It seems git has been getting confused by the very similar contexts
for the speaker DAIs and has been applying patches to the wrong places
causing all sorts of confusion. Fix this up by hand.
Reported-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel writes:
Just a few small things to fix regressions, somehow all patches from Jani:
- Fix dpms confusion about which platforms support intermediate modes on
vga.
- Revert the "ignore vbt for eDP bpc" patch, it breaks machines. This will
annoy mbp retina owners again, but windows machines seem to _really_
depend upon this. We can try to quirk the mbp retinas again in 3.8 and
backport the patch.
- Fix connector leaks when the sdvo setup failed, resulted in an OOPS
later on when trying to probe that connector (with it's encoder kfree'd
already).
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: do not ignore eDP bpc settings from vbt
drm/i915/sdvo: clean up connectors on intel_sdvo_init() failures
drm/i915/crt: fix DPMS standby and suspend mode handling
It is unnecessary to disable preemption explicitly while calling
copy_highpage(). Because copy_highpage() will do it again through
kmap_atomic/kunmap_atomic.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The TTM page can be allocated from high memory. In such case it is
wrong to use the page_address(page) as the virtual address for the high memory
page.
bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50241
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
copy_to_user() returns the number of bytes remaining to be copied, but
we want to return a negative error code here. I fixed a couple of these
last year, but I missed this one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check (ha->addr == dev->dev_addr) is always true because dev_addr_init()
sets this. Correct the check to behave properly on addr removal.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if a socket was repaired with a few packet in a write queue,
a kernel bug may be triggered:
kernel BUG at net/ipv4/tcp_output.c:2330!
RIP: 0010:[<ffffffff8155784f>] tcp_retransmit_skb+0x5ff/0x610
According to the initial realization v3.4-rc2-963-gc0e88ff,
all skb-s should look like already posted. This patch fixes code
according with this sentence.
Here are three points, which were not done in the initial patch:
1. A tcp send head should not be changed
2. Initialize TSO state of a skb
3. Reset the retransmission time
This patch moves logic from tcp_sendmsg to tcp_write_xmit. A packet
passes the ussual way, but isn't sent to network. This patch solves
all described problems and handles tcp_sendpages.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users of GCC 4.7 have reported compiler errors due to having inline
applied to function declarations in clk-provider.h. The definitions
exist in drivers/clk/clk.c. An example error:
In file included from arch/arm/mach-omap2/clockdomain.c:25:0:
arch/arm/mach-omap2/clockdomain.c: In function ‘clkdm_clk_disable’:
include/linux/clk-provider.h:338:12: error: inlining failed in call to always_inline ‘__clk_get_enable_count’: function body not available
arch/arm/mach-omap2/clockdomain.c:1001:28: error: called from here
make[1]: *** [arch/arm/mach-omap2/clockdomain.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
This patch removes the use of inline from include/linux/clk-provider.h
but keeps the function definitions in drivers/clk/clk.c as inlined since
they are one-liners.
Signed-off-by: Igor Mazanov <i.mazanov@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: improved subject, added changelog]
but only fixed now because no one gave enough material for debugging.
Anyway, these fix the problem that sometimes after a power cut the
file-system is not mountable with the following symptom:
grab_empty_leb: could not find an empty LEB
The fixes make the file-system mountable again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1iao
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.7-rc6' of git://git.infradead.org/linux-ubifs
Pull UBIFS fixes from Artem Bityutskiy:
"Two patches which fix a problem reported by several people in the
past, but only fixed now because no one gave enough material for
debugging.
Anyway, these fix the problem that sometimes after a power cut the
file-system is not mountable with the following symptom:
grab_empty_leb: could not find an empty LEB
The fixes make the file-system mountable again."
* tag 'upstream-3.7-rc6' of git://git.infradead.org/linux-ubifs:
UBIFS: fix mounting problems after power cuts
UBIFS: introduce categorized lprops counter
kernel booting on a APEI-enabled machines w/ CONFIG_PSTORE_CONSOLE=y (this
is N by default, though).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=CmNn
-----END PGP SIGNATURE-----
Merge tag 'for-v3.7-fixes' of git://git.infradead.org/users/cbou/linux-pstore
Pull pstore fix from Anton Vorontsov:
"A small fixup for the persistent storage subsystem. The bug can
prevent kernel booting on a APEI-enabled machines w/ PSTORE_CONSOLE=y
(this is N by default, though)."
