Commit Graph

335 Commits

Author SHA1 Message Date
Mark A. Greer
0a1de84205 NFC: trf7970a: Return error code when turning on RF fails
trf7970a_switch_rf_on() is currently a void function
but turning on the RF could fail so it should return
a return code.  That return code should also be
propagated back to the entity that initiated the
action.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:44 +02:00
Mark A. Greer
afa5b5f13e NFC: trf7970a: Ensure no more RX data before completing receive
Depending on the interrupt status value given by the
trf7970a, the driver may not know when a receive operation
is complete.  To handle this, the driver waits for a period
of time in case the trf7970a interrupts it again indicating
there are more RX data in the FIFO.  It is possible that the
timeout will occur when there are RX data in the FIFO but
before the trf7970a has generated an interrupt to tell the
driver about it.  Handle this by calling trf7970a_drain_fifo()
(instead of trf7970a_send_upstream() which just passes up the
data gathered to far) to check if there are more data in the
FIFO.  If so, gather that data into the receive buffer.  If
not, pass the data collected so far upstream as before.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:44 +02:00
Mark A. Greer
5d8f759424 NFC: trf7970a: Reread FIFO Status Register when draining FIFO
Receiving an interrupt whose Interrupt Status Register
value has only the SRX bit set is supposed to mean that
all of the data from the tag has been received.  That
turns out to not be true so we need to reread the FIFO
Status Register to tell if there are any new bytes in
the FIFO.  If there are, continue receiving them; if
there aren't, assume that the receive is complete and
pass the data up.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:44 +02:00
Mark A. Greer
bece3c544f NFC: trf7970a: Handle low-watermark IRQ when transmitting
Commit 4dd836e46c ("NFC: trf7970a: Reset FIFO when
'End of TX' Interrupt Occurs") fixes the issue that
it was meant to fix but adds the unfortunate side
effect of causing the driver to report an error
when the TX low-watermark level is passed during
transmits.  This can be fixed by checking whether
the IRQ status indicates that the low-watermark
has been passed when transmitting.  If it has been
passed and the FIFO is empty, then its safe to reset
the FIFO.  Otherwise, silently continue since another
TX interrupt will be generated and the FIFO will be
reset then.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:44 +02:00
Mark A. Greer
0e840ed59b NFC: trf7970a: Only fill FIFO if there is space
Handle the case where trf7970a_fill_fifo() is
called but there is no room in the FIFO for
more TX data.  When this happens, wait for
another interrupt indicating that there is
now space (and set a timer in case that
interrupt never occurs).

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
7a1e5552af NFC: trf7970a: Prefix TX data when refilling FIFO
When refilling the FIFO with more TX data (using a new
SPI transaction), the driver must prefix the TX data with
a write to the FIFO I/O Register.  This tells the trf7970a
that the following data is destined for the FIFO so it can
be transmitted.

To accomplish this, the driver cannot simply push the
prefix data just before the next set of TX data that
is to be transmitted because that will overwrite part
of the TX data provided by the digital layer.  Instead,
separate the prefix data and the TX data when calling
trf7970a_transmit().  trf7970a_transmit() can then send
the prefix and TX data from different memory locations
with one spi_sync() operation.  This also means that
the driver doesn't require any skb "tx_headroom" as
provided by the digital layer (see
nfc_digital_allocate_device() and digital_skb_alloc()).

Also ensure that the prefix is of type 'u8' and not
'char'.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
5974150dea NFC: trf7970a: Remove unnecessary FIFO reset & RSSI read
It is no longer necessary to reset the FIFO and
read the 'RSSI Levels and Oscillator Status Register'
so remove that code.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
aff0564aa7 NFC: trf7970a: Clear possible spurious interrupt before transmitting
The trf7970a occasionally generates spurious interrupts
which can confuse the driver.  To help alleviate this,
clear any interrupts by reading the 'IRQ Status Register'
before starting a new transaction.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
38b4eb1f7f NFC: trf7970a: Recalculate driver timeout values
Some of the timeout values used in the driver
are not long enough to handle worst-case scenarios
so they need to be recalculated.

The time to wait for the FIFO to drain past the
low-watermark is now 20 ms because it can take
around 14.35 ms to send 95 bytes (127 bytes in
full FIFO minus 32 bytes where the low-watermark
interrupt will fire).  95 bytes will take around
14.35 ms at 6.62 kbps (the lowest supported bit
rate used by ISO/IEC 15693) so 20 ms should be a
safe value.

