Commit Graph

32440 Commits

Author SHA1 Message Date
Linus Torvalds
2080cee435 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
    Yasevich.

 2) ns_capable() check in sock_diag netlink code, from Andrew
    Lutomirski.

 3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.

 4) Checksum offloading busted in sxgbe driver due to incorrect
    descriptor layout, fix from Byungho An.

 5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
    Lim.

 6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
    Starovoitov.

 7) Fix arch dependencies of candence driver.

 8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.

 9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
    IFLA_EXT_MASK, from David Gibson.

10) IPV6 FIB dump restart doesn't handle table changes that happen
    meanwhile, causing the code to loop forever or emit dups, fix from
    Kumar Sandararajan.

11) Memory leak on VF removal in bnx2x, from Yuval Mintz.

12) Bug fixes for new Altera TSE driver from Vince Bridgers.

13) Fix route lookup key in SCTP, from Xugeng Zhang.

14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
    driver.  From Oliver Hartkopp.

15) TCP doesn't bump retransmit counters in some code paths, fix from
    Eric Dumazet.

16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
    zero.  Fix from Liu Yu.

17) Fix locking imbalance in error paths of HHF packet scheduler, from
    John Fastabend.

18) Properly reference the transport module when vsock_core_init() runs,
    from Andy King.

19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.

20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
    ip_tunnel_rcv(), fix from Ying Cai.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
  net: macb: Fix race between HW and driver
  net: macb: Remove 'unlikely' optimization
  net: macb: Re-enable RX interrupt only when RX is done
  net: macb: Clear interrupt flags
  net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
  ip_tunnel: Set network header properly for IP_ECN_decapsulate()
  e1000e: Restrict MDIO Slow Mode workaround to relevant parts
  e1000e: Fix issue with link flap on 82579
  e1000e: Expand workaround for 10Mb HD throughput bug
  e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
  net/mlx4_core: Don't issue PCIe speed/width checks for VFs
  net/mlx4_core: Load the Eth driver first
  net/mlx4_core: Fix slave id computation for single port VF
  net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
  net: cdc_ncm: fix buffer overflow
  Altera TSE: ALTERA_TSE should depend on HAS_DMA
  vsock: Make transport the proto owner
  net: sched: lock imbalance in hhf qdisc
  net: mvmdio: Check for a valid interrupt instead of an error
  net phy: Check for aneg completion before setting state to PHY_RUNNING
  ...
2014-05-05 15:59:46 -07:00
Linus Torvalds
5575eeb7b9 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
 "First, there is a critical fix for the new primary-affinity function
  that went into -rc1.

  The second batch of patches from Zheng fix a range of problems with
  directory fragmentation, readdir, and a few odds and ends for cephfs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: reserve caps for file layout/lock MDS requests
  ceph: avoid releasing caps that are being used
  ceph: clear directory's completeness when creating file
  libceph: fix non-default values check in apply_primary_affinity()
  ceph: use fpos_cmp() to compare dentry positions
  ceph: check directory's completeness before emitting directory entry
2014-05-05 15:17:02 -07:00
Ying Cai
e96f2e7c43 ip_tunnel: Set network header properly for IP_ECN_decapsulate()
In ip_tunnel_rcv(), set skb->network_header to inner IP header
before IP_ECN_decapsulate().

Without the fix, IP_ECN_decapsulate() takes outer IP header as
inner IP header, possibly causing error messages or packet drops.

Note that this skb_reset_network_header() call was in this spot when
the original feature for checking consistency of ECN bits through
tunnels was added in eccc1bb8d4 ("tunnel: drop packet if ECN present
with not-ECT"). It was only removed from this spot in 3d7b46cd20
("ip_tunnel: push generic protocol handling to ip_tunnel module.").

Fixes: 3d7b46cd20 ("ip_tunnel: push generic protocol handling to ip_tunnel module.")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Ying Cai <ycai@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05 16:32:17 -04:00
Andy King
2c4a336e0a vsock: Make transport the proto owner
Right now the core vsock module is the owner of the proto family. This
means there's nothing preventing the transport module from unloading if
there are open sockets, which results in a panic. Fix that by allowing
the transport to be the owner, which will refcount it properly.

Includes version bump to 1.0.1.0-k

Passes checkpatch this time, I swear...

Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05 13:13:50 -04:00
David S. Miller
b8dff4e60c Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:

====================
pull request: wireless 2014-05-01

Please pull the following batch of fixes intended for the 3.15 stream!

For the Bluetooth bits, Gustavo says:

"Some fixes for 3.15. There is a revert for the intel driver, a new
device id, and two important SSP fixes from Johan."

On top of that...

Ben Hutchings gives us a fix for an unbalanced irq enable in an
rtl8192cu error path.

Colin Ian King provides an rtlwifi fix for an uninitialized variable.

Felix Fietkau brings a pair of ath9k fixes, one that corrects a
hardware initialization value and another that removes an (unnecessary)
flag that was being used in a way that led to a software tx queue
hang in ath9k.

Gertjan van Wingerde pushes a MAINTAINERS change to remove himself
from the rt2x00 maintainer team.

Hans de Goede fixes a brcmfmac firmware load hang.

Larry Finger changes rtlwifi to use the correct queue for V0 traffic
on rtl8192se.

Rajkumar Manoharan corrects a race in ath9k driver initialization.

Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing
once on USB devices led to permanently disabling beaconing for those
devices.

Tim Harvey provides fixes for a pair of ath9k issues that can lead
to soft lockups in that driver.

Please let me know if there are problems!
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05 13:06:01 -04:00
John Fastabend
f6a082fed1 net: sched: lock imbalance in hhf qdisc
hhf_change() takes the sch_tree_lock and releases it but misses the
error cases. Fix the missed case here.

To reproduce try a command like this,

# tc qdisc change dev p3p2 root hhf quantum 40960 non_hh_weight 300000

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-04 19:41:45 -04:00
John W. Linville
812e4dafa4 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem 2014-05-01 11:23:21 -04:00
Liu Yu
0cda345d1b tcp_cubic: fix the range of delayed_ack
commit b9f47a3aae (tcp_cubic: limit delayed_ack ratio to prevent
divide error) try to prevent divide error, but there is still a little
chance that delayed_ack can reach zero. In case the param cnt get
negative value, then ratio+cnt would overflow and may happen to be zero.
As a result, min(ratio, ACK_RATIO_LIMIT) will calculate to be zero.

