This patch simplifies the required block count calculation. Though it
introduces a division operator, it greatly simplifies the formula.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses a higher precision timer to synchronize with the firmware
clock. Improved precision is needed as on some platforms a jiffy may be up to
tens of milliseconds, and the required precision is closer to TU's.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements looped IRQ handling. In essence, if a new interrupt is
asserted by the FW while the host is processing the previous one, the host
will directly proceed processing the new IRQ without leaving the handling
function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mask firmware interrupts while processing interrupts. This allows the
interrupt handler looping to work efficiently thus reducing interrupt
processing latency.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will ack RX frames read from the firmware in one single write,
instead of acking all the frames separately. This will reduce the amount of
required communication per frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the annoying and dmesg-flooding WLAN PSM entry/exit traces. Instead,
only output them if PSM traces are enabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue stopping/waking functionality was broken in a way that could
cause huge latencies in TX transfers and even cause the TX to stall in the
right circumstances. Correct these problems.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ad-hoc mode preventing mac80211 from properly
detecting other ad-hoc networks with the same SSID.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Fix a TX result overflow problem that was present in the TX path and visible
with at least linksys AP's (probably any AP with high throughput capability.)
- Optimize TX by writing FW trigger for a group of TX frames instead of
each and every frame.
- Slightly optimize the TX path code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most probably patch "wl1271: add most of the normal initialization commands
to PLT mode" enabled the RX path in firmware so that now driver received
frames and passed them to mac80211, which warned about them.
Workaround this by not retrieving frames from the hardware, just ignore them.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed two bugs causing problems when unloding wl1271 module. First was
missing sdio_set_drvdata call from the probe function, second was order
of function calls in the remove function.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed access to fw status register to use raw read instead of
translated addressing. On SDIO access by translated addressing was not
working and raw access is working also on SPI.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added initial implementation of SDIO interfacte to the wl1271 driver.
When selected, this adds new module called "wl1271_sdio".
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Divided wl1271 driver to wl1271 "core" and wl1271_spi modules in preparation
of integration of the SDIO implementation.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed wl1271_spi.h header as there's no more need to access functions
declared there outside of wl1271_spi.c. Also made those SPI access
functions static.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed the driver to use if_ops structure to abstract access to the IO
layer (SPI or SDIO).
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved wl1271 drivers probe, remove etc. functions and structres to
wl1271_spi.c from wl1271_main.c in preparation of implementing SDIO interface.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
P54 devices always generate a full tx_status report
(ACK, PSM, rate control, etc..) for every xmitted frame.
Therefore, I think The driver qualifies for the
REPORTS_TX_ACK_STATUS hardware feature flag.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_hw_register_timeout() was duplicated between phy.c and reset.c.
Since it is too big and too much used to be an inline function, move it
away from the ath5k.h header into reset.c. Remove _ATH5K_RESET and
_ATH5K_PHY defines.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust formatting of the affected lines to satisfy checkpatch.pl.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all unnecessary function declarations from ath5k.h. Comment out
unused functions. Remove ath5k_hw_get_tsf32(), which is too trivial to
be commented out. Make functions static if suggested by sparse. Make
ath5k_pm_ops static.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise value as is won't be used, isn't
filled by most drivers and doesn't really
make a whole lot of sense on a per packet
basis -- proper cfg80211 survey support in
mac80211 will need to be different.
Mark the struct member as deprecated so it
will be removed from drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export rt2x00soc_probe from rt2x00soc as it is used in rt2800pci.
Otherwise loading rt2800pci gives "rt2800pci: Unknown symbol
rt2x00soc_probe".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the wireless summit in Portland we discussed a way of
loading firmware asynchronously from ->probe() before
registration to mac80211, in order to register with the
wireless subsystems with complete information in cases
where firmware is required to know parameters.
This is not yet the case in iwlwifi, but for some new
features we're working on it will be the case since
those will only be supported by new firmware images.
Hence, to start with, convert iwlwifi to load firmware
asynchronously from probe, unbinding the device when
firmware loading fails, and only registering with the
wireless subsystems after firmware has been loaded
successfully.
Future patches will hook into this to register the
new firmware capabilities, depending on the firmware
API version.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ar9170 to load firmware asynchronously
out of ->probe() and only register with mac80211 when
all firmware has been loaded successfully. If, on the
other hand, any firmware fails to load, it will now
unbind from the device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compiling rt2800pci with CONFIG_RT2800PCI_SOC fails with "... rt2880pci.c:
error: incompatible type for argument 2 of 'rt2x00soc_probe'".
