A value of 0 means indefinite repetition (until interrupted).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was only ever needed for an FPGA version of Falcon.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set dummy monitor method for unrecognised boards.
Clean up board resources if efx_pci_probe_main() fails after board has
been initialised.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the KS8695 ethernet device (ks8695net).
This driver is only of use on the KS8695 which is an ARM9 based SoC. The
documentation on this SoC is sparse and poor, with barely a register
description and a rough outline of how the ethernet works, this driver was
therefore written with strong reference to the Micrel supplied Linux 2.6.9
port, and to Andrew Victor's ks8695eth driver.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Acked-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip can strip CRC automatically on receiving. Enable it.
Also fix potential RX_BUF_SIZE calculation bug which was obscured by
alignment. And use proper symbols (NET_IP_ALIGN, ETH_FCS_LEN, etc.)
instead of magic numbers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for the LAN9240 PCI ethernet adapter.
Changes since initial submission:
- debug msg_level has been changed to use standard definitions
- convert to use net_device_ops
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Peter Waskiewicz patch for ixgbe. Add error handling based on
Hemminger's recommendation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the driver to select 16-bit or 32-bit bus access at runtime,
at a small performance cost.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the PCIe Advanced Error Reporting callbacks in
ixgbe. The 82598 hardware supports AER, so we enable it.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a virtual environment the ports of an 82575/6 can appear to
be single function devices which is not correct. To resolve this we rely
on the function number stored in the status register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we begin to move into virtualization the use of a global value for
buffer sizes becomes undesirable. This change makes it so only 256 and 512
byte buffers require use of the RCTL register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_parse_parm() parses a parameter table for a particular value and
is therefore not modifying the table at all. Therefore make the 2nd
argument const, thus allowing to make the tables const later.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some declarations from bonding.c as they are declared in bonding.h
already.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_debug() instead of own macros.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is what I get if debug is enabled:
drivers/net/bonding/bond_ipv6.c: In function 'bond_na_send':
drivers/net/bonding/bond_ipv6.c:75: error: 'slave' undeclared (first use in this function)
drivers/net/bonding/bond_ipv6.c:75: error: (Each undeclared identifier is reported only once
drivers/net/bonding/bond_ipv6.c:75: error: for each function it appears in.)
This patch fixes that.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a small array in bond_mode_name() for the names, thus saving some
space:
before
text data bss dec hex filename
57736 9372 344 67452 1077c drivers/net/bonding/bonding.ko
after
text data bss dec hex filename
57441 9372 344 67157 10655 drivers/net/bonding/bonding.ko
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce and use bond_is_lb(), it is usefull to shorten the repetitive
check for either ALB or TLB mode.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds LSI ET1011C PHY driver.
This driver is used by TI DM646x EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a fragmentation check to myri10ge's LRO get_frag_header() callback.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/hydra.c:163: error: 'hydra_netdev_ops' undeclared (first use in this function)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last shoot of this series.
After I removing all directly reference of netdev->priv, I am killing
"priv" of "struct net_device" and fixing relative comments/docs.
Anyone will not be allowed to reference netdev->priv directly.
If you want to reference the memory of private data, use netdev_priv()
instead.
If the private data is not allocted when alloc_netdev(), use
netdev->ml_priv to point that memory after you creating that private
data.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect use of loose in spider_net.c
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have various drivers that poke around directly and we need to clean this
up before it causes problems.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change interrupt vector naming to match recent changes from Robert Olsson.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using GFP_KERNEL was wrong and produces a 'scheduling while atomic'
bug as we're in a tasklet. Also, check for proper return values
now, in case allocation fails and be sure to stop the TX queue
in case of memory issues but gaurantee the TX queue will
eventually be woken up.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pci_map_single() can fail so detect those errors with
pci_dma_mapping_error() and deal with them accordingly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Request the AID from hardware and provide this id
to the driver (in case they need it).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all code which determines the right TX descriptor
fields specific to crypto support into rt2x00crypto.c.
This makes the code in rt2x00queue more simpler and
better concentrates all crypto code into a single location.
With this we can also remove some ifdefs in rt2x00queue.c
since the code inside the ifdef is either very small, or
only calling empty functions (see empty function definitions
in rt2x00lib.h).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix ERP configuration, due to a too strict changes
flags checking we never updated the short slot time
or basic rate mask when no other changes were made
at the same time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for the introduction of a generic swap() macro.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers should notify rt2x00lib when they provide
the IV/ICV data. This adds some flexibility to drivers
which can't provide all information.
* rt2500usb provides ICV inside the frame
* rt2800pci doesn't provide IV/ICV
* rt2800usb doesn't provide IV/ICV
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch does following things
1) This patch fixes the a-band association for passive channels with new
uCode feature that it allows direct scan on passive channels after
auto-switch from passive to active. This enables sending of direct probes
on passive channels, as long as some traffic is detected on that channel.
This improves the scanning for hidden SSIDs in A-band,which is all
passive channels.
This patch fixes the bug no 1748.
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1748
2) This fix will only work with uCode version 15.28.2.8 and above.
Prior versions of uCode would work only if we heard the traffic within
active dwell time, which is much shorter than passive dwell time and
is shorter than typical beacon periods. This patch also provids full
active dwell time even if we hear traffic late in passive dwell.
3) uCode API version is incremented to 2.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the infrastructure to support older firmware APIs.
The API version number is stored as part of the filename, we first try to
load the most recent firmware and progressively try lower versions.
The API version is also read from the firmware self and stored as part
of the iwl_priv structure. Only firmware that is supported by driver will
be loaded. The version number read from firmware is compared
to supported versions in the driver not the API version used as part of
filename.
An example using this new infrastrucure:
if (IWL_UCODE_API(priv->ucode_ver) >= 2) {
Driver interacts with Firmware API version >= 2.
} else {
Driver interacts with Firmware API version 1.
}
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We store the ucode version number as part of
iwl_priv/iwl3945_priv. This enables us to determine
if particular ucode has support for features in order
to have driver support more than one ucode API.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the misuse of DMA channel number by Tx queue number in
iwl_tx_ctx_stop().
The problem was originally reported by Wu Fengguang who complains
iwlagn driver takes too long time when issuing `ifconfig wlan0 down`.
The patch now decreases the interface bring down time from 2 seconds
to 0.8 second.
This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11956http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1790
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 rate scaling was broken in recent tree. This patch fix the following:
1- Get TX response info and update rates window.
2- Rate scaling selection.
3- Flush window timer.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add debugfs support to 3945 driver to display rs info.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves channels info display from sysfs to debugfs.
This shows channel information as stored in NIC EEPROM. This
is useful in debugging CRDA or iwl goes setting so it belongs
rather to debugfs then to sysfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_enable_interrupts and iwl_disable_interrupts
functions to iwl-core.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The find_station routine needs to look at the IWL_AP_ID entry if we're a STA.
Currently, it only looks for STA entries which causes HW crypto to fail.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_check_rxon_cmd into iwl-agn-hcmd-check.c
This function compiled out in none debugging or non development
mode and more. We haven't decided which one yet hence preserving the
current 'always compile' state.
More functions will be added to the file namely for checking TX and LQ
commands.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb supports hardware encryption.
rt2500usb supports up to 4 shared and pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify rt2x00lib_config_antenna() by moving
duplicate code into a seperate static inlined
function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
