seq_ports.c::snd_seq_delete_all_ports() uses __list_add() to replace the
whole list entries. This results in BUG() with recent FC5 kernel due to
a sanity check in __list_add().
The patch fixes this misue of __list_add() by using standard macros
instead (although a bit more code is needed).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the model entry 'laptop-eapd' for Samsung X60 Chane with
AD1986A codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The dynamic minors code is mature, has been tested, and seems to work
fine.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
When snd-aoa is not built or built as modules, but CONFIG_SND is yes,
kernel build fails due to a bug I introduced when adding snd-aoa. This
patch fixes it.
From: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds two mixer controls. The V_REFOUT enable is a
documented register that couples the microphone input lines
to the V_REFOUT DC source. The High Pass Filter enable in the
AC97_AD_TEST2 (0x5c) is an undocumented register provided by
Miller Puckette via Analog Devices that enables the AD codec
to apply a high pass filter to the input.
Signed-off-by: Jaya Kumar <jayakumar.alsa@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Suppress 'irq handler mismatch' messages at auto-probing of irqs
in ALSA ISA drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
From: Sam Revitch <sam.revitch@gmail.com>Recently a Turtle Beach Audio Advantage Roadie device ended up in my
possession. It seems to work with the snd-usb-audio driver, but only
using the headphone jack in 2-channel mode. The device has a DIN
connector carrying six more channels that are otherwise silent.
C-Media has freely available documentation for the CM106 chip around
which this device is based, and enabling 8-channel output, or
6-channel output with the headphone jack following the front pair is a
matter of setting one of its registers.
Attached is a patch to try to enable 5.1 output mode at probe time.
It seems to work correctly with my device. There is quite list of
other configurables for this device that might deserve controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The following patch fixes two spots in the SN kernel
that check a fixed prom revision number to determine prom
feature support. These checks are only valid on shub1 systems.
They are invalid on shub2 systems which have a different prom
with different revision numbers.
Signed-off-by: Aaron Young <ayoung@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The code in "1007:" is in the .fixup section, which in the mmuless
case is discarded. Since this code is referenced from the .text
section, it causes an link error. Move this code into the .text
section instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In noMMU mode, various of functions which are defined in mm/proc-*.S
is not valid or needed to be avoided. i.g. switch_mm is not needed,
just returns and this makes the I & D caches are valid which shows
great improvement of performance including task switching and IPC.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hyok says Intel Xscale is not currently supported by uCLinux.
Rather than adding #error statements to the Xscale support files
and causing !MMU+Xscale configurations to fail to build, prevent
Xscale-based machines from being selected in !MMU mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a trivial patch to export flush_dcache_page in mm/nommu.c.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove fault-armv.o, mmap.o and mm-armv.o from uclinux builds - these
are concerned with MMU-ful operations, and as such are redundant for
uclinux.
Since this also removes iotable_init() and iotable_init() is used
extensively in the platform support files, just make it a no-op.
Based upon a couple of patches by Hyok.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
TABLE_SIZE is never used in arch/arm/mm/init.c. create_memmap_holes(),
memtable_init, and setup_io_desc() no longer exist in the kernel.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
nommu doesn't require a complex flush_dcache_page implementation
like the MMU-ful CPUs do, so provide a simplified version in nommu.c
and omit flush.c from the build as appropriate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include Kconfig-nommu when MMU is not selected.
(This is part of a patch from Hyok.)
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
nommu doesn't have any form of remapping support, so ioremap, etc
become stubs which just return the casted address, doing nothing
else.
Move ioport_map(), ioport_unmap(), pci_iomap(), pci_iounmap()
into a separate file which is always built.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since uclinux doesn't make use of the TLB, including the TLB
maintainence and CPU-optimised copypage functions does not
make sense. Remove them.
(This is part of one of Hyok's patches.)
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MMUless systems have only one address space for all threads, so
both the usual access_ok() checks, and the exception handling do
not make much sense.
Hence, discard the fixup and exception tables at link time, use
memcpy/memset for the user copy/clearing functions, and define
the permission check macros to be constants.
Some of this patch was derived from the equivalent patch by
Hyok S. Choi.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Majorily based on Hyok Choi's patches, this fixes up the asm-arm
header files for mmuless systems. Over and above Hyok's patches:
- nommu.h merged into mmu.h (it's only a structure)
- nommu_context.h is essentially the same as mmu_context.h, but
without the MM switching code.
so there's no point having separate files. Also, in memory.h,
there's no point #ifndef'ing PHYS_OFFSET and END_MEM - both
CONFIG_DRAM_BASE and CONFIG_DRAM_SIZE will always be set by the
configuration scripts.
Other files have minor formatting changes, but are essentially
the same. Hyok's original patches were signed off thusly:
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since there can be no fixed location for the TLS value with nommu
systems, we must provide TLS register emulation in order to support
TLS binaries on CPUs without the thread register.
