->work)){+.+.+.}, at: [<ffffffc00023b840>] process_one_work+0x1f8/0x50c
[  240.378589]   task                        PC stack   pid father
[  240.384501] kworker/1:1     D ffffffc000205760     0    40      2 0x00000000
[  240.391524] Workqueue: events mtk_atomic_work
[  240.395884] Call trace:
[  240.398317] [<ffffffc000205760>] __switch_to+0x80/0x8c
[  240.403448] [<ffffffc00027279c>] lock_acquire+0x128/0x164
[  240.408821] kworker/3:2     D ffffffc000205760     0   129      2 0x00000000
[  240.415867] Workqueue: events request_firmware_work_func
[  240.421138] Call trace:
[  240.423589] [<ffffffc000205760>] __switch_to+0x80/0x8c
[  240.428688] [<ffffffc00088dae0>] __schedule+0x540/0x7b8
[  240.433886] [<ffffffc00088ddd0>] schedule+0x78/0x84
[  240.438732] [<ffffffc0006dfd48>] __mmc_claim_host+0xe8/0x1c8
[  240.444361] [<ffffffc0006edd6c>] sdio_claim_host+0x74/0x84
[  240.449801] [<ffffffbffc163d08>] 0xffffffbffc163d08
[  240.454649] [<ffffffbffc165104>] 0xffffffbffc165104
[  240.459486] [<ffffffbffc130cf8>] mwifiex_dnld_fw+0x98/0x110 [mwifiex]
[  240.465882] [<ffffffbffc12ee88>] mwifiex_remove_card+0x2c4/0x5fc [mwifiex]
[  240.472705] [<ffffffc000596780>] request_firmware_work_func+0x44/0x80
[  240.479090] [<ffffffc00023b934>] process_one_work+0x2ec/0x50c
[  240.484794] [<ffffffc00023c6a0>] worker_thread+0x350/0x470
[  240.490231] [<ffffffc0002419bc>] kthread+0xf0/0xfc

This patch adds missing sdio_release_host() call so that wlan driver
thread can claim sdio host.

Fixes: 4863e4cc31 ("Bluetooth: btmrvl: release sdio bus after firmware is up")
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-04 19:25:56 +01:00
Heikki Krogerus
adbdeae5ce Bluetooth: hci_bcm: new ACPI IDs
These are used at least by Acer with BCM43241.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-04 19:22:57 +01:00
Heikki Krogerus
d3d2072540 Bluetooth: hci_bcm: move all Broadcom ACPI IDs to BCM HCI driver
The IDs should all be for Broadcom BCM43241 module, and
hci_bcm is now the proper driver for them. This removes one
of two different ways of handling PM with the module.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-01-04 19:22:05 +01:00
Syam Sidhardhan
7ddb69222d Bluetooth: bfusb: Fix the return error code
-ENOMEM is the appropriate error code instead of -EIO.

Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-22 15:25:33 +01:00
Syam Sidhardhan
f71e823b87 Bluetooth: bfusb: Remove redundant error message
devm_kzalloc prints its own OOM message upon failure.

Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-22 15:25:33 +01:00
Syam Sidhardhan
17722e245b Bluetooth: bcm203x: Remove redundant error message
devm_kzalloc prints its own OOM message upon failure.

Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-22 15:25:33 +01:00
Luka Karinja
806f50c729 Bluetooth: hci_bcm: Add BCM2E65 ACPI ID
Add BCM2E65 device in acpi_device_id table used on Asus T100TAF.

Signed-off-by: Luka Karinja <luka.karinja@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-20 14:15:25 +01:00
Andrei Emeltchenko
87a6b9bd63 Bluetooth: h5: Do not initialize Configuration field
Initializing Configuration field in H5 Config message to 0x01 gives
wrong impression that the value is used and needed. Later on the whole
field is rewritten with h5_cfg_field().

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 19:19:17 +01:00
Loic Poulain
6c483de1b3 Bluetooth: btintel: Create common Intel Version Read function
The Intel Version Read command is used to retrieve information
about hardware and firmware version/revision of Intel Bluetooth
controllers. This is an Intel generic command used in USB and
UART drivers.

Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 00:51:51 +01:00
Loic Poulain
28dc4b92e2 Bluetooth: btintel: Add manufacturing enter/exit helpers
Older Intel controllers need to enter manufacturing mode to perform
some vendor specific operations (patching, configuration...).
Add enter/exit manufaturing methods and refactor existing
manufacturing code.
Exit can be configured to perform a reset. Reset can be performed
either with patches activated or deactivated.

Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 00:51:50 +01:00
Dmitry Tunin
1623d0bf84 Bluetooth: Add support of Toshiba Broadcom based devices
BugLink: https://bugs.launchpad.net/bugs/1522949

    T: Bus=03 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
    D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
    P: Vendor=0930 ProdID=0225 Rev=01.12
    S: Manufacturer=Broadcom Corp
    S: Product=BCM43142A0
    S: SerialNumber=4CBB58034671
    C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
    I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
    I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
    I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
    I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2015-12-10 00:51:50 +01:00
Loic Poulain
a0c3824515 Bluetooth: hci_intel: Use shorter timeout for HCI commands
Use the standard HCI_CMD_TIMEOUT(1s) for HCI command instead of
HCI_INIT_TIMEOUT(10s) which is not justified in these cases.

Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 00:51:50 +01:00
Peter Hurley
e6e981c742 Bluetooth: hci_ldisc: Remove dead code
The N_HCI ldisc does not define a flush_buffer() ldisc method, so
the check when opening the ldisc is always false.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 00:51:50 +01:00
Andrei Emeltchenko
742c595168 Bluetooth: Simplify setting Configuration Field
Only Sliding Window Size is used at the moment for H5 Bluetooth
Configuration messages.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 00:51:49 +01:00
Andrei Emeltchenko
1d3a1e69ad Bluetooth: Use hexadecimal notation for mask
Using hexadecimal notation for mask makes code easier to read

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-12-10 00:51:49 +01:00
Andrei Emeltchenko
e9d6376725 Bluetooth: Use hex notation for mask
This makes it easier to read and makes code consistent.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-11-19 17:50:33 +01:00
Andrei Emeltchenko
4223f368b9 Bluetooth: Fix mask for H5 header len
Fixes mask when calculating three-wire (h5) length.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-11-19 17:50:33 +01:00
Marcel Holtmann
618e8bc228 Bluetooth: Use new hci_skb_pkt_* wrappers for drivers
The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-11-19 17:50:27 +01:00
Linus Torvalds
2df4ee78d0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet.

 2) Several spots need to get to the original listner for SYN-ACK
    packets, most spots got this ok but some were not.  Whilst covering
    the remaining cases, create a helper to do this.  From Eric Dumazet.

 3) Missiing check of return value from alloc_netdev() in CAIF SPI code,
    from Rasmus Villemoes.

 4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich.

 5) Use after free in mvneta driver, from Justin Maggard.

 6) Fix race on dst->flags access in dst_release(), from Eric Dumazet.

 7) Add missing ZLIB_INFLATE dependency for new qed driver.  From Arnd
    Bergmann.

 8) Fix multicast getsockopt deadlock, from WANG Cong.

 9) Fix deadlock in btusb, from Kuba Pawlak.

10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6
    counter state.  From Sabrina Dubroca.

11) Fix packet_bind() race, which can cause lost notifications, from
    Francesco Ruggeri.

12) Fix MAC restoration in qlcnic driver during bonding mode changes,
    from Jarod Wilson.

13) Revert bridging forward delay change which broke libvirt and other
    userspace things, from Vlad Yasevich.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
  Revert "bridge: Allow forward delay to be cfgd when STP enabled"
  bpf_trace: Make dependent on PERF_EVENTS
  qed: select ZLIB_INFLATE
  net: fix a race in dst_release()
  net: mvneta: Fix memory use after free.
  net: Documentation: Fix default value tcp_limit_output_bytes
  macvtap: Resolve possible __might_sleep warning in macvtap_do_read()
  mvneta: add FIXED_PHY dependency
  net: caif: check return value of alloc_netdev
  net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA
  drivers: net: xgene: fix RGMII 10/100Mb mode
  netfilter: nft_meta: use skb_to_full_sk() helper
  net_sched: em_meta: use skb_to_full_sk() helper
  sched: cls_flow: use skb_to_full_sk() helper
  netfilter: xt_owner: use skb_to_full_sk() helper
  smack: use skb_to_full_sk() helper
  net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid()
  bpf: doc: correct arch list for supported eBPF JIT
  dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put"
  bonding: fix panic on non-ARPHRD_ETHER enslave failure
  ...
2015-11-10 18:11:41 -08:00
Linus Torvalds
e880e87488 driver core update for 4.4-rc1
Here's the "big" driver core updates for 4.4-rc1.  Primarily a bunch of
 debugfs updates, with a smattering of minor driver core fixes and
 updates as well.
 
