Mostly clean up CONFIG_OMAP_RESET_CLOCKS. Also includes a
patch from Imre Deak to make McSPI clocks use id.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch syncs OMAP DMA code with linux-omap tree.
Mostly allow changing DMA callback function and set
OMAP2 specific transfer mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some peripherals seem to need additional delay until they
can actually be accessed after enabling their FCLK and ICLK.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling and disabling the 54 MHz and 96 MHz APLLs can happen
unnecessarily often during bootup. Make sure they're kept
enabled during init.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP2420, an incoming GPIO interrupt always sets both GPIO_IRQSTATUS1
and GPIO_IRQSTATUS2, even if the relevant bit is disabled in
GPIO_IRQENABLE1/2 and DSP doesn't use GPIO at all. GPIO_IRQSTATUS1
is for MPU and GPIO_IRQSTATUS2 is for DSP. If IRQSTATUS is set, this
will prevent the system from going to idle state. This patch also clears
IRQSTATUS2 to avoid the above situation.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPT1 will be set into non-posted mode, and the wakeup register
is set for all timers.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some boards might use the oscillator clock for powering
external peripherals. Add support for making sure osc_ck
stays active even when trying to go to sleep.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add enable/disable functions which effectively control the GPT iclk and fclk.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove Remove superfluous/recursive locking for GPIO
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM11 can't access the IVA interrupt controller from
IVA slave port.
From Richard Woodruff:
"The 0x40000000 is an IVA-ARM7 local bus address.
The IVA-INTC is NOT accessible through the IVA-L3-Slave Port.
The current TRM does say this directly and indirectly in a few spots and
in figures."
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After adjusting clock parameters, OMAP2 CPUs need a memory
barrier to make sure the changes go into effect immediately.
Otherwise bad things will happen if we try to access the
peripheral whose clock is just being enabled.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A forgotten parenthesis in clock.c caused the PLL stabilization loop
to not be executed correctly.
Signed-off-by: Samuel Ortiz <samuel.ortiz@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes the OMAP2 dmtimers module using the interface
clocks only while the registers are accessed (except GPT1 which has
iclk enabled all the time).
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for assigning memory regions dynamically to peripherals
attached to GPMC interface. Platform specific code should now call
gpmc_cs_request to get a free GPMC memory region instead of using
a fixed address.
Make the H4 and Apollon platform initialization use the new API.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The recent MPUIO range change fix breaks compilation if
CONFIG_ARCH_OMAP24XX isn't defined; it should be OMAP_MAX_GPIO_LINES not
MAX_GPIO_LINES I believe. This one liner fixes it.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds pin mux info for the SPI master/slave interface on
OMAP16xx. Data from OMAP 1611/1612 TRM and errata. Works for me on my
1611/H2 with current git kernel.
Signed-off-by: Mark Howell <mhowell@northlink.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have to make sure that the LCD DMA external destination bit is
cleared by default, otherwise OMAP won't sleep.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- MPUIO doesn't exist on OMAP2
- no error was returned for too big MPUIO numbers
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP does not need sys_ck or sys_clkout. If the devices connected
to McBSP need sys_clkout, they need to request it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Apollon board MMC supports on OMAP2
TODO:
We have to check MMC on H4
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reprogramming takes places before putting the CPU into idle mode if
the dynamic tick option is enabled. The timer is then set to expire
at the next pending timer event. Because some time has already passed
since the last reported jiffy we have to wait less than the time
specified in jiffies.
Also make sure we don't set a load value of 0 whose outcome is
unspecified according to the TRM.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds support for CONFIG_DEBUG_ICEDCC for ARM11.
Tested on ARM1136 (OMAP2420).
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Document the meaning for OP_SCALAR, OP_SD and add OP_DD.
- Formatting cleanups
- Remove now redundant code for making compare instructions
operate on scalar values.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VECITR in Floating-Point Exception register indicates the number of
remaining short vector iterations after a potential exception was
detected.
In case of exception caused by scalar instructions, VECITR is NOT updated.
Therefore emulation for VFP must ignore VECITR field
and treat "veclen" as zero when recognizing scalar instructing.
Signed-off-by: Gen Fukatsu <fukatsu.gen@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The documentation for the ZBOOT_ROM_BSS config option describes it as
"The base address of 64KiB of read/write memory in the target for the
ROM-able zImage..." In actuality, it requires more than 100 KiB of
space in addition to enough space to hold the decompressed kernel.
This patch fixes the description in the Kconfig file.
