Commit Graph

2068 Commits

Author SHA1 Message Date
Bartlomiej Zolnierkiewicz
c754d9b6e0 pata_cmd64x: remove unused definitions
s/ARTIM2/ARTTIM23/ in cmd648_bmdma_stop() while at it

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:45 -05:00
Bartlomiej Zolnierkiewicz
03a849e6dd pata_cmd64x: cmd648_bmdma_stop() fix
Clear the primary channel pending interrupt bit
instead of the reserved one.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:45 -05:00
Bartlomiej Zolnierkiewicz
d62f5576ef pata_cmd64x: fix handling of address setup timings
Account for the requirements of the DMA mode currently used
by the pair device.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
Bartlomiej Zolnierkiewicz
a2bd62207a pata_cmd64x: fix PIO setup
Fix incorrect handling of recovery clocks value == 16 resulting
in overclocked recovery timings & potentially underclocked active
timings.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
Bartlomiej Zolnierkiewicz
d8b3d8cfe6 pata_ali: documentation fixes
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
Bartlomiej Zolnierkiewicz
9e8808a99c libata: fix CFA handling in ide_timing_compute()
Use standard cycle timing for CFA PIO5 and PIO6 modes.

Based on commit 74638c8 for IDE subsystem.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
Bart Hartgers
02d1d6160f sata_via: Correctly setup PIO/DMA for pata slave on vt6421.
Before only the timings for master were set. Datasheet can be found
here: ftp://ftp.vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF
Surprisingly, a slave drive works without this patch. According to the
datasheet, the controller by default derives the DMA mode from the
Set Features command issued to a drive. Not sure about the PIO
timings, though. The real problem is that the timings for the master
effectively are the ones tuned for the slave. If these support
different UDMA-settings, there is trouble, especially when the slave
supports a higher UDMA than the master.

Anyhow, using the same mechanism for both master and slave seems like
a good idea.

Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
Robert Hancock
9ffc5da5e1 libata: make functions/variables static
Make some variables in ahci and a function in pata_pcmcia static, as found
using sparse.

Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
Tejun Heo
27943620cb libata: implement spurious irq handling for SFF and apply it to piix
Traditional IDE interface sucks in that it doesn't have a reliable IRQ
pending bit, so if the controller raises IRQ while the driver is
expecting it not to, the IRQ won't be cleared and eventually the IRQ
line will be killed by interrupt subsystem.  Some controllers have
non-standard mechanism to indicate IRQ pending so that this condition
can be detected and worked around.

This patch adds an optional operation ->sff_irq_check() which will be
called for each port from the ata_sff_interrupt() if an unexpected
interrupt is received.  If the operation returns %true,
->sff_check_status() and ->sff_irq_clear() will be cleared for the
port.  Note that this doesn't mark the interrupt as handled so it
won't prevent IRQ subsystem from killing the IRQ if this mechanism
fails to clear the spurious IRQ.

This patch also implements ->sff_irq_check() for ata_piix.  Note that
this adds slight overhead to shared IRQ operation as IRQs which are
destined for other controllers will trigger extra register accesses to
check whether IDE interrupt is pending but this solves rare screaming
IRQ cases and for some curious reason also helps weird BIOS related
glitch on Samsung n130 as reported in bko#14314.

  http://bugzilla.kernel.org/show_bug.cgi?id=14314

* piix_base_ops dropped as suggested by Sergei.

* Spurious IRQ detection doesn't kick in anymore if polling qc is in
  progress.  This provides less protection but some controllers have
  possible data corruption issues if the wrong register is accessed
  while a command is in progress.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Hans Werner <hwerner4@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
Tejun Heo
d88ec2e5c1 libata: cleanup ata_sff_interrupt()
host->ports[i] is never NULL if i < host->n_ports and non-NULL return
from ata_qc_from_tag() guarantees that the returned qc is active.
Drop unnecessary tests.

Superflous () dropped as suggested by Sergei.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
Seth Heasley
88e8201e67 ata_piix: IDE Mode SATA patch for Intel Cougar Point DeviceIDs
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:43 -05:00
Seth Heasley
5623cab83e ahci: AHCI and RAID mode SATA patch for Intel Cougar Point DeviceIDs
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:43 -05:00
Shane Huang
d6ef31539d ahci: Implement SATA AHCI FIS-based switching support
Tested on AMD internal reference board.

Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:43 -05:00
Sergei Shtylyov
d817898c2f pata_hpt366: remove irrelevant TODO
HPT36x chips just don't have DPLL.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:43 -05:00
Sergei Shtylyov
fd5e62e22d pata_hpt{37x|3x2n}: improve timing register documentation
Describe UDMA timing bits 18-20 and 21 separately; add a note to bit
31 about it being meaningful for PIO only.  Reformat the whole comment,
while at it...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:43 -05:00
Sergei Shtylyov
859faa875e pata_hpt366: remove redundant code
There's no need to clear the fast interrupt bit in hpt366_set_mode()
since we're doing it in hpt366_init_chipset() already.

While at it, rename 'addr1' local variable to 'addr' and
exclude 'ap->port_no' from its calculation as HPT36x are
single-channel-per-function chips.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:43 -05:00
Sergei Shtylyov
1a1b172b96 pata_hpt{37x|3x2n}: unify mode programming
As these drivers' set_piomode() and set_dmamode() methods are almost
identical, factor out the common hpt{37x|3x2n}_set_mode() function
to be called by both of them, the same as in 'pata_hpt366' driver.

This results in ~5% decrease in the 'pata_hpt37x' driver binary
size and in ~4% decrease in the 'pata_hpt3x2n' driver binary size
(as measured on x86-32).

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:43 -05:00
Sergei Shtylyov
6066193399 pata_hpt3x2n: always stretch UltraDMA timing
The UltraDMA Tss timing must be stretched with ATA clock of 66 MHz, but the
driver only does this when PCI clock is 66 MHz, whereas it always programs
DPLL clock (which is used as the ATA clock) to 66 MHz.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:42 -05:00
Sergei Shtylyov
56f46f8c87 pata_hpt37x: use ATA_DMA_* constants
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE registers.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:42 -05:00
Linus Torvalds
bc53515413 Merge branch 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: replace acpi_integer by u64
  ACPICA: Update version to 20100121.
  ACPICA: Remove unused uint32_struct type
  ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
  ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
  ACPICA: Predefined name repair: fix NULL package elements
  ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
  ACPICA: Update all ACPICA copyrights and signons to 2010
  ACPICA: Update for new gcc-4 warning options
2010-03-01 10:36:22 -08:00
Linus Torvalds
b1bf936840 Merge branch 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
  block: don't access jiffies when initialising io_context
  cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
  block: fix for "Consolidate phys_segment and hw_segment limits"
  cfq-iosched: quantum check tweak
  blktrace: perform cleanup after setup error
  blkdev: fix merge_bvec_fn return value checks
  cfq-iosched: requests "in flight" vs "in driver" clarification
  cciss: Fix problem with scatter gather elements in the scsi half of the driver
  cciss: eliminate unnecessary pointer use in cciss scsi code
  cciss: do not use void pointer for scsi hba data
  cciss: factor out scatter gather chain block mapping code
  cciss: fix scatter gather chain block dma direction kludge
  cciss: simplify scatter gather code
  cciss: factor out scatter gather chain block allocation and freeing
  cciss: detect bad alignment of scsi commands at build time
  cciss: clarify command list padding calculation
  cfq-iosched: rethink seeky detection for SSDs
  cfq-iosched: rework seeky detection
  block: remove padding from io_context on 64bit builds
  block: Consolidate phys_segment and hw_segment limits
  ...
2010-03-01 09:00:29 -08:00
Martin K. Petersen
8a78362c4e block: Consolidate phys_segment and hw_segment limits
Except for SCSI no device drivers distinguish between physical and
hardware segment limits.  Consolidate the two into a single segment
limit.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-02-26 13:58:08 +01:00
Martin K. Petersen
086fa5ff08 block: Rename blk_queue_max_sectors to blk_queue_max_hw_sectors
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.

Also introduce a temporary wrapper for backwards compability.  This can
be removed after the merge window is closed.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-02-26 13:58:08 +01:00
Robert Hancock
453d3131ec ahci: disable FPDMA auto-activate optimization on NVIDIA AHCI
Mike Cui reported that his system with an NVIDIA MCP79 (aka MCP7A)
chipset stopped working with 2.6.32. The problem appears to be that
2.6.32 now enables the FPDMA auto-activate optimization in the ahci
driver. The drive works fine with this enabled on an Intel AHCI so
this appears to be a chipset bug.  Since MCP79 is a fairly recent
NVIDIA chipset and we don't have any info on whether any other NVIDIA
chipsets have this issue, disable FPDMA AA optimization on all NVIDIA
AHCI controllers for now.

Should address http://bugzilla.kernel.org/show_bug.cgi?id=14922

Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
While-we-investigate-issue-this-patch-looks-good-to-me-by:
	Prajakta Gudadhe <pgudadhe@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
2010-02-24 22:44:48 -05:00
Daniel Mack
3ad2f3fbb9 tree-wide: Assorted spelling fixes
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-02-09 11:13:56 +01:00
Adam Buchbinder
c9404c9c39 Fix misspelling of "should" and "shouldn't" in comments.
Some comments misspell "should" or "shouldn't"; this fixes them. No code changes.

Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-02-05 12:22:30 +01:00
Catalin Marinas
2d68b7fe55 [libata] Call flush_dcache_page after PIO data transfers in libata-sff.c
flush_dcache_page() must be called after (!ATA_TFLAG_WRITE) the
data copying to avoid D-cache aliasing with user space or I-D cache
coherency issues (when reading data from an ATA device using PIO,
the kernel dirties the D-cache but there is no flush_dcache_page()
required on Harvard architectures).

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-02-04 01:04:50 -05:00
Tejun Heo
cedc9bf906 ahci: add Acer G725 to broken suspend list
Acer G725 shares the same suspend problem with the HP laptops which
lose ATA devices on resume.  New firmware which fixes the problem is
already available.  Add G725 with old firmwares to the broken suspend
list.

This problem has been reported in bko#15104.

  http://bugzilla.kernel.org/show_bug.cgi?id=15104

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jani-Matti Hätinen <jani-matti.hatinen@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-02-04 01:01:39 -05:00
Douglas Gilbert
bc496ed00a libata-scsi passthru: fix bug which truncated LBA48 return values
Fix assignment which overwrote SAT ATA PASS-THROUGH command EXTEND
bit setting (ATA_TFLAG_LBA48)

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-02-04 01:01:22 -05:00
Lin Ming
439913fffd ACPI: replace acpi_integer by u64
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.

Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-01-28 01:47:33 -05:00
Tejun Heo
534ead7092 libata: retry FS IOs even if it has failed with AC_ERR_INVALID
libata currently doesn't retry if a command fails with AC_ERR_INVALID
assuming that retrying won't get it any further even if retried.
However, a failure may be classified as invalid through hardware
glitch (incorrect reading of the error register or firmware bug) and
there isn't whole lot to gain by not retrying as actually invalid
commands will be failed immediately.  Also, commands serving FS IOs
are extremely unlikely to be invalid.  Retry FS IOs even if it's
marked invalid.

Transient and incorrect invalid failure was seen while debugging
firmware related issue on Samsung n130 on bko#14314.

  http://bugzilla.kernel.org/show_bug.cgi?id=14314

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-20 14:25:11 -05:00
Tejun Heo
5040ab67a2 libata: retry link resume if necessary
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure.  Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-12 14:34:14 -05:00
Tejun Heo
0b67c7439f ata_piix: enable 32bit PIO on SATA piix
Commit 871af1210f enabled 32bit PIO for
PATA piix but didn't for SATA.  There's no reason not to use 32bit PIO
on SATA piix.  Enable it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-12 14:33:23 -05:00
Mikael Pettersson
a2342f4643 sata_promise: don't classify overruns as HSM errors
When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.

Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.

This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.

This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: thomas schorpp <thomas.schorpp@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-12 14:33:07 -05:00
Len Brown
fcb11235d3 Merge branch 'misc-2.6.33' into release 2009-12-24 01:19:00 -05:00
Carlos R. Mafra
2370b5ed03 ACPI: do not select ACPI_DOCK from ATA_ACPI
In March 2008 commit 0ac4a3c2fb ("ACPI: fix
ATA_ACPI build") made CONFIG_ACPI_DOCK be selected by CONFIG_ATA_ACPI because
of a build error when CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m.

However, in September 2008 commit 898b054f3e
("dock: make dock driver not a module") removed the possibility of having
CONFIG_ACPI_DOCK=m and therefore there is no need for selecting it when
CONFIG_ATA_ACPI=y.

This makes the kernel ~5 Kb smaller for people who don't have a dock by
allowing them to not have ACPI_DOCK compiled-in because of ATA_ACPI=y.

Signed-off-by: Carlos R. Mafra <crmafra@aei.mpg.de>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-12-24 00:04:40 -05:00
Sonic Zhang
3439d65062 pata_bf54x: handle portmuxing of pins through GPIO PORTs
By default, the PATA pins are routed to the async address lines in which
case, no peripheral muxing needs to be done.  However, if the pins get
routed through the GPIO PORTs pins, we need to make sure to request them
so that the muxing is properly set up.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-21 13:55:38 -05:00
Bartlomiej Zolnierkiewicz
509426bd46 pata_cmd64x: fix overclocking of UDMA0-2 modes
adev->dma_mode stores the transfer mode value not UDMA mode number
so the condition in cmd64x_set_dmamode() is always true and the higher
UDMA clock is always selected.  This can potentially result in data
corruption when UDMA33 device is used, when 40-wire cable is used or
when the error recovery code decides to lower the device speed down.

The issue was introduced in the commit 6a40da0 ("libata cmd64x: whack
into a shape that looks like the documentation") which goes back to
kernel 2.6.20.

Cc: stable@kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-20 15:42:12 -05:00
Jeff Garzik
06393afde3 Revert "pata_cmd64x: implement serialization as per notes"
This reverts commit d43744390e, because
it breaks the boot on several machines (mostly sparc64, at present).

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-20 15:39:55 -05:00
Linus Torvalds
70e66a5079 Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_mv: remove pointless NULL test
  pata_hpt3x2n: fix clock turnaround
  libata: fix reporting of drained bytes when clearing DRQ
  sata_mv: add power management support for the PCI controllers.
  sata_mv: store the board_idx into the host private data
  pata_octeon_cf: use resource_size(), to fix resource sizing bug
  libata: use the WRITE_SAME_16 define
  sata_mv: move the PCI bar description initialization code
  sata_mv: add power management support for the platform driver
  sata_mv: support clkdev framework
  sata_mv: increase PIO IORDY timeout

Fixed crazy mode-change in merge.
2009-12-19 11:04:29 -08:00
Jeff Garzik
0535f2bc17 sata_mv: remove pointless NULL test
Remove !ap test, where ap is guaranteed not-NULL.  Found by way of automated
bug report from Alexander Strakh via "Linux Device Drivers Verification
Project (Svace Detector)"

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:23:16 -05:00
Sergei Shtylyov
256ace9bbd pata_hpt3x2n: fix clock turnaround
The clock turnaround code still doesn't work for several reasons:

- 'USE_DPLL' flag in 'ap->host->private_data' is never initialized
  or updated, so the driver can only set the chip to the DPLL clock
  mode, not the PCI mode;

- the driver doesn't serialize access to the channels depending on
  the current clock mode like the vendor drivers, so the clock
  turnaround is only executed "optionally", not always as it should be;

- the wrong ports are written to when hpt3x2n_set_clock() is called
  for the secondary channel;

- hpt3x2n_set_clock() can inadvertently enable the disabled channels
  when resetting the channel state machines.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:11:27 -05:00
Robert Hancock
9a8fd68b15 libata: fix reporting of drained bytes when clearing DRQ
When we drain data from a device to clear DRQ during error recovery,
the number of bytes reported as drained is too low by a factor of 2
because the count is actually reporting the number of words drained,
not bytes. Fix this.

Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:08:29 -05:00
Saeed Bishara
b2dec48cca sata_mv: add power management support for the PCI controllers.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:06:11 -05:00
Saeed Bishara
1bfeff03f8 sata_mv: store the board_idx into the host private data
This information will be used in the resume function.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:05:00 -05:00
H Hartley Sweeten
4716eaf20f pata_octeon_cf: use resource_size(), to fix resource sizing bug
It appears the size for cs1 is calculated using the wrong resource.
Use the function resource_size to get the correct value.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:02:50 -05:00
Christoph Hellwig
0cdd6eb7e0 libata: use the WRITE_SAME_16 define
Now that the scsi tree has hit mainline we can use the newly added WRITE_SAME_16
define.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:02:09 -05:00
Saeed Bishara
c4bc7d7310 sata_mv: move the PCI bar description initialization code
The mv_init_host will be used to initialize the host hw on resume.
The PCI bar description need to be initialized only once when the
device probed.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:01:47 -05:00
Saeed Bishara
6481f2b52c sata_mv: add power management support for the platform driver
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 00:56:59 -05:00
Saeed Bishara
c77a2f4e6b sata_mv: support clkdev framework
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 00:56:46 -05:00
Saeed Bishara
d7b0c14369 sata_mv: increase PIO IORDY timeout
The old value (0xbc) in cycles of the IORDY timeout is suitable for
devices with core clock of 166 MHz, but some SoC controllers have
faster core clocks. The new value will make the IORDY timeout large
enough also for all SoC devices.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 00:56:36 -05:00
Linus Torvalds
09cea96caa Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
  powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
  MAINTAINERS: Add PowerPC patterns
  powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
  powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
  powerpc: Make "intspec" pointers in irq_host->xlate() const
  powerpc/8xx: DTLB Miss cleanup
  powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
  powerpc/8xx: Start using dcbX instructions in various copy routines
  powerpc/8xx: Restore _PAGE_WRITETHRU
  powerpc/8xx: Add missing Guarded setting in DTLB Error.
  powerpc/8xx: Fixup DAR from buggy dcbX instructions.
  powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
  powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
  powerpc/8xx: Invalidate non present TLBs
  powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
  pseries/pseries: Add code to online/offline CPUs of a DLPAR node
  powerpc: stop_this_cpu: remove the cpu from the online map.
  powerpc/pseries: Add kernel based CPU DLPAR handling
  sysfs/cpu: Add probe/release files
  powerpc/pseries: Kernel DLPAR Infrastructure
  ...
2009-12-12 14:27:24 -08:00
Linus Torvalds
4ef58d4e2a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
  tree-wide: fix misspelling of "definition" in comments
  reiserfs: fix misspelling of "journaled"
  doc: Fix a typo in slub.txt.
  inotify: remove superfluous return code check
  hdlc: spelling fix in find_pvc() comment
  doc: fix regulator docs cut-and-pasteism
  mtd: Fix comment in Kconfig
  doc: Fix IRQ chip docs
  tree-wide: fix assorted typos all over the place
  drivers/ata/libata-sff.c: comment spelling fixes
  fix typos/grammos in Documentation/edac.txt
  sysctl: add missing comments
  fs/debugfs/inode.c: fix comment typos
  sgivwfb: Make use of ARRAY_SIZE.
  sky2: fix sky2_link_down copy/paste comment error
  tree-wide: fix typos "couter" -> "counter"
  tree-wide: fix typos "offest" -> "offset"
  fix kerneldoc for set_irq_msi()
  spidev: fix double "of of" in comment
  comment typo fix: sybsystem -> subsystem
  ...
2009-12-09 19:43:33 -08:00
Linus Torvalds
382f51fe2f Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
  [SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
  [SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
  [SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
  [SCSI] zfcp: Update FSF error reporting
  [SCSI] zfcp: Improve ELS ADISC handling
  [SCSI] zfcp: Simplify handling of ct and els requests
  [SCSI] zfcp: Remove ZFCP_DID_MASK
  [SCSI] zfcp: Move WKA port to zfcp FC code
  [SCSI] zfcp: Use common code definitions for FC CT structs
  [SCSI] zfcp: Use common code definitions for FC ELS structs
  [SCSI] zfcp: Update FCP protocol related code
  [SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
  [SCSI] zfcp: Assign scheduled work to driver queue
  [SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
  [SCSI] zfcp: Implement module unloading
  [SCSI] zfcp: Merge trace code for fsf requests in one function
  [SCSI] zfcp: Access ports and units with container_of in sysfs code
  [SCSI] zfcp: Remove suspend callback
  [SCSI] zfcp: Remove global config_mutex
  [SCSI] zfcp: Replace local reference counting with common kref
  ...
2009-12-09 19:42:25 -08:00
Benjamin Herrenschmidt
bcd6acd51f Merge commit 'origin/master' into next
Conflicts:
	include/linux/kvm.h
2009-12-09 17:14:38 +11:00
Benjamin Herrenschmidt
88358ab089 libata/drivers: Add driver for Apple "MacIO" IDE controller
This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c

It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.

The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tejun Heo <tj@kernel.org>
2009-12-09 17:09:28 +11:00
Benjamin Herrenschmidt
f0353813af libata/sff: Use ops->bmdma_stop instead of ata_bmdma_stop()
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-09 17:09:27 +11:00
Linus Torvalds
23eb3b64b5 Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
  Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
  libata: Clarify ata_set_lba_range_entries function
  libata: Report zeroed read after TRIM and max discard size
  pata_hpt3x2n: fix overclocked MWDMA0 timing
  pata_it8213: MWDMA0 is unsupported
  [libata] MWDMA0 is unsupported on PIIX-like PATA controllers
  pata_via: clear UDMA transfer mode bit for PIO and MWDMA
  pata_sis: Power Management fix
  pata_rz1000: Power Management fix
  pata_radisys: fix UDMA handling
  pata_ns87415: Power Management fix
  pata_marvell: fix marvell_pre_reset() documentation
  pata_legacy: add pointers to QDI65x0 documentation
  pata_legacy: fix access to control register for QDI6580
  pata_legacy: fix QDI6580DP support
  pata_it8213: fix it8213_pre_reset() documentation
  pata_it8213: fix wrong MWDMA timings being programmed
  pata_it8213: fix PIO2 underclocking
  pata_it8213: fix wrong PIO timings being programmed
  pata_it8213: fix UDMA handling
  ...
2009-12-08 08:18:01 -08:00
Jiri Kosina
d014d04386 Merge branch 'for-next' into for-linus
Conflicts:

	kernel/irq/chip.c
2009-12-07 18:36:35 +01:00
Jeff Garzik
1b52f2a41c Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
This reverts commit f20941f334.

Sergei Shtylyov notes "You call min() on uncomparables [in
mwdma_clip_to_pio()], i.e. mwdma_to_pio[] contains XFER_PIO_* and
adev->pio_mode - XFER_PIO_0 yields you a mode number.  Thus the second
argument will always "win" as a minimal one"

Bartlomiej Zolnierkiewicz adds "There are more issues with the patch related
to mwdma_clip_to_pio().  The function can return values between 0 and
4 which obviously won't work well for the new code below for values
>2 (i.e. resulting in out-of-bounds array access for the common-case
of dev->pio_mode == XFER_PIO_4)."

Bartlomiej Zolnierkiewicz also notes the patch is incomplete, failing to
update MWDMA mode masks.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-07 11:41:25 -05:00
Linus Torvalds
d9b2c4d0b0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (50 commits)
  pcmcia: rework the irq_req_t typedef
  pcmcia: remove deprecated handle_to_dev() macro
  pcmcia: pcmcia_request_window() doesn't need a pointer to a pointer
  pcmcia: remove unused "window_t" typedef
  pcmcia: move some window-related code to pcmcia_ioctl.c
  pcmcia: Change window_handle_t logic to unsigned long
  pcmcia: Pass struct pcmcia_socket to pcmcia_get_mem_page()
  pcmcia: Pass struct pcmcia_device to pcmcia_map_mem_page()
  pcmcia: Pass struct pcmcia_device to pcmcia_release_window()
  drivers/pcmcia: remove unnecessary kzalloc
  pcmcia: correct handling for Zoomed Video registers in topic.h
  pcmcia: fix printk formats
  pcmcia: autoload module pcmcia
  pcmcia/staging: update comedi drivers
  PCMCIA: stop duplicating pci_irq in soc_pcmcia_socket
  PCMCIA: ss: allow PCI IRQs > 255
  PCMCIA: soc_common: remove 'dev' member from soc_pcmcia_socket
  PCMCIA: soc_common: constify soc_pcmcia_socket ops member
  PCMCIA: sa1111: remove duplicated initializers
  PCMCIA: sa1111: wrap soc_pcmcia_socket to contain sa1111 specific data
  ...
2009-12-05 09:42:59 -08:00
Mike Christie
e881a172da [SCSI] modify change_queue_depth to take in reason why it is being called
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.

This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>

[Vasu.Dev: v2
	Also converted pmcraid_change_queue_depth and then verified
all modules compile  using "make allmodconfig" for any new build
warnings on X86_64.

	Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-12-04 12:00:41 -06:00
André Goddard Rosa
af901ca181 tree-wide: fix assorted typos all over the place
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:55 +01:00
Krzysztof Halasa
972b94ffb9 drivers/ata/libata-sff.c: comment spelling fixes
Comment spelling fixes and whitespace adjustment.

Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:54 +01:00
Martin K. Petersen
d0634c4aea libata: Clarify ata_set_lba_range_entries function
ata_set_lba_range_entries used the variable max for two different things
which was confusing.  Make the function take a buffer size in bytes as
argument and return the used buffer size upon completion.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 18:01:23 -05:00
Martin K. Petersen
e78db4dfb1 libata: Report zeroed read after TRIM and max discard size
Our current TRIM payload is a single sector that can accommodate 64 *
65535 blocks being unmapped.  Report this value in the Block Limits
Maximum Unmap LBA count field.

If a storage device supports TRIM and the DRAT and RZAT bits are set,
report TPRZ=1 in Read Capacity(16).

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 18:01:04 -05:00
Bartlomiej Zolnierkiewicz
d413ff3e2a pata_hpt3x2n: fix overclocked MWDMA0 timing
Remove superfluous timings table entry while at it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 17:55:20 -05:00
Bartlomiej Zolnierkiewicz
fd87e792ad pata_it8213: MWDMA0 is unsupported
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 17:53:27 -05:00
Bartlomiej Zolnierkiewicz
82563232c7 [libata] MWDMA0 is unsupported on PIIX-like PATA controllers
MWDMA0 timings cannot be met with the PIIX based controller
programming interface.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 17:52:16 -05:00
Bartlomiej Zolnierkiewicz
c4d8a20022 pata_via: clear UDMA transfer mode bit for PIO and MWDMA
Fix register naming while at it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:13:39 -05:00
Bartlomiej Zolnierkiewicz
750c7136ea pata_sis: Power Management fix
Call sis_fixup() on resume.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:12:49 -05:00
Bartlomiej Zolnierkiewicz
0826ef5f6f pata_rz1000: Power Management fix
Fix ->resume method to re-enable & re-init PCI device properly
before doing chipset specific setup.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:12:35 -05:00
Bartlomiej Zolnierkiewicz
dd4a43c979 pata_radisys: fix UDMA handling
Set correct bits to switch between UDMA2 and UDMA4.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:11:24 -05:00
Bartlomiej Zolnierkiewicz
a809c68752 pata_ns87415: Power Management fix
Fix ->resume method to do chipset specific setup.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:08:30 -05:00
Bartlomiej Zolnierkiewicz
2a2beac928 pata_marvell: fix marvell_pre_reset() documentation
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:07:12 -05:00
Bartlomiej Zolnierkiewicz
9c7e0d22c5 pata_legacy: add pointers to QDI65x0 documentation
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:06:47 -05:00
Bartlomiej Zolnierkiewicz
6809e7301f pata_legacy: fix access to control register for QDI6580
We need to mask out the port offset from the port number
cached in ld_qdi->timing.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:06:14 -05:00
Bartlomiej Zolnierkiewicz
43c7d17ee7 pata_legacy: fix QDI6580DP support
Dual port QDI6580 has shared PIO timings for master/slave
devices so it needs to use custom ->qc_issue method.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:06:00 -05:00
Bartlomiej Zolnierkiewicz
13a28c15dd pata_it8213: fix it8213_pre_reset() documentation
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:02:12 -05:00
Bartlomiej Zolnierkiewicz
e3f1d5cd11 pata_it8213: fix wrong MWDMA timings being programmed
Clear old MWDMA timings before programming new ones (IT8213
is a single port host so there is no need to check ap->port_no).

This change should be safe as this is how we have been doing
things in IDE it8213 host driver for years.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:01:39 -05:00
Bartlomiej Zolnierkiewicz
ed869ff0c7 pata_it8213: fix PIO2 underclocking
[ port of Sergei's fixes for pata_efar from commit 5f33b3b ]

Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:01:13 -05:00
Bartlomiej Zolnierkiewicz
088ccb53a3 pata_it8213: fix wrong PIO timings being programmed
* do not clear PIO timings for master when programming slave
* program new PIO timings in the correct register nibble

Both changes should be safe as this is how we have been doing
things in IDE it8213 host driver for years.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 16:00:56 -05:00
Bartlomiej Zolnierkiewicz
e0ee792b75 pata_it8213: fix UDMA handling
Driver should program the cycle timing not the mode number
(doing the latter results in wrong timings being used).

There shouldn't be any problems with it as IDE it8213 host driver
has been doing it this way for years.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 15:59:25 -05:00
Bartlomiej Zolnierkiewicz
3915044468 pata_hpt3x3: Power Management fix
Fix ->resume method to re-enable & re-init PCI device properly
before doing chipset specific setup.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 15:58:53 -05:00
Bartlomiej Zolnierkiewicz
940a68de56 pata_cs5520: remove dead VDMA support
It has been dead for the last three years (== since the initial driver
merge) and probability that it will ever get fixed is quite low.

Since there is no reason to keep this dead code around any longer just
remove it (it can still be retrieved from the git history if necessary).

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 15:52:51 -05:00
Bartlomiej Zolnierkiewicz
dd221f9ce9 pata_efar: fix wrong MWDMA timings being programmed
Do not clear MWDMA timings for device on the other port when
programming slave device.

This change should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 15:50:51 -05:00
Bartlomiej Zolnierkiewicz
f79ff92649 pata_efar: fix wrong PIO timings being programmed
* do not clear PIO timings for master when programming slave
* do not clear PIO timings for device on the other port when
  programming slave device

Both changes should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 15:50:31 -05:00
Bartlomiej Zolnierkiewicz
6938594374 ata_piix: fix MWDMA handling on PIIX3
Fix erroneous check for ap->udma_mask in do_pata_set_dmamode()
resulting in controller not being programmed properly for MWDMA.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 15:44:31 -05:00
Mark Nelson
7a02267e0f ahci: let users know that Promise PDC42819 support is limited to SATA devices
ahci can drive the Promise PDC42819, but obviously it can only use SATA
disks connected to this controller. The controller can actually support
SAS disks as well, but we only know how to use it in it's AHCI mode.

Add a message to let users know that because ahci is driving their chip
they can only use the SATA disks connected to this controller.

Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 14:36:17 -05:00
Sergei Shtylyov
89d3b3603b ata: use pci_dev->revision
Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
they weren't converted by commit 44c10138fd
(PCI: Change all drivers to use pci_device->revision).

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 14:36:17 -05:00
Sergei Shtylyov
82beb5d894 pata_hpt366: fix timing register documentation
The comment in the driver actually describes HPT37x's timing register layout,
which is different from HPT36x.  Fix it and reformat the comment, while at it.

Bump the driver version, accounting for several patches that forgot to do it.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 14:36:17 -05:00
Bartlomiej Zolnierkiewicz
9cd13bdbae libata: add comment documenting PIO latency issues on UP
Based on:
http://lkml.indiana.edu/hypermail/linux/kernel/0908.2/01420.html

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 14:36:16 -05:00
Sergei Shtylyov
5600c70e57 pata_hpt{37x|3x2n}: fix timing register masks (take 2)
These drivers inherited from the older 'hpt366' IDE driver the buggy timing
register masks in their set_piomode() metods. As a result, too low command
cycle active time is programmed for slow PIO modes.  Quite fortunately, it's
later "fixed up" by the set_dmamode() methods which also "helpfully" reprogram
the command timings, usually to PIO mode 4; unfortunately, setting an UltraDMA
mode #N also reprograms already set PIO data timings, usually to MWDMA mode #
max(N, 2) timings...

However, the drivers added some breakage of their own too:  the bit that they
set/clear to control the FIFO is sometimes wrong -- it's actually the MSB of
the command cycle setup time; also, setting it in DMA mode is wrong as this
bit is only for PIO actually and clearing it for PIO modes is not needed as
no mode in any timing table has it set...

Fix all this, inverting the masks while at it, like in the 'hpt366' and
'pata_hpt366' drivers; bump the drivers' versions, accounting for recent
patches that forgot to do it...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 14:36:16 -05:00
Alan Cox
8e182a90f9 pata_piccolo: Driver for old Toshiba chipsets
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.

As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 14:35:31 -05:00
Alan Cox
d6250a03fa pata_ali: Fix regression with old devices
Making the new stuff work broke some of the old chipsets. We need to go
back to the old set up values for these it seems. Unfortunately even with
documentation this is basically a mix of cargoculting and guesswork.

Chased down to the exact line by Gianluca.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:36 -05:00
Alan Cox
be315d4615 [libata] PATA: Update experimental tags
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:36 -05:00
Alan Cox
d43744390e pata_cmd64x: implement serialization as per notes
Daniela Engert pointed out that there are some implementation notes for the
643 and 646 that deal with certain serialization rules. In theory we don't
need them because they apply when the motherboard decides not to retry PCI
requests for long enough and the chip is busy doing a DMA transfer on the
other channel.

The rule basically is "don't touch the taskfile of the other channel while
a DMA is in progress". To implement that we need to

- not issue a command on a channel when there is a DMA command queued
- not issue a DMA command on a channel when there are PIO commands queued
- use the alternative access to the interrupt source so that we do not
  touch altstatus or status on shared IRQ.

Updated to remote extra conditional check Bartlomiej noted and to remove
the variables for irq checks as the CMD648 doesn't have the underlying problem.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:36 -05:00
Alan Cox
f20941f334 pata_sis: Implement MWDMA for the UDMA 133 capable chips
Bartlomiej pointed out that while this got fixed in the old driver whoever
did it didn't port it across.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:36 -05:00
Alan Cox
10734fc8d5 pata_via: Blacklist some combinations of Transcend Flash and via
Reported by Mikulas Patocka.

VIA VT82C586B + Transcend TS64GSSD25-M v0826 does not work in UDMA mode

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:36 -05:00
Benjamin Herrenschmidt
294264a942 libata/sff: Use ops->bmdma_stop instead of ata_bmdma_stop()
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:36 -05:00
Christoph Hellwig
18f0f97850 libata: add translation for SCSI WRITE SAME (aka TRIM support)
Add support for the ATA TRIM command in libata.  We translate a WRITE SAME 16
command with the unmap bit set into an ATA TRIM command and export enough
information in READ CAPACITY 16 and the block limits EVPD page so that the new
SCSI layer discard support will driver this for us.

Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce
the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is
merged we can fix it up to properly use the symbolic name.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
Tejun Heo
6013efd886 libata: retry failed FLUSH if device didn't fail it
If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.

However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.

This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination.  Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode.  This was reported in the following bugzilla bug.

  http://bugzilla.kernel.org/show_bug.cgi?id=14543

This patch makes libata EH retry FLUSH if it wasn't failed by the
device.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
ashish kalra
fd6c29e3de sata_fsl: Add asynchronous notification support
Enable device hot-plug support on Port multiplier fan-out ports

Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
Bartlomiej Zolnierkiewicz
10a9c96922 pata_hpt{37x,3x2n}: add debounce delay to cable detection methods
Alan Cox reported that cable detection sometimes works unreliably
for HPT3xxN and that the issue is fixed by adding debounce delay
as used by the vendor driver.

Sergei Shtylyov also noticed that debounce delay is needed for all
HPT37x and HPT3xxN chipsets according to vendor drivers.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
Bartlomiej Zolnierkiewicz
f3b1cf40d4 pata_hpt3x2n: fix cable detection
The detection was reversed between primary and secondary ports.

Fix it to match hpt366 and the vendor driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
Matthew Garrett
6a74463798 ata: Don't require newlines for link_power_management_policy
sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
Otavio Salvador
4192be6402 pata-it821x: use PCI_DEVICE_ID_RDC_D1010 define
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
Bartlomiej Zolnierkiewicz
ab81a505ae pata_hpt37x: unify ->pre_reset methods
We can use the same ->pre_reset method for all HPT37x chipsets now.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:34 -05:00
Bartlomiej Zolnierkiewicz
9e87be9edd pata_hpt37x: add proper cable detection methods
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:34 -05:00
Shaohua Li
1b677afda4 ahci: disable SNotification capability for ich8
I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.

It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.

PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:34 -05:00
Vivek Mahajan
dae77214fa sata_sil24: MSI support, disabled by default
The following patch adds MSI support. Some platforms
may have broken MSI, so those are defaulted to use
legacy PCI interrupts.

Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:34 -05:00
Robert Hancock
097dac9183 libata: remove experimental tag on PATA drivers
Remove the experimental tag on Parallel ATA drivers. Though some of the
individual PATA drivers are still marked as experimental, as a group they can
hardly be considered to be, given they've been used in various distros for some
time.

Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:34 -05:00
Thiago Farina
4c4a90fd2b sata_mv: Clean up hard coded array size calculation.
Use ARRAY_SIZE macro of kernel api instead.

Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:34 -05:00
Jiri Slaby
7095e3eb49 pata_via: fix double put on isa bridge
In via_init_one, when via_isa_bridges iterator reaches
PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is
found but rev doesn't match, pci_dev_put(isa) is called twice.

Do pci_dev_put only once.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:34 -05:00
Krzysztof Halasa
ba3a221ce2 pata_cs5536: use 32-bit BM DMA template instead of 16-bit.
Tested on IXP425 + CS5536.

Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:34 -05:00
Tejun Heo
f2406770a2 libata-acpi: missing _SDD is not an error
Missing _SDD is not an error.  Don't treat it as one.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:33 -05:00
Dominik Brodowski
5fa9167a1b pcmcia: rework the irq_req_t typedef
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:

(1) IRQInfo2 was unused in any case, so drop it.

(2) IRQInfo1 was used write-only, so drop it.

(3) Instance (private data to be passed to the IRQ handler):
	Most PCMCIA drivers using pcmcia_request_irq() to actually
	register an IRQ handler set the "dev_id" to the same pointer
	as the "priv" pointer in struct pcmcia_device. Modify the two
	exceptions (ipwireless, ibmtr_cs) to also work this waym and
	set the IRQ handler's "dev_id" to p_dev->priv unconditionally.

(4) Handler is to be of type irq_handler_t.

(5) Handler != NULL already tells whether an IRQ handler is present.
	Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
	irq_req_t.Attributes.

CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2009-11-28 18:03:14 +01:00
Jiang Yutang
a0a74d1ee2 sata_fsl: Split hard and soft reset
Split sata_fsl_softreset() into hard and soft resets to make
error-handling more efficient & device and PMP detection more
reliable.

Also includes fix for PMP support, driver tested with Sil3726,
Sil4726 & Exar PMP controllers.

[AV: Also fixes resuming from deep sleep on MPC8315 CPUs]

Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-11-19 18:18:17 -05:00
Otavio Salvador
d914e5b703 pata_cs5535: fix comment header typo
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-11-09 09:40:55 +01:00
Dominik Brodowski
444486a5f9 pcmcia: use dynamic debug infrastructure, deprecate CS_CHECK (ide)
ide-cs.c is the only PCMCIA device driver making use of CONFIG_PCMCIA_DEBUG,
so convert it to use the dynamic debug infrastructure.

Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.

CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2009-11-08 18:23:14 +01:00
JosephChan@via.com.tw
f38e35b43f sata_via: Remove redundant device ID for VIA VT8261
Just remove redundant device ID for VIA VT8261.
The device ID 0x9000 and 0x9040 are redundant (for VT8261).
The 0x9040 is reserved for other usage.

Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-11-03 14:27:06 -05:00
Julia Lawall
a1104016ce drivers/ata/libata: Move dereference after NULL test
In each case, if the NULL test on qc is needed, then the derefernce
should be after the NULL test.

A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):

// <smpl>
@match exists@
expression x, E;
identifier fld;
@@

* x->fld
  ... when != \(x = E\|&x\)
* x == NULL
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-11-03 14:26:12 -05:00
Mark Nelson
e65cc194f7 ahci: Enable SB600 64bit DMA on MSI K9A2 Platinum v2
Like the Asus M2A-VM, MSI's K9A2 Platinum (MS-7376) can also support 64bit
DMA. It is a new enough board that all the BIOS releases work correctly with
64bit DMA enabled.

Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-11-03 14:25:57 -05:00
Gwendal Grignou
159a7ff7a1 sata_mv: Prevent PIO commands to be defered too long if traffic in progress.
Use excl_link when non NCQ commands are defered, to be sure they are processed
as soon as outstanding commands are completed. It prevents some commands to be
defered indifinitely when using a port multiplier.

Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-16 06:22:46 -04:00
Alan Cox
6d4f950e9e pata_sc1200: Fix crash on boot
The SC1200 needs a NULL terminator or it may cause a crash on boot.

Bug #14227

Also correct a bogus comment as the driver had serializing added so can run
dual port.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-16 06:22:40 -04:00
Tejun Heo
f4b31db92d libata: fix internal command failure handling
When an internal command fails, it should be failed directly without
invoking EH.  In the original implemetation, this was accomplished by
letting internal command bypass failure handling in ata_qc_complete().
However, later changes added post-successful-completion handling to
that code path and the success path is no longer adequate as internal
command failure path.  One of the visible problems is that internal
command failure due to timeout or other freeze conditions would
spuriously trigger WARN_ON_ONCE() in the success path.

This patch updates failure path such that internal command failure
handling is contained there.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-16 06:22:31 -04:00
Tejun Heo
4f7c287499 libata: fix PMP initialization
Commit 842faa6c1a fixed error handling
during attach by not committing detected device class to dev->class
while attaching a new device.  However, this change missed the PMP
class check in the configuration loop causing a new PMP device to go
through ata_dev_configure() as if it were an ATA or ATAPI device.

As PMP device doesn't have a regular IDENTIFY data, this makes
ata_dev_configure() tries to configure a PMP device using an invalid
data.  For the most part, it wasn't too harmful and went unnoticed but
this ends up clearing dev->flags which may have ATA_DFLAG_AN set by
sata_pmp_attach().  This means that SATA_PMP_FEAT_NOTIFY ends up being
disabled on PMPs and on PMPs which honor the flag breaks hotplug
support.

This problem was discovered and reported by Ethan Hsiao.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ethan Hsiao <ethanhsiao@jmicron.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-16 06:21:54 -04:00
Tejun Heo
6489e3262e sata_nv: make sure link is brough up online when skipping hardreset
prereset doesn't bring link online if hardreset is about to happen and
nv_hardreset() may skip if conditions are not right so softreset may
be entered with non-working link status if the system firmware didn't
bring it up before entering OS code which can happen during resume.
This patch makes nv_hardreset() to bring up the link if it's skipping
reset.

This bug was reported by frodone@gmail.com in the following bug entry.

  http://bugzilla.kernel.org/show_bug.cgi?id=14329

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: frodone@gmail.com
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-16 06:21:32 -04:00
Shane Huang
5deab53665 ahci / atiixp / pci quirks: rename AMD SB900 into Hudson-2
This patch renames the code name SB900 into Hudson-2

Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-16 06:21:20 -04:00
peer chen
726206f84c ahci: Add the AHCI controller Linux Device ID for NVIDIA chipsets.
Add the generic device ID for NVIDIA AHCI controller.

Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-16 06:20:00 -04:00
JosephChan@via.com.tw
7d948b1114 pata_via: extend the rev_max for VT6330
Fix the VT6330 issue, it's because the rev_max of VT6330 exceeds 0x2f.
The VT6415 and VT6330 share the same device ID.

Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-16 06:19:45 -04:00
Markus Trippelsdorf
8e5132175b ahci: Add ifdef wrapper to ahci_gtf_filter_workaround
Commit f80ae7e45a
ahci: filter FPDMA non-zero offset enable for Aspire 3810T
breaks the current git build for configurations that don't define
CONFIG_ATA_ACPI.
This adds an ifdef wrapper to ahci_gtf_filter_workaround.

Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-09 00:29:07 -04:00
Bartlomiej Zolnierkiewicz
7affb32a32 pata_atp867x: add Power Management support
Cc: Jung-Ik (John) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 20:58:23 -04:00
Bartlomiej Zolnierkiewicz
c59bcc37cb pata_atp867x: PIO support fixes
* use  8 clk setting for active clocks == 7 (was 12 clk)
* use 12 clk setting for active clocks > 12 (was  8 clk)
* do 66MHz bus fixup before mapping active clocks
* fix setup of PIO command timings

Acked-by: Jung-Ik (John) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 20:58:23 -04:00
John(Jung-Ik) Lee
64207f5913 pata_atp867x: clarifications in timings calculations and cable detection
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 20:58:22 -04:00
Bartlomiej Zolnierkiewicz
566b54c8a4 pata_atp867x: fix it to not claim MWDMA support
MWDMA modes are not supported by this driver currently.

