o use a semaphore instead of an opencoded and racy lock
o move locking out of shaper_kick and into the callers - most just
released the lock before calling shaper_kick
o remove in_interrupt() tests. from ->close we can always block, from
->hard_start_xmit and timer context never
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The times when tricky goto's produced better codes are long gone.
This patch should express the same in a better way.
(Also fixes the final gcc-4.0 x86 compile error)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add tg3_nvram_lock() and tg3_nvram_unlock() calls around tg3_halt_cpu().
It is possible that the bootcode may be loading code from nvram during
this call and stopping the cpu without getting the lock may cause
uncompleted nvram data to be left in the nvram data register. Subsequent
calls to read/write nvram data will fail.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test uses the previously added tg3_test_interrupt() to perform the
test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test will loopback one packet in MAC loopback mode and verify the
packet data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reset kind parameter to tg3_halt() so that the RESET_KIND_SUSPEND
parameter can be passed to tg3_halt() before doing offline tests.
All other calls to tg3_halt() will use the RESET_KIND_SHUTDOWN
parameter.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and remove duplicate status defines.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Index: linux-2.6/drivers/net/smc91x.c
===================================================================
- more consistent prototypes;
- rtl8169_rx_interrupt()
o the error condition should be rare;
o goto removal.
Signed-off-by: Richard Dawe <rich@phekda.gotadsl.co.uk>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
There aren't lots of statistics available, but this is what is available
according to the RealTek documentation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Also:
- ratelimit the too much work at interrupt message, so if under massive
packet load the console doesn't get flooded;
- removal of a few PFX used in contexts where dev->name is available;
- s/->slot_name/pci_name/;
- printed_version is redundant with the debug option. Remove it and let
the user decide.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
To tell if driver is configured for NAPI or not, put -NAPI on driver
version. Remove the NAPI printk since the complete version information
is displayed once in the pci probe routine or returned via ethtool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The USR 997902 is based on the 8169 chipset.
The value has been extracted from the sources of the driver which
comes with the manufacturer's cdrom. Heads-up and test by TommyDrum
<mycooc@yahoo.it>.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
A new driver bnx2 for Broadcom bcm5706 is available.
The patch also includes new 1000BASE-X advertisement bit definitions in
mii.h
Thanks to David Miller and Jeff Garzik for reviewing and their valuable
feedback.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correcting the list traversal makes the problem go away.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'if' clause for ULI526X in tulip_mdio_write allows for
spin_unlock_irqrestore to be called twice for tp->mii_lock. I believe
this is caused by the unintentional omission of a return at the end
of that clause. This patch adds that return.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 0x1601 as 5752M, it's a 5752 but for mobile PCs.
Stolen from Broadcom bcm5700-8.1.55 driver.
Someone forgot to add it to tg3 ;-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract DMA boundary bit selection into a seperate
function, tg3_calc_dma_bndry(). Call this from
tg3_test_dma().
Make DMA test more reliable by using no DMA boundry
setting during the test. If the test passes, then
use the setting we selected before the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Even though we do software interrupt mitigation
via NAPI, it still helps to have some minimal
hw assisted mitigation.
This helps, particularly, on systems where register
I/O overhead is much greater than the CPU horsepower.
For example, it helps on NUMA systems. In such cases
the PIO overhead to disable interrupts for NAPI accounts
for the majority of the packet processing cost. The
CPU is fast enough such that only a single packet is
processed by each NAPI poll call.
Thanks to Michael Chan for reviewing this patch.
Signed-off-by: David S. Miller <davem@davemloft.net>
When supported, use the TAGGED interrupt processing support
the chip provides. In this mode, instead of a "on/off" binary
semaphore, an incrementing tag scheme is used to ACK interrupts.
All MSI supporting chips support TAGGED mode, so the tg3_msi()
interrupt handler uses it unconditionally. This invariant is
verified when MSI support is tested.
Since we can invoke tg3_poll() multiple times per interrupt under
high packet load, we fetch a new copy of the tag value in the
status block right before we actually do the work.
Also, because the tagged status tells the chip exactly which
work we have processed, we can make two optimizations:
1) tg3_restart_ints() need not check tg3_has_work()
2) the tg3_timer() need not poke the chip 10 times per
second to keep from losing interrupt events
Based upon valuable feedback from Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 2 of the 3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 is not
supported by the prism54 project. To stop confusion, the kernel
documentation should state so as 3com made a good job hiding the version.
Signed-off-by: Andrew Morton <akpm@osdl.org>
diff -puN drivers/net/wireless/Kconfig~wireless-3crwe154g72-kconfig-help-fix drivers/net/wireless/Kconfig
This patch reduces the stack usage of the function smc91c92_event() in
smc91c92_cs driver from 3540 to 132. Currently this is the highest stack
user in linux-2.6.12-rc2-mm3. I used a patched version of gcc 3.4.3 on
i386 with -fno-unit-at-a-time disabled.
The patch has only been compile tested.
Acked-by: Jrn Engel <joern@wohnheim.fh-wedel.de>
Acked-by: Randy Dunlap <rddunlap@osdl.org>
Signed-off-by: Yum Rayan <yum.rayan@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This has been a problem for me for ages. When using bridging, the driver
is switched into promiscuous mode before the link init is complete. The
init complete routine then resets the promisc bit on the card so the kernel
still thinks the card is in promiscuous mode but the card isn't. doh.
I think this bug only shows up in bridging when the bridge is started at
boot time (or something else that sets promisc at the same time the card
was started). If promisc is enabled later it works.
Here's a trivial (and hopefully correct) patch that works for me. It
just calls the promisc/multicast setup routine after init.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix IBM EMAC driver ioctl bug.
I found IBM EMAC driver bug.