Signed-off-by: Dan Fandrich <dfandrich@intrinsyc.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix thinko in the flush_ptrace_access() "if (expr)" for the ARM
VIPT non-aliasing cache case. We only need to flush cache when
VM_EXEC is set in vma->vm_flags but "if (expr) always evaluates
to true on UP systems for the ARM VIPT non-aliasing cache case.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the IO-Data GLAN Tank, from Martin Michlmayr.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Thecus n2100 (80219-based.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the redundant Modification lines from
the top of the files in arch/arm/mach-s3c2410
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 LCD controller is different enough
to warrant renaming the platform device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add new machine VSTMS
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linuxtronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the old per-board defconfigs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add one defconfig for all iop32x boards and one defconfig for all
iop33x boards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the iop32x code isn't iop321-specific, and the iop33x code isn't
iop331-specfic, do a s/iop321/iop32x/ and s/iop331/iop33x/, and tidy up
the code to conform to the coding style guidelines somewhat better.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Revamp the iop3xx board support: move the support code for each iop
board type into its own file, start using platform serial and platform
physmap flash devices, switch to a per-board time tick rate, and get
rid of the ARCH_EP80219 and STEPD config options by doing the relevant
checks at run time.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Squeeze three instructions out of the iop32x irq demuxer, and nine
out of the iop33x irq demuxer by using the hardware vector generator.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The iop33x loadsp hunk in arch/arm/boot/compressed/head.S serves
no purpose -- remove it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the gpio_line_{config,get,set} API for iop3xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the unused IOP3??_IRQ_OFS irq offset define, start IRQ
numbering from zero.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add CP6 enable/disable sequences to the timekeeping code and the IRQ
code. As a result, we can't depend on CP6 access being enabled when
we enter get_irqnr_and_base anymore, so switch the latter over to
using memory-mapped accesses for now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the iop32x and iop33x code over to the common time implementation,
and remove the (nearly identical) iop32x and iop33x time implementations.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge and rewrite the iop32x/iop33x time code to do lost jiffy
tracking properly, and put the result in plat-iop/time.c.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the iop32x and iop33x code over to the common PCI implementation,
and remove the (nearly identical) iop32x and iop33x PCI implementations.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge the iop32x PCI code and iop33x PCI code into plat-iop/pci.c.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the i2c bits shared between iop32x and iop33x to plat-iop/i2c.c
and include/asm-arm/hardware/iop3xx.h.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce the arch/arm/plat-iop directory, for code shared between the
iop32x and iop33x, and move the common memory map setup bits there.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename CONFIG_ARCH_IOP321 to CONFIG_ARCH_IOP32X and
CONFIG_ARCH_IOP331 to CONFIG_ARCH_IOP33X.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clear both the EINT and INT status before
going to sleep, otherwise we may end up being
woken by something that was not set in our
wakeup map.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c24xx_va_gpio2 variable is only used
when the S3C2412 and another cpu-type is
being used in the kernel. This patch ensures
it is not set when it is not being used.
Fixes bug report by Thomas Gleixner.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the S3C2410 specific items out of the
core PM code. Add sysdev driver for all the
S3C24XX series that used the S3C2410 PM code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On stepping A0/A1 of the 80200, invalidating D-cache by line doesn't
clear the dirty bits, which means that if we invalidate a dirty line,
the dirty data can still be written back to memory later on.
To work around this, dma_inv_range() on these two processors is
implemented as dma_flush_range() (i.e. do a clean D-cache line before
doing the invalidate D-cache line.) For this, we currently have a
processor ID check in xscale_dma_inv_range(), but a better solution
is to add a separate cache_fns and proc_info for A0/A1 80200.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prevent userland from mapping in physical address regions >= 4G by
checking for that in valid_mmap_phys_addr_range().
Unfortunately, we cannot override valid_mmap_phys_addr_range() without
also overriding valid_phys_addr_range(), so copy drivers/char/mem.c's
version of valid_phys_addr_range() over to arch/arm/mm/mmap.c as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change to using flush_cache_all() in pm.c and
also remove the need to flush the cache in the
PM code.
This changes the sleep.S code to have an entry
to store the registers for resume, and then a
second entry (after the caches are cleaned)
to do the suspend and resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Seperate the IRQ power management code out of
the pm.c file, and add it to the relevant
system class devices.
Also make the suspend and resume code take
notice of the fact these registers can be
moved by compile time code.
Add fix from Ilya Yanok to also save the
INTSUBMSK over sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow each CPU type in the S3C24XX range to
select the DMA channel mapping it supports.
We change the DMA registration to use an
virtual channel number that the DMA system
will allocate to a hardware channel at
request time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The ARM kernel has several uses of asm("foo%?"). %? is a GCC internal
modifier used to output conditional execution predicates. However, no
version of GCC supports conditionalizing asm statements. GCC 4.2 will
correctly expand %? to the empty string in user asms. Earlier versions may
reuse the condition from the previous instruction. In 'if (foo) asm
("bar%?");' this is somewhat likely to be right... but not reliable.
So, the only safe thing to do is to remove the uses of %?. I believe
the tlbflush.h occurances were supposed to be removed before, based
on the comment about %? not working at the top of that file.
Old versions of GCC could omit branches around user asms if the asm didn't
mark the condition codes as clobbered. This problem hasn't been seen on any
recent (3.x or 4.x) GCC, but it could theoretically happen. So, where
%? was removed a cc clobber was added.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The common case for the thread notifier is a context switch. Tell
gcc that this is the most likely condition so it can optimise the
function for this case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename mmu.c to context.c - it's the ARMv6 ASID context handling
code rather than generic "mmu" handling code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move top_pmd into arch/arm/mm/mm.h - nothing outside arch/arm/mm
references it.
Move the repeated definition of TOP_PTE into mm/mm.h, as well as
a few function prototypes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Do not define set_irq_wake as a real function if
the CONFIG_PM option is not set.
Fixes bug reported by Thomas Gleixner.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dan Williams
commit a6a38a6622 changed the iop321 id to a value that does not work with all platforms. Change the mask to permit bit 11. Tested on an iq80321 600Mhz CRB.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the idle code on the s3c2412 as the default
code is using bits in the CLKCON register that are
no-longer there.