 All have been in linux-next for a long time.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
 Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
 =g7ZO
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg KH:
 "Here's the "big" driver core updates for 4.4-rc1.  Primarily a bunch
  of debugfs updates, with a smattering of minor driver core fixes and
  updates as well.

  All have been in linux-next for a long time"

* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  debugfs: Add debugfs_create_ulong()
  of: to support binding numa node to specified device in devicetree
  debugfs: Add read-only/write-only bool file ops
  debugfs: Add read-only/write-only size_t file ops
  debugfs: Add read-only/write-only x64 file ops
  debugfs: Consolidate file mode checks in debugfs_create_*()
  Revert "mm: Check if section present during memory block (un)registering"
  driver-core: platform: Provide helpers for multi-driver modules
  mm: Check if section present during memory block (un)registering
  devres: fix a for loop bounds check
  CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
  base/platform: assert that dev_pm_domain callbacks are called unconditionally
  sysfs: correctly handle short reads on PREALLOC attrs.
  base: soc: siplify ida usage
  kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
  kobject: explain what kobject's sd field is
  debugfs: document that debugfs_remove*() accepts NULL and error values
  debugfs: Pass bool pointer to debugfs_create_bool()
  ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
2015-11-04 21:50:37 -08:00
Kuba Pawlak
f6fc86f2c5 Bluetooth: Fix possible deadlock in btusb
commit 8f9d02f470 introduced spinlocks
in btusb_work. This is run in a context of a worqueue and can be interrupted
by hardware irq. If it happens while spinlock is held, we have a deadlock.
Solution is to use _irqsave/_resore version of locking

[  466.460560] =================================
[  466.460565] [ INFO: inconsistent lock state ]
[  466.460572] 4.3.0-rc6+ #1 Tainted: G        W
[  466.460576] ---------------------------------
[  466.460582] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[  466.460589] kworker/0:2/94 [HC0[0]:SC0[0]:HE1:SE1] takes:
[  466.460595]  (&(&data->rxlock)->rlock){?.-...}, at: [<ffffffffa0526923>] btusb_work+0xa3/0x3fd [btusb]
[  466.460621] {IN-HARDIRQ-W} state was registered at:
[  466.460625]   [<ffffffff811021b5>] __lock_acquire+0xc45/0x1e80
[  466.460638]   [<ffffffff811040d5>] lock_acquire+0xe5/0x1f0
[  466.460646]   [<ffffffff8182f108>] _raw_spin_lock+0x38/0x50
[  466.460657]   [<ffffffffa0525448>] btusb_recv_intr+0x38/0x170 [btusb]
[  466.460668]   [<ffffffffa0525626>] btusb_intr_complete+0xa6/0x130 [btusb]
[  466.460679]   [<ffffffff815d8f1e>] __usb_hcd_giveback_urb+0x8e/0x160
[  466.460690]   [<ffffffff815d911f>] usb_hcd_giveback_urb+0x3f/0x120
[  466.460698]   [<ffffffff81606e4d>] uhci_giveback_urb+0xad/0x280
[  466.460706]   [<ffffffff81608f64>] uhci_scan_schedule.part.33+0x6b4/0xbe0
[  466.460714]   [<ffffffff81609b50>] uhci_irq+0xd0/0x180
[  466.460722]   [<ffffffff815d8296>] usb_hcd_irq+0x26/0x40
[  466.460729]   [<ffffffff81117d40>] handle_irq_event_percpu+0x40/0x300
[  466.460739]   [<ffffffff81118040>] handle_irq_event+0x40/0x60
[  466.460746]   [<ffffffff8111af39>] handle_fasteoi_irq+0x89/0x150
[  466.460754]   [<ffffffff8101e0f3>] handle_irq+0x73/0x120
[  466.460763]   [<ffffffff81832f11>] do_IRQ+0x61/0x120
[  466.460772]   [<ffffffff8183084c>] ret_from_intr+0x0/0x31
[  466.460780]   [<ffffffff81697a77>] cpuidle_enter+0x17/0x20
[  466.460790]   [<ffffffff810f62c2>] call_cpuidle+0x32/0x60
[  466.460800]   [<ffffffff810f65a8>] cpu_startup_entry+0x2b8/0x3f0
[  466.460807]   [<ffffffff818214ca>] rest_init+0x13a/0x140
[  466.460817]   [<ffffffff81f76029>] start_kernel+0x4a3/0x4c4
[  466.460827]   [<ffffffff81f75339>] x86_64_start_reservations+0x2a/0x2c
[  466.460837]   [<ffffffff81f75485>] x86_64_start_kernel+0x14a/0x16d
[  466.460846] irq event stamp: 754913
[  466.460851] hardirqs last  enabled at (754913): [<ffffffff8182f4cc>] _raw_spin_unlock_irq+0x2c/0x40
[  466.460861] hardirqs last disabled at (754912): [<ffffffff8182f28d>] _raw_spin_lock_irq+0x1d/0x60
[  466.460869] softirqs last  enabled at (753024): [<ffffffff810aeaa0>] __do_softirq+0x380/0x490
[  466.460880] softirqs last disabled at (753009): [<ffffffff810aedef>] irq_exit+0x10f/0x120
[  466.460888]
               other info that might help us debug this:
[  466.460894]  Possible unsafe locking scenario:

[  466.460899]        CPU0
[  466.460903]        ----
[  466.460907]   lock(&(&data->rxlock)->rlock);
[  466.460915]   <Interrupt>
[  466.460918]     lock(&(&data->rxlock)->rlock);
[  466.460926]
                *** DEADLOCK ***

[  466.460935] 2 locks held by kworker/0:2/94:
[  466.460939]  #0:  ("events"){.+.+.+}, at: [<ffffffff810c69bb>] process_one_work+0x16b/0x660
[  466.460958]  #1:  ((&data->work)){+.+...}, at: [<ffffffff810c69bb>] process_one_work+0x16b/0x660
[  466.460974]

Signed-off-by: Kuba Pawlak <kubax.t.pawlak@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-11-05 04:03:11 +01:00
Julia Lawall
c0859e2f4c Bluetooth: btmrvl: add missing of_node_put
for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression e;
local idexpression n;
@@

 for_each_compatible_node(n, ...) {
   ... when != of_node_put(n)
       when != e = n
(
   return n;
|
+  of_node_put(n);
?  return ...;
)
   ...
 }
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-25 21:03:29 +01:00
Dan Carpenter
a1857390e2 Bluetooth: hci_bcm: checking for ERR_PTR instead of NULL
bt_skb_alloc() returns NULL on error, it never returns an ERR_PTR.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-22 11:32:47 +02:00
Marcel Holtmann
213445b2b4 Bluetooth: btintel: Enable extra Intel vendor events
The Intel Bluetooth controllers can emit extra vendor specific events in
error conditions or for debugging purposes. To make the life easier for
engineers, enable them by default. When the vendor_diag options has been
enabled, then additional debug events are also enabled.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 07:34:11 +03:00
Marcel Holtmann
e4c534bbac Bluetooth: btusb: Set manufacturer for Intel bootloader devices
For Intel bootloader devices, set the manufacturer information so that
it becomes possible to decode the boot process.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 07:32:12 +03:00
Marcel Holtmann
aee61f7aa8 Bluetooth: hci_uart: Provide initial manufacturer information
Provide an early indication about the manufacturer information so that
it can be forwarded into monitor channel.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 07:20:44 +03:00
Marcel Holtmann
22f8e9dbf6 Bluetooth: btusb: Add support for latest Apple controllers
The latest Apple Bluetooth controllers with Broadcom chip in it have
a small design change. Instead of including a USB hub with mouse and
keyboard devices, they are now HID interfaces on the same device.