So mii-tool command print wrong status.
# mii-tool
eth0: 10 Mbit, half duplex, no link
eth1: 10 Mbit, half duplex, no link
I can get correct status on fixed kernel.
# mii-tool
eth0: negotiated 100baseTx-FD, link okZZ
eth1: negotiated 100baseTx-FD, link ok
Hiroaki Fuse
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> for CELF
The attached patch updates generic HDLC to version 1.18.
FR Cisco LMI production-tested. Please apply to Linux 2.6. Thanks.
Changes:
- doc updates
- added Cisco LMI support to Frame-Relay code
- cleaned hdlc_fr.c a bit, removed some orphaned #defines etc.
- fixed a problem with non-functional LMI in FR DCE mode.
- changed diagnostic messages to better conform to FR standards
- all protocols: information about carrier changes (DCD line) is now
printed to kernel logs.
Signed-Off-By: Krzysztof Halasa <khc@pm.waw.pl>
NET_WIRELESS is only a subset of the stuff in drivers/net/wireless;
NET_RADIO is what covers all of them.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
This patch removes a file that seems to be used only on AIX (sic).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch adds support for the davicom dm9000 network driver. The dm9000
is found on some embedded arm boards such as the pimx1 or the scb9328.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
diff -puN /dev/null drivers/net/dm9000.c
The module parameter values got lost in the conversion to the new module_param
interface. This should fix it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Index: tlan/drivers/net/tlan.c
===================================================================
This patch fixes the following compile error caused by bk-netdev:
<-- snip -->
...
LD .tmp_vmlinux1
drivers/built-in.o(.text+0x98528): In function `sis900_get_settings':
: undefined reference to `mii_ethtool_gset'
drivers/built-in.o(.text+0x98538): In function `sis900_set_settings':
: undefined reference to `mii_ethtool_sset'
drivers/built-in.o(.text+0x98517): In function `sis900_get_link':
: undefined reference to `mii_link_ok'
drivers/built-in.o(.text+0x98547): In function `sis900_nway_reset':
: undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Daniele Venzano <venza@brownhat.org>
When running the loopback test, resources are not properly released on
completion. This patch frees all transmit resources after running the
loopback test. Tested on ia32 and ppc64 hardware.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
This patch brings the airo driver into line with the current
WEXT specification of signal quality. It also fixes the values
used to determine signal quality and level for MPI & PCMCIA 350
cards. It turns out that BSSListRid.rssi was actually in dBm
for 350 series cards, and that we can use the normalized
signal strength reported by the card as our "quality" value, on
a scale of 0 - 100. Since signal level values are in dBm for
this driver, max_qual->level MUST be 0, as specified in the WEXT
spec. This patch also uses the IW_QUAL constants new in WEXT
version 17.
Signed-off-by: Dan Williams <dcbw@redhat.com>
On Wed, Apr 13, 2005 at 05:36:42PM +0000, Andrew Morton wrote:
> Summary: natsemi: incorrect initialization of IPv6 Neighbor-
> discovery multicast
I've got a pair of FA312 cards and this problem has bothered me
for ages. This has finally prompted me to do something about it :)
Turns out that somebody wasn't following the documentation. We were
doing 16-bit writes to 32-bit registers which led to some addresses
working and others not so lucky.
This patch should fix the problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ayaz wrote an update to the error handling for forcedeth (which I
modified heavily, thus all bugs are mine):
The ERROR4 bit is not a fatal error, it just indicates a mismatch
between the actual packet len and the len according to the 802.3 header.
The patch adds proper handling.
The patch also removes the code that drops all packets with RX_ERROR &
(!RX_FRAMINGERR): ERROR4 errors are also not fatal.
Hi Andrew, Jeff,
The iseries_veth driver is badly behaved in that it will keep TX packets
hanging around forever if they're not ACK'ed and the queue never fills up.
This causes the unregister_netdevice code to wait forever when we try to take
the device down, because there's still skbs around with references to our
struct net_device.
There's already code to cleanup any un-ACK'ed packets in veth_stop_connection()
but it's being called after we unregister the net_device, which is too late.
The fix is to rearrange the module exit function so that we cleanup any
outstanding skbs and then unregister the driver.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Hi Andrew, Jeff,
Under some strange circumstances the iseries_veth driver can leak skbs.
Fix is simply to call dev_kfree_skb() in the right place.
Fix up the comment as well.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Hi Andrew, Jeff,
The iseries_veth driver doesn't set dev->trans_start in it's TX path. This
will cause the net device watchdog timer to fire earlier than we want it to,
which causes the driver to needlessly reset its connections to other LPARs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Hi Andrew, Jeff,
The iseries_veth driver has a logic bug which means it will erroneously
send packets to LPARs for which we don't have a connection.
This usually isn't a big problem because the Hypervisor call fails
gracefully and we return, but if packets are TX'ed during the negotiation
of the connection bad things might happen.
Regardless, the right thing is to bail early if we know there's no
connection.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
small fixes from CVS that didn't fit elsewhere
Index: linux-2.6/drivers/net/wireless/orinoco.c
===================================================================
The options FMV18X and SK_G16 do depend on the non-available
CONFIG_OBSOLETE even in kernel 2.4 - IOW, the last time it was able to
select them was in kernel 2.2 (or even before).
Since it seems noone misses these drivers, this patch removes them.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch removes a NULL check that was useles because it happened
after the first dereference of the variable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains the following cleanups:
- make a needlessly global function static
- make three needlessly global structs static const
Since after moving the now-static stucts to smc-mca.c the file smc-mca.h
was empty except for two #define's, I've also killed the rest of
smc-mca.h .
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use msleep() instead of schedule_timeout()
to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Phil Blundell <pb@nexus.co.uk>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