Provide an override for the idle code, and ensure
that the power configuration is set to allow idle
instead of stop or sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
These two machines are identical, and supported
by the SMDK2413 configuration. When MACH_SMDK2413
is selected, we must also select MACH_S3C2413
to allow machine_is_smdk2413() or machine_is_s3c2413()
to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The IRQ_EINT0 through IRQ_EINT3 handling has changed
on the S3C2412 from the previous SoCs in the range,
and thus we need to add code to handle this.
The changes come about due to these IRQs being
displayed in two different registers, and needing to
be acked and masked in both.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The s3c244x-irq.c code makes the mistake of adding
the same drive to two different sys-classes. This
causes the class lists to become corrupted and the
suspend code to OOPS.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
It turns out we have both SMDK2413 and S3C2413 for
the same board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The ARM926EJ-S CPU has the VFP coprocessor and therefore it should be shown
in the /proc/cpuinfo if CONFIG_VFP is enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Include linux/irq.h in the nslu2 code in order to avoid the following
compiler error:
CC arch/arm/mach-ixp4xx/nslu2-power.o
arch/arm/mach-ixp4xx/nslu2-power.c: In function 'nslu2_power_init':
arch/arm/mach-ixp4xx/nslu2-power.c:53: warning: implicit declaration of function 'set_irq_type'
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: 'IRQ_TYPE_LEVEL_LOW' undeclared (first use in this function)
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: (Each undeclared identifier is reported only once
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: for each function it appears in.)
arch/arm/mach-ixp4xx/nslu2-power.c:54: error: 'IRQ_TYPE_LEVEL_HIGH' undeclared (first use in this function)
make[5]: *** [arch/arm/mach-ixp4xx/nslu2-power.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Remove the pointless changelog comments from
arch/arm/mach-s3c2410 files, as all this can
be found from the revision control system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
Resolve ARM1136 VIPT non-aliasing cache coherency issues observed when
using ptrace to set breakpoints and cleanup copy_{to,from}_user_page()
while we're here as requested by Russell King because "it's also far
too heavy on non-v6 CPUs".
NOTES:
1. Only access_process_vm() calls copy_{to,from}_user_page().
2. access_process_vm() calls get_user_pages() to pin down the "page".
3. get_user_pages() calls flush_dcache_page(page) which ensures cache
coherency between kernel and userspace mappings of "page". However
flush_dcache_page(page) may not invalidate I-Cache over this range
for all cases, specifically, I-Cache is not invalidated for the VIPT
non-aliasing case. So memory is consistent between kernel and user
space mappings of "page" but I-Cache may still be hot over this
range. IOW, we don't have to worry about flush_cache_page() before
memcpy().
4. Now, for the copy_to_user_page() case, after memcpy(), we must flush
the caches so memory is consistent with kernel cache entries and
invalidate the I-Cache if this mm region is executable. We don't
need to do anything after memcpy() for the copy_from_user_page()
case since kernel cache entries will be invalidated via the same
process above if we access "page" again. The flush_ptrace_access()
function (borrowed from SPARC64 implementation) is added to handle
cache flushing after memcpy() for the copy_to_user_page() case.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The type naming in the s3c24xx dma code is riddled with
typedefs creating _t types, from the code import from 2.4
which is contrary to the current Kernel coding style.
This patch cleans this up, removing the typedefs and
and fixing up the resultant code changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
This adds RTC support to the csb337 default config. Both the AT91
and the ds1307 RTCs are enabled (rtc0 and rtc1 respectively).
The ds1307 is used to initialize the system time, since it's battery-backed.
From then on the AT91 RTC is used, since it's more capable (with both
alarm and update irqs, and system wakeup capability) even though it
needs manual initialization (symlink /dev/rtc to /dev/rtc0 for older
versions of hwclock, then "hwclock --systohc") in an rc script or
from inittab.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
vfp_put_double didn't work in a CONFIG_AEABI kernel. By swapping
the arguments, we arrange for them to be in the same place regardless
of ABI. I made the same change to vfp_put_float for consistency.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On armv4t systems, we have always compiled the kernel with -march=armv4
instead of -march=armv4t, which means that any use of bx will bomb out.
Commit ba9b5d7637 introduced the use of
bx in the kernel, which means we need to compile with -march=armv4t on
armv4t systems now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the necessary call to register_isa_ports() so that glibc knows
where these are found on Integrator platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
Remove buld warning when building sa1111 on non-sa1100 platforms (e.g. PXA).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Paul Sokolovsky
This patch adds timeouts while working with SSP registers. Such
timeouts were envisioned by docstrings in ssp.c, but were not
implemented. There were actual lockups while accessing
touchscreen for iPaqs h1910, h4000 due to lack of the timeouts.
This is updated version of previously submitted patch: 3738/1.
Signed-off-by: Paul Sokolovsky <pmiscml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The fcvtds and fcvtsd instructions were generating a qnan bit pattern
for both quiet and signalling NaNs.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The fcvtsd/fcvtds emulation was left behind when the numbering of double
precision registers was changed from 0-30 to 0-15. Both conversion
instructions were writing their results to the wrong register. Also,
the conversion instructions should stop after the first element even
if a vector length is specified.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The recent fix to hide VFP_NAN_FLAG broke the check in vfp_raise_exceptions;
it would attempt to deliver an exception mask of 0xfffffeff instead of reporting
a serious error condition using printk. Define a safe constant to use for
an invalid exception maskm, and use it at both ends.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The userspace helpers in clean/arch/arm/kernel/entry-armv.S are called
directly in/from userspace. They need to cope with being called from
Thumb code.