* tag 'for-v3.7-fixes' of git://git.infradead.org/users/cbou/linux-pstore:
pstore: Fix NULL pointer dereference in console writes
Pill i2c fixes from Jean Delvare.
Well, "fixes".. The biggest patch here is actually Jan marking Wolfram
Sang as the main i2c subsystem maintainer, with Jan staying on as the PC
controller maintainer.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-mux-pinctrl: Fix probe error path
MAINTAINERS: i2c: 7 years, this is it
A few fixes for teardown issues that will be rarely seen, plus a fix for
a silly bug in regulator_is_supported_voltage() which shows how often
the answer to the question should be false.
The supported voltage commit is very new as I just edited to add a Cc to
stable, the code itself has been in -next.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HyTz
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few fixes for teardown issues that will be rarely seen, plus a fix
for a silly bug in regulator_is_supported_voltage() which shows how
often the answer to the question should be false.
The supported voltage commit is very new as I just edited to add a Cc
to stable, the code itself has been in -next."
* tag 'regulator-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix voltage check in regulator_is_supported_voltage()
regulator: core: Avoid deadlock when regulator_register fails
Regulator: core: Unregister when gpio request fails.
The only large LOC is seen in WM5102 driver, just writing a bunch of
register updates, but the actual code change is small.
Other than that, all small fixes suitable for rc6.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=d78q
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The only large LOC is seen in WM5102 driver, just writing a bunch of
register updates, but the actual code change is small. Other than
that, all small fixes suitable for rc6."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix mutex deadlock at disconnection
ALSA: fm801: precedence bug in snd_fm801_tea575x_get_pins()
ALSA: es1968: precedence bug in snd_es1968_tea575x_get_pins()
ALSA: hda - Add a missing quirk entry for iMac 9,1
ASoC: core: Double control update err for snd_soc_put_volsw_sx
ASoC: dapm: Use card_list during DAPM shutdown
ASoC: cs42l52: fix the return value of cs42l52_set_fmt()
ASoC: bells: Correct type in sub speaker DAI name for WM5102
ASoC: wm8978: pll incorrectly configured when codec is master
ASoC: mxs-saif: Fix channel swap for 24-bit format
ASoC: bells: Select WM1250-EV1 Springbank audio I/O module
ASoC: bells: Add missing select of WM0010
ASoC: mxs-saif: Add MODULE_ALIAS
ASoC: wm5102: Write register value corrections after SYSCLK is enabled
Commit 13d782f ("sctp: Make the proc files per network namespace.")
changed the /proc/net/sctp/ struct file_operations opener functions to
use single_open_net() and seq_open_net().
Avoid leaking memory by using single_release_net() and seq_release_net()
as the release functions.
Discovered with Trinity (the syscall fuzzer).
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3215 console always has the RAW3215_FIXED flag set, which causes
raw3215_shutdown() not to wait for outstanding I/O requests if an attached
tty gets closed.
The flag however can be simply removed, so we can guarantee that all requests
belonging to the tty have been processed when the tty is closed.
However the tasklet that belongs to the 3215 device may be scheduled even if
there is no tty attached anymore, since we have a race between console and tty
processing.