The time to wait before issuing an EOF to complete
an ISO/IEC 15693 write or lock command is 40 ms--
20 ms to drain the FIFO and another 20 ms to ensure
the wait is long enough before sending an EOF.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
4e64eff837 NFC: trf7970a: Add RF technology specific guard times
When turning on the RF field, the driver must wait
an RF-technology-specific amount of time (known as
the guard time) before modulating the field.
Currently, the driver waits 5 ms but that is too
short for NFCF and too long for ISO/IEC 15693.
Fix this by determining the guard time when the
RF technology is set and delaying that amount
of time when turning on the RF field.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
a08e54549e NFC: trf7970a: Initialize when enabling RF
Currently, the trf7970a is reset & initialized only
when the pm_runtime resume hook is called.  Instead,
initialize it every time the RF is enabled to ensure
that the trf7970a is quiesced and in a known state
before being set up for another RF technology.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
6c08df422e NFC: trf7970a: Disable SYS_CLK Output
Currently, support for providing the external
SYS_CLK signal on pin 27 is not supported so
turn it off by writing to the 'Modulator and
SYS_CLK Control' register immediately after
reset.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
17b2151733 NFC: trf7970a: Remove unnecessary sleep
There is no need to sleep for 1-2 ms before
transmitting a new command.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:43 +02:00
Mark A. Greer
1568bfef18 NFC: trf7970a: FIFO Size is really 127 bytes
Despite what the manual says, the FIFO size
on the trf7970a is really 127 bytes so make
the code respect that.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:42 +02:00
Mark A. Greer
4542e8345a NFC: trf7970a: Ignore Overflow bit in FIFO Status Register
The Overflow bit in the 'FIFO Status Register' has
proven to be untrustworthy so ignore it.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:42 +02:00
Mark A. Greer
3e7f335689 NFC: trf7970a: Use spi_sync() instead of spi_write_then_read()
To more efficiently handle long continuous reads,
use spi_sync() instead of spi_write_then_read().

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:42 +02:00
Mark A. Greer
24707296c7 NFC: trf7970a: Call spi_setup() to configure SPI communication
Call spi_setup() to configure SPI communication
with the trf7970a.  This will ensure that the
correct SPI parameters are used.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:42 +02:00
Mark A. Greer
cc8d715864 NFC: trf7970a: Remove trf7970a_tg_listen_mdaa()
Currently, the digital layer 'tg_listen_mdaa'
hook is not used and it isn't necessary to have
a stub routine so remove it.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:42 +02:00
Mark A. Greer
d3a6d33a7f NFC: trf7970a: Remove incorrect of_node_put() call
of_property_read_u32() does not take a reference
to the specified OF node so don't call of_node_put()
in trf7970a_get_autosuspend_delay().

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-07 23:13:42 +02:00
Dan Carpenter
d07f1e8600 NFC: microread: Potential overflows in microread_target_discovered()
Smatch says that skb->data is untrusted so we need to check to make sure
that the memcpy() doesn't overflow.

Fixes: cfad1ba871 ('NFC: Initial support for Inside Secure microread')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-05 00:57:32 +02:00
Mark A. Greer
f23b73526b NFC: trf7970a: Make gpio labels more readable
Make the labels for the two gpio enable lines
more user friendly by prefixing them with the
driver name.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-01 00:06:56 +02:00
Mark A. Greer
95064bd95a NFC: trf7970a: Add quirk to keep EN2 low
A bug has been discovered in the trf7970a where it
will generate an RF field even in passive target
mode when EN2 is asserted.  To work around this,
add support for the 'en2-rf-quirk' device tree
property which indicates that EN2 must remain low.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-01 00:06:55 +02:00
Mark A. Greer
772079eb77 NFC: trf7970a: Move IRQ Status Read quirk to device tree
The quirk indicating whether the trf7970a has
the "IRQ Status Read" erratum or not is currently
implemented using the 'driver_data' member of the
'spi_device_id' structure.  That requires the
driver to be modified to turn the quirk off when
a version of the trf7970a that doesn't have the
erratum is being used.  To fix that, create a
new device tree property called
'irq-status-read-quirk' that indicates that the
trf7970a being used has the erratum.

While at it, rename 'TRF7970A_QUIRK_IRQ_STATUS_READ_ERRATA'
to 'TRF7970A_QUIRK_IRQ_STATUS_READ' to make it
less of an eyesore.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-01 00:06:55 +02:00
Mark A. Greer
3bd14233aa NFC: trf7970a: Add VIN voltage override support
The trf7970a driver uses the voltage from the
power/regulator subsystem to determine what the
voltage on the VIN pin is.  Normally, this is
the right thing to do but sometimes the board
that the trf7970a is on may change the voltage.
This is the case for the trf7970atb board from
Texas Instruments where it boosts the VIN voltage
from 3.3V to 5V (see http://www.ti.com/tool/trf7970atb).