Patch below uses the bx interworking instruction when
CONFIG_ARM_THUMB=y.
Based on an earlier patch from Paul Brook <paul@codesourcery.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This is instead of a magic number.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Kevin Hilman
Previous locking changes to dmabounce incorrectly return non-NULL even
when buffer not found. Fix it up.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
tidy up the makefile by using TABs to indent, and ensure
that all items are indented the same.
Move the DMA to its own section, ready for the next set
of updates
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
A number of small issues with the S3C24XX DMA have
cropped up, which this patch fixes. These are:
- check wether we can load another buff in start
- update state handling in s3c2410_dma_lastxfer
- only reload in irq if channel is not idle
- more informative timeout errors (add source)
- do not call request_irq() with irqs locked
- added waitforstop function
The patch also adds a S3C2410_DMAOP_STARTED for
the occasions when the driver wants to ensure that
the DMA system load state is resynced after loading.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previously the message was "Fatal exception: panic_on_oops", as introduced
in a recent patch whith removed a somewhat dangerous call to ssleep() in
the panic_on_oops path. However, Paul Mackerras suggested that this was
somewhat confusing, leadind people to believe that it was panic_on_oops
that was the root cause of the fatal exception. On his suggestion, this
patch changes the message to simply "Fatal exception". A suitable oops
message should already have been displayed.
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Yoav Steinberg
Flash resource mapping for versatile machine included one extra byte for the end address. This results in failure to map other resources on physical address directly after the NOR flash.
Signed-off-by: Yoav Steinberg <yoav@monfort.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Fix the following compilation error in arm/mach-ixp4xx/gtwx5715-setup:
CC arch/arm/mach-ixp4xx/gtwx5715-setup.o
arch/arm/mach-ixp4xx/gtwx5715-setup.c:110: error: expected identifier or '(' before = token
arch/arm/mach-ixp4xx/gtwx5715-setup.c:121: error: 'gtwx5715_flash_resource' undeclared here (not in a function)
arch/arm/mach-ixp4xx/gtwx5715-setup.c: In function 'gtwx5715_init':
arch/arm/mach-ixp4xx/gtwx5715-setup.c:133: error: 'flash_resource' undeclared (first use in this function)
arch/arm/mach-ixp4xx/gtwx5715-setup.c:133: error: (Each undeclared identifier is reported only once
arch/arm/mach-ixp4xx/gtwx5715-setup.c:133: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-ixp4xx/gtwx5715-setup.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
Fix "WARNING: "rtc_next_alarm_time" [drivers/rtc/rtc-sa1100.ko]
undefined!"
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
ARM genirq cleanups/updates:
- Start switching platforms to newer APIs
* use "irq_chip" name, not "irqchip"
* providing irq_chip.name
- Show irq_chip.name in /proc/interrupts, like on x86.
This update a bit more than half of the ARM code. The irq_chip.name
values were chosen to match docs (if I have them) or be otherwise
obvious ("FPGA", "CPLD", or matching the code).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is part of an effort to unify the panic_on_oops behaviour across
all architectures that implement it.
It was pointed out to me by Andi Kleen that if an oops has occured in
interrupt context, then calling sleep() in the oops path will only cause a
panic, and that it would be really better for it not to be in the path at
all.
This patch removes the ssleep() call and reworks the console message
accordinly. I have a slght concern that the resulting console message is
too long, feedback welcome.
For powerpc it also unifies the 32bit and 64bit behaviour.
Fror x86_64, this patch only updates the console message, as ssleep() is
already not present.
Signed-off-by: Horms <horms@verge.net.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Catalin Marinas
This patch adds #ifdef around some variables in the arch/arm/mm/ioremap.c
file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
As reported by various folks on the ARM Linux kernel mailing list,
the video-buf.ko driver has undefined references on all ARM machines
which use it as observed during `make modules`:
Warning: "v4wb_clear_user_page" [drivers/media/video/video-buf.ko] undefined!
Similar warnings exist for all ARM machines which use this driver.
So this change adds the missing EXPORT_SYMBOLs to allow using this
driver as a module.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The IOP 80219 xscale CPU is a stripped down version of the IOP32x.
But the fact that the 80219 and IOP32x are very similar doesn't mean
that they need to share a cpu table entry. It's also somewhat confusing
for the end user to see the 80219 reported as an IOP32x, so this patch
splits the IOP32x cpu table entry to make a separate entry for the
80219.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Remove unused IDE static mapping, now being ioremap()d
by the simtec IDE driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Tidy the syntax, such as missing ,'s on the end of
struct entries, in the Osiris and Anubis machines.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Processor support files now use r6 in their CPU setup code, so
we can't rely on r6 being preserved. Use r7 instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Since the ep93xx ohci bits are merged upstream now, enable ohci in
the ep93xx defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix more fallout from 894673ee61.
arch/arm/mach-footbridge/cats-hw.c: In function 'fixup_cats':
arch/arm/mach-footbridge/cats-hw.c:81: error: 'ORIG_VIDEO_LINES' undeclared (first use in this function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since this assignment was the only place on !alpha where isa_bridge was
touched, it didn't have any effect.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
Also warn users about charging in unsuitable temperature.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
It seems that sharp had charger on by default... This at least turns
it off. Also battery reading now works and is useful.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
The genirq conversion of ARM lost a CPU Hotplug helper function.
