The normal Thumb singlestepping routine updates the IT state after
calling the instruction handler. We don't what this to happen after the
IT instruction simulation sets the IT state, therefore we need to
provide a custom singlestep routine.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These instructions are equivalent to
stmdb sp!,{r0-r7,lr}
ldmdb sp!,{r0-r7,pc}
and we emulate them by transforming them into the 32-bit Thumb
instructions
stmdb r9!,{r0-r7,r8}
ldmdb r9!,{r0-r7,r8}
This is simpler, and almost certainly executes faster, than writing
simulation functions.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Most of these instructions only operate on the low registers R0-R7
so they can make use of t16_emulate_loregs_rwflags.
The instructions which use SP or PC for addressing have their own
simulation functions.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These data-processing instructions operate on the full range of CPU
registers, so to simulate them we have to modify the registers used
by the instruction. We can't make use of the decoding table framework to
do this because the registers aren't encoded cleanly in separate
nibbles, therefore we need a custom decode function.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These instructions only operate on the low registers R0-R7, therefore
it is possible to emulate them by executing the original instruction
unaltered if we restore and save these registers. This is what
t16_emulate_loregs does.
Some of these instructions don't update the PSR when they execute in an
IT block, so there are two flavours of emulation functions:
t16_emulate_loregs_{noit}rwflags
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
For hints which may have observable effects, like SEV (send event), we
use kprobe_emulate_none which emulates the hint by executing the
original instruction.
For NOP we simulate the instruction using kprobe_simulate_nop, which
does nothing. As probes execute with interrupts disabled this is also
used for hints which may block for an indefinite time, like WFE (wait
for event).
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
When a probe fires we must single-step the instruction which was
replaced by a breakpoint. As the steps to do this vary between ARM and
Thumb instructions we need a way to customise single-stepping.
This is done by adding a new hook called insn_singlestep to
arch_specific_insn which is initialised by the instruction decoding
functions.
These single-step hooks must update PC and call the instruction handler.
For Thumb instructions an additional step of updating ITSTATE is needed.
We do this after calling the handler because some handlers will need to
test if they are running in an IT block.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Extend arch_prepare_kprobe to support probing of Thumb code. For
the actual decoding of Thumb instructions, stub functions are
added which currently just reject the probe.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