T:  Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 39 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=8290 Rev= 0.79
S:  Manufacturer=Broadcom Corp.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=  0mA
A:  FirstIf#= 2 IfCount= 4 Cls=ff(vend.) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=01 Driver=usbhid
E:  Ad=85(I) Atr=03(Int.) MxPS=   8 Ivl=10ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=usbhid
E:  Ad=86(I) Atr=03(Int.) MxPS=   8 Ivl=10ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 3 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 3 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 3 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 3 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 3 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

The general layout of Bluetooth devices is that interface 0 is the main
interface and interface 1 is for audio data. This design obviously moves
it to main interface 2 and audio data on interface 3.

Starting with the MacBookPro12,1 (early 2015 models) the new Broadcom
BCM943602CS cards are used which show this interface layout.

usb 4-1.5: New USB device found, idVendor=05ac, idProduct=8290
usb 4-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-1.5: Product: Bluetooth USB Host Controller
usb 4-1.5: Manufacturer: Broadcom Corp.
Bluetooth: hci0: BCM: chip id 102 build 0243
Bluetooth: hci0: BCM: product 05ac:8290
Bluetooth: hci0: BCM20703A1 Generic USB UHE Apple 20Mhz fcbga_X87

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:24 +02:00
Marcel Holtmann
49a5f782d0 Bluetooth: btusb: Set early vendor info for Intel and Broadcom
For the controllers from Intel and Broadcom (including Apple), it is
helpful to have the information about the manufacturer send out early.

This patch sets the hdev->manufacturer information which will be send
out before actually calling the vendor specific hdev->setup driver
callback.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:23 +02:00
Dmitry Tunin
18e0afab8c Bluetooth: ath3k: Add support of AR3012 0cf3:817b device
T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817b Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1506615

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2015-10-21 00:49:23 +02:00
Dmitry Tunin
cd355ff071 Bluetooth: ath3k: Add new AR3012 0930:021c id
This adapter works with the existing linux-firmware.

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=021c Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1502781

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2015-10-21 00:49:23 +02:00
Santtu Rekilä
2faf71ce90 Bluetooth: btusb: Add support for Foxconn/Lenovo BCM43142A0 (105b:e065)
Recently salvaged this 'BCM43142A0' WiFi/Bluetooth module from a Lenovo laptop
and noticed it doesn't work automatically, because the USB IDs are missing
from btusb.c.

Plugging in the adapter on Linux 4.1 (dmesg):
usb 3-3.3.3: new full-speed USB device number 90 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E

/sys/kernel/debug/usb/devices:
T:  Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 90 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=105b ProdID=e065 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM43142A0
S:  SerialNumber=0090A286559E
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Support for the chipset was added in commit 88f9b65 and a similar BCM43142
based device was added in commit 8f0c304.

To work around the issue, I got the firmware
(BCM43142A0_001.001.011.0122.0153) off a Windows installation of Broadcom
bluetooth driver and converted it to a .hcd -file via. hex2hcd and placed it
in /lib/firmware/brcm/BCM.hcd. After that:

$ echo "105b e065 0 19ff 0239" > /sys/bus/usb/drivers/btusb/new_id
...(plug in the adapter)
usb 3-3.3.3: new full-speed USB device number 91 using xhci_hcd
usb 3-3.3.3: New USB device found, idVendor=105b, idProduct=e065
usb 3-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3.3.3: Product: BCM43142A0
usb 3-3.3.3: Manufacturer: Broadcom Corp
usb 3-3.3.3: SerialNumber: 0090A286559E
Bluetooth: hci0: BCM: chip id 70
Bluetooth: hci0: BCM (001.001.011) build 0000
bluetooth hci0: firmware: direct-loading firmware brcm/BCM.hcd
Bluetooth: hci0: BCM (001.001.011) build 0154

Bam, now it works for me!