To handle this, add support for the 'vin-voltage-override'
device tree property which overrides the voltage value
given by the regulator subsystem.  When the DT property
is not present, the value from the regulator subsystem
is used.

The value of 'vin-voltage-override' is in uVolts.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-09-01 00:06:55 +02:00
Christophe Ricard
1892bf844e NFC: st21nfca: Adding P2P support to st21nfca in Initiator & Target mode
Support for Initiator and Target mode with ISO18092 commands support:
- ATR_REQ/ATR_RES
- PSL_REQ/PSL_RES
- DEP_REQ/DEP_RES

Work based on net/nfc/digital_dep.c.
st21nfca is using:
- Gate reader F for P2P in initiator mode.
- Gate card F for P2P in target mode.

Felica tag and p2p are differentiated with NFCID2.
When starting with 01FE it is acting in p2p mode.

On complete_target_discovered on ST21NFCA_RF_READER_F_GATE
supported_protocols is set to NFC_PROTO_NFC_DEP_MASK
for P2P.

Tested against: Nexus S, Galaxy S2, Galaxy S3, Galaxy S3 Mini,
Nexus 4 & Nexus 5.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-07-23 01:14:41 +02:00
Christophe Ricard
d57d74eb76 NFC: st21nfca: Implement stop_poll HCI hook
Send DM_DISCONNECT command to disconnect Terminal Host from the HCI network.

- The persistent states of the terminal host pipes, including registry values,
are not modifies. Therefore, there is no NVRAM update to disconnect the
terminal host.
- The terminal host RF card gates are disabled which means that there will be no event
related to card RF gates until communication has been restored.
- The terminal host RF reader request is reset so the RF reader polling for terminal
host is disabled.

To restore the communication, the terminal host can send any HCI command or event.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-07-23 01:04:31 +02:00
Christophe Ricard
0531107e1c NFC: st21nfca: Improve read length sequence for P2P mode.
A DEP_RES with a SUPERVISOR PDU can be up to 16 bytes long.

In order to avoid useless read during p2p, extend first read
sequence to 16 and reduce third sequence to 12 to keep same
total on the full sequence.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-07-23 01:04:31 +02:00
Christophe Ricard
8e9466ccda NFC: st21nfca: Improved start of frame detection
A start of frame is 7E 00 not only 7E. Make sure the first read sequence is
starting with 7E 00.
For example: 7E FF FF FF FF is as a correct crc but it is a bad frame.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-07-23 01:04:31 +02:00
Christophe Ricard
cf577344e2 NFC: st21nfca: Free buffer in case no data are retrieved.
In case no data are retrieve through i2c or one specific case is not handled.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-07-23 01:04:30 +02:00
Christophe Ricard
fb92ff78f8 NFC: st21nfcb: few code clean up
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-07-23 00:49:37 +02:00
Christophe Ricard
35630df68d NFC: st21nfcb: Add driver for STMicroelectronics ST21NFCB NFC chip
Add driver for STMicroelectronics ST21NFCB NFC controller.
ST21NFCB is using NCI protocol and a proprietary low level transport
protocol called NDLC used on top.

NDLC:
The protocol defines 2 types of frame:
- One type carrying NCI data (referred as DATAFRAME frames).
- One type carrying protocol information used for flow control and error
control mechanisms (referred as SUPERVISOR frames).

After each frame transmission to the NFC controller, the device host
SHALL waitfor  an ACK (SUPERVISOR frame) reception before sending a
new frame.
The NFC controller MAY send a frame at anytime to the device host.
The NFC controller MAY send a specific WAIT supervisor frame to indicate
to device host that a NCI data packet has been received but that it could
take significant time before the NFC controller sends an ACK and thus
allows next data reception.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-07-23 00:49:28 +02:00
Mark A. Greer
6857bb9627 NFC: trf7970a: Add support for Felica Type 3 tags
Add support for the Felica protocol and Type 3 tags.
Both 212 and 424 kbps are supported.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-26 01:28:28 +02:00
Thierry Escande
09592ccfc2 NFC: port100: Add support for type 4B tag
This patch adds support for ISO-DEP protocol over NFC-B rf technology
by adding NFC_PROTO_ISO14443_B to the supported protocols and an entry
for framing configuration.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-26 00:42:02 +02:00
Christophe Ricard
7974728094 NFC: st21nfca: Add ISO15693 Reader/Writer support
Add support for ISO/IEC 15693 RF technology and Type 5 tags.
ISO15963 is using proprietary gate 12.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-20 00:48:28 +02:00
Christophe Ricard
a779b8878c NFC: st21nfca: Improve load_session
In case anybody uses previous patchset with the CLF, add a check to make sure
missing pipe are created.
st21nfca returns its pipe list in the creation order (most recent latest).