In some old kernels, such as 2.6.32, there is a bug that would
pass negative param, which then ultimately leads to this divide error.

commit 5b35e1e6e9 (tcp: fix tcp_trim_head() to adjust segment count
with skb MSS) fixed the negative param issue. However,
it's safe that we fix the range of delayed_ack as well,
to make sure we do not hit a divide by zero.

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Liu Yu <allanyuliu@tencent.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30 16:12:22 -04:00
Eric Dumazet
fc9f350106 tcp: increment retransmit counters in tlp and fast open
Both TLP and Fast Open call __tcp_retransmit_skb() instead of
tcp_retransmit_skb() to avoid changing tp->retrans_out.

This has the side effect of missing SNMP counters increments as well
as tcp_info tcpi_total_retrans updates.

Fix this by moving the stats increments of into __tcp_retransmit_skb()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-30 16:12:22 -04:00
Ilya Dryomov
92b2e75158 libceph: fix non-default values check in apply_primary_affinity()
osd_primary_affinity array is indexed into incorrectly when checking
for non-default primary-affinity values.  This nullifies the impact of
the rest of the apply_primary_affinity() and results in misdirected
requests.

                if (osds[i] != CRUSH_ITEM_NONE &&
                    osdmap->osd_primary_affinity[i] !=
                                                ^^^
                                        CEPH_OSD_DEFAULT_PRIMARY_AFFINITY) {

For a pool with size 2, this always ends up checking osd0 and osd1
primary_affinity values, instead of the values that correspond to the
osds in question.  E.g., given a [2,3] up set and a [max,max,0,max]
primary affinity vector, requests are still sent to osd2, because both
osd0 and osd1 happen to have max primary_affinity values and therefore
we return from apply_primary_affinity() early on the premise that all
osds in the given set have max (default) values.  Fix it.

Fixes: http://tracker.ceph.com/issues/7954

Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
2014-04-28 12:54:10 -07:00
Julian Anastasov
e374c618b1 net: ipv6: more places need LOOPBACK_IFINDEX for flowi6_iif
To properly match iif in ip rules we have to provide
LOOPBACK_IFINDEX in flowi6_iif, not 0. Some ip6mr_fib_lookup
and fib6_rule_lookup callers need such fix.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-28 14:47:03 -04:00
Karl Heiss
8c2eab9097 net: sctp: Don't transition to PF state when transport has exhausted 'Path.Max.Retrans'.
Don't transition to the PF state on every strike after 'Path.Max.Retrans'.
Per draft-ietf-tsvwg-sctp-failover-03 Section 5.1.6:

   Additional (PMR - PFMR) consecutive timeouts on a PF destination
   confirm the path failure, upon which the destination transitions to the
   Inactive state.  As described in [RFC4960], the sender (i) SHOULD notify
   ULP about this state transition, and (ii) transmit heartbeats to the
   Inactive destination at a lower frequency as described in Section 8.3 of
   [RFC4960].

This also prevents sending SCTP_ADDR_UNREACHABLE to the user as the state
bounces between SCTP_INACTIVE and SCTP_PF for each subsequent strike.

Signed-off-by: Karl Heiss <kheiss@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27 23:41:14 -04:00
Xufeng Zhang
8535087131 sctp: reset flowi4_oif parameter on route lookup
commit 813b3b5db8 (ipv4: Use caller's on-stack flowi as-is
in output route lookups.) introduces another regression which
is very similar to the problem of commit e6b45241c (ipv4: reset
flowi parameters on route connect) wants to fix:
Before we call ip_route_output_key() in sctp_v4_get_dst() to
get a dst that matches a bind address as the source address,
we have already called this function previously and the flowi
parameters have been initialized including flowi4_oif, so when
we call this function again, the process in __ip_route_output_key()
will be different because of the setting of flowi4_oif, and we'll
get a networking device which corresponds to the inputted flowi4_oif
as the output device, this is wrong because we'll never hit this
place if the previously returned source address of dst match one
of the bound addresses.

To reproduce this problem, a vlan setting is enough:
  # ifconfig eth0 up
  # route del default
  # vconfig add eth0 2
  # vconfig add eth0 3
  # ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0
  # route add default gw 10.0.1.254 dev eth0.2
  # ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0
  # ip rule add from 10.0.0.14 table 4
  # ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3
  # sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I
You'll detect that all the flow are routed to eth0.2(10.0.1.254).

Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27 19:46:17 -04:00
Toshiaki Makita
30313a3d57 bridge: Handle IFLA_ADDRESS correctly when creating bridge device
When bridge device is created with IFLA_ADDRESS, we are not calling
br_stp_change_bridge_id(), which leads to incorrect local fdb
management and bridge id calculation, and prevents us from receiving
frames on the bridge device.

Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27 19:46:17 -04:00
Johan Hedberg
09da1f3463 Bluetooth: Fix redundant encryption request for reauthentication
When we're performing reauthentication (in order to elevate the
security level from an unauthenticated key to an authenticated one) we
do not need to issue any encryption command once authentication
completes. Since the trigger for the encryption HCI command is the
ENCRYPT_PEND flag this flag should not be set in this scenario.
Instead, the REAUTH_PEND flag takes care of all necessary steps for
reauthentication.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2014-04-25 09:47:15 +03:00
Johan Hedberg
9eb1fbfa0a Bluetooth: Fix triggering BR/EDR L2CAP Connect too early
Commit 1c2e004183 introduced an event handler for the encryption key
refresh complete event with the intent of fixing some LE/SMP cases.
However, this event is shared with BR/EDR and there we actually want to
act only on the auth_complete event (which comes after the key refresh).

If we do not do this we may trigger an L2CAP Connect Request too early
and cause the remote side to return a security block error.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2014-04-25 09:47:15 +03:00
Kumar Sundararajan
1c26585458 ipv6: fib: fix fib dump restart
When the ipv6 fib changes during a table dump, the walk is
restarted and the number of nodes dumped are skipped. But the existing
code doesn't advance to the next node after a node is skipped. This can
cause the dump to loop or produce lots of duplicates when the fib
is modified during the dump.

This change advances the walk to the next node if the current node is
skipped after a restart.