Restore it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
From: Dirk Opfer <Dirk@Opfer-Online.de>
Fix ucb initialization on collie. Wrong frequency was used and that
led to things not working quite correctly. (I had to actually disable
checks in my tree to get it to boot). It now includes all the
neccessary parts to get it to compile :-).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a configuration was chosen to support both the Versatile
AB and PB boards, the result would write to registers not
available on the PB version of the board. Resolve this by
using machine_is_xxx().
Also, for the CLCD, despite how the code looks, both the AB
and PB access the same location to control the clock rate -
it's just called something different between the two board
versions. Invent our own name for this location and use it
unconditionally.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
screen_info.h doesn't have anything to do with the tty layer and shouldn't be
included by tty.h. This patches removes the include and modifies all users to
directly include screen_info.h. struct screen_info is mainly used to
communicate with the console drivers in drivers/video/console. Note that this
patch touches every arch and I have no way of testing it. If there is a
mistake the worst thing that will happen is a compile error.
[akpm@osdl.org: fix arm build]
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Andrew Victor
The AIC interrupt controller is the same on the Atmel AT91RM9200,
AT91SAM9261 and AT91SAM9260 processors.
This patch removes any RM9200-specific naming from the IRQ driver, and
moves the AT91RM9200's default IRQ priority table into at91rm9200.c.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
Convert pnx4008 chip support to use generic irq subsystem
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No need for 'cr' to be a local variable, which is unused in the
SMP case, and only used once in the UP case. Just call get_cr()
directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Platforms which use ecard.c always have 32-bit resources, so
might as well lose the "long" format strings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ISA IRQ code was not using named initialisers, so merging the
64-bit resource code (which re-ordered the struct members) broke
this. Fix it up to use named initialisers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Commit ff0daca525 broke the SMP build,
this patch fixes it up again.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM devel merge introduced new machine functionality which was not
covered by the ARM -> genirq patches. Fix it up and make it compile
again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For several proc-<cputype>.S files the include of proc-macros.S is
missing. Make it compile and work again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The irgflags consolidation did conflict with the ARM to generic IRQ
conversion and was not applied for ARM. Fix it up.
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 3541/2: workaround for PXA27x erratum E7
[ARM] nommu: provide a way for correct control register value selection
[ARM] 3705/1: add supersection support to ioremap()
[ARM] 3707/1: iwmmxt: use the generic thread notifier infrastructure
[ARM] 3706/2: ep93xx: add cirrus logic edb9315a support
[ARM] 3704/1: format IOP Kconfig with tabs, create more consistency
[ARM] 3703/1: Add help description for ARCH_EP80219
[ARM] 3678/1: MMC: Make OMAP MMC work
[ARM] 3677/1: OMAP: Update H2 defconfig
[ARM] 3676/1: ARM: OMAP: Fix dmtimers and timer32k to compile on OMAP1
[ARM] Add section support to ioremap
[ARM] Fix sa11x0 SDRAM selection
[ARM] Set bit 4 on section mappings correctly depending on CPU
[ARM] 3666/1: TRIZEPS4 [1/5] core
ARM: OMAP: Multiplexing for 24xx GPMC wait pin monitoring
ARM: OMAP: Fix SRAM to use MT_MEMORY instead of MT_DEVICE
ARM: OMAP: Update dmtimers
ARM: OMAP: Make clock variables static
ARM: OMAP: Fix GPMC compilation when DEBUG is defined
ARM: OMAP: Mux updates for external DMA and GPIO
...
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Convert the files in arch/arm/common to use the generic
irq handling functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Switch the ARM irq core handling to the generic implementation. The
ARM specific header files now contain mostly migration stubs and
helper macros. Note that each machine type must be converted after
this step seperately. This was seperated out from the patch for easier
review.
The main changes for the machine type code is the conversion of the
type handlers to a 'type flow' and 'chip' model. This affects only the
multiplex interrupt handlers. A conversion macro needs to be added to
those implementations, which defines the data structure which is
registered by the set_irq_chained_handler() macro.
Some minor fixups of include files and the conversion of data
structure access is necessary all over the place.
The mostly macro based conversion was provided to allow an easy
migration of the existing implementations.
The code compiles on all defconfigs available in arch/arm/configs
except those which were broken also before applying the conversion
patches.
The code has been boot and runtime tested on most ARM platforms. The
results of an extensive testing and bugfixing series can be found
at: http://www.linutronix.de/index.php?page=testing
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
According to the Intel PXA27x Processor Family Specification
Update document (doc.nr. 280071-009) erratum E7, some care must be taken
to locate the disabling and re-enabling of the MMU to the beginning of a
cache line to avoid problems in some circumstances.
Credits to Simon Vogl <simon.vogl@researchstudios.at> for bringing this
up.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Analogous to the previous patch that allows ioremap() to use section
mappings, this patch allows ioremap() to use supersection mappings.