Part of a patch from Hyok S. Choi, and cleaned up by rmk.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Montecito is coming with dual core and threading, so this
four socket box can now have sixteen logical cpus.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pass the OS logical cpu number to the PROM. This allows PROM
to log the OS logical cpu number in error records viewed thru POD.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Chandra Seetharaman missed one place in commit:
65edc68c34
[but it only shows up when building the ski simulator configuration
of ia64, so thats understandable]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Guennadi Liakhovetski
Currently probe_irq_on() on PXA will silently reconfigure all output GPIOs, that are not configured as alternate functions, for input. Avoid that. Upon CPU reset all GPIOs are configured as inputs, so, if a GPIO is configured as output, it has been done so intentionally.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus Logic EDB9315, an evaluation
board based on the Cirrus Logic EP9315 SoC, with 64M RAM, two USB host
ports, audio in/out, three serial ports, 10/100 ethernet, and IDE, VGA,
and LCD interfaces.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add the necessary kernel bits for crunch task switching.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch makes it possible to get/set a task's Crunch state via
the ptrace(2) system call.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch makes the kernel save Crunch state in userland signal frames,
so that any userland signal handler can safely use the Crunch coprocessor
without corrupting the Crunch state of the code it preempted.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
ixp23xx was including asm/hardware.h in its version of uncompress.h,
to get at the physical address of the debug UART, but this include was
causing various inline functions that are totally unrelated to the
decompressor, defined in headers in include/asm-arm/arch-ixp23xx, to
be included in the decompressor image.
Include asm/arch/ixp23xx.h instead, and move the sole inline function
in ixp23xx.h to another header.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Remove the remaining legacy __virt_to_bus__is_a_macro and
__bus_to_virt__is_a_macro defines in some ARM platforms.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
If only the S3C2412 based machines are selected,
then the regs-dsc.h does not export the S3C2412_DSC
registers as it is wrapped in CONFIG_CPU_S3C2440.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The S3C2440 and S3C2442 have an extended USB gadget
controller, so re-name the platform device to inform
the driver that it needs to change some parameters
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Back in the days when we had armo (26-bit) and armv (32-bit) combined,
we had an additional layer to the uaccess macros to ensure correct
typing. Since we no longer have 26-bit in this tree, we no longer
need this layer, so eliminate it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Remove duplicated cputable entry for 8641 (matches w/7448)
* Removed __init from function prototypes in mpc86xx.h
* Moved pci fixups into board specific code
* Moved mpc86xx_exclude_device to generic mpc86xx pci code
* Fixed sparse warnings in mpc86xx_smp.c
* Removed board specific header include from asm-powerpc/mpc86xx.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There were some common functions (mainly i/o).
Also some small white space cleanups and remove a couple of small unused
functions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we ever build a combined kernel including iSeries, then this will
be needed.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
No more StudlyCaps.
Remove from a couple of places it is no longer needed.
Use C style comments.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch allows the kernel to recognized that it was loaded at zero
and the copy down of the image is unnecessary. This is useful for
Simulators and kexec models.
On a typical 3.8 MiB vmlinux.strip this saves about 2.3 million instructions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
With this patch, kdump uses the firmware soft-reset NMI for two purposes:
1) Initiate the kdump (take a crash dump) by issuing a soft-reset.
2) Break a CPU out of a deadlock condition that is detected during kdump
processing.
When a soft-reset is initiated each CPU will enter
system_reset_exception() and set its corresponding bit in the global
bit-array cpus_in_sr then call die(). When die() finds the CPU's bit set
in cpu_in_sr crash_kexec() is called to initiate a crash dump. The first
CPU to enter crash_kexec() is called the "crashing CPU". All other CPUs
are "secondary CPUs". The secondary CPU's pass through to
crash_kexec_secondary() and sleep. The crashing CPU waits for all CPUs
to enter via soft-reset then boots the kdump kernel (see
crash_soft_reset_check())
When the system crashes due to a panic or exception, crash_kexec() is
called by panic() or die(). The crashing CPU sends an IPI to all other
CPUs to notify them of the pending shutdown. If a CPU is in a deadlock
or hung state with interrupts disabled, the IPI will not be delivered.
The result being, that the kdump kernel is not booted. This problem is
solved with the use of a firmware generated soft-reset. After the
crashing_cpu has issued the IPI, it waits for 10 sec for all CPUs to
enter crash_ipi_callback(). A CPU signifies its entry to
crash_ipi_callback() by setting its corresponding bit in the
cpus_in_crash bit array. After 10 sec, if one or more CPUs have not set
their bit in cpus_in_crash we assume that the CPU(s) is deadlocked. The
operator is then prompted to generate a soft-reset to break the
deadlock. Each CPU enters the soft reset handler as described above.
Two conditions must be handled at this point:
1) The system crashed because the operator generated a soft-reset. See
2) The system had crashed before the soft-reset was generated ( in the
case of a Panic or oops).
The first CPU to enter crash_kexec() uses the state of the kexec_lock to
determine this state. If kexec_lock is already held then condition 2 is
true and crash_kexec_secondary() is called, else; this CPU is flagged as
the crashing CPU, the kexec_lock is acquired and crash_kexec() proceeds
as described above.
Each additional CPUs responding to the soft-reset will pass through
crash_kexec() to kexec_secondary(). All secondary CPUs call
crash_ipi_callback() readying them self's for the shutdown. When ready
they clear their bit in cpus_in_sr. The crashing CPU waits in
kexec_secondary() until all other CPUs have cleared their bits in
cpus_in_sr. The kexec kernel boot is then started.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The class zero interrupt handling for spus was confusing alignment and
error interrupts, so swap them.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