Signed-off-by: Kumar Sundararajan <kumar@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 17:19:25 -04:00
David Gibson
c53864fd60 rtnetlink: Only supply IFLA_VF_PORTS information when RTEXT_FILTER_VF is set
Since 115c9b8192 (rtnetlink: Fix problem with
buffer allocation), RTM_NEWLINK messages only contain the IFLA_VFINFO_LIST
attribute if they were solicited by a GETLINK message containing an
IFLA_EXT_MASK attribute with the RTEXT_FILTER_VF flag.

That was done because some user programs broke when they received more data
than expected - because IFLA_VFINFO_LIST contains information for each VF
it can become large if there are many VFs.

However, the IFLA_VF_PORTS attribute, supplied for devices which implement
ndo_get_vf_port (currently the 'enic' driver only), has the same problem.
It supplies per-VF information and can therefore become large, but it is
not currently conditional on the IFLA_EXT_MASK value.

Worse, it interacts badly with the existing EXT_MASK handling.  When
IFLA_EXT_MASK is not supplied, the buffer for netlink replies is fixed at
NLMSG_GOODSIZE.  If the information for IFLA_VF_PORTS exceeds this, then
rtnl_fill_ifinfo() returns -EMSGSIZE on the first message in a packet.
netlink_dump() will misinterpret this as having finished the listing and
omit data for this interface and all subsequent ones.  That can cause
getifaddrs(3) to enter an infinite loop.

This patch addresses the problem by only supplying IFLA_VF_PORTS when
IFLA_EXT_MASK is supplied with the RTEXT_FILTER_VF flag set.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 13:52:54 -04:00
David Gibson
973462bbde rtnetlink: Warn when interface's information won't fit in our packet
Without IFLA_EXT_MASK specified, the information reported for a single
interface in response to RTM_GETLINK is expected to fit within a netlink
packet of NLMSG_GOODSIZE.

If it doesn't, however, things will go badly wrong,  When listing all
interfaces, netlink_dump() will incorrectly treat -EMSGSIZE on the first
message in a packet as the end of the listing and omit information for
that interface and all subsequent ones.  This can cause getifaddrs(3) to
enter an infinite loop.

This patch won't fix the problem, but it will WARN_ON() making it easier to
track down what's going wrong.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 13:52:54 -04:00
David S. Miller
a64d90fd96 netfilter: Fix warning in nfnetlink_receive().
net/netfilter/nfnetlink.c: In function ‘nfnetlink_rcv’:
net/netfilter/nfnetlink.c:371:14: warning: unused variable ‘net’ [-Wunused-variable]

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 13:51:29 -04:00
Eric W. Biederman
90f62cf30a net: Use netlink_ns_capable to verify the permisions of netlink messages
It is possible by passing a netlink socket to a more privileged
executable and then to fool that executable into writing to the socket
data that happens to be valid netlink message to do something that
privileged executable did not intend to do.

To keep this from happening replace bare capable and ns_capable calls
with netlink_capable, netlink_net_calls and netlink_ns_capable calls.
Which act the same as the previous calls except they verify that the
opener of the socket had the desired permissions as well.

Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 13:44:54 -04:00
Eric W. Biederman
aa4cf9452f net: Add variants of capable for use on netlink messages
netlink_net_capable - The common case use, for operations that are safe on a network namespace
netlink_capable - For operations that are only known to be safe for the global root
netlink_ns_capable - The general case of capable used to handle special cases

__netlink_ns_capable - Same as netlink_ns_capable except taking a netlink_skb_parms instead of
		       the skbuff of a netlink message.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 13:44:54 -04:00
Eric W. Biederman
a3b299da86 net: Add variants of capable for use on on sockets
sk_net_capable - The common case, operations that are safe in a network namespace.
sk_capable - Operations that are not known to be safe in a network namespace
sk_ns_capable - The general case for special cases.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 13:44:53 -04:00
Eric W. Biederman
a53b72c83a net: Move the permission check in sock_diag_put_filterinfo to packet_diag_dump
The permission check in sock_diag_put_filterinfo is wrong, and it is so removed
from it's sources it is not clear why it is wrong.  Move the computation
into packet_diag_dump and pass a bool of the result into sock_diag_filterinfo.

This does not yet correct the capability check but instead simply moves it to make
it clear what is going on.

Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 13:44:53 -04:00
Eric W. Biederman
5187cd055b netlink: Rename netlink_capable netlink_allowed
netlink_capable is a static internal function in af_netlink.c and we
have better uses for the name netlink_capable.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-24 13:44:53 -04:00
Alexei Starovoitov
83d5b7ef99 net: filter: initialize A and X registers
exisiting BPF verifier allows uninitialized access to registers,
'ret A' is considered to be a valid filter.
So initialize A and X to zero to prevent leaking kernel memory
In the future BPF verifier will be rejecting such filters

Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-23 15:34:41 -04:00
Andrew Lutomirski
78541c1dc6 net: Fix ns_capable check in sock_diag_put_filterinfo
The caller needs capabilities on the namespace being queried, not on
their own namespace.  This is a security bug, although it likely has
only a minor impact.

Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-22 12:49:39 -04:00
Vlad Yasevich
b14878ccb7 net: sctp: cache auth_enable per endpoint
Currently, it is possible to create an SCTP socket, then switch
auth_enable via sysctl setting to 1 and crash the system on connect:

Oops[#1]:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.14.1-mipsgit-20140415 #1
task: ffffffff8056ce80 ti: ffffffff8055c000 task.ti: ffffffff8055c000
[...]
Call Trace:
[<ffffffff8043c4e8>] sctp_auth_asoc_set_default_hmac+0x68/0x80
[<ffffffff8042b300>] sctp_process_init+0x5e0/0x8a4
[<ffffffff8042188c>] sctp_sf_do_5_1B_init+0x234/0x34c
[<ffffffff804228c8>] sctp_do_sm+0xb4/0x1e8
[<ffffffff80425a08>] sctp_endpoint_bh_rcv+0x1c4/0x214
[<ffffffff8043af68>] sctp_rcv+0x588/0x630
[<ffffffff8043e8e8>] sctp6_rcv+0x10/0x24
[<ffffffff803acb50>] ip6_input+0x2c0/0x440
[<ffffffff8030fc00>] __netif_receive_skb_core+0x4a8/0x564
[<ffffffff80310650>] process_backlog+0xb4/0x18c
[<ffffffff80313cbc>] net_rx_action+0x12c/0x210
[<ffffffff80034254>] __do_softirq+0x17c/0x2ac
[<ffffffff800345e0>] irq_exit+0x54/0xb0
[<ffffffff800075a4>] ret_from_irq+0x0/0x4
[<ffffffff800090ec>] rm7k_wait_irqoff+0x24/0x48
[<ffffffff8005e388>] cpu_startup_entry+0xc0/0x148
[<ffffffff805a88b0>] start_kernel+0x37c/0x398
Code: dd0900b8  000330f8  0126302d <dcc60000> 50c0fff1  0047182a  a48306a0
03e00008  00000000
---[ end trace b530b0551467f2fd ]---
Kernel panic - not syncing: Fatal exception in interrupt