Original patch by Deepak Saxena.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch makes the iWMMXt context switch hook use the generic
thread notifier infrastructure that was recently merged in commit
d6551e884c.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus Logic EDB9315A, an evaluation
board based on the Cirrus Logic EP9315 SoC, with 64M RAM, two USB host
ports, audio in/out, three serial ports, 10/100 ethernet, and IDE, VGA,
and LCD interfaces.
The EDB9315A is a low-cost version of the EDB9315, and has only 16M
of NOR flash, while the EDB9315 has 32M.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Some cosmetic changes to increase the consistency of the IOP Kconfig file. Change some space into tabs and add a dot at the end of a help description.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Add a brief help description for ARCH_EP80219.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch makes OMAP MMC work again:
- Fix compile errors
- Do not ioremap base as it is already statically mapped
- Clean-up platform device handling
- Fix compile warnings
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP H2 defconfig and leave out hw random for now until
it's been updated.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Fixes compilation errors on OMAP1. Patch from Timo Teras.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conversion of nr_page_table_pages to a per zone counter
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow section mappings to be setup using ioremap() and torn down
with iounmap(). This requires additional support in the MM
context switch to ensure that mappings are properly synchronised
when mapped in.
Based an original implementation by Deepak Saxena, reworked and
ARMv6 support added by rmk.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid folk having to edit cpu-sa1110.c to select their RAM type;
instead, allow the SDRAM type to be selected via the kernel
command line.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
On some CPUs, bit 4 of section mappings means "update the
cache when written to". On others, this bit is required to
be one, and others it's required to be zero. Finally, on
ARMv6 and above, setting it turns on "no execute" and prevents
speculative prefetches.
With all these combinations, no one value fits all CPUs, so we
have to pick a value depending on the CPU type, and the area
we're mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Jrgen Schindele
This patch adds support for Trizeps4 SoM and ConXS-evalboard
from "Keith und Koep" This DIMM-module is based on PXA270.
Signed-off-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This prepares the way for adding support for the new Atmel AT91SAM926x
processors.
Major changes:
- Rename time.c to at91rm9200_time.c
- Rename common.c to at91rm9200.c
- Introduce ARCH_AT91, of which ARCH_AT91RM9200, ARCH_AT91SAM9260 and
ARCH_AT91SAM9261 are dependent.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus Logic EDB9302, an evaluation
board based on the Cirrus Logic EP9302 SoC, with 32M RAM, one USB host
port, audio in/out, two serial ports and a 10/100 ethernet interface.
George Kashperko submitted the original patch, this patch is a rewrite
using the newer physmap platform driver.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The bootloader on the LogicPD PXA270 platform informs the kernel of
which type of TFT screen is connected via an lcd=$FOO kernel command
line parameter.
Before this patch, we ignored this parameter and just hardcoded the use
of the Sharp lq64d343 display kit. This patch implement parsing of the
command line option, and chooses the right pxafb_mach_info to use (six
choices) based on this command line option.
Also fix the fb settings to correspond with those of the bootloader.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most MMU-based CPUs have a restriction on the setting of the data cache
enable and mmu enable bits in the control register, whereby if the data
cache is enabled, the MMU must also be enabled. Enabling the data
cache without the MMU is an invalid combination.
However, there are CPUs where the data cache can be enabled without the
MMU.
In order to allow these CPUs to take advantage of that, provide a
method whereby each proc-*.S file defines the control regsiter value
for use with nommu (with the MMU disabled.) Later on, when we add
support for enabling the MMU on these devices, we can adjust the
"crval" macro to also enable the data cache for nommu.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The "id(wb)BRR" suffix reports which CPU debugging options were (or
were not) selected at kernel build time. Rather than have every
proc-*.S file implement this, report the control register value,
from which this information can be deduced.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'nommu' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] nommu: backtrace code must not reference a discarded section
[ARM] nommu: Initial uCLinux support for MMU-based CPUs
[ARM] nommu: prevent Xscale-based machines being selected
[ARM] nommu: export flush_dcache_page()
[ARM] nommu: remove fault-armv, mmap and mm-armv files from nommu build
[ARM] Remove TABLE_SIZE, and several unused function prototypes
[ARM] nommu: Provide a simple flush_dcache_page implementation
[ARM] nommu: add arch/arm/Kconfig-nommu to Kconfig files
[ARM] nommu: add stubs for ioremap and friends
[ARM] nommu: avoid selecting TLB and CPU specific copy code
[ARM] nommu: uaccess tweaks
[ARM] nommu: adjust headers for !MMU ARM systems
[ARM] nommu: we need the TLS register emulation for nommu mode
The code in "1007:" is in the .fixup section, which in the mmuless
case is discarded. Since this code is referenced from the .text
section, it causes an link error. Move this code into the .text
section instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In noMMU mode, various of functions which are defined in mm/proc-*.S
is not valid or needed to be avoided. i.g. switch_mm is not needed,
just returns and this makes the I & D caches are valid which shows
great improvement of performance including task switching and IPC.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hyok says Intel Xscale is not currently supported by uCLinux.
Rather than adding #error statements to the Xscale support files
and causing !MMU+Xscale configurations to fail to build, prevent
Xscale-based machines from being selected in !MMU mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a trivial patch to export flush_dcache_page in mm/nommu.c.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove fault-armv.o, mmap.o and mm-armv.o from uclinux builds - these
are concerned with MMU-ful operations, and as such are redundant for
uclinux.