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-20 00:48:06 +02:00
Christophe Ricard
c44cb2edd0 NFC: dts: st21nfca: Add device-tree (Open Firmware) support to st21nfca
Add functions to recover hardware resources from the device-tree
when not provided by the platform data.

Based on pn544 devicetree implementation

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-20 00:47:43 +02:00
Christophe Ricard
0c942b007b NFC: st21nfca: Free buffer when a bad frame is detected
When a bad frame is detected for a bad crc.
We were reallocating and loosing the previous frame pointer.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-05 01:04:10 +02:00
Christophe Ricard
a3c5d8fb7f NFC: st21nfca: Synchronize i2c Tx and Rx path
Stabilize communication by using a mutex.
This avoids running a write transaction during a read retry or a read
transaction during a write retry.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-05 01:01:23 +02:00
Christophe Ricard
c97ffdbf51 NFC: st21nfca: Improved i2c Rx data correctness check
A frame starts with ST21NFCA_SOF_EOF(0x7e) + 0x00.
A frame ends with ST21NFCA_SOF_EOF(0x7e).
It is possible that the i2c macrocell is stopped for other
communication interfaces with highest priority(RF or SWP).
This can be seen with some 0xFF data at the end of a received shdlc buffer.
If this happen we need to discard the frame because the CLF will repeat it.

In order to push accurate data to hci layer, we add the following fix:
- Instead of looking for the first 0x7e in the frame, check that the last
received byte is 0x7e.
- Check that the first frame reception block start with start of
frame(0x7e 0x00). If not, clear the buffer.
- Check that the next frame reception block do not start with start of
frame(0x7e). If so, clear the buffer.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-05 01:00:34 +02:00
Christophe Ricard
e1fb97b925 NFC: st21nfca: Fix st21nfca_hci_remove_len_crc tail room handling
There is no byte stuffing when data are stored in skb.
TAILROOM is 2 byte crc + 1 byte eof.

st21nfca_hci_remove_len_crc was doing an incorrect operation on
the TAILROOM data.
If shdlc timer T2 is triggered, it will request to send the same data.
Before every hci data was lost after st21nfca_hci_remove_len_crc.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-05 00:15:26 +02:00
Christophe Ricard
3096e25a3e NFC: st21nfca: Fix incorrect byte stuffing revocation
Byte stuffing was not correctly removed after a i2c read operation.
This was causing improper crc calculation when byte stuffing was
applied to more than 1 byte.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-05 00:06:27 +02:00
Christophe Ricard
0bb8a622d6 NFC: st21nfca: Remove few useless include
Remove unneeded includes from i2c.c

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-05-05 00:05:36 +02:00
Christophe Ricard
18d2c624f9 NFC: st21nfca: Improve st21nfca initialization by handling reboot properly
Change in st21nfca_hci_platform_init in order to handle in a better way the
internal reboot command.
Once the reboot is completed, the driver expect to receive a 0x7e filled
buffer.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:30 +02:00
Christophe Ricard
fcb45e6ab3 NFC: st21nfca: Reworked st21nfca_request_resources
Remove struct st21nfca_i2c_phy* as this parameter can be retrieve
through i2c_get_clientdata(client)

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:30 +02:00
Christophe Ricard
9bac75d0ec NFC: st21nfca: st21nfca_hci_i2c_probe returns st21nfca_hci_probe result.
st21nfca_hci_probe return 0 in case of successful call and a different
value in any other cases.

There is no need to check for st21nfca_hci_probe return as this will be
checked after st21nfca_hci_i2c_probe is completed.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:30 +02:00
Christophe Ricard
761a2c4f90 NFC: st21nfca: Add __packed to struct st21nfca_pipe_info
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:29 +02:00
Christophe Ricard
c5b0c370fc NFC: st21nfca: Remove sporadic wait_tab variable from functions.
wait_tab variable is already global and may create conflicts.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:29 +02:00
Christophe Ricard
e8efab6e6b NFC: st21nfca: Fix warning: array subscript is above array bounds
Fix "warning: array subscript is above array bounds" in load_session

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:29 +02:00
Christophe Ricard
cc3a9f7254 NFC: st21nfca: Fix sparse: cast to restricted __be16
Fixing "sparse: cast to restricted __be16" message when building with
make C=1 CF=-D__CHECK_ENDIAN__

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:29 +02:00
Clement Perrochaud
12b25dbf11 NFC: pn544_i2c: Fix null pointer exception when not using platform data
Fixes a null pointer exception occurring when the IRQ request in
pn544_hci_i2c_probe fails and no platform data is available.

Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:29 +02:00
Mark A. Greer
742b1f9fa2 NFC: trf7970a: Add support for the ISO/IEC 14443-B and Type 4B tags
Now that the NFC digital layer has support for the ISO/IEC 14443-B
protocol and type 4B tags, add the corresponding support to the
trf7970a driver.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:28 +02:00
Mark A. Greer
fd0c8280cf NFC: trf7970a: Add 'autosuspend-delay' DTS property
The trf7970a driver currently uses a fixed autosuspend delay of 30 seconds.
To enable users to customize the delay as they see fit, add support for the
new 'autosuspend-delay' DTS property (part of the nfc node) which can
override the default 30 seconds.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:28 +02:00
Mark A. Greer
18422e686e NFC: trf7970a: Don't return value from trf7970a_switch_rf_on()
trf7970a_switch_rf_on() no longer returns anything other than 0 so make
it void and clean up the code that checks for errors when its called.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:28 +02:00
Mark A. Greer
e6403b7c75 NFC: trf7970a: Add pm_runtime support
Add pm_runtime support by moving the code that enables the trf7970a to
the pm_runtime hook routines. The pm_runtime 'autosuspend' feature is
used so that the device isn't disabled until at least 30 seconds have
passed since trf7970a_switch_rf_off() was last called.

The result is that when trf7970a_switch_rf_on() is called, the device
will be enabled and initialized (if it isn't already).  When
trf7970a_switch_rf_off() is called, it will turn off the RF immediately
but leave the device enabled for at least 30 seconds.
If 30 seconds have passed and the pm_runtime facility decides to suspend
the driver, the device will be disabled then.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:28 +02:00
Mark A. Greer
a1d2dc5b40 NFC: trf7970a: Turn RF on after hardware is configured
The NFC digital layer calls the 'switch_rf' hook to turn the RF on before
it configures the RF technology and framing. There is potential to confuse
a tag doing it this way so don't enable the RF until the RF technology and
initial framing have been configured.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:27 +02:00
Mark A. Greer
ebcc5a0d08 NFC: trf7970a: Set correct Vin voltage in Chip Status Control register
Currently, the trf7970a driver assumes that the Vin voltage is 5V when
it writes to the 'Chip Status Control' register. That may not be correct
so use the regulator facility to get the Vin voltage and set the VRS5_3
bit correctly when writing to that register.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:27 +02:00
Mark A. Greer
12e9ade309 NFC: trf7970a: Allow different Modulator and SYS_CLK Control register values
Currently the driver writes the same value to the 'Modulator and SYS_CLK
Control' register no matter what RF technology is being used. That works
for now but new RF technologies (e.g., ISO/IEC 14443-B) will require
different values to be written to that register. To support this, add a
member to the trf7970a structure which is set by the RF technology handling
code and used by the framing code when it writes to that register.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:27 +02:00
Mark A. Greer
a0822a7e3b NFC: trf7970a: Set 'Modulator and SYS_CLK Control' after 'ISO Control'
Writing to the 'ISO Control' register may cause the contents of the
'Modulator and SYS_CLK Control' register to change so be sure to write
to 'Modulator and SYS_CLK Control' after writing to 'ISO Control'.

Note that writing to the 'Modulator and SYS_CLK Control' register
shouldn't be necessary at all according to the trf790a manual but testing
shows that it is necessary.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:27 +02:00
Mark A. Greer
49d19cc794 NFC: trf7970a: Only write 'ISO Control' when its changing
The current code always writes to the 'ISO Control' register when the
RF framing is set.  That's not necessary since the register's value
doesn't always change. Instead, only write to it when its value is
actually being changed.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:27 +02:00
Mark A. Greer
4dd836e46c NFC: trf7970a: Reset FIFO when 'End of TX' Interrupt Occurs
Sometimes after sending a frame there is tx data leftover in the FIFO
which the driver will think is part of the receive frame. That data can
be cleared when an 'End of TX' interrupt is received by issuing the
'FIFO Reset' command.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:27 +02:00
Mark A. Greer
b887eb09d3 NFC: trf7970a: Clear 'NFC Target Detection Level' register
Due to a trf7970a erratum, the 'NFC Target Detection Level' register
(0x18) must be cleared after power-up.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:27 +02:00
Mark A. Greer
5876bc75e2 NFC: trf7970a: Only abort a command if one is active
Only initiate the abort command process when there is an active command.
If the abort process were started and there wasn't an active command
then the next command issued by the digital layer would be incorrectly
aborted.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:26 +02:00
Mark A. Greer
5fa3af352b NFC: trf7970a: Increase TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT to 20 ms
After further testing periods of ~16 ms have been observed
between interrupts indicating that there is receive data in
the FIFO.  To accomodate that, increase the time the driver
waits before deciding there is no more data to receive to
20 ms.  The macro that represents that delay is
'TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT'.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:26 +02:00
Clement Perrochaud
eda8565af3 NFC: pn544: i2c: Add device-tree (Open Firmware) support to PN544
Add functions to recover hardware resources from the device-tree when not
provided by the platform data.