What happens while auth_enable=0 in that case is, that
ep->auth_hmacs is initialized to NULL in sctp_auth_init_hmacs()
when endpoint is being created.

After that point, if an admin switches over to auth_enable=1,
the machine can crash due to NULL pointer dereference during
reception of an INIT chunk. When we enter sctp_process_init()
via sctp_sf_do_5_1B_init() in order to respond to an INIT chunk,
the INIT verification succeeds and while we walk and process
all INIT params via sctp_process_param() we find that
net->sctp.auth_enable is set, therefore do not fall through,
but invoke sctp_auth_asoc_set_default_hmac() instead, and thus,
dereference what we have set to NULL during endpoint
initialization phase.

The fix is to make auth_enable immutable by caching its value
during endpoint initialization, so that its original value is
being carried along until destruction. The bug seems to originate
from the very first days.

Fix in joint work with Daniel Borkmann.

Reported-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-18 18:32:00 -04:00
David S. Miller
5a292f7bc6 Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:

====================
pull request: wireless 2014-04-17

Please pull this batch of fixes intended for the 3.15 stream...

For the mac80211 bits, Johannes says:

"We have a fix from Chun-Yeow to not look at management frame bitrates
that are typically really low, two fixes from Felix for AP_VLAN
interfaces, a fix from Ido to disable SMPS settings when a monitor
interface is enabled, a radar detection fix from Michał and a fix from
myself for a very old remain-on-channel bug."

For the iwlwifi bits, Emmanuel says:

"I have new device IDs and a new firmware API. These are the trivial
ones. The less trivial ones are Johannes's fix that delays the
enablement of an interrupt coalescing hardware until after association
- this fixes a few connection problems seen in the field. Eyal has a
bunch of rate control fixes. I decided to add these for 3.15 because
they fix some disconnection and packet loss scenarios which were
reported by the field. I also have a fix for a memory leak that
happens only with a very new NIC."

Along with those...

Amitkumar Karwar fixes a couple of problems relating to driver/firmware
interactions in mwifiex.

Christian Engelmayer avoids a couple of potential memory leaks in
the new rsi driver.

Eliad Peller provides a wl18xx mailbox alignment fix for problems
when using new firmware.

Frederic Danis adds a couple of missing debugging strings to the
cw1200 driver.

Geert Uytterhoeven adds a variable initialization inside of the
rsi driver.

Luciano Coelho patches the wlcore code to ignore dummy packet events
in PLT mode in order to work around a firmware bug.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-18 18:29:44 -04:00
dingtianhong
dc8eaaa006 vlan: Fix lockdep warning when vlan dev handle notification
When I open the LOCKDEP config and run these steps:

modprobe 8021q
vconfig add eth2 20
vconfig add eth2.20 30
ifconfig eth2 xx.xx.xx.xx

then the Call Trace happened:

[32524.386288] =============================================
[32524.386293] [ INFO: possible recursive locking detected ]
[32524.386298] 3.14.0-rc2-0.7-default+ #35 Tainted: G           O
[32524.386302] ---------------------------------------------
[32524.386306] ifconfig/3103 is trying to acquire lock:
[32524.386310]  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff814275f4>] dev_mc_sync+0x64/0xb0
[32524.386326]
[32524.386326] but task is already holding lock:
[32524.386330]  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff8141af83>] dev_set_rx_mode+0x23/0x40
[32524.386341]
[32524.386341] other info that might help us debug this:
[32524.386345]  Possible unsafe locking scenario:
[32524.386345]
[32524.386350]        CPU0
[32524.386352]        ----
[32524.386354]   lock(&vlan_netdev_addr_lock_key/1);
[32524.386359]   lock(&vlan_netdev_addr_lock_key/1);
[32524.386364]
[32524.386364]  *** DEADLOCK ***
[32524.386364]
[32524.386368]  May be due to missing lock nesting notation
[32524.386368]
[32524.386373] 2 locks held by ifconfig/3103:
[32524.386376]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81431d42>] rtnl_lock+0x12/0x20
[32524.386387]  #1:  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff8141af83>] dev_set_rx_mode+0x23/0x40
[32524.386398]
[32524.386398] stack backtrace:
[32524.386403] CPU: 1 PID: 3103 Comm: ifconfig Tainted: G           O 3.14.0-rc2-0.7-default+ #35
[32524.386409] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[32524.386414]  ffffffff81ffae40 ffff8800d9625ae8 ffffffff814f68a2 ffff8800d9625bc8
[32524.386421]  ffffffff810a35fb ffff8800d8a8d9d0 00000000d9625b28 ffff8800d8a8e5d0
[32524.386428]  000003cc00000000 0000000000000002 ffff8800d8a8e5f8 0000000000000000
[32524.386435] Call Trace:
[32524.386441]  [<ffffffff814f68a2>] dump_stack+0x6a/0x78
[32524.386448]  [<ffffffff810a35fb>] __lock_acquire+0x7ab/0x1940
[32524.386454]  [<ffffffff810a323a>] ? __lock_acquire+0x3ea/0x1940
[32524.386459]  [<ffffffff810a4874>] lock_acquire+0xe4/0x110
[32524.386464]  [<ffffffff814275f4>] ? dev_mc_sync+0x64/0xb0
[32524.386471]  [<ffffffff814fc07a>] _raw_spin_lock_nested+0x2a/0x40
[32524.386476]  [<ffffffff814275f4>] ? dev_mc_sync+0x64/0xb0
[32524.386481]  [<ffffffff814275f4>] dev_mc_sync+0x64/0xb0
[32524.386489]  [<ffffffffa0500cab>] vlan_dev_set_rx_mode+0x2b/0x50 [8021q]
[32524.386495]  [<ffffffff8141addf>] __dev_set_rx_mode+0x5f/0xb0
[32524.386500]  [<ffffffff8141af8b>] dev_set_rx_mode+0x2b/0x40
[32524.386506]  [<ffffffff8141b3cf>] __dev_open+0xef/0x150
[32524.386511]  [<ffffffff8141b177>] __dev_change_flags+0xa7/0x190
[32524.386516]  [<ffffffff8141b292>] dev_change_flags+0x32/0x80
[32524.386524]  [<ffffffff8149ca56>] devinet_ioctl+0x7d6/0x830
[32524.386532]  [<ffffffff81437b0b>] ? dev_ioctl+0x34b/0x660
[32524.386540]  [<ffffffff814a05b0>] inet_ioctl+0x80/0xa0
[32524.386550]  [<ffffffff8140199d>] sock_do_ioctl+0x2d/0x60
[32524.386558]  [<ffffffff81401a52>] sock_ioctl+0x82/0x2a0
[32524.386568]  [<ffffffff811a7123>] do_vfs_ioctl+0x93/0x590
[32524.386578]  [<ffffffff811b2705>] ? rcu_read_lock_held+0x45/0x50
[32524.386586]  [<ffffffff811b39e5>] ? __fget_light+0x105/0x110
[32524.386594]  [<ffffffff811a76b1>] SyS_ioctl+0x91/0xb0
[32524.386604]  [<ffffffff815057e2>] system_call_fastpath+0x16/0x1b