Since this also removes iotable_init() and iotable_init() is used
extensively in the platform support files, just make it a no-op.
Based upon a couple of patches by Hyok.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
TABLE_SIZE is never used in arch/arm/mm/init.c. create_memmap_holes(),
memtable_init, and setup_io_desc() no longer exist in the kernel.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
nommu doesn't require a complex flush_dcache_page implementation
like the MMU-ful CPUs do, so provide a simplified version in nommu.c
and omit flush.c from the build as appropriate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include Kconfig-nommu when MMU is not selected.
(This is part of a patch from Hyok.)
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
nommu doesn't have any form of remapping support, so ioremap, etc
become stubs which just return the casted address, doing nothing
else.
Move ioport_map(), ioport_unmap(), pci_iomap(), pci_iounmap()
into a separate file which is always built.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since uclinux doesn't make use of the TLB, including the TLB
maintainence and CPU-optimised copypage functions does not
make sense. Remove them.
(This is part of one of Hyok's patches.)
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MMUless systems have only one address space for all threads, so
both the usual access_ok() checks, and the exception handling do
not make much sense.
Hence, discard the fixup and exception tables at link time, use
memcpy/memset for the user copy/clearing functions, and define
the permission check macros to be constants.
Some of this patch was derived from the equivalent patch by
Hyok S. Choi.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since there can be no fixed location for the TLS value with nommu
systems, we must provide TLS register emulation in order to support
TLS binaries on CPUs without the thread register.
Part of a patch from Hyok S. Choi, and cleaned up by rmk.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Guennadi Liakhovetski
Currently probe_irq_on() on PXA will silently reconfigure all output GPIOs, that are not configured as alternate functions, for input. Avoid that. Upon CPU reset all GPIOs are configured as inputs, so, if a GPIO is configured as output, it has been done so intentionally.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus Logic EDB9315, an evaluation
board based on the Cirrus Logic EP9315 SoC, with 64M RAM, two USB host
ports, audio in/out, three serial ports, 10/100 ethernet, and IDE, VGA,
and LCD interfaces.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add the necessary kernel bits for crunch task switching.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch makes it possible to get/set a task's Crunch state via
the ptrace(2) system call.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch makes the kernel save Crunch state in userland signal frames,
so that any userland signal handler can safely use the Crunch coprocessor
without corrupting the Crunch state of the code it preempted.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The S3C2440 and S3C2442 have an extended USB gadget
controller, so re-name the platform device to inform
the driver that it needs to change some parameters
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Back in the days when we had armo (26-bit) and armv (32-bit) combined,
we had an additional layer to the uaccess macros to ensure correct
typing. Since we no longer have 26-bit in this tree, we no longer
need this layer, so eliminate it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With Goto-san's patch, we can add new pgdat/node at runtime. I'm now
considering node-hot-add with cpu + memory on ACPI.
I found acpi container, which describes node, could evaluate cpu before
memory. This means cpu-hot-add occurs before memory hot add.
In most part, cpu-hot-add doesn't depend on node hot add. But register_cpu(),
which creates symbolic link from node to cpu, requires that node should be
onlined before register_cpu(). When a node is onlined, its pgdat should be
there.
This patch-set holds off creating symbolic link from node to cpu
until node is onlined.
This removes node arguments from register_cpu().
Now, register_cpu() requires 'struct node' as its argument. But the array of
struct node is now unified in driver/base/node.c now (By Goto's node hotplug
patch). We can get struct node in generic way. So, this argument is not
necessary now.
This patch also guarantees add cpu under node only when node is onlined. It
is necessary for node-hot-add vs. cpu-hot-add patch following this.
Moreover, register_cpu calculates cpu->node_id by cpu_to_node() without regard
to its 'struct node *root' argument. This patch removes it.
Also modify callers of register_cpu()/unregister_cpu, whose args are changed
by register-cpu-remove-node-struct patch.
[Brice.Goglin@ens-lyon.org: fix it]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on an original patch from Ralf Baechle <ralf@linux-mips.org> and
Vivek Goyal <vgoyal@in.ibm.com>. This is needed in order to prepare for
changing the size of resources.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MT_MEMORY is needed in order to execute code in SRAM. Also
need to use section mapping.
Based on a patch by Richard Woodruff.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Initialize timer outside of spinlock to reduce the time the spinlock is held
- Do clk_get to the source clocks during initialization to avoid sleeping later
- New function to set counter register
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the mutex protecting the clock list is static, the list
itself should be too.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for omap24xx power domains and
allows suspend to work.
Please note that for some reason core power domain still
does not seem to idle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement basic support for General-Purpose Memory Controller
as found on OMAP2420.
Dynamic CS address space allocation still needs to be done.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dmtimer framework update broke 32 kHz timer as udelay() does not work
before system timer is started (and GPT1 should not be reset).
This also makes the GP timer use GPT1. This requires a fix in clock framework.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Port dmtimer framework to OMAP2.
Modify the dmtimers API to support setting of PWM configuration and prescaler.