Thefore unconditional tty_wakekup() in raw3215_wakeup() can cause the following
NULL pointer dereference:
3.465368 Unable to handle kernel pointer dereference at virtual kernel address (null)
3.465448 Oops: 0004 #1 SMP
3.465454 Modules linked in:
3.465459 CPU: 1 Not tainted 3.6.0 #1
3.465462 Process swapper/1 (pid: 0, task: 000000003ffa4428, ksp: 000000003ffb7ce0)
3.465466 Krnl PSW : 0404100180000000 0000000000162f86 (__wake_up+0x46/0xb8)
3.465480 R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:1 PM:0 EA:3
Krnl GPRS: fffffffffffffffe 0000000000000000 0000000000000160 0000000000000001
3.465492 0000000000000001 0000000000000004 0000000000000004 000000000096b490
3.465499 0000000000000001 0000000000000100 0000000000000001 0000000000000001
3.465506 070000003fc87d60 0000000000000160 000000003fc87d68 000000003fc87d00
3.465526 Krnl Code: 0000000000162f76: e3c0f0a80004 lg %r12,168(%r15)
0000000000162f7c: 58000370 l %r0,880
#0000000000162f80: c007ffffffff00 xilf %r0,4294967295
>0000000000162f86: ba102000 cs %r1,%r0,0(%r2)
0000000000162f8a: 1211 ltr %r1,%r1
0000000000162f8c: a774002f brc 7,162fea
0000000000162f90: b904002d lgr %r2,%r13
0000000000162f94: b904003a lgr %r3,%r10
3.465597 Call Trace:
3.465599 (<0400000000000000> 0x400000000000000)
3.465602 <000000000048c77e> raw3215_wakeup+0x2e/0x40
3.465607 <0000000000134d66> tasklet_action+0x96/0x168
3.465612 <000000000013423c> __do_softirq+0xd8/0x21c
3.465615 <0000000000134678> irq_exit+0xa8/0xac
3.465617 <000000000046c232> do_IRQ+0x182/0x248
3.465621 <00000000005c8296> io_return+0x0/0x8
3.465625 <00000000005c7cac> vtime_stop_cpu+0x4c/0xb8
3.465629 (<0000000000194e06> tick_nohz_idle_enter+0x4e/0x74)
3.465633 <0000000000104760> cpu_idle+0x170/0x184
3.465636 <00000000005b5182> smp_start_secondary+0xd6/0xe0
3.465641 <00000000005c86be> restart_int_handler+0x56/0x6c
3.465643 <0000000000000000> 0x0
3.465645 Last Breaking-Event-Address:
3.465647 <0000000000403136> tty_wakeup+0x46/0x98
3.465652
3.465654 Kernel panic - not syncing: Fatal exception in interrupt
01: HCPGIR450W CP entered; disabled wait PSW 00020001 80000000 00000000 0010F63C
The easiest solution is simply to check if tty is NULL in the tasklet.
If it is NULL nothing is to do (no tty attached), otherwise tty_wakeup()
can be called, since we hold a reference to the tty.
This is not nice... but it is a small patch and it works.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On Thu, 2012-11-01 at 16:45 -0700, Michel Lespinasse wrote:
> Looking at the arch/parisc/kernel/sys_parisc.c implementation of
> get_shared_area(), I do have a concern though. The function basically
> ignores the pgoff argument, so that if one creates a shared mapping of
> pages 0-N of a file, and then a separate shared mapping of pages 1-N
> of that same file, both will have the same cache offset for their
> starting address.
>
> This looks like this would create obvious aliasing issues. Am I
> misreading this ? I can't understand how this could work good enough
> to be undetected, so there must be something I'm missing here ???
This turns out to be correct and we need to pay attention to the pgoff as
well as the address when creating the virtual address for the area.
Fortunately, the bug is rarely triggered as most applications which use pgoff
tend to use large values (git being the primary one, and it uses pgoff in
multiples of 16MB) which are larger than our cache coherency modulus, so the
problem isn't often seen in practise.
Reported-by: Michel Lespinasse <walken@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes errors seen in identifying old Samsung SLC, due to the
following commits:
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
Some Samsung NAND with "5-byte" ID really appear to have 6-byte IDs, with
wraparound like:
Samsung K9K8G08U0D
ec d3 51 95 58 ec ec d3
Samsung K9F1G08U0C
ec f1 00 95 40 ec ec f1
Samsung K9F2G08U0B
ec da 10 95 44 00 ec da
This bad wraparound makes it hard to reliably detect the difference
between Samsung SLC with 5-byte ID and Samsung SLC with 6-byte ID.
The fix is to, for now, only use the new Samsung table for MLC. We
cannot support the new SLC (K9FAG08U0M) until Samsung gives better ID
decode information.
Note that this applies in addition to the previous regression fix:
commit bc86cf7af2
mtd: nand: fix Samsung SLC NAND identification regression
Together, these patches completely restore the previous detection
behavior so that we cannot see any more regressions in Samsung SLC NAND
(finger crossed). With luck, I can get a hold of a Samsung
representative and stop having to cross my fingers eventually.
Reported-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
A combination of the following two commits caused a regression in 3.7-rc1
when identifying some Samsung NAND, so that some previously working NAND
were no longer detected properly:
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
Particularly, a regression was seen on Samsung K9F2G08U0B, with the
following full 8-byte READ ID string:
ec da 10 95 44 00 ec da
The basic problem is that Samsung manufactures both SLC and MLC NAND
that use a non-standard decoding table for deriving information from
their IDs. I have heuristically determined that all the chips that use
the new table have ID strings which wrap around after the 6th byte.