========================================================================

The reason is that all of the addr_lock_key for vlan dev have the same class,
so if we change the status for vlan dev, the vlan dev and its real dev will
hold the same class of addr_lock_key together, so the warning happened.

we should distinguish the lock depth for vlan dev and its real dev.

v1->v2: Convert the vlan_netdev_addr_lock_key to an array of eight elements, which
	could support to add 8 vlan id on a same vlan dev, I think it is enough for current
	scene, because a netdev's name is limited to IFNAMSIZ which could not hold 8 vlan id,
	and the vlan dev would not meet the same class key with its real dev.

	The new function vlan_dev_get_lockdep_subkey() will return the subkey and make the vlan
	dev could get a suitable class key.

v2->v3: According David's suggestion, I use the subclass to distinguish the lock key for vlan dev
	and its real dev, but it make no sense, because the difference for subclass in the
	lock_class_key doesn't mean that the difference class for lock_key, so I use lock_depth
	to distinguish the different depth for every vlan dev, the same depth of the vlan dev
	could have the same lock_class_key, I import the MAX_LOCK_DEPTH from the include/linux/sched.h,
	I think it is enough here, the lockdep should never exceed that value.

v3->v4: Add a huge array of locking keys will waste static kernel memory and is not a appropriate method,
	we could use _nested() variants to fix the problem, calculate the depth for every vlan dev,
	and use the depth as the subclass for addr_lock_key.

Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-18 17:48:30 -04:00
John W. Linville
4a0c3d9fd1 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem 2014-04-17 10:34:22 -04:00
Nicolas Dichtel
74462f0d4a ip6_tunnel: use the right netns in ioctl handler
Because the netdevice may be in another netns than the i/o netns, we should
use the i/o netns instead of dev_net(dev).

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-16 15:16:02 -04:00
Nicolas Dichtel
9aad77c3b5 sit: use the right netns in ioctl handler
Because the netdevice may be in another netns than the i/o netns, we should
use the i/o netns instead of dev_net(dev).

Note that netdev_priv(dev) cannot bu NULL, hence we can remove these useless
checks.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-16 15:16:02 -04:00
Nicolas Dichtel
8c923ce219 ip_tunnel: use the right netns in ioctl handler
Because the netdevice may be in another netns than the i/o netns, we should
use the i/o netns instead of dev_net(dev).

The variable 'tunnel' was used only to get 'itn', hence to simplify code I
remove it and use 't' instead.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-16 15:16:02 -04:00
Jan Glauber
b7c0ddf5f2 net: use SYSCALL_DEFINEx for sys_recv
Make sys_recv a first class citizen by using the SYSCALL_DEFINEx
macro. Besides being cleaner this will also generate meta data
for the system call so tracing tools like ftrace or LTTng can
resolve this system call.

Signed-off-by: Jan Glauber <jan.glauber@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-16 15:15:05 -04:00
Cong Wang
0d5edc6873 ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
In my special case, when a packet is redirected from veth0 to lo,
its skb->dev->ifindex would be LOOPBACK_IFINDEX. Meanwhile we
pass the hard-coded LOOPBACK_IFINDEX to fib_validate_source()
in ip_route_input_slow(). This would cause the following check
in fib_validate_source() fail:

            (dev->ifindex != oif || !IN_DEV_TX_REDIRECTS(idev))

when rp_filter is disabeld on loopback. As suggested by Julian,
the caller should pass 0 here so that we will not end up by
calling __fib_validate_source().

Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-16 15:05:12 -04:00
Cong Wang
6a662719c9 ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
As suggested by Julian:

	Simply, flowi4_iif must not contain 0, it does not
	look logical to ignore all ip rules with specified iif.

because in fib_rule_match() we do:

        if (rule->iifindex && (rule->iifindex != fl->flowi_iif))
                goto out;

flowi4_iif should be LOOPBACK_IFINDEX by default.

We need to move LOOPBACK_IFINDEX to include/net/flow.h:

1) It is mostly used by flowi_iif

2) Fix the following compile error if we use it in flow.h
by the patches latter:

In file included from include/linux/netfilter.h:277:0,
                 from include/net/netns/netfilter.h:5,
                 from include/net/net_namespace.h:21,
                 from include/linux/netdevice.h:43,
                 from include/linux/icmpv6.h:12,
                 from include/linux/ipv6.h:61,
                 from include/net/ipv6.h:16,
                 from include/linux/sunrpc/clnt.h:27,
                 from include/linux/nfs_fs.h:30,
                 from init/do_mounts.c:32:
include/net/flow.h: In function ‘flowi4_init_output’:
include/net/flow.h:84:32: error: ‘LOOPBACK_IFINDEX’ undeclared (first use in this function)

Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-16 15:05:11 -04:00
Nicolas Dichtel
54d63f787b ip6_gre: don't allow to remove the fb_tunnel_dev
It's possible to remove the FB tunnel with the command 'ip link del ip6gre0' but
this is unsafe, the module always supposes that this device exists. For example,
ip6gre_tunnel_lookup() may use it unconditionally.