Signed-off-by: Clément Perrochaud <clement.perrochaud@nxp.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:26 +02:00
Christophe Ricard
58e1e0a920 NFC: st21nfca: Implement load_session HCI hook
This implementation rely on the ST21NFCA_DEVICE_MGNT_GATE and
ST21NFCA_DM_GETINFO proprietary gates commands.

First we are retrieving a pipe list available on the CLF with the
ST21NFCA_DM_GETINFO_PIPE_LIST parameter. A gate<->pipe table match
is done with ST21NFCA_DM_GETINFO_PIPE_INFO for each pipe.
If the pipe is created and open, we fill st21nfca_gates table.
If the pipe is create but closed or is not created we keep the gate
with NFC_HCI_INVALID_PIPE.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:26 +02:00
Christophe Ricard
68957303f4 NFC: ST21NFCA: Add driver for STMicroelectronics ST21NFCA NFC Chip
Add driver for STMicroelectronics ST21NFCA NFC controller.
ST21NFCA is using HCI protocol, shdlc as LLC layer & I2C as
communication protocol.

Adding support for Reader/Writer mode with Tag type 1/2/3/4 A & B.
It is using proprietary gate 15 for ISO14443-3 such as type 1 &
type 2 tags. It is using proprietary gate 14 for type F tags.
ST21NFCA_DEVICE_MGNT_GATE gives access to proprietary CLF configuration.
Standard gate for ISO14443-4 A (13) & B (11) are also used.

ST21NFCA specific mecanism:

One particular point to notice for the data handling is that frame
does not contain any length value. Therefore the i2c part of this driver
is managing the reception with a read length sequence until the end of
frame (0x7e) is reached.

In order to avoid conflict between sof & eof a mecanism
called byte stuffing concist of an escape byte (0x7d) insertion before
special byte (0x7e, 0x7d). The special byte is then xored with 0x20.

In this driver, When data are available in the CLF, the interrupt
gpio is driven to active state and triggered an interrupt.
Once the i2c_master_recv start, the interrupt gpio is driven to idle
state until its complete. If the frame is incomplete or data are still
available, interrupts will be triggered again.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-04-22 00:37:25 +02:00
Mark A. Greer
9d9304b321 NFC: trf7970a: Add ISO/IEC 15693 and Type 5 tag Support
Add support for ISO/IEC 15693 RF technology and Type 5 tags.
Note that Type 5 tags used to be referred to as Type V tags.

CC: Erick Macias <emacias@ti.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-03-11 00:47:09 +01:00
Mark A. Greer
8006289108 NFC: trf7970a: Add support for Type 4A Tags
Add support for Type 4A Tags which includes
supporting the underlying ISO/IEC 14443-A
protocol.

Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-03-11 00:47:08 +01:00
Mark A. Greer
165063f1da NFC: trf7970a: Add driver with ISO/IEC 14443 Type 2 Tag Support
Add a driver for the Texas Instruments TRF7970a RFID/NFC/15693
transceiver.  The driver currently supports ISO/IEC 14443 Type 2
tags only (MIFARE Ultralight and Ultralight C but not Classic).

CC: Erick Macias <emacias@ti.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-03-11 00:46:55 +01:00
Axel Lin
99968e0616 NFC: pn533: Convert to use USB_DEVICE macro
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-02-23 23:32:18 +01:00
Axel Lin
4aa7ed02f5 NFC: port100: Convert to use USB_DEVICE macro
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-02-23 23:32:18 +01:00
Thierry Escande
2a26f9a2c1 NFC: port100: Add support for type 4A tag platform
This adds support for ISO-DEP protocol over NFC-A rf technology. The
port100 already supports NFC-A and ATS request and response for type 4A
tags are handled at digital level. This patch adds NFC_PROTO_ISO14443
to the supported protocols and an entry for framing configuration which
is the same as NFC-A standard frame with CRC handling.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-02-16 23:49:54 +01:00
Thierry Escande
d3815ea95c NFC: port100: Fix possible buffer overflow
The arrays for protocols and rf techs must define a number of entries
corresponding to their maximum possible index values.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-02-16 23:49:54 +01:00
Arron Wang
f1dd56fdc4 NFC: pn544: i2c: Support PN544 C3 secure firmware download
PN544 C3 firmwares already contain the command frames to be sent, but as
they may exceed the i2c maximum payload, we need to fragment them into
secure chunks and send them through the secure write command.

Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-02-16 23:49:54 +01:00
Arron Wang
971d63cff6 NFC: pn544: Pass hardware variant information when downloading firmware
Different pn544 hardware variant may use different commands to download
new firmwares. The C2 does a regular firmware download while the C3 uses
a more secure protocol.
As a consequence we need to pass the hardware variant from the HCI SW
version command reply down to the pn544 i2c layer, in order to use the
right protocol at run time.

Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-02-16 23:49:54 +01:00
Amitkumar Karwar
bb55dc2ae4 NFC: nfcmrvl: Fix possible memory leak issue
This patch fixes memory leaks in the error paths of
nfcmrvl_nci_register_dev() routine.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-01-09 01:27:20 +01:00
Amitkumar Karwar
15203b4c79 NFC: nfcmrvl: Add setup handler
Marvell nfc device provides support for external coexistance
control. It allows Device Host to inhibit the NFCC from polling
when required by asserting a GPIO pin. A second pin allows the
DH to have feedback on the current NFCC state.

The required configuration for this feature is done in setup
handler.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-01-07 01:32:41 +01:00
Amitkumar Karwar
f26e30cc6b NFC: nfcmrvl: Initial commit for Marvell NFC driver
This patch adds NFC support for Marvell 8897 NFC-over-USB chipset.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-01-07 01:32:40 +01:00
Alexey Khoroshilov
c36aeba8c0 NFC: port100: Fix device leak
port100_probe() calls usb_get_dev(), but there is no usb_put_dev()
in port100_disconnect(). The patch adds one.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-01-05 00:49:00 +01:00
Samuel Ortiz
ea87a5efa9 NFC: pn533: Frame is invalid if ccid.datalen is 0
Some ACR122 firmwares seem to send 0 length data frames. Before using
that length as a data index, we check that it's not 0. If it is we
report the frame as being invalid.

Reported-by: Arthur Taylor <arthur@advancedtelematic.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-01-04 03:32:27 +01:00
Arman Uguray
34f7e57b23 NFC: pn544: Refactor hw_config values
Some of the EEPROM configurations that are assigned by the PN544 driver
are set by the firmware and should not be modified by the driver. Others
are certain user mode configurations that are currently getting set to values
that shouldn't necessarily be dictated by the driver. This patch changes
most user and system mode configurations to the firmware defaults.

Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-01-04 03:32:27 +01:00
Salil Kapur
fe0219cc50 NFC: mei_phy: Using kfree_skb() instead of kfree()
Using kfree_skb() instead of kfree() for struct sk_buff

Signed-off-by: Salil Kapur <salilkapur93@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2014-01-04 03:32:26 +01:00
Jeff Kirsher
98b32decc8 nfc: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment.  Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.

CC: linux-wireless@vger.kernel.org
CC: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
CC: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-11 10:56:21 -05:00
Thierry Escande
7227c0216d NFC: port100: Add target mode support
This implements the target NFC digital operations tg_configure_hw(),
tg_listen(), tg_listen_mdaa(), and tg_send_cmd().

The target mode supports NFC-A technology at 106kbits/s and NFC-F
technologies at 212 and 424kbits/s.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-10-07 14:11:20 +02:00
Thierry Escande
9f7b57f28c NFC: port100: Add initiator mode support
This patch implements the initiator NFC operations in_configure_hw()
and in_send_cmd(). It also implements the switch_rf() operation.

The initiator mode supports NFC-A technology at 106kbits/s and NFC-F
technologies at 212 and 424kbits/s.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-10-07 14:11:14 +02:00
Thierry Escande
0347a6ab30 NFC: port100: Commands mechanism implementation
This patch implements the command handling mechanism. The digital stack
serializes all commands sent to the driver. This means that the digital
stack waits for the reply of the current command before sending a new
one. So there is no command queue managed at driver level.

All Port-100 commands are asynchronous. If the command has been sent
successfully to the device, it replies with an ACK frame. Then the
command response is received (or actually no-response in case of
timeout or error) and a command complete work on the system workqueue
is responsible for sending the response (or the error) back to the
digital stack.

