Commit Graph

22 Commits

Author SHA1 Message Date
Andi Kleen
f271a6f557 [PATCH] x86_64: Removed duplicated declaration of force_iommu
Noticed by Andrew Morton.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-25 09:14:39 -08:00
Jan Beulich
86ebcea899 [PATCH] x86_64: remove dead do_softirq_thunk
Appearantly a left-over...

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-25 09:10:53 -08:00
Andi Kleen
e8b917775b [PATCH] x86_64: Move the SMP time selection earlier
SMP time selection originally ran after all CPUs were brought up because
it needed to know the number of CPUs to decide if it needs an MP safe
timer or not.

This is not needed anymore because we know present CPUs early.

This fixes a couple of problems:
 - apicmaintimer didn't always work because it relied on state that was
   set up time_init_gtod too late.
 - The output for the used timer in early kernel log was misleading
   because time_init_gtod could actually change it later.  Now always
   print the final timer choice

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-26 09:53:31 -08:00
Andi Kleen
e2c0388866 [PATCH] x86_64: Fix the additional_cpus=.. option
It didn't set up the CPU possible map early enough, so the
option didn't actually work.

Noticed by Heiko Carstens

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-26 09:53:30 -08:00
Andi Kleen
7fd67843b9 [PATCH] x86_64: Disable tsc when apicpmtimer is active
Otherwise it has no effect anyways.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-17 08:00:40 -08:00
Andi Kleen
0c3749c41f [PATCH] x86_64: Calibrate APIC timer using PM timer
On some broken motherboards (at least one NForce3 based AMD64 laptop)
the PIT timer runs at a incorrect frequency.  This patch adds a new
option "apicpmtimer" that allows to use the APIC timer and calibrate it
using the PMTimer.  It requires the earlier patch that allows to run the
main timer from the APIC.

Specifying apicpmtimer implies apicmaintimer.

The option defaults to off for now.

I tested it on a few systems and the resulting APIC timer frequencies
were usually a bit off, but always <1%, which should be tolerable.

TBD figure out heuristic to enable this automatically on the affected
systems TBD perhaps do it on all NForce3s or using DMI?

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-04 16:43:15 -08:00
Shaohua Li
0dd2ea9af8 [PATCH] x86_64: [PATCH] timer resume
At resume time, TSC's value or something similar might be changed a lot
against suspend time. This could make system gets a very big lost ticks.
See http://bugzilla.kernel.org/show_bug.cgi?id=5825

Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-04 16:43:13 -08:00
Andi Kleen
73dea47fae [PATCH] x86_64: Allow to run main time keeping from the local APIC interrupt
Another piece from the no-idle-tick patch.

This can be enabled with the "apicmaintimer" option.

This is mainly useful when the PIT/HPET interrupt is unreliable.
Note there are some systems that are known to stop the APIC
timer in C3. For those it will never work, but this case
should be automatically detected.

It also only works with PM timer right now. When HPET is used
the way the main timer handler computes the delay doesn't work.

It should be a bit more efficient because there is one less
regular interrupt to process on the boot processor.

Requires earlier bugfix from Venkatesh

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-04 16:43:13 -08:00
Andi Kleen
226d780909 [PATCH] x86_64: Define pmtmr_ioport to 0 when PM_TIMER is not available
Avoids some ifdef mess later.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-04 16:43:12 -08:00
Andi Kleen
737c5c3bde [PATCH] x86_64: Don't try to synchronize the TSC over CPUs on Intel CPUs at boot.
They already do this in hardware and the Linux algorithm
actually adds errors.

Cc: mingo@elte.hu
Cc: rohit.seth@intel.com

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-11 19:04:57 -08:00
Andi Kleen
3c02175113 [PATCH] x86_64: Fix compile error with !CONFIG_COMPAT
cpumask.h wasn't included implicitely into proto.h in this case.
Just move it over to smp.h

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-11 19:04:57 -08:00
Muli Ben-Yehuda
17a941d854 [PATCH] x86_64: Use function pointers to call DMA mapping functions
AK: I hacked Muli's original patch a lot and there were a lot
of changes - all bugs are probably to blame on me now.
There were also some changes in the fall back behaviour
for swiotlb - in particular it doesn't try to use GFP_DMA
now anymore. Also all DMA mapping operations use the
same core dma_alloc_coherent code with proper fallbacks now.
And various other changes and cleanups.

Known problems: iommu=force swiotlb=force together breaks
                needs more testing.

This patch cleans up x86_64's DMA mapping dispatching code. Right now
we have three possible IOMMU types: AGP GART, swiotlb and nommu, and
in the future we will also have Xen's x86_64 swiotlb and other HW
IOMMUs for x86_64. In order to support all of them cleanly, this
patch:

- introduces a struct dma_mapping_ops with function pointers for each
  of the DMA mapping operations of gart (AMD HW IOMMU), swiotlb
  (software IOMMU) and nommu (no IOMMU).