Let's add a rtnl handler for dellink, which will never remove the FB tunnel (we
let ip6gre_destroy_tunnels() do the job).

Introduced by commit c12b395a46 ("gre: Support GRE over IPv6").

CC: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-15 14:56:19 -04:00
Eric Dumazet
aad88724c9 ipv4: add a sock pointer to dst->output() path.
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.

The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.

Fixes: 8f646c922d ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-15 13:47:15 -04:00
Eric Dumazet
b0270e9101 ipv4: add a sock pointer to ip_queue_xmit()
ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d5956 ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.

One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.

Fixes: 31c70d5956 ("l2tp: keep original skb ownership")
Reported-by: Zhan Jianyu <nasa4836@gmail.com>
Tested-by: Zhan Jianyu <nasa4836@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-15 12:58:34 -04:00
David S. Miller
00cbc3dcd1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains three Netfilter fixes for your net tree,
they are:

* Fix missing generation sequence initialization which results in a splat
  if lockdep is enabled, it was introduced in the recent works to improve
  nf_conntrack scalability, from Andrey Vagin.

* Don't flush the GRE keymap list in nf_conntrack when the pptp helper is
  disabled otherwise this crashes due to a double release, from Andrey
  Vagin.

* Fix nf_tables cmp fast in big endian, from Patrick McHardy.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-14 19:00:10 -04:00
Vlad Yasevich
1e785f48d2 net: Start with correct mac_len in skb_network_protocol
Sometimes, when the packet arrives at skb_mac_gso_segment()
its skb->mac_len already accounts for some of the mac lenght
headers in the packet.  This seems to happen when forwarding
through and OpenSSL tunnel.

When we start looking for any vlan headers in skb_network_protocol()
we seem to ignore any of the already known mac headers and start
with an ETH_HLEN.  This results in an incorrect offset, dropped
TSO frames and general slowness of the connection.

We can start counting from the known skb->mac_len
and return at least that much if all mac level headers
are known and accounted for.

Fixes: 53d6471cef (net: Account for all vlan headers in skb_mac_gso_segment)
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Daniel Borkman <dborkman@redhat.com>
Tested-by: Martin Filip <nexus+kernel@smoula.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-14 18:58:58 -04:00
Daniel Borkmann
362d52040c Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
This reverts commit ef2820a735 ("net: sctp: Fix a_rwnd/rwnd management
to reflect real state of the receiver's buffer") as it introduced a
serious performance regression on SCTP over IPv4 and IPv6, though a not
as dramatic on the latter. Measurements are on 10Gbit/s with ixgbe NICs.

Current state:

[root@Lab200slot2 ~]# iperf3 --sctp -4 -c 192.168.241.3 -V -l 1452 -t 60
iperf version 3.0.1 (10 January 2014)
Linux Lab200slot2 3.14.0 #1 SMP Thu Apr 3 23:18:29 EDT 2014 x86_64
Time: Fri, 11 Apr 2014 17:56:21 GMT
Connecting to host 192.168.241.3, port 5201
      Cookie: Lab200slot2.1397238981.812898.548918
[  4] local 192.168.241.2 port 38616 connected to 192.168.241.3 port 5201
Starting Test: protocol: SCTP, 1 streams, 1452 byte blocks, omitting 0 seconds, 60 second test
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.09   sec  20.8 MBytes   161 Mbits/sec
[  4]   1.09-2.13   sec  10.8 MBytes  86.8 Mbits/sec
[  4]   2.13-3.15   sec  3.57 MBytes  29.5 Mbits/sec
[  4]   3.15-4.16   sec  4.33 MBytes  35.7 Mbits/sec
[  4]   4.16-6.21   sec  10.4 MBytes  42.7 Mbits/sec
[  4]   6.21-6.21   sec  0.00 Bytes    0.00 bits/sec
[  4]   6.21-7.35   sec  34.6 MBytes   253 Mbits/sec
[  4]   7.35-11.45  sec  22.0 MBytes  45.0 Mbits/sec
[  4]  11.45-11.45  sec  0.00 Bytes    0.00 bits/sec
[  4]  11.45-11.45  sec  0.00 Bytes    0.00 bits/sec
[  4]  11.45-11.45  sec  0.00 Bytes    0.00 bits/sec
[  4]  11.45-12.51  sec  16.0 MBytes   126 Mbits/sec
[  4]  12.51-13.59  sec  20.3 MBytes   158 Mbits/sec
[  4]  13.59-14.65  sec  13.4 MBytes   107 Mbits/sec
[  4]  14.65-16.79  sec  33.3 MBytes   130 Mbits/sec
[  4]  16.79-16.79  sec  0.00 Bytes    0.00 bits/sec
[  4]  16.79-17.82  sec  5.94 MBytes  48.7 Mbits/sec
(etc)

[root@Lab200slot2 ~]#  iperf3 --sctp -6 -c 2001:db8:0:f101::1 -V -l 1400 -t 60
iperf version 3.0.1 (10 January 2014)
Linux Lab200slot2 3.14.0 #1 SMP Thu Apr 3 23:18:29 EDT 2014 x86_64
Time: Fri, 11 Apr 2014 19:08:41 GMT
Connecting to host 2001:db8:0:f101::1, port 5201
      Cookie: Lab200slot2.1397243321.714295.2b3f7c
[  4] local 2001:db8:0:f101::2 port 55804 connected to 2001:db8:0:f101::1 port 5201
Starting Test: protocol: SCTP, 1 streams, 1400 byte blocks, omitting 0 seconds, 60 second test
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.00   sec   169 MBytes  1.42 Gbits/sec
[  4]   1.00-2.00   sec   201 MBytes  1.69 Gbits/sec
[  4]   2.00-3.00   sec   188 MBytes  1.58 Gbits/sec
[  4]   3.00-4.00   sec   174 MBytes  1.46 Gbits/sec
[  4]   4.00-5.00   sec   165 MBytes  1.39 Gbits/sec
[  4]   5.00-6.00   sec   199 MBytes  1.67 Gbits/sec
[  4]   6.00-7.00   sec   163 MBytes  1.36 Gbits/sec
[  4]   7.00-8.00   sec   174 MBytes  1.46 Gbits/sec
[  4]   8.00-9.00   sec   193 MBytes  1.62 Gbits/sec
[  4]   9.00-10.00  sec   196 MBytes  1.65 Gbits/sec
[  4]  10.00-11.00  sec   157 MBytes  1.31 Gbits/sec
[  4]  11.00-12.00  sec   175 MBytes  1.47 Gbits/sec
[  4]  12.00-13.00  sec   192 MBytes  1.61 Gbits/sec
[  4]  13.00-14.00  sec   199 MBytes  1.67 Gbits/sec
(etc)

