Add an au0828 module option that allows a user to override the USB speed check.
Intended for advanced users who understand the consequences of trying to use
the device with a 12Mbps bus.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an em28xx module option that allows a user to override the USB speed check.
Intended for advanced users who understand the consequences of trying to use
the device with a 12Mbps bus.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some remaining dead code. Warning showed up in Hans
Verkuil's daily report after I committed hg changeset 7f2eea75118b.
Thanks to Michael Krufky for bringing the warning to my attention.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the KWorld 2800d work properly. In this case, that means making the
profile more generic so that it works for both the Pointnix Intra-Oral USB
camera and the KWorld device.
The device provides the audio through a pass-thru cable, so we don't need
an actual audio capture profile (neither the K-World device nor the Pointnix
have an onboard audio decoder).
Thanks to Paul Thomas for providing sample hardware.
Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au0828 basically just doesn't work at 12 Mbps. The isoc pipe needs
nearly 200 Mbps for analog support, so users would see garbage video, and on
the DVB/ATSC side scanning is likely to work but if the user tried to tune it
would certainly appear to have failed.
It's better to fail explicity up front and tell the user to plug into a USB 2.0
port, than to let the driver load and the user have weird problems with tuning
and garbage video.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx basically just doesn't work at 12 Mbps. The isoc pipe needs
nearly 200 Mbps for analog support, so users would see garbage video, and on
the DVB/ATSC side scanning is likely to work but if the user tried to tune it
would certainly appear to have failed.
It's better to fail explicity up front and tell the user to plug into a USB 2.0
port, than to let the driver load and the user have weird problems with tuning
and garbage video.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both ATSC and DVB @ 6MHz bandwidth require the same offset.
While we're fixing it, let's cleanup the bandwidth setup to better
reflect the fact that it is a function of the bandwidth.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only two countries that are known to use 6MHz bandwidth are Taiwan
and Uruguay. Both use QAM subcarriers at OFTM.
This patch fixes the firmware load for such countries, where the
required firmware is the QAM one.
This also confirms the previous tests where it was noticed that the 6MHz
QAM firmware doesn't work for cable. So, this patch also removes support
for DVB-C, instead of just printing a warning.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing this issue and
to Andy Walls <awalls@radix.net> for an initial patch for this fix.
Cc: Terry Wu <terrywu2009@gmail.com>
Acked-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID (0458:4012) for Genius TVGo DVB-T03.
Thanks to Petr Vodicka <vodicka.petr@email.cz> for reporting and testing.
Tested-by: Petr Vodicka <vodicka.petr@email.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to David Ward and Mike Krufky for reporting the problem and
debugging this as an unresolved symbol due to a 64 bit divide on a 32 bit
system. David Ward provided the content of this patch; Andy Walls only
performed some cosmetic edits.
Reported-by: David Ward <david.ward@gatech.edu>
Signed-off-by: David Ward <david.ward@gatech.edu>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Test Code: (Provided by Douglas)
v4l-dvb/v4l2-apps/test/stress-buffer.c
The audio DMA area was never being freed and would slowly leak over
time as the v4l device was opened and closed by an application.
Thanks again to Douglas for generating the test code to help locate
memory leaks!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove always false if over unsigned int variable
Signed-off-by: Filipe Rosset <rosset.filipe@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a kconfig symbol that allows someone to disable all
multimedia config options at one time.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add cx23885 support for card "Mygica X8506 DMB-TH".
It should work on "Magic-Pro ProHDTV Extreme" as well, as they are
same hardware with different branding.
Sign-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enables analog/digital tv, radio and remote control (gpio).
Tested-by: Marcin Wojcikowski <emtees.mts@gmail.com>
Tested-by: Karel Juhanak <karel.juhanak@warnet.cz>
Tested-by: Andrew Goff <goffa72@gmail.com>
Tested-by: Jan Novak <novak-j@seznam.cz>
Signed-off-by: Miroslav Sustek <sustmidown@centrum.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Extend the gain range
- Adjust the exposure
- Remove the broken autogain
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The YUYV 640x480 format did not work with ov965x.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the burst gate delays to use a crystal value of 28636360 as assumed by
the rest of the driver. Also have the initial color sub-carrier freq paramter
use the src decimation ratio per the documentation, instead of the actual
crystal/pixel clock ratio. The tracking circuit will find the correct color
subcarrier in any case, as long as we're close. Also fix up some debug print
statements.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Finish changes for sliced and raw VBI for 625 line systems. Tested with VPS
and WSS being emitted by a PVR-350 in field 1 lines 16 and 23.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial changes to get sliced VBI for 625 line system working. This is patch
is untested.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c quirk in the saa7134_i2c_xfer function does a bogus write
to i2c address 0xfd, to work around a bug in the silicon that
affects read transactions.
Unfortunately, this hack is not working properly, since the bogus
write is to 0xfd, an invalid i2c address. Fix this quirk by using
an actual valid i2c address, 0xfe, which is still unlikely to be
used as an i2c address for any actual i2c client.
This is required in order to properly communicate with a TDA10048
DVB-T demod located at i2c address 0x10 on the primary i2c bus.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steve missed the HVR1210 config struct for the TDA10048 in his IF freq patch.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was causing a lock failure in Australia.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Ensure we specify I/F's for all bandwidths
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx23885: Ensure we specify I/F's for all bandwidths
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The variable minor have assigned value twice, the first time is in the
initial "video_device" data struct in those drivers, pls see
saa7134-video.c,line 2503.
---
Signed-off-by: Figo.zhang <figo.zhang@kolorific.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the ir-kbd-i2c driver has been converted to a new-style i2c
driver, we can instantiate the ir_video I2C device by default. The
pvr2_disable_ir_video is kept to disable the IR receiver, either
because the user doesn't use it, or for debugging purpose.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Probe I2C addresses 0x71 and 0x6b for IR receiver devices (for the
PVR150 and Adaptec cards, respectively.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we instantiate I2C IR devices explicitly, we can skip probing
altogether on boards where the I2C IR device address is known. The
AVerMedia Cardbus E506R is one of these boards.
Tested-by: Oldrich Jedlicka <oldium.pro@seznam.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we instantiate I2C IR devices explicitly, we can skip probing
altogether on boards where the I2C IR device address is known. The MSI
TV@nywhere Plus is one of these boards.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code in ir_probe makes the dangerous assumption that all IR
receivers are supported by the driver. The new i2c model makes it
possible for bridge drivers to instantiate IR devices before they are
supported, therefore the ir-kbd-i2c drivers must be made more robust
to not spam the logs or even crash on unsupported IR devices. Simply,
the driver will not bind to the unsupported devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For specific boards, pass initialization data to ir-kbd-i2c instead
of modifying the settings after the device is initialized. This is
more efficient and easier to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the standard device driver binding model, the name field of
struct i2c_client is used to match devices to their drivers, so we
must stop using it for internal purposes. Define a separate field
in struct IR_i2c as a replacement, and use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
radio-mr800.c uses struct mutex, so while <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it already includes, the right
thing is to include it directly.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dvb_dvr_read may unlock the dmxdev mutex and return -ENODEV, except this
function is a file op and will never be called with the mutex held.
There's existing mutex_lock and mutex_unlock around the actual read but
it's commented out. These should probably be uncommented but the read
blocks and this could block another non-blocking reader on the mutex
instead.
This change comments out the extra mutex_unlock.
[akpm@linux-foundation.org: cleanups, simplification]
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change kmalloc()/kfree() to vmalloc()/vfree() for sglist allocation
during videobuf_dma_map() and videobuf_dma_unmap()
High resolution sensors might require too many contiguous pages
to be allocated for sglist by kmalloc() during videobuf_dma_map()
(i.e. 256Kib for 8MP sensor).
In such situations, kmalloc() could face some problem to find the
required free memory. vmalloc() is a safer solution instead, as the
allocated memory does not need to be contiguous.
Signed-off-by: David Cohen <david.cohen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