/sys/kernel/debug/usb/devices:
T:  Bus=03 Lev=03 Prnt=22 Port=02 Cnt=02 Dev#= 92 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=105b ProdID=e065 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM43142A0
S:  SerialNumber=0090A286559E
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Santtu Rekilä <sare@r00t3d.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21 00:49:23 +02:00
Marcel Holtmann
34cea41e84 Bluetooth: btbcm: Read USB product information for Apple devices
For the Apple Bluetooth devices, read the USB product information and
print them. This allows for easy mapping of chip and USB details.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:23 +02:00
Marcel Holtmann
8045ce2197 Bluetooth: btbcm: Fix firmware version number calculation
The calculation for the firmware version number is off by one bit.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:22 +02:00
Marcel Holtmann
6c9d435d35 Bluetooth: btusb: Mark BCM2045 devices to have broken link key commands
The BCM2045 seems to have a problem with the stored link key commands
and thus just mark them as broken.

  HCI Event: Command Complete (0x0e) plen 12
     Read Local Supported Features (0x04|0x0003) ncmd 1
     status 0x00
     Features: 0xff 0xff 0x8d 0xfe 0x8f 0xf9 0x00 0x80
  HCI Event: Command Complete (0x0e) plen 12
     Read Local Version Information (0x04|0x0001) ncmd 1
     status 0x00
     HCI Version: 2.0 (0x3) HCI Revision: 0x2000
     LMP Version: 2.0 (0x3) LMP Subversion: 0x410d
     Manufacturer: Broadcom Corporation (15)
  HCI Event: Command Complete (0x0e) plen 11
     Read Buffer Size (0x04|0x0005) ncmd 1
     status 0x00
     ACL MTU 1017:8 SCO MTU 64:0
  HCI Event: Command Complete (0x0e) plen 68
     Read Local Supported Commands (0x04|0x0002) ncmd 1
     status 0x00
     Commands: ffffff03feffcfffffffffff0300f8ff07
  HCI Event: Command Complete (0x0e) plen 4
     Delete Stored Link Key (0x03|0x0012) ncmd 1
     status 0x11 deleted 2048
     Error: Unsupported Feature or Parameter Value

From the looks of it, this device seems genuine and not one of the
devices that are neither Broadcom nor CSR devices in reality.

T: Bus=04 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=2045 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM2045A
S: SerialNumber=000000000000
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)

Reported-and-tested-by: Julio González Mejías <juliolokooo@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:22 +02:00
Marcel Holtmann
3e24767b78 Bluetooth: btintel: Add diagnostic support for older controllers
For the older controllers like Wilkens Peak and Stone Peak, enabling the
traces requires to switch into manufacturer mode first. This patch does
exactly that, but only for these older controllers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:22 +02:00
Marcel Holtmann
d8270fbb3f Bluetooth: btintel: Set quirk for non-persistent diagnostic settings
For Intel controllers the diagnostics settings are not persistent over
HCI Reset. So set the quirk to programm them again on every power up.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:22 +02:00
Arnd Bergmann
7841d06e43 Bluetooth: bpa10x: fix BT_HCIUART dependency
The change to bpa10x to use the h4_recv_buf helper added a dependency
on BT_HCIUART. This was incorrectly added to Kconfig by adding a
'select' statement, which now in turn causes build failures
when CONFIG_TTY is not set:

warning: (BT_HCIBPA10X) selects BT_HCIUART which has unmet direct dependencies (NET && BT && TTY)
vers/built-in.o: In function `hci_uart_tty_receive':
fpga-mgr.c:(.text+0x282824): undefined reference to `tty_unthrottle'
drivers/built-in.o: In function `hci_uart_tty_ioctl':
fpga-mgr.c:(.text+0x282aa0): undefined reference to `n_tty_ioctl_helper'
drivers/built-in.o: In function `hci_uart_flush':

This replaces the 'select BT_HCIUART' dependency with 'depends on', which
does not have this kind of problem. Alternatively, one could add 'depends
on TTY', but avoiding 'select' on user-visible options is generally the
preferred choice as that does not introduce the potential for dependency
loops or incomplete dependency chains.

Fixes: 9148991924 ("Bluetooth: bpa10x: Fix missing BT_HCIUART dependency")
Fixes: 943cc59219 ("Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-10-21 00:49:22 +02:00
Marcel Holtmann
2220994e71 Bluetooth: btusb: Print information of Intel SfP lock states
The lock states from Intel SfP controllers can only be read once before
loading the firmware. So for debugging purposes, print them out.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:22 +02:00
Marcel Holtmann
6d2e50d240 Bluetooth: btintel: Add support for enabling tracing functionality
For Intel controllers with firmware that allows tracing of baseband
functionality this allows enabling it via set_diag driver callback.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:21 +02:00
Marcel Holtmann
9d08f50401 Bluetooth: btusb: Add support for Broadcom LM_DIAG interface
The Broadcom Bluetooth USB devices have a third interface that is
dedicated for LM_DIAG messages. The If#= 2 describes this interface
and it consists of one bulk in and one bulk endpoint.