The digital stack requires some commands to be synchronous, mainly
hardware configuration ones. These commands use the asynchronous
command path but are made synchronous by using a completion object.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-10-07 14:10:52 +02:00
Thierry Escande
562d4d59b8 NFC: Sony Port-100 Series driver
This adds support for the Sony NFC USB dongle RC-S380, based on the
Port-100 chip. This dongle is an analog frontend and does not implement
the digital layer. This driver uses the nfc_digital module which is an
implementation of the NFC Digital Protocol stack.

This patch is a skeleton. It only registers the dongle against the NFC
digital protocol stack. All NFC digital operation functions are stubbed
out.

Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Cc: Stephen Tiedemann <stephen.tiedemann@gmail.com>
Tested-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-10-07 14:09:33 +02:00
Olivier Guiter
93ad42020c NFC: pn533: Target mode Tx fragmentation support
In target mode, when we want to send frames larger than the max length
(PN533_CMD_DATAEXCH_DATA_MAXLEN), we have to split the frame in smaller
chunks and send them, using a specific working queue, with the TgSetMetaData
command. TgSetMetaData sets his own MI bit in the PFB.
The last chunk is sent using the TgSetData command.

Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 16:02:24 +02:00
Olivier Guiter
3c13b244de NFC: pn533: Add support for incoming fragmented frame in target mode
This code processes, for Target Mode, incoming fragmented frames.
If the MI bit is present, we start a working queue to grab and aggregate
all the parts (using TmGetData between each parts). On the last one, as
there's no more MI bit, we jump on the usual behavior.

Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 16:01:41 +02:00
Olivier Guiter
22953f9329 NFC: pn533: Add MI/TG bits only when in Initiator mode
The fragmentation routine (used to split big frames) could be used in
target or initiator mode (TgSetMetaData vs InDataExchange), but the
MI/TG bytes are not needed in target mode (TgSetMetaData), so we
add a check on the mode

Signed-off-by: Olivier Guiter <olivier.guiter@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 16:01:03 +02:00
Sachin Kamat
e44666b981 NFC: pn533: Staticize local symbols
Local symbols used only in this file are made static.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 02:02:39 +02:00
Sachin Kamat
4b7449cdf4 NFC: nfcwilink: Remove redundant dev_set_drvdata
Driver core sets driver data to NULL upon failure or remove.

Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 02:02:37 +02:00
Samuel Ortiz
cec4b8edc9 NFC: pn533: Start listen timer from start_poll
If we start the polling loop from a listening cycle, we need to start
the corresponding timer as well.
This bug showed up after commit dfccd0f5 as it was impossible to start
from a listening cycle before it.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:41 +02:00
Samuel Ortiz
673088fb42 NFC: pn533: Send ATR_REQ directly for active device detection
In order to improve active devices detection, we send an ATR_REQ between
each passive detection cycle. Without this algorithm, Android 4.3 based
devices running the Broadcom stack are hardly detected.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:41 +02:00
Joe Perches
17936b43f0 NFC: Standardize logging style
Use standardized styles to minimize coding defects.

Always use nfc_<level> where feasible.
Add \n to formats where appropriate.
Typo "it it" correction.
Add #define pr_fmt where appropriate.
Remove function tracing logging messages.
Remove OOM messages.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:39 +02:00
Joe Perches
073a625f0b NFC: Convert nfc_dev_info and nfc_dev_err to nfc_<level>
Use a more standard kernel style macro logging name.

Standardize the spacing of the "NFC: " prefix.
Add \n to uses, remove from macro.
Fix the defective uses that already had a \n.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:39 +02:00
Joe Perches
b48348395f NFC: Replace nfc_dev_dbg with dev_dbg
Use the generic kernel function instead of a home-grown
one that does the same thing.

Add \n to uses not at the macro.  Don't add \n where
the nfc_dev_dbg macro mistakenly had them already.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:39 +02:00
Arron Wang
3943826177 NFC: pn544: Add SE enable/disable operation
To enable the UICC secure element, we first enable the UICC gate list in
order for the SE to be able to use all RF technologies.
For the embedded SE, we just turn the eSE default mode to ON.

Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:39 +02:00
Arron Wang
5faba2fdf9 NFC: pn544: Add SE discover operation
For the SWP secure element, we send the proprietary SELF_TEST_SWP
command and check the response.
For the WI secure element, we simply try to switch to the default
embedded SE mode. If that works, it means we have an embedded SE.

Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-09-25 01:35:38 +02:00
Eric Lapuyade
06c660340f NFC: pn544: i2c: Add firmware download implementation for pn544
The pn544 can enter a firmware update mode where firmware blobs can be
pushed through the i2c line and flashed on the target.
A special command allows to verify that blobs are correctly flashed and
this is what we do for every downloaded firmware blob.

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-08-14 01:13:35 +02:00