After patch:

[root@Lab200slot2 ~]#  iperf3 --sctp -4 -c 192.168.240.3 -V -l 1452 -t 60
iperf version 3.0.1 (10 January 2014)
Linux Lab200slot2 3.14.0+ #1 SMP Mon Apr 14 12:06:40 EDT 2014 x86_64
Time: Mon, 14 Apr 2014 16:40:48 GMT
Connecting to host 192.168.240.3, port 5201
      Cookie: Lab200slot2.1397493648.413274.65e131
[  4] local 192.168.240.2 port 50548 connected to 192.168.240.3 port 5201
Starting Test: protocol: SCTP, 1 streams, 1452 byte blocks, omitting 0 seconds, 60 second test
[ ID] Interval           Transfer     Bandwidth
[  4]   0.00-1.00   sec   240 MBytes  2.02 Gbits/sec
[  4]   1.00-2.00   sec   239 MBytes  2.01 Gbits/sec
[  4]   2.00-3.00   sec   240 MBytes  2.01 Gbits/sec
[  4]   3.00-4.00   sec   239 MBytes  2.00 Gbits/sec
[  4]   4.00-5.00   sec   245 MBytes  2.05 Gbits/sec
[  4]   5.00-6.00   sec   240 MBytes  2.01 Gbits/sec
[  4]   6.00-7.00   sec   240 MBytes  2.02 Gbits/sec
[  4]   7.00-8.00   sec   239 MBytes  2.01 Gbits/sec

With the reverted patch applied, the SCTP/IPv4 performance is back
to normal on latest upstream for IPv4 and IPv6 and has same throughput
as 3.4.2 test kernel, steady and interval reports are smooth again.

Fixes: ef2820a735 ("net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer")
Reported-by: Peter Butler <pbutler@sonusnet.com>
Reported-by: Dongsheng Song <dongsheng.song@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Peter Butler <pbutler@sonusnet.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nsn.com>
Cc: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-14 16:26:48 -04:00
Daniel Borkmann
8c482cdc35 net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
While reviewing seccomp code, we found that BPF_S_ANC_SECCOMP_LD_W has
been wrongly decoded by commit a8fc927780 ("sk-filter: Add ability to
get socket filter program (v2)") into the opcode BPF_LD|BPF_B|BPF_ABS
although it should have been decoded as BPF_LD|BPF_W|BPF_ABS.

In practice, this should not have much side-effect though, as such
conversion is/was being done through prctl(2) PR_SET_SECCOMP. Reverse
operation PR_GET_SECCOMP will only return the current seccomp mode, but
not the filter itself. Since the transition to the new BPF infrastructure,
it's also not used anymore, so we can simply remove this as it's
unreachable.

Fixes: a8fc927780 ("sk-filter: Add ability to get socket filter program (v2)")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-14 16:26:47 -04:00
John W. Linville
08e22e193a Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 2014-04-14 13:47:01 -04:00
Eric Dumazet
30f78d8ebf ipv6: Limit mtu to 65575 bytes
Francois reported that setting big mtu on loopback device could prevent
tcp sessions making progress.

We do not support (yet ?) IPv6 Jumbograms and cook corrupted packets.

We must limit the IPv6 MTU to (65535 + 40) bytes in theory.

Tested:

ifconfig lo mtu 70000
netperf -H ::1

Before patch : Throughput :   0.05 Mbits

After patch : Throughput : 35484 Mbits

Reported-by: Francois WELLENREITER <f.wellenreiter@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-14 12:39:59 -04:00
Patrick McHardy
b855d416dc netfilter: nf_tables: fix nft_cmp_fast failure on big endian for size < 4
nft_cmp_fast is used for equality comparisions of size <= 4. For
comparisions of size < 4 byte a mask is calculated that is applied to
both the data from userspace (during initialization) and the register
value (during runtime). Both values are stored using (in effect) memcpy
to a memory area that is then interpreted as u32 by nft_cmp_fast.

This works fine on little endian since smaller types have the same base
address, however on big endian this is not true and the smaller types
are interpreted as a big number with trailing zero bytes.