Convert 32 kHz timer and GP timer to use the dmtimer framework.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap2_clk_set_rate: dif_off must use clk->rate_offset, not clk->src_off.
omap2_get_src_field: for the case CM_SYSCLKOUT_SEL1, val must be 2 for
96MHz and 3 for 54MHz.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register the 24xx McSPI device as an OMAP2 platform device. The driver
module and Kconfig option were merged already some time ago.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add bitbang SPI driver for Innovator 1510 touchscreen, using the new
framework. Compile-tested only.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform driver init-code required by the aic23-alsa driver to
omap-innovator.
Signed-off-by: Mika Laitio <lamikr@cc.jyu.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO IRQ mask was retrieved incorrectly in cases where we have a mask
register instead of an enable register. Also we should only return the
valid bits depending on the bank size.
This fixes a bug on 1510/1610 based OMAPs where GPIO IRQs are not
delivered.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix for re-using OMAP DMA channel with different transfer parameters.
Bits in the CCR register need to be cleaned as well in some cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Syncing the ads7846 code with mainstream means that the Mistral support
needs to include a callback to read the pendown state.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds core support for the TI F-Sample Board (OMAP 850).
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One of the recent merges from mainline removed the Amstrad Delta USB
support. This patch adds it back in; it's the same as was in
2.6.16-omap2.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- The current OMAP GPIO IRQ framework doesn't use the do_edge_IRQ,
do_level_IRQ handlers, but instead calls do_simple_IRQ. This
doesn't handle disabled interrupts properly, so drivers will
still get interrupts after calling disable_irq. The patch solves
this by respecting the irq_desc.disable_depth and irq_desc.running
counters. When one of these is non-zero the handler is not called,
the interrupt is masked and marked as pending. The pending interrupt
will be serviced when the running handler returns. This is according
to the same semantics as the standard do_edge_IRQ and do_level_IRQ
handlers have, so one day we should use them instead of do_simple_IRQ.
- Process only interrupts that are not masked. The ISR may contain
pending interrupts that are masked these shouldn't be processed.
- Move the bank IRQ unmasking out of the IRQ dispatch loop. If there
are further iterations we shouldn't unmask it if there are level
triggered interrupts pending.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the OSK/Mistral specific glue for the omap_uwire driver and
its ADS 7846 touchscreen. It also moves the lcd and keypad setup so
it's grouped with the other Mistral-specific setup code, and provides
comments about which switch maps to which reported key.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: trivial fixes in Makefile
kbuild: adding symbols in Kconfig and defconfig to TAGS
kbuild: replace abort() with exit(1)
kbuild: support for %.symtypes files
kbuild: fix silentoldconfig recursion
kbuild: add option for stripping modules while installing them
kbuild: kill some false positives from modpost
kbuild: export-symbol usage report generator
kbuild: fix make -rR breakage
kbuild: append -dirty for updated but uncommited changes
kbuild: append git revision for all untagged commits
kbuild: fix module.symvers parsing in modpost
kbuild: ignore make's built-in rules & variables
kbuild: bugfix with initramfs
kbuild: modpost build fix
kbuild: check license compatibility when building modules
kbuild: export-type enhancement to modpost.c
kbuild: add dependency on kernel.release to the package targets
kbuild: `make kernelrelease' speedup
kconfig: KCONFIG_OVERWRITECONFIG
...
Add backlight intensity control to the LOCOMO lcd/backlight driver using the
backlight class and add basic power management support.
This is a reimplementation and improvement of patches by John Lenz and Pavel
Machek
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lennert Buytenhek
This patch adds support for the Ajeco 1ARM Single Board Computer, a
VME form factor SBC based on the Atmel AT91 SoC, with 64M RAM, seven
serial ports, three ethernet ports, IDE, CF, USB host and device,
and S-Video/VGA out.--
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add the rest of the supported S3C24XX family to the
configuration selection for ARCH_S3C2410. This should
try and make it clearer for people trying to find the
S3C2440 or freinds where they can be found.--
Signed-off-by: Ben Dooks <ben-linux@fluff.org>Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add SMDK2413 to the list of the machines being
built for ARCH_S3C2410, thus ensursing our all
machines build has an representitive of the
S3C2412/S3C2413 CPU series--
Signed-off-by: Ben Dooks <ben-linux@fluff.org>Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Make CPU uppercase on the SMDK2440 KConfig entries--
Signed-off-by: Ben Dooks <ben-linux@fluff.org>Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Milan Svoboda
IXP4XX platform can happily live without pci bus. This patch modifies
Kconfig to support this option and modifies Makefile so pci only files
are compiled only when pci is really selected.
Patch is tested and ixdp465 runs fine with or without the pci bus.--
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>Signed-off-by: Deepak Saxena <dsaxena@plexity.net>Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- proper prototypes for the following functions:
- ctrl_alt_del() (in include/linux/reboot.h)
- getrusage() (in include/linux/resource.h)
- make the following needlessly global functions static:
- kernel_restart_prepare()
- kernel_kexec()
[akpm@osdl.org: compile fix]
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove VM_LOCKED before remap_pfn range from device drivers and get rid of
VM_SHM.
remap_pfn_range() already sets VM_IO. There is no need to set VM_SHM since
it does nothing. VM_LOCKED is of no use since the remap_pfn_range does not
place pages on the LRU. The pages are therefore never subject to swap
anyways. Remove all the vm_flags settings before calling remap_pfn_range.
After removing all the vm_flag settings no use of VM_SHM is left. Drop it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
