bnx2 is failing when a PCI error is detected. The error is the
following:
bnx2: Chip not in correct endian mode
bnx2: fw sync timeout, reset code = 404001d
This error was caused because the way pci_restore_state() is working
after commit 4b77b0a2ba ("PCI: Clear
saved_state after the state has been restored").
Signed-off-by: Breno Leitao<leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hardware limit to support TSOV6, just disable this feature
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a large packet gets reassembled by ip_defrag(), the head skb
accounts for all the fragments in skb->truesize. If this packet is
refragmented again, skb->truesize is not re-adjusted to reflect only
the head size since its not owned by a socket. If the head fragment
then gets recycled and reused for another received fragment, it might
exceed the defragmentation limits due to its large truesize value.
skb_recycle_check() explicitly checks for linear skbs, so any recycled
skb should reflect its true size in skb->truesize. Change ip_fragment()
to also adjust the truesize value of skbs not owned by a socket.
Reported-and-tested-by: Ben Menchaca <ben@bigfootnetworks.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
can not add camellia cipher algorithm when using "ip xfrm state" command.
Signed-off-by: Li Yewang <lyw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Add support for Mobilcom Debitel USB UMTS Surