According to Documentation/dmaengine.txt, scatterlists must be mapped
using the DMA struct device.
However, "dma_chan.dev->device" is the sysfs class device's device.
Use "dma_chan.device->dev" instead, which is the real DMA device's device.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to Documentation/DMA-API.txt, dma_map_sg() returns 0 on failure.
As spi_map_buf() returns an error code, convert zero into -ENOMEM.
Keep the existing check for negative numbers just in case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Olof Johansson pointed out that usually the company name is picked as
namespace prefix to specific properties. So expect "energymicro,location"
but fall back to the previously introduced name "efm32,location".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Xilinx SPI driver initializes the bus_num field of the SPI master to
pdev->dev.id. pdev->dev.id is always 0 for platform devices which causes bus
number conflicts for the SPI controller when creating multiple device instances
of the driver. Instead use pdev->id which will have the assignt platform device
id. If the device is instantiated via devicetree pdev->id is -1 which will cause
the SPI core to dynamically assign a id (or use the id defined via a alias in
the devicetree).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As of commit ab116a4df4 ("dmaengine:
shdma: fix a build failure on platforms with no DMA support"), the DMA
filter function shdma_chan_filter() is sufficiently abstracted to allow
building without DMA support. Hence drop the SH_DMAE_BASE dependency on
SUPERH.
Also increase build coverage by allowing the driver to be enabled if
COMPILE_TEST=y.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If NO_DMA=y:
drivers/built-in.o: In function `sh_msiof_release_dma':
spi-sh-msiof.c:(.text+0x23cbfe): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_msiof_request_dma':
spi-sh-msiof.c:(.text+0x23cd5e): undefined reference to `dma_map_single'
spi-sh-msiof.c:(.text+0x23cd70): undefined reference to `dma_mapping_error'
spi-sh-msiof.c:(.text+0x23cdca): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_msiof_dma_once':
spi-sh-msiof.c:(.text+0x23d450): undefined reference to `dma_sync_single_for_cpu'
spi-sh-msiof.c:(.text+0x23d5ea): undefined reference to `dma_sync_single_for_cpu'
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes s5p64x0 related spi because of no more support for
s5p64x0 SoCs. Meanwhile, cleanup SPI DT bindings for s5p6440-spi, it
should be s5p64x0-spi instead.
Cc: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
rspi_release_dma() doesn't need access to any fields in the driver private
data, except for the pointer to the SPI master object. Hence just pass the
needed pointer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduced by commit 8b983e90ea ("spi: rspi:
Extract rspi_common_transfer()"), which removed its users.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch introduces the use of devm_ioremap and removes the iounmaps
in the probe and remove functions. Also, the labels are renamed to
preserve ordering.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Without the dependencies for the accessors the driver can be enabled on
architectures where it will fail to build.
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes a bug on the deallocation of memory allocated using
request_mem_region, by using release_mem_region instead of
release_resource and kfree.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to facilitate understanding, rockchip SPI controller IP design
looks similar in its registers to designware. But IC implementation
is different from designware, So we need a dedicated driver for Rockchip
RK3XXX SoCs integrated SPI. The main differences:
- dma request line: rockchip SPI controller have two DMA request line
for tx and rx.
- Register offset:
RK3288 dw
SPI_CTRLR0 0x0000 0x0000
SPI_CTRLR1 0x0004 0x0004
SPI_SSIENR 0x0008 0x0008
SPI_MWCR NONE 0x000c
SPI_SER 0x000c 0x0010
SPI_BAUDR 0x0010 0x0014
SPI_TXFTLR 0x0014 0x0018
SPI_RXFTLR 0x0018 0x001c
SPI_TXFLR 0x001c 0x0020
SPI_RXFLR 0x0020 0x0024
SPI_SR 0x0024 0x0028
SPI_IPR 0x0028 NONE
SPI_IMR 0x002c 0x002c
SPI_ISR 0x0030 0x0030
SPI_RISR 0x0034 0x0034
SPI_TXOICR NONE 0x0038
SPI_RXOICR NONE 0x003c
SPI_RXUICR NONE 0x0040
SPI_MSTICR NONE 0x0044
SPI_ICR 0x0038 0x0048
SPI_DMACR 0x003c 0x004c
SPI_DMATDLR 0x0040 0x0050
SPI_DMARDLR 0x0044 0x0054
SPI_TXDR 0x0400 NONE
SPI_RXDR 0x0800 NONE
SPI_IDR NONE 0x0058
SPI_VERSION NONE 0x005c
SPI_DR NONE 0x0060
- register configuration:
such as SPI_CTRLRO in rockchip SPI controller:
cr0 = (CR0_BHT_8BIT << CR0_BHT_OFFSET)
| (CR0_SSD_ONE << CR0_SSD_OFFSET);
cr0 |= (rs->n_bytes << CR0_DFS_OFFSET);
cr0 |= ((rs->mode & 0x3) << CR0_SCPH_OFFSET);
cr0 |= (rs->tmode << CR0_XFM_OFFSET);
cr0 |= (rs->type << CR0_FRF_OFFSET);
For more information, see RK3288 chip manual.
- Wait for idle: Must ensure that the FIFO data has been sent out
before the next transfer.
Signed-off-by: addy ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit id 2bd16e3e23
(spi: omap2-mcspi: Do not configure the controller
on each transfer unless needed) does its job too
well so omap2_mcspi_setup_transfer() isn't called
even when an SPI slave driver changes 'spi->mode'.
The result is that the mode requested by the SPI
slave driver never takes effect.
Fix this by adding the 'mode' member to the
omap2_mcspi_cs structure which holds the mode
value that the hardware is configured for.
When the SPI slave driver changes 'spi->mode'
it will be different than the value of this new
member and the SPI master driver will know that
the hardware must be reconfigured (by calling
omap2_mcspi_setup_transfer()).
Fixes: 2bd16e3e23 (spi: omap2-mcspi: Do not configure the controller on each transfer unless needed)
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
ret is unused when CONFIG_FSL_SOC defined,
so return ret instead of -ENOMEM when the
kzalloc fails to avoid it.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add DMA support to the MSIOF driver using platform data.
As MSIOF DMA is limited to 32-bit words (requiring byte/wordswapping for
smaller wordsizes), and the group length is limited to 256 words, DMA is
performed on two fixed pages, allocated and mapped at driver initialization
time.
Performance figures (in Mbps) on r8a7791/koelsch at different SPI clock
frequencies for 1024-byte and 4096-byte transfers:
1024 bytes 4096 bytes
- 3.25 MHz: PIO 2.1, DMA 2.6 | PIO 2.8, DMA 3.1
- 6.5 MHz: PIO 3.2, DMA 4.4 | PIO 5.0, DMA 5.9
- 13 MHz: PIO 4.2, DMA 6.6 | PIO 8.2, DMA 10.7
- 26 MHz: PIO 5.9, DMA 10.4 | PIO 12.4, DMA 18.4
Note that DMA is only faster than PIO for transfers that exceed the FIFO
size (typically 64 words / 256 bytes).
Also note that large transfers (larger than the group length for DMA, or
larger than the FIFO size for PIO), should use cs-gpio (with the
appropriate pinmux setup), as the hardware chipselect will be deasserted in
between chunks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes the following build error introduced by commit b3f6a57506
("spi: omap-uwire: use devm_ functions"):
drivers/spi/spi-omap-uwire.c:465:2: error: implicit declaration of function ‘devm_ioremap’
Since we are including <linux/io.h>, <asm/io.h> is no longer
needed. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes the chip select function. Chip select should instead be
supported using GPIOs, defining the DT entry "cs-gpios", and letting the SPI
core assert/deassert the chip select as it sees fit.
The chip select control inside the controller is buggy. It is supposed to
automatically assert the chip select based on the activity in the controller,
but it is buggy and doesn't work at all. So instead we elect to use GPIOs.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch introduces the use of devm_clk_get and devm_ioremap instead
of the unmanaged interfaces and removes the corresponding free function
calls.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add trivial runtime PM support. This will only be of benefit on SoCs
where the clock to the SPI interface can be shut down.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_prepare()/clk_enable() can fail, and it's return value should
be checked. Add the proper checking, and while we're here, convert
to clk_prepare_enable().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Move buffer pointer and length setup to the top,
- Make unsigned values unsigned,
- Loop over words and increment pointers instead of recalculating them,
which allows to kill bytes_done.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Add a timeout when waiting for the transfer complete interrupt,
- If sh_msiof_spi_stop() fails, there's no need to clear IER, as the
interrupt handler has already done that,
- Propagate transfer failures in sh_msiof_transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Based on an old patch by Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let memory subsystem do the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for v1.1.1 of the SPI QUP controller.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch moves the devm_spi_register_master below the initialization of the
runtime_pm. If done in the wrong order, the spi_register_master fails if any
probed slave devices issue SPI transactions.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It was observed that after module removal followed by insertion,
the SW mode chipselect is not properly set. Thus causing transfer
failure due to incorrect CS toggling.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is to fix the SPI DMA transfer failure for speed less than 1M.
If using current DMA burst size setting (16), the Rx data bytes are
invalid due to each data byte is multiplied according to the burst
size setting.
Let's said supposedly we shall receive the following 18 bytes of data:
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18
Instead, the data bytes received consist of "16 bytes of '01' +
2 bytes of '02'" :
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 02 02
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extract the common parts of rspi_transfer_one(), rspi_rz_transfer_one(),
and qspi_transfer_out_in() into the new function rspi_common_transfer().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable DMA support for RSPI on r7s72100 (RZ/A1H).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable DMA support for QSPI on R-Car Gen2, for Single, Dual, and Quad SPI
Transfers.
Performance figures for reading from a QSPI FLASH driven at 24.375 MHz
on r8a7791/koelsch:
- Single: 1.1 Mbps PIO, 23 Mbps DMA
- Dual : 12.7 Mbps PIO, 48 Mbps DMA
- Quad : 13 Mbps PIO, 70 Mbps DMA
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_send_dma() and rspi_send_receive_dma() are very similar. Consolidate
into a single function rspi_dma_transfer(), and add missing checks for
dmaengine_submit() failures.
Both sg_table pointer parameters can be NULL, as RSPI supports TX-only
mode, and unidirectional DMA transfers will also be needed later for
Dual/Quad DMA support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA routines only need access to the scatter-gather tables inside the
spi_transfer structures, hence just pass those.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Refactor RSPI (on SH) DMA handling to make it reusable for other RSPI
implementations:
- Call the DMA routines after configuring the TX Mode bit and after
calling rspi_receive_init(), so these RSPI-specific operations can be
removed from the DMA routines,
- Absorb rspi_transfer_out_in() into rspi_transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the SPI core DMA mapping framework instead of our own.
If available, DMA is used for transfers larger than the FIFO size
(8 or 32 bytes).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SPI DMA core framework needs both RX and TX DMA to function. As a
preparation for converting the driver to use this framework, fall back to
PIO if no DMA channel or only one DMA channel is available.
This affects only RSPI, which could do DMA transfers for TX-only before.
RSPI-RZ and QSPI (at least for Single SPI Transfers) will need both RX and
TX DMA anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The resource is know to exist, as rspi_probe() already mapped it.
Remove the test, and just pass the resource.
Pass the device pointer instead of the platform device pointer, as the
latter is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Setup of the receive and transmit DMA channels is very similar, so let's
consolidate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fall back to PIO if DMA configuration failed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The various PIO loops are very similar. Consolidate into a single
function rspi_pio_transfer().
Both buffer pointers can be NULL, as RSPI supports TX-only mode, and
Dual/Quad SPI Transfers are unidirectional.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
RSPI needs dummy transfers to generate the SPI clock on receive.
RSPI-RZ and QSPI always do both transmit and receive.
Use the SPI core SPI_MASTER_MUST_RX/SPI_MASTER_MUST_TX infrastructure
instead of checking for the presence of buffers and providing dummy data
ourselves (for PIO), or providing a dummy buffer (for DMA).
rspi_receive_dma() now provides full duplex DMA transfers on RSPI, and is
renamed to rspi_send_receive_dma().
As the SPI core will always provide a TX buffer, the logic to choose
between DMA send and DMA send/receive in rspi_transfer_one() now has to
check for the presence of an RX buffer. Likewise for the DMA availability
tests in rspi_is_dma().
The buffer tests in qspi_transfer_one() are now always true, so they're
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 16-bit DMA support doesn't fit well within the SPI core DMA framework,
as it needs to manage its own double-sized temporary buffers, for handling
the interleaved data.
Remove it, as there is no in-tree board code that sets
rspi_plat_data.dma_width_16bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 8449fd76de ("spi: rspi: Merge
rspi_send_pio() and rspi_receive_pio()"), rspi_receive_init() is called
for transmit-only transfers too, while this is not needed.
Only call rspi_receive_init() when receiving, to preserve behavior on
RSPI on SH.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit 7dd6278733 (spi/pxa2xx: Convert
to core runtime PM) master->auto_runtime_pm was set to true.
In this case pm_runtime_enable() must be called *before*
spi_register_master(), otherwise the kernel hangs with this error
message:
spi_master spi0: Failed to power device: -13
A similar fix, but for spi/hspi, was applied in
268d76430d.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@linaro.org>
By default for every espi transfer, the rx_buf is placed right after the
tx_buf. This can lead to a buffer overflow when the size of both the TX
and RX data cumulated is higher than the allocated 64K buffer for the
transfer (this is the case when sending for instance a read command and
reading 64K back, please see:
http://article.gmane.org/gmane.linux.drivers.mtd/53411 )
This gets fixed by always setting the RX buffer pointer at the begining
of the transfer buffer.
[The driver shouldn't be doing the copy in the first place and instead
sending directly from the supplied buffer but this is at least not worse
than what's there -- broonie]
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rejecting unsupported values of spi-tx-bus-width and spi-rx-bus-width
may break compatibility with future DTs. Just ignore them, falling back
to Single SPI Transfers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The calculation of the bit rate divider used a standard C division, which
rounds down the quotient. This may lead to a higher bitrate than requested.
Round up to avoid this.
E.g. on Koelsch, the SPI flash (configured for 30 MHz) was driven at 48.75
MHz. After this patch it's driven at a safe 24.375 MHz.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
current PIO tranfer method be described as follows:
1. fill as much as bytes but no more than 256 bytes(fifo size)
2. enable oflow/uflow/txfifo_empty interrupt
3. isr process 3 interrupt signal, do complete works.
4. after isr done, if there are left bytes go into 1 else go into 5
5. transfer end
by current PIO transfer method:
1. reduce interrupt counts in spi interrupt line.
2. reduce interrupt latency because no do data fill/fetch in isr.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The spi-topcliff-pch driver is for a companion chip to the Intel Atom
E600 series processors. These are 32-bit x86 processors so the driver
is only needed on X86_32. Add COMPILE_TEST as an alternative, so that
the driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the calculation for determining whether to use FIFO or BLOCK
mode.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case we are doing DMA transfer and the size of the buffer is not multiple
of 4 bytes the driver truncates that to 4-byte boundary and tries to handle
remaining bytes using PIO.
Or that is what it tried to do. What actually happens is that it calls
ALIGN() to the buffer size which aligns it to the next 4-byte boundary
(doesn't truncate). Doing this results 1-3 bytes extra to be transferred.
Furthermore we handle remaining bytes using PIO which results one extra
byte to be transferred. In worst case the driver transfers 4 extra bytes.
While investigating this it turned out that the DMA hardware doesn't even
have such limitation so we can solve this by dropping the code that tries
to handle unaligned bytes.
Reported-by: Chiau Ee Chew <chiau.ee.chew@intel.com>
Reported-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The dw_spi_cleanup() function was removed by commit c63f5da008
"spi: dw: Don't call kfree for memory allocated by devm_kzalloc".
commit ec37e8e1f0 "spi: dw: migrate to generic queue infrastructure" added
dw_spi_cleanup() but never use it. So now I got below build warning:
CC [M] drivers/spi/spi-dw.o
drivers/spi/spi-dw.c:609:13: warning: 'dw_spi_cleanup' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Found using smatch:
drivers/spi/spi-atmel.c:878 atmel_spi_pump_pio_data() warn: unsigned
'as->current_remaining_bytes' is never less than zero.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If we fail to create the master queue for some reason we should not attempt
to clean it up since attempting to stop a kthread that was not created will
hang and it's just generally bad practice. Unfortunately at present we call
spi_destroy_queue() even in cases where the creation fails.
Fix this by fixing the error handling in spi_master_initialize_queue() so
that we only flag the master as queued or destroy the queue if creation
succeeded. The change to the flag is done since the general master
cleanup uses this to destroy the queue.
Reported-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
If NO_DMA=y:
drivers/built-in.o: In function `spi_map_buf':
spi.c:(.text+0x21bc60): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `spi_unmap_buf.isra.33':
spi.c:(.text+0x21c32e): undefined reference to `dma_unmap_sg'
make[3]: *** [vmlinux] Error 1
Protect the DMA code by #ifdef CONFIG_HAS_DMA to fix this:
- Extract __spi_map_msg() from spi_map_msg(),
- Provide dummy definitions of __spi_map_msg() and spi_unmap_msg() if
!CONFIG_HAS_DMA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also, use this opportunity to let spi_chip_sel() handle chip-select
deactivation as well.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
The availability of SPI Dual or Quad Transfer Mode as indicated by the
"spi-tx-bus-width" and "spi-rx-bus-width" properties in the device tree is
a hardware property of the SPI master, SPI slave, and board wiring. Hence
the SPI core should not reject an SPI slave because an SPI master driver
doesn't (yet) support Dual or Quad Transfer Mode.
Change the lack of Dual or Quad Transfer Mode support in the SPI master
driver from an error condition to a warning condition, and ignore the
unsupported mode bits, falling back to Single Transfer Mode, to avoid
breakages when running old kernels with new device trees.
Fixes: f477b7fb13 (spi: DUAL and QUAD support)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Similar to CE4100, BayTrail LPSS SPI can be PCI enumerated
as well. Thus, the functions are renamed from ce4100_xxx
to pxa2xx_spi_pci_xxx to clarify that this is a generic
PCI glue layer. Also, added required infrastructure to
support SPI hosts with different configurations.
This patch is based on Mika Westerberg's previous work.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
atmel_spi_lock does a spin_lock_irqsave, so we need to renable the
interrupts when we want to schedule.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make FSL eSPI CSnBEF and CSnAFT fields in ESPI_SPMODEn registers
(n=0,1,2,3) configurable through device tree.
CSnBEF is the chip select setup time. It's the delay in bits from the
activation of chip select pin to the first clock for data frame.
CSnAFT is the chip select hold time. It's the delay in bits from the
last clock for data frame to the deactivation of chip select pin.
The FSL eSPI driver hardcodes CSnBEF and CSnAFT to 0. Need to set
them to a different value for some device.
Signed-off-by: Jane Wan <Jane.Wan@gainspeed.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
split sirfsoc_spi_transfer function into 3 sub-functions:
spi_sirfsoc_cmd_transfer, spi_sirfsoc_pio_transfer and
spi_sirfsoc_dma_transfer.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dependency on ARM in Kconfig.
This is to fix the build error related to _relaxed IO.
Remove dependency on SPI_MASTER because this is already defined
under if SPI_MASTER in Kconfig.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than requesting the shyway_clk call clk_get with
the device and a NULL con_id.
This is in keeping with the way that clk_get() is called
on other drivers used by Renesas Gen 1 SoCs. And I believe
it is compatible with supplying clocks via DT, unlike the current code.
It appears to me that the two uses of this driver are
the r8a7778 and r8a7779 SoCs.
The r8a7779 already has clocks setup to allow this driver to continue to work
with this change applied.
The r8a7778 has clocks incorrectly setup to allow this driver to continue
to work with this change applied. This problem is addressed in
"ARM: shmobile: r8a7778: Use clks as MSTP007 parent" which is thus
a pre-requisite of this patch.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@linaro.org>
sometimes t->tx can be equal with t->rx. for example, spidev will make
tx and rx point to spidev->buffer at the same time. currently, for this
case, we map the buffer BIDIRECTION to fix the cache consistency.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fix a lot of "line over 80 characters" checkpatch issues, on which
the users of the driver, key customers care about this very much.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
orignal GPIO chipslect is not standard because it don't take care to the
chipselect signal: BITBANG_CS_ACTIVE and BITBANG_CS_INACTIVE.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI bitbang supply "chipselect" interface for change chip-select line
, in the SiRFSoC SPI controller, we need to enable "SPI_CS_IO_MODE",
otherwise, spi_sirfsoc_chipselect() has no effect.
now the driver is working is because SPI controller will control CS
automatically without SPI_CS_IO_MODE. this patch makes the CS controller
really controlled by software.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
the old code uses wrong marco - SIRFSOC_SPI_FIFO_FULL is not for
FIFO interrupt status, it is for FIFO status. here in the ISR,
SIRFSOC_SPI_TXFIFO_EMPTY is the right bit for SPI TXFIFO interrupt
status.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add driver for Cadence SPI controller. This is used in Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Spi v3 controller is not only used on Blackfin. So rename it
and use ioread/iowrite api to make it work on other platform.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify the cleanup code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
mpc8xxx_spi_probe() has set master->cleanup = mpc8xxx_spi_cleanup,
however current code overrides the setting in fsl_spi_probe() and set
master->cleanup = fsl_spi_cleanup.
Thus the memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In current code, master->cleanup and master->setup are not set in the same
function. This makes it hard to read and not good for code maintain.
One example is in fsl-spi.c, master->cleanup is overrided in mpc8xxx_spi_probe()
which leads to a memory leak.
This patch removes mpc8xxx_spi_cleanup() and converts fsl_espi_setup to use
devm_kzalloc so we don't need to take care of freeing memory.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
add optional property devicetree for SPI slave nodes
into devicetree so that LSB mode can be enabled by devicetree.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The existing timeout value in wait_for_completion_timeout is
calculated from the transfer length and speed with tolerance of 10msec.
This is too low because this is used for error conditions such as
hardware hang etc.
The xfer->speed_hz considered may not be the actual speed set
because the best clock divisor is chosen from a limited set such that
the actual speed <= requested speed. This will lead to timeout being
less than actual transfer time.
Considering acceptable latencies, this timeout can be set to a
value double the expected transfer plus 100 msecs.
This patch adds the same in the core.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't use unsigned for current_remaining_bytes so we can check
current_remaining_bytes < 0 case.
Use int is enough for current_remaining_bytes.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A few driver specific fixes, the main one being the fix for handling of
complete callbacks that are open coded in individual drivers to allow
callers to omit the completion. As we move things into the core that
sort of issue should become less and less common.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTR8jpAAoJELSic+t+oim9R3YQAJ1SjEGkdZ2T41pASsm1otmW
o0mS5j+YSPvW+H7XxOFfGed51Mw+TUKgIrxOutHZOKqYbeqikphbGqOAcRlcmNZ2
H7REdmlYT0EFBd+K2mNDqoOL9c56kxldEzJBXXu9keAJcY358Fl9gOpIz55py+CS
ftrf1A6Vvwiyvlk9/AkmR1n+PlRrDP881C1DGK+q4yoHlKbJylqTzkdK/DTO4AgU
wSPtK9NAciq6gBjInWwZA83GRioCAk5pvHTyXVn9IcS7g2J7AAtObDg5w8LmZ2GD
1/QS47S6IL5ksdQ464RS6tmQamm422C3KWJuYejJt4UVtlL6QCWeM+baj7HgwbHR
/DFs+Zgi2tZABtqo5stOCNl75gr8aOY75M0fc0Hm4OeJlKA5DoxT8aC5mrTT2z+j
cF1Ro6v9rHSRm0WE+ZoD3ykyWmjHnoXTNa6Fhy4g8712BdWpEiNnfsTaPvvz7I8w
BlKdAoCB2BHPMAzbe2FO/RLsi387rmbDdYP5nSj5iCIKkCMhX2E9XuAnJ1tNhQ+y
IsY88DPIr10OXOJht5TPMVY+R+6SJj4yJFRVwJOXjlxJhHcjIBSUSH8v2qp3SEfG
sUXR8bacFsE5TRnE2vRx7CsjPUxp3If5X/POmAGURwWOGo3RlUICr9pzbAHyP4xt
tOHlGZnutsHv/2ZflCBh
=rgeq
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the main one being the fix for handling
of complete callbacks that are open coded in individual drivers to
allow callers to omit the completion. As we move things into the core
that sort of issue should become less and less common"
* tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Depend on ARCH_QCOM
spi: efm32: Update binding document to make "efm32,location" property optional
spi: omap2-mcspi: Convert to use devm_kcalloc
spi: Always check complete callback before calling it
Commit 8fc1b0f87d ("ARM: qcom: Split Qualcomm support into legacy and
multiplatform") removed Kconfig symbol ARCH_MSM_DT. But that commit
left one (optional) dependency on ARCH_MSM_DT untouched.
Three Kconfig symbols used to depend on ARCH_MSM_DT: ARCH_MSM8X60,
ARCH_MSM8960, and ARCH_MSM8974. These three symbols now depend on
ARCH_QCOM. So it appears this driver needs to depend on ARCH_QCOM too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This saves a few unwind code and return proper error if devm_kcalloc fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 1e25cd4729 "spi: Do not require a completion", this checking is
required to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull MIPS updates from Ralf Baechle:
- Support for Imgtec's Aptiv family of MIPS cores.
- Improved detection of BCM47xx configurations.
- Fix hiberation for certain configurations.
- Add support for the Chinese Loongson 3 CPU, a MIPS64 R2 core and
systems.
- Detection and support for the MIPS P5600 core.
- A few more random fixes that didn't make 3.14.
- Support for the EVA Extended Virtual Addressing
- Switch Alchemy to the platform PATA driver
- Complete unification of Alchemy support
- Allow availability of I/O cache coherency to be runtime detected
- Improvments to multiprocessing support for Imgtec platforms
- A few microoptimizations
- Cleanups of FPU support
- Paul Gortmaker's fixes for the init stuff
- Support for seccomp
* 'mips-for-linux-next' of git://git.linux-mips.org/pub/scm/ralf/upstream-sfr: (165 commits)
MIPS: CPC: Use __raw_ memory access functions
MIPS: CM: use __raw_ memory access functions
MIPS: Fix warning when including smp-ops.h with CONFIG_SMP=n
MIPS: Malta: GIC IPIs may be used without MT
MIPS: smp-mt: Use common GIC IPI implementation
MIPS: smp-cmp: Remove incorrect core number probe
MIPS: Fix gigaton of warning building with microMIPS.
MIPS: Fix core number detection for MT cores
MIPS: MT: core_nvpes function to retrieve VPE count
MIPS: Provide empty mips_mt_set_cpuoptions when CONFIG_MIPS_MT=n
MIPS: Lasat: Replace del_timer by del_timer_sync
MIPS: Malta: Setup PM I/O region on boot
MIPS: Loongson: Add a Loongson-3 default config file
MIPS: Loongson 3: Add CPU hotplug support
MIPS: Loongson 3: Add Loongson-3 SMP support
MIPS: Loongson: Add Loongson-3 Kconfig options
MIPS: Loongson: Add swiotlb to support All-Memory DMA
MIPS: Loongson 3: Add serial port support
MIPS: Loongson 3: Add IRQ init and dispatch support
MIPS: Loongson 3: Add HT-linked PCI support
...
The core implementation of cs_change didn't follow the documentation
which says that cs_change in the middle of the transfer means to briefly
deassert chip select, instead it followed buggy drivers which change the
polarity of chip select. Use a delay of 10us between deassert and
reassert simply from pulling numbers out of a hat.
Reported-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8-bit word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Also remove the duplicate code to test spi->mode, it is done by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With devm_kzalloc, the memory is automatically freed when spi_device detach from
the bus.
Fixes: commit 43f627ac9d (spi: dw: fix memory leak on error path)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stabe@vger.kernel.org
The memory allocated for chip is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes the following coccicheck warning:
linux-2.6/drivers/spi/spi-omap-uwire.c:485:2-8: ERROR: missing iounmap; ioremap on line 471 and execution via conditional on line 481
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set highest transfer speed to master->max_speed_hz and then we can remove
hw->max_speed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch merges support for all DB1xxx and PB1xxx
boards into a single image, along with a new single defconfig
for them.
Run-tested on DB1300 and DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6577/
Patchwork: https://patchwork.linux-mips.org/patch/6659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver sets the SPI_MASTER_HALF_DUPLEX flag, so the spi core will check
transfers to ensure they are not full duplex.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no real reason why we require transfers to have a completion and
the only user of the completion now checks to see if one has been provided
before using it so stop enforcing this. This makes it more convenient for
drivers to chain multiple asynchronous transfers together.
Signed-off-by: Mark Brown <broonie@linaro.org>
If during a SPI transfer with len larger than PCH_MAX_FIFO_DEPTH and the
IRQ handler happens to be called when the transmit FIFO is already empty,
and SPSR_FI_BIT is set consequently, the message
"spi_master spi32766: pch_spi_handler_sub : Transfer is not completed"
is spammed to the systemlog, because tx_index has already increased
further due to the next bytes to be written. This case is uncritical as
new bytes have already been written.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
spi core will use spi->max_speed_hz as transfer speed if the transfer speed was
not set. So we don't need to test t->speed_hz in mcfqspi_transfer_one().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch removes <mach/hardware.h> dependency. This is performed
by replace hard coded used memory regions and interrupt to getting
these values from resources passed to the driver. For the system-wide
registers we now able to use SYSCON driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure all registered platform devices are unregistered on probe() error paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The definition of struct altera_spi_platform_data does not exist in current
tree. So remove the code to get platform_data which is never used.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_mpc8xxx_spi_probe() allocates memory for pinfo but the memory is not freed
anywhere. of_mpc8xxx_spi_probe() is called in .probe() and pinfo should be
freed in .remove(), so convert kzalloc to devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps increasing build testing coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The correct way to set multiple bits settings is always clear these
bit fields before set new settings.
Current code does not cause problem because the reset value of these
bit fields are 0, and these settings only set once during probe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix printk format warning by using %p extension 'ad' for dma_addr_t.
drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 7 has type 'dma_addr_t' [-Wformat]
drivers/spi/spi-atmel.c:1228:3: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The tnetv107x platform is getting removed, so this driver
will not be needed any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When xfer->speed_hz is greater than master->max_speed_hz, it's generally safe
to use master->max_speed_hz as transfer speed.
Thus use master->max_speed_hz as transfer speed rather than return error when
xfer->speed_hz > master->max_speed_hz.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
While reviewing an i2c driver for efm32 that needs a similar property
Wolfram Sang pointed out that "location" is a too generic name for
something that is efm32 specific. So add an appropriate namespace and
fall back to the generic name in case of failure.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If sp->info is NULL, we will hit NULL pointer dereference in probe() while
setting bus_num and num_chipselect for master:
sp->bitbang.master->bus_num = sp->info->bus_num;
sp->bitbang.master->num_chipselect = sp->info->num_chipselect;
Thus add NULL test for sp->info in probe() to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is required since commit 2025172e32 "spi/bitbang: Use core message pump".
spi-bitbang now uses core message pump, so it needs to call spi_master_suspend/
spi_master_resume to stop/start the queue while suspend/resume.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver does not work for bits_per_word greater than 16.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already has NULL test for master after calling spi_alloc_master().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same logic in spi_clps711x_setup_xfer() and
spi_clps711x_transfer_one().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set master->max_speed_hz and master->min_speed_hz then spi core will handle
checking transfer speed. So we can remove the same checking in this driver.
This patch also remove testing if hz is 0 because spi->max_speed_hz will be
default set to master->min_speed_hz if it was not set. So the transfer speed
will never set to 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This simple SPI master controller is built into xtfpga bitstreams. It
always transfers 16 bit words in SPI mode 0, automatically asserting CS
on transfer start and deasserting on end.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a DT-only driver, so remove all non-DT paths.
of_gpio_named_count() may fail, thus also add checking it's return value.
efm32_spi_probe_dt() never fails, make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If pdata->cs_control is NULL, we will hit NULL pointer dereference in
mcfqspi_cs_select() and mcfqspi_cs_deselect(). Thus add NULL test for
pdata->cs_control in probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The label argument was removed by commit 989847967c
spi: clps711x: Use devm_gpio_request(), add it back.
This makes it easier to know the gpio usage in /sys/kernel/debug/gpio.
Also remove unnecessary gpio_is_valid() checking, devm_gpio_request() returns
error if the requested gpio is invalid.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This ensures clock has been enabled before calling spi_master_resume().
while at it, also add checking return value of spi_master_suspend and
spi_master_resume because they may fail.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
mmap resource requirement is only for memory mapped operations.
If the user does not populate mmap resource, dont call return,
instead we go on for normal spi mode operations.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is required since commit 2025172e32 "spi/bitbang: Use core message pump".
spi-bitbang now uses core message pump, so it needs to call spi_master_suspend/
spi_master_resume to start/stop the queue while suspend/resume.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously only the resources controlled by the driver were put into
low power state at system suspend. Both the amba bus and a potential
power domain were ignored.
Moreover, while putting the device into low power state we first
brought it back to full power, but for no particular reason.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch issues.
ERROR: space prohibited after that open parenthesis '('
ERROR: space required before the open parenthesis '('
ERROR: trailing statements should be on next line
ERROR: space required after that ',' (ctx:VxV)
ERROR: spaces required around that '-=' (ctx:VxV)
WARNING: sizeof *cs should be sizeof(*cs)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The PM callbacks implemented by the spi-atmel driver don't call
spi_master_{resume,suspend}, fix that.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to use default implementation of transfer_one_message().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
dev_get_drvdata() returns the address of master rather than mcfqspi.
Fixes: af361079 (spi/coldfire-qspi: Drop extra calls to spi_master_get in suspend/resume functions)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Current code set platform drvdata to dspi. However, the code in dspi_suspend()
and dspi_resume() assumes the drvdata is the address of master.
Fix it by setting platform drvdata to master.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Amend the spi atmel pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an spitransfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