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 38 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=19ff ProdID=0239 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

For all Broadcom based devices with this interface, the driver now
claims it and schedules URBs for it. This allows to capture the
LM_DIAG messages and allows forwarding them via hci_recv_diag into
the diagnostic channel of the Bluetooth subsystem.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:49:21 +02:00
Marcel Holtmann
9148991924 Bluetooth: bpa10x: Fix missing BT_HCIUART dependency
Selecting just BT_HCIUART_H4 is not enough and it also needs to select
BT_HCIUART to avoid this warning:

warning: (BT_HCIBPA10X) selects BT_HCIUART_H4 which has unmet direct
dependencies (NET && BT && BT_HCIUART)

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 00:48:13 +02:00
Marcel Holtmann
943cc59219 Bluetooth: bpa10x: Use h4_recv_buf helper for frame reassembly
The manually coded frame reassembly is actually broken. The h4_recv_buf
helper from the UART driver is a perfect fit for frame reassembly for
this driver. So just export that function and use it here as well.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08 10:04:27 +03:00
Marcel Holtmann
881f7e86a1 Bluetooth: bpa10x: Add support for set_diag driver callback
The BPA-10x devices support tracing operation. Use the set_diag driver
callback to allow enabling and disabling that functionality.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08 10:03:02 +03:00
Marcel Holtmann
ddd68ec8f4 Bluetooth: bpa10x: Read revision information in setup stage
For debugging pruposes, read the revision string of the BPA-10x devices
and print it. For example one of the latest devices respond with the
string SNIF_102,BB930,02/01/18,10:37:56.

  < HCI Command: Vendor (0x3f|0x000e) plen 1
          07                                               .
  > HCI Event: Command Complete (0x0e) plen 49
        Vendor (0x3f|0x000e) ncmd 1
          Status: Success (0x00)
          53 4e 49 46 5f 31 30 32 2c 42 42 39 33 30 2c 30  SNIF_102,BB930,0
          32 2f 30 31 2f 31 38 2c 31 30 3a 33 37 3a 35 36  2/01/18,10:37:56
          00 00 00 00 00 00 00 00 00 00 00 00 00           .............

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08 10:01:25 +03:00
Marcel Holtmann
075e1f5e6c Bluetooth: hci_bcm: Enable support for set_diag driver callback
The set_diag driver callback allows enabling and disabling the vendor
specific diagnostic information. Since Broadcom chips have support for
a dedicated LM_DIAG channel, hook it up accordingly.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08 09:59:16 +03:00
Marcel Holtmann
94c58132c0 Bluetooth: hci_bcm: Enable parsing of LM_DIAG messages
The Broadcom UART based controllers can send LM_DIAG messages with the
identifier 0x07 inside the HCI stream. These messages are 63 octets in
size and have no variable payload or length indicator.

This patch adds correct parsing information for the h4_recv_buf handler
and in case these packets are received, they are forwarded to the
Bluetooth core via hci_recv_diag interface.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-08 09:53:16 +03:00
Marcel Holtmann
9bc63ca090 Bluetooth: btbcm: Read the local name in setup stage
The Broadcom Bluetooth controllers have the chip name included in the
ROM firmware or later in the patchram firmware. For debugging purposes
read the local name and print it out. This is only done during setup
stage and only once before loading the firmware and once after loading
the firmware.

For the Broadcom based controllers from Apple, the name is only read once
after determining the chip id.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-07 07:41:11 +03:00
Marcel Holtmann
e9ca8bf157 Bluetooth: Move handling of HCI_RUNNING flag into core
Setting and clearing of HCI_RUNNING flag in each and every driver is
just duplicating the same code all over the place. So instead of having
the driver do it in their hdev->open and hdev->close callbacks, set it
globally in the core transport handling.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-05 10:30:25 +03:00