Acked-by: Jung-Ik (John) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 20:58:21 -04:00
Tejun Heo
3b761d3d43 libata: fix incorrect link online check during probe
While trying to work around spurious detection retries for
non-existent devices on slave links, commit
816ab89782 incorrectly added link
offline check logic before ata_eh_thaw() was called.  This means that
if an occupied link goes down briefly at the time that offline check
was performed, device class will be cleared to ATA_DEV_NONE and libata
wouldn't retry thus failing detection of the device.

The offline check should be done after the port is thawed together
with online check so that such link glitches can be detected by the
interrupt handler and handled properly.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tim Blechmann <tim@klingt.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 20:58:18 -04:00
Tejun Heo
f80ae7e45a ahci: filter FPDMA non-zero offset enable for Aspire 3810T
Curiously, Aspire 3810T issues many SATA feature enable commands via
_GTF, of which one is invalid and another is not supported by the
drive.  In the process, it also enables FPDMA non-zero offset.
However, the feature also needs to be supported and enabled from the
controller and it's wrong to enable it from _GTF unless the controller
can do it by default.

Currently, this ends up enabling FPDMA non-zero offset only on the
drive side leading to NCQ command failures and eventual disabling of
NCQ.  This patch makes libata filter out FPDMA non-zero offset enable
for the machine.

This was reported by Marcus Meissner in bnc#522790.

  https://bugzilla.novell.com/show_bug.cgi?id=522790

Reported-by: Marcus Meissner <meissner@novell.com>

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 00:26:29 -04:00
Tejun Heo
110f66d25c libata: make gtf_filter per-dev
Add ->gtf_filter to ata_device and set it to ata_acpi_gtf_filter when
initializing ata_link.  This is to allow quirks which apply different
gtf filters.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 00:26:27 -04:00
Tejun Heo
fa5b561c4e libata: implement more acpi filtering options
Currently libata-acpi can only filter DIPM among SATA feature enables
via _GTF.  This patch adds the capability to filter out FPDMA non-zero
offset, in-order guarantee and auto-activation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 00:26:26 -04:00
Tejun Heo
f1bce7f80e libata: cosmetic updates
We're about to add more SATA_* and ATA_ACPI_FILTER_* constants.
Reformat them in preparation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 00:25:03 -04:00
Robert Hancock
4c521c8ef0 ahci: display all AHCI 1.3 HBA capability flags (v2)
Update the AHCI driver to display all of the HBA capabilities defined in the
AHCI 1.3 specification. Some of these are in a new CAP2 (HBA Capabilities
Extended) register which is only defined on AHCI 1.2 or later. The spec says
that undefined registers should always return 0 on read, but to be safe we
assume a value of 0 unless the controller reports AHCI version 1.2 or later.
The value can also be retrieved through sysfs as with the existing capability
field.

For example, on an Intel Ibex Peak (PCH) controller:

ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part ems
sxs apst

We don't do anything special with the new flags yet.

Also, change the code that displays the flags to use the same bit enumerations
that are used to control actual operation.

Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 00:23:03 -04:00
Dirk Hohndel
c21c8066be pata_ali: trivial fix of a very frequent spelling mistake
something-bility is spelled as something-blity
so a grep for 'blit' would find these lines

I broke this one out from the rest as it actually changes
the output of a kernel message - so it could in theory
change the behavior of tools that parse that ouput

Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 00:22:10 -04:00
Tejun Heo
2fcad9d271 ahci: disable 64bit DMA by default on SB600s
Till now only one board, ASUS M2A-VM, can do 64bit dma with recent
BIOSen.  Enabling 64bit DMA by default already broke three boards.
Enabling 64bit DMA isn't worth these regressions.  Disable 64bit DMA
by default and enable it only on boards which are known to work.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Gabriele Balducci <balducci@units.it>
Reported-by: maierp@informatik.tu-muenchen.de
Cc: Shane Huang <shane.huang@amd.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-10-06 00:21:42 -04:00
Krzysztof Halasa
ad452d64c6 trivial: fix comment typo in drivers/ata/pata_hpt37x.c
A comment fix in drivers/ata/pata_hpt37x.c.

Signed-off-by: Krzysztof Ha³asa <khc@pm.waw.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-09-21 15:15:53 +02:00
John(Jung-Ik) Lee
d15d6e6cc3 libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.

Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Reviewed-by:  Grant Grundler <grundler@google.com>
Reviewed-by:  Gwendal Gringo <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-17 16:47:06 -04:00
Robert Hancock
90950a2504 pata_amd: do not filter out valid modes in nv_mode_filter
On a Compaq Presario V3000 laptop (NVIDIA MCP51 chipset), pata_amd selects
PIO0 mode for the PATA DVD-RAM drive instead of MWDMA2 which it supports:

ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x7001->0x1, BIOS=0x0 (0x0) ACPI=0x7001 (60:600:0x11)
ata4.00: configured for PIO0

For some reason, the BIOS-set UDMA configuration returns 0 and the ACPI _GTM
reports that UDMA2 and PIO0 are enabled. This causes nv_mode_filter to end up
allowing only PIO0 and UDMA0-2. Since the drive doesn't support UDMA we end up
using PIO0.

Since the controllers should always support PIO4, MWDMA2 and UDMA2 regardless
of what cable type is used, let's make sure we don't filter out these modes
regardless of what wacky settings the BIOS is using.

Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-17 16:46:41 -04:00
Mikael Pettersson
ff7cddf59e sata_promise: update reset code
sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.

This patch thus updates the reset code to more closely
match the reference driver:

- soft reset (pdc_reset_port):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * write reset bit in PDC_CTLSTAT before the first read
    in the loop
  * for 2nd gen SATA follow up with FPDMA reset and clearing
    error status registers
- hard reset (pdc_sata_hardreset):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * reset ATA engine via the PCI control register
  * Tejun's change to use non-waiting hardreset + follow-up SRST

I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).

Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-17 16:46:34 -04:00
Mikael Pettersson
0ae6654da4 sata_promise: disable hotplug on 1st gen chips
1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.

The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.

Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-17 16:46:12 -04:00
Tejun Heo
4dc738ed2a libata: fix spurious WARN_ON_ONCE() on port freeze
Commit 54c38444fa makes libata abort qcs
after the port is frozen.  This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error.  However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously.  Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-17 16:45:40 -04:00