Fix this by using &rt2800pci_ops instead of rt2800pci_ops.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for CEIVA USB wireless adapters to the rt73usb driver.
Signed-off-by: Bryan Polk <sainth@eidolons.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e1dd33f60ced091114e4aacf141e0d03b88d3e13 changed cfg80211 to
allow association commands while in associated state to enable support
for roaming within an ESS. However, this was not enough to resolve all
cases with mac80211 which needs some additional handling of the
reassociation case to clear internal state with the BSS that was in use
previously.
This patch makes ieee80211_mgd_assoc() accept a valid reassociation
command and clean the association state with the previous BSS. This
fixes roaming between BSSes in an ESS when using wpa_supplicant with
-Dnl80211.
Signed-off-by: Jouni Malinen <j@w1.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first chunk fixes a debugging assert to print a warning about array underflows.
The second chunk corrects a potential array underflow. I also removed an assert
in the second chunk because it can no longer happen.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for handling KEY_RFKILL in the rfkill input module. This
simply toggles the state of all rfkill devices. The comment in rfkill.h
is also updated to reflect that RFKILL_TYPE_ALL may be used inside the
kernel.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if keylen == 0 is a bug and should not really happen, better avoid
possibility of passing bad value to firmware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is no longer needed. I missed to remove this in
567ec874d1 ("net: convert multiple
drivers to use netdev_for_each_mc_addr, part6")
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sis190 devices don't report LinkChange, so do polling for
link status.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11926
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e992cd9b72 (kmemcheck: make bitfield annotations truly no-ops
when disabled) allows us to revert a workaround we did in the past to
not add holes in sk_buff structure.
This patch partially reverts commit 14d18a81b5
(net: fix kmemcheck annotations) so that sparse doesnt complain:
include/linux/skbuff.h:357:41: error: invalid bitfield specifier for
type restricted __be16.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build error when IGMP_SNOOPING is not enabled.
In file included from net/bridge/br.c:24:
net/bridge/br_private.h: In function 'br_multicast_is_router':
net/bridge/br_private.h:361: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:362: error: 'struct net_bridge' has no member named 'multicast_router'
net/bridge/br_private.h:363: error: 'struct net_bridge' has no member named 'multicast_router_timer'
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Resending with the proper subject. Sorry for the mess. ]
This patch is based on the RFC of Stanislaw Gruszka.
More specifically it fixes two possible races:
- One, described by Stanislaw, may lead to permanent disabling of the Tx
queue.
This is fixed by adding the smp_wmb() to propagate the BD consumer
change towards the memory.
- Second may lead to bnx2x_start_xmit() returning NETDEV_TX_BUSY.
This is fixed by taking a tx_lock() before rechecking the number of
available Tx BDs.
thanks,
vlad
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use scm_send and scm_recv on both unix domain and
netlink sockets, but only unix domain sockets support
everything required for file descriptor passing,
so error if someone attempts to pass file descriptors
over netlink sockets.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, uv: Remove recursion in uv_heartbeat_enable()
x86, uv: uv_global_gru_mmr_address() macro fix
x86, uv: Add serial number parameter to uv_bios_get_sn_info()
* 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Enable NMI on all cpus on UV
vgaarb: Add user selectability of the number of GPUS in a system
vgaarb: Fix VGA arbiter to accept PCI domains other than 0
x86, uv: Update UV arch to target Legacy VGA I/O correctly.
pci: Update pci_set_vga_state() to call arch functions
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: Don't skip mode setting for the standard VGA modes
x86-64, setup: Inhibit decompressor output if video info is invalid
x86, setup: When restoring the screen, update boot_params.screen_info
* 'x86-rwsem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-64, rwsem: Avoid store forwarding hazard in __downgrade_write
x86-64, rwsem: 64-bit xadd rwsem implementation
x86: Fix breakage of UML from the changes in the rwsem system
x86-64: support native xadd rwsem implementation
x86: clean up rwsem type system
* 'x86-numa-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, numa: Remove configurable node size support for numa emulation
x86, numa: Add fixed node size option for numa emulation
x86, numa: Fix numa emulation calculation of big nodes
x86, acpi: Map hotadded cpu to correct node.
* 'x86-mtrr-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Convert set_atomicity_lock to raw_spinlock
x86, mtrr: Kill over the top warn
x86, mtrr: Constify struct mtrr_ops