Unfortunately, I overlooked the fact that some older Samsung SLC (which
use a different decoding table) have "5 byte ID strings" which also wrap
around after the 6th byte.
This patch re-introduces a distinction between these old and new Samsung
NAND by checking that the 6th byte is non-zero, allowing both old and
new Samsung NAND to be detected properly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The main samsung pinctrl module references the specific exynos4210
pinctrl driver, which selects the main driver in Kconfig.
Making the main driver a silent "bool" option avoid this potential
build error if CONFIG_PINCTRL_SAMSUNG=y && CONFIG_PINCTRL_EXYNOS4=n:
drivers/built-in.o:(.rodata+0x4e4): undefined reference to `exynos4210_pin_ctrl'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit aa731872f7.
As pointed out by Ben Hutchings, this change is not correct.
mdiobus_unregister() can't be called if the bus isn't registered yet,
however this change can result in situations which cause that to
happen.
Part of the confusion here revolves around the fact that the
callers of this module control registration/unregistration,
rather than the module itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip ready check added by the commit 3ac3546e [Always wait for
the chip to be ready] does not work when the register read/write
is word swapped. This check has been added before the WORD_SWAP
register is programmed, so we need to check for swapped register
value as well.
Bit 16 is marked as RESERVED in SMSC datasheet, Steve Glendinning
<steve@shawell.net> checked with SMSC and wrote:
The chip architects have concluded we should be reading PMT_CTRL
until we see any of bits 0, 8, 16 or 24 set. Then we should read
BYTE_TEST to check the byte order is correct (as we already do).
The rationale behind this is that some of the chip variants have
word order swapping features too, so the READY bit could actually
be in any of the 4 possible locations. The architects have confirmed
that if any of these 4 positions is set the chip is ready. The other
3 locations will either never be set or can only go high after READY
does (so also indicate the device is ready).
This change will check for the READY bit at the 16th position. We do
not check the other two cases (bit 8 and 24) since the driver does not
support byte-swapped register read/write.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 175c0dff, drivers uses tasklet_kill to avoid put disabled tasklet
on the tasklet vec. But some of the drivers uses tasklet_init & tasklet_disable
in the driver init code, then tasklet_enable when it is opened. This makes
tasklet_enable on a killed tasklet and make ksoftirqd crazy then. Normally,
drivers should use tasklet_init/tasklet_kill on device open/remove, and use
tasklet_disable/tasklet_enable on device suspend/resume.
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
With the latest kernel there are two things that must be done post decryption
so that the packet are forwarded.
1. Remove the mark from the packet. This will cause the packet to not match
the ipsec-policy again. However doing this causes the post-decryption check to
fail also and the packet will get dropped. (cat /proc/net/xfrm_stat).
2. Remove the sp association in the skbuff so that no policy check is done on
the packet for VTI tunnels.
Due to #2 above we must now do a security-policy check in the vti rcv path
prior to resetting the mark in the skbuff.
Signed-off-by: Saurabh Mohan <saurabh.mohan@vyatta.com>
Reported-by: Ruben Herold <ruben@puettmann.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing a NULL id causes a NULL pointer deference in writers such as
erst_writer and efi_pstore_write because they expect to update this id.
Pass a dummy id instead.
This avoids a cascade of oopses caused when the initial
pstore_console_write passes a null which in turn causes writes to the
console causing further oopses in subsequent pstore_console_write calls.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
commit 611ae8e3f5204f7480b3b405993b3352cfa16662('enable tlb flush range
support for x86') change flush_tlb_mm_range() considerably. After this,
we test whether vmflag equal to VM_HUGETLB and it may be always failed,
because vmflag usually has other flags simultaneously.
Our intention is to check whether this vma is for hughtlb, so correct it
according to this purpose.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Acked-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1352740656-19417-1-git-send-email-js1304@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The spi_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull power tools fixes from Len Brown:
"A pair of power tools patches -- a 3.7 regression fix plus a bug fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: graceful fail on garbage input
tools/power turbostat: Repair Segmentation fault when using -i option
Pull MIPS update from Ralf Baechle:
"To avoid unnecessary risk and work the preemption fixes are combined
with some preparatory work that isn't strictly required. So it's
really just 3 fixes:
- Get is_compat_task() to do the right thing while simplifying it.
The unnecessary complexity hid a rarely striking bug which could be
triggered by ext3/ext4 under certain circumstances.