- gets rid of:

  if (swiotlb)
      return swiotlb_xxx();

- PCI_DMA_BUS_IS_PHYS is now checked against the dma_ops being set
This makes swiotlb faster by avoiding double copying in some cases.

Signed-Off-By: Muli Ben-Yehuda <mulix@mulix.org>
Signed-Off-By: Jon D. Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-11 19:04:55 -08:00
Siddha, Suresh B
f6c2e3330d [PATCH] x86_64: Unmap NULL during early bootup
We should zap the low mappings, as soon as possible, so that we can catch
kernel bugs more effectively. Previously early boot had NULL mapped
and didn't trap on NULL references.

This patch introduces boot_level4_pgt, which will always have low identity
addresses mapped.  Druing boot, all the processors will use this as their
level4 pgt.  On BP, we will switch to init_level4_pgt as soon as we enter C
code and zap the low mappings as soon as we are done with the usage of
identity low mapped addresses.  On AP's we will zap the low mappings as
soon as we jump to C code.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-14 19:55:14 -08:00
Andi Kleen
a2f1b42490 [PATCH] x86_64: Add 4GB DMA32 zone
Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.

As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone.  We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.

But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.

So this patch adds both zones.

This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.

Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata).  They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices.  With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.

One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.

The new zone is so far added only for x86-64.

For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.

One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64  use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.

These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-14 19:55:13 -08:00
Jan Beulich
1209140c3c [PATCH] x86-64: Safe interrupts in oops_begin/end
Rather than blindly re-enabling interrupts in oops_end(), save their state
in oope_begin() and then restore that state.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-12 10:50:57 -07:00
Andi Kleen
b9aac10ddd [PATCH] x86-64: Remove redundant max_mapnr and replace with end_pfn
The FLATMEM people added it, but there doesn't seem a good reason
because end_pfn is identical.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-12 10:49:57 -07:00
Adrian Bunk
672289e9fa [PATCH] i386/x86_64: make get_cpu_vendor() static
get_cpu_vendor() no longer has any users in other files.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-09-10 10:06:35 -07:00
Shaohua Li
3b520b238e [PATCH] MTRR suspend/resume cleanup
There has been some discuss about solving the SMP MTRR suspend/resume
breakage, but I didn't find a patch for it.  This is an intent for it.  The
basic idea is moving mtrr initializing into cpu_identify for all APs (so it
works for cpu hotplug).  For BP, restore_processor_state is responsible for
restoring MTRR.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-07-07 18:23:42 -07:00
Andi Kleen
312df5f1a1 [PATCH] x86_64: Add pmtimer support
There are unfortunately more and more multi processor Opteron systems which
don't have HPET timer support in the southbridge.  This covers in particular
Nvidia and VIA chipsets.  They also don't guarantee that the TSCs are
synchronized between CPUs; and especially with MP powernow the systems are
nearly unusable because the time gets very inconsistent between CPUs.

The timer code for x86-64 was originally written under the assumption that we
could fall back to the HPET timer on such systems.  But this doesn't work
there.

Another alternative is to use the ACPI PM timer as primary time source.  This
patch does that.  The kernel only uses PM timer when there is no other choice
because it has some disadvantages.

Ported over from i386.  It should be faster than the i386 version because I
dropped the "read three times" workaround, but is still considerable slower
than HPET and also does not work together with vsyscalls which have to be
disabled.

Cc: <mark.langsdorf@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-05-17 07:59:15 -07:00
Andi Kleen
a8ab26fe5b [PATCH] x86_64: Switch SMP bootup over to new CPU hotplug state machine
This will allow hotplug CPU in the future and in general cleans up a lot of
crufty code.  It also should plug some races that the old hackish way
introduces.  Remove one old race workaround in NMI watchdog setup that is not
needed anymore.

I removed the old total sum of bogomips reporting code.  The brag value of
BogoMips has been greatly devalued in the last years on the open market.

Real CPU hotplug will need some more work, but the infrastructure for it is
there now.

One drawback: the new TSC sync algorithm is less accurate than before.  The
old way of zeroing TSCs is too intrusive to do later.  Instead the TSC of the
BP is duplicated now, which is less accurate.

akpm:

- sync_tsc_bp_init seems to have the sense of `init' inverted.

- SPIN_LOCK_UNLOCKED is deprecated - use DEFINE_SPINLOCK.

Cc: <rusty@rustcorp.com.au>
Cc: <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16 15:25:19 -07:00
Andi Kleen
1e01441051 [PATCH] x86_64: Use a VMA for the 32bit vsyscall
Use a real VMA to map the 32bit vsyscall page

This interacts better with Hugh's upcomming VMA walk optimization
Also removes some ugly special cases.

Code roughly modelled after the ppc64 vdso version from Ben Herrenschmidt.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16 15:24:55 -07:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00