The mask therefore must not include the lower bytes, but the higher bytes
on big endian. Add a helper function that does a cpu_to_le32 to switch
the bytes on big endian. Since we're dealing with a mask of just consequitive
bits, this works out fine.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2014-04-14 10:38:02 +02:00
Andrey Vagin
ee214d54bf netfilter: nf_conntrack: initialize net.ct.generation
[  251.920788] INFO: trying to register non-static key.
[  251.921386] the code is fine but needs lockdep annotation.
[  251.921386] turning off the locking correctness validator.
[  251.921386] CPU: 2 PID: 15715 Comm: socket_listen Not tainted 3.14.0+ #294
[  251.921386] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[  251.921386]  0000000000000000 000000009d18c210 ffff880075f039b8 ffffffff816b7ecd
[  251.921386]  ffffffff822c3b10 ffff880075f039c8 ffffffff816b36f4 ffff880075f03aa0
[  251.921386]  ffffffff810c65ff ffffffff810c4a85 00000000fffffe01 ffffffffa0075172
[  251.921386] Call Trace:
[  251.921386]  [<ffffffff816b7ecd>] dump_stack+0x45/0x56
[  251.921386]  [<ffffffff816b36f4>] register_lock_class.part.24+0x38/0x3c
[  251.921386]  [<ffffffff810c65ff>] __lock_acquire+0x168f/0x1b40
[  251.921386]  [<ffffffff810c4a85>] ? trace_hardirqs_on_caller+0x105/0x1d0
[  251.921386]  [<ffffffffa0075172>] ? nf_nat_setup_info+0x252/0x3a0 [nf_nat]
[  251.921386]  [<ffffffff816c1215>] ? _raw_spin_unlock_bh+0x35/0x40
[  251.921386]  [<ffffffffa0075172>] ? nf_nat_setup_info+0x252/0x3a0 [nf_nat]
[  251.921386]  [<ffffffff810c7272>] lock_acquire+0xa2/0x120
[  251.921386]  [<ffffffffa008ab90>] ? ipv4_confirm+0x90/0xf0 [nf_conntrack_ipv4]
[  251.921386]  [<ffffffffa0055989>] __nf_conntrack_confirm+0x129/0x410 [nf_conntrack]
[  251.921386]  [<ffffffffa008ab90>] ? ipv4_confirm+0x90/0xf0 [nf_conntrack_ipv4]
[  251.921386]  [<ffffffffa008ab90>] ipv4_confirm+0x90/0xf0 [nf_conntrack_ipv4]
[  251.921386]  [<ffffffff815e7b00>] ? ip_fragment+0x9f0/0x9f0
[  251.921386]  [<ffffffff815d8c5a>] nf_iterate+0xaa/0xc0
[  251.921386]  [<ffffffff815e7b00>] ? ip_fragment+0x9f0/0x9f0
[  251.921386]  [<ffffffff815d8d14>] nf_hook_slow+0xa4/0x190
[  251.921386]  [<ffffffff815e7b00>] ? ip_fragment+0x9f0/0x9f0
[  251.921386]  [<ffffffff815e98f2>] ip_output+0x92/0x100
[  251.921386]  [<ffffffff815e8df9>] ip_local_out+0x29/0x90
[  251.921386]  [<ffffffff815e9240>] ip_queue_xmit+0x170/0x4c0
[  251.921386]  [<ffffffff815e90d5>] ? ip_queue_xmit+0x5/0x4c0
[  251.921386]  [<ffffffff81601208>] tcp_transmit_skb+0x498/0x960
[  251.921386]  [<ffffffff81602d82>] tcp_connect+0x812/0x960
[  251.921386]  [<ffffffff810e3dc5>] ? ktime_get_real+0x25/0x70
[  251.921386]  [<ffffffff8159ea2a>] ? secure_tcp_sequence_number+0x6a/0xc0
[  251.921386]  [<ffffffff81606f57>] tcp_v4_connect+0x317/0x470
[  251.921386]  [<ffffffff8161f645>] __inet_stream_connect+0xb5/0x330
[  251.921386]  [<ffffffff8158dfc3>] ? lock_sock_nested+0x33/0xa0
[  251.921386]  [<ffffffff810c4b5d>] ? trace_hardirqs_on+0xd/0x10
[  251.921386]  [<ffffffff81078885>] ? __local_bh_enable_ip+0x75/0xe0
[  251.921386]  [<ffffffff8161f8f8>] inet_stream_connect+0x38/0x50
[  251.921386]  [<ffffffff8158b157>] SYSC_connect+0xe7/0x120
[  251.921386]  [<ffffffff810e3789>] ? current_kernel_time+0x69/0xd0
[  251.921386]  [<ffffffff810c4a85>] ? trace_hardirqs_on_caller+0x105/0x1d0
[  251.921386]  [<ffffffff810c4b5d>] ? trace_hardirqs_on+0xd/0x10
[  251.921386]  [<ffffffff8158c36e>] SyS_connect+0xe/0x10
[  251.921386]  [<ffffffff816caf69>] system_call_fastpath+0x16/0x1b
[  312.014104] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=60003 jiffies, g=42359, c=42358, q=333)
[  312.015097] INFO: Stall ended before state dump start

Fixes: 93bb0ceb75 ("netfilter: conntrack: remove central spinlock nf_conntrack_lock")
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2014-04-14 10:35:28 +02:00
Mathias Krause
05ab8f2647 filter: prevent nla extensions to peek beyond the end of the message
The BPF_S_ANC_NLATTR and BPF_S_ANC_NLATTR_NEST extensions fail to check
for a minimal message length before testing the supplied offset to be
within the bounds of the message. This allows the subtraction of the nla
header to underflow and therefore -- as the data type is unsigned --
allowing far to big offset and length values for the search of the
netlink attribute.

The remainder calculation for the BPF_S_ANC_NLATTR_NEST extension is
also wrong. It has the minuend and subtrahend mixed up, therefore
calculates a huge length value, allowing to overrun the end of the
message while looking for the netlink attribute.

The following three BPF snippets will trigger the bugs when attached to
a UNIX datagram socket and parsing a message with length 1, 2 or 3.

 ,-[ PoC for missing size check in BPF_S_ANC_NLATTR ]--
 | ld	#0x87654321
 | ldx	#42
 | ld	#nla
 | ret	a
 `---

 ,-[ PoC for the same bug in BPF_S_ANC_NLATTR_NEST ]--
 | ld	#0x87654321
 | ldx	#42
 | ld	#nlan
 | ret	a
 `---

 ,-[ PoC for wrong remainder calculation in BPF_S_ANC_NLATTR_NEST ]--
 | ; (needs a fake netlink header at offset 0)
 | ld	#0
 | ldx	#42
 | ld	#nlan
 | ret	a
 `---

Fix the first issue by ensuring the message length fulfills the minimal
size constrains of a nla header. Fix the second bug by getting the math
for the remainder calculation right.

Fixes: 4738c1db15 ("[SKFILTER]: Add SKF_ADF_NLATTR instruction")
Fixes: d214c7537b ("filter: add SKF_AD_NLATTR_NEST to look for nested..")
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-13 23:31:55 -04:00
Julian Anastasov
91146153da ipv4: return valid RTA_IIF on ip route get
Extend commit 13378cad02
("ipv4: Change rt->rt_iif encoding.") from 3.6 to return valid
RTA_IIF on 'ip route get ... iif DEVICE' instead of rt_iif 0
which is displayed as 'iif *'.

inet_iif is not appropriate to use because skb_iif is not set.
Use the skb->dev->ifindex instead.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-13 23:23:41 -04:00