- Resolve a preemption issue in the irqflags.h functions for kernels
built to support pre-MIPS32 / pre-MIPS64 Release 2 processors.
- Fix the interrupt number of the MIPS Malta's CBUS UART."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Malta: Fix interupt number of CBUS UART.
MIPS: Make irqflags.h functions preempt-safe for non-mipsr2 cpus
MIPS: Remove irqflags.h dependency from bitops.h
MIPS: bitops.h: Change use of 'unsigned short' to 'int'
MIPS: compat: Delete now unused TIF_32BIT.
MIPS: compat: Implement is_compat_task() by testing for 32-bit address space.
MIPS: compat: Fix use of TIF_32BIT_ADDR vs _TIF_32BIT_ADDR
Pull cgroup fixes from Tejun Heo:
"This contains two fix patches for device_cgroup. One fixes a
regression introduced earlier in 3.7 cycle where device_cgroup could
try to dereference the NULL parent of the root cgroup. The other one
is RCU usage fix."
* 'for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: fix RCU usage
device_cgroup: fix unchecked cgroup parent usage
Commit bdb498c200 "TTY: hvc_console, add tty install" took the port
refcounting out of hvc_open()/hvc_close(), but failed to remove the
kref_put() and tty_kref_put() calls in hvc_hangup() that were there to
remove the extra references that hvc_open() had taken.
The result was that doing a vhangup() when the current terminal was
a hvc_console, then closing the current terminal, would end up calling
destroy_hvc_struct() and making the port disappear entirely. This
meant that Fedora 17 systems would boot up but then not display the
login prompt on the console, and attempts to open /dev/hvc0 would
give a "No such device" error.
This fixes it by removing the extra kref_put() and tty_kref_put() calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old ifdef CONFIG_BRCMFISCAN looks wrong to me and it makes more
sense when CONFIG_BRCMISCAN is used.
This patch was just compile tested by me, but not runtime tested.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.
This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.
After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.
This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The recent change for USB-audio disconnection race fixes introduced a
mutex deadlock again. There is a circular dependency between
chip->shutdown_rwsem and pcm->open_mutex, depicted like below, when a
device is opened during the disconnection operation:
A. snd_usb_audio_disconnect() ->
card.c::register_mutex ->
chip->shutdown_rwsem (write) ->
snd_card_disconnect() ->
pcm.c::register_mutex ->
pcm->open_mutex
B. snd_pcm_open() ->
pcm->open_mutex ->
snd_usb_pcm_open() ->
chip->shutdown_rwsem (read)
Since the chip->shutdown_rwsem protection in the case A is required
only for turning on the chip->shutdown flag and it doesn't have to be
taken for the whole operation, we can reduce its window in
snd_usb_audio_disconnect().
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the firmware is in SNIFFER mode, it leaves
the FCS at the end of frame. Not telling mac80211
means it won't add the right flag to the radiotap
header and that confuses wireshark.
Since mac80211 doesn't have a per-packet flag, set
the HW flag dynamically. This works as the monitor
vif can only be present in the driver by itself.
This fixes a regression introduced by my
commit 5789772641
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri May 11 10:53:18 2012 +0200
iwlwifi: support explicit monitor interface
Cc: stable@vger.kernel.org [3.5+]
Reported-by: MARK PHILLIPS <mark.phillips@virgin.net>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.
This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[wsa: improved the commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
There is a precedence bug because | has higher precedence than ?:. This
code was cut and pasted and I fixed a similar bug a few days ago.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.
- We set the default maximum to 0xFFFF because there are several
devices out there that only support two-byte block counts even with
WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
LIMITS VPD.
- max_write_same_blocks can be overriden per-device basis in sysfs.
- The UNMAP discovery heuristics remain unchanged but the discard
limits are tweaked to match the "real" WRITE SAME commands.
- In the error handling logic we now distinguish between WRITE SAME
with and without UNMAP set.
The discovery process heuristics are:
- If the device reports a SCSI level of SPC-3 or greater we'll issue
READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
supported. If that's the case we will use it.
- If the device supports the block limits VPD and reports a MAXIMUM
WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).
- Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
0xFFFFFFFF or the block count exceeds 0xFFFF.
- no_write_same is set for ATA, FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support requests with more than one bio payload for discards. The total
number of bytes to be discarded is stored in req->__data_len and used in
sd_done() to complete the I/O.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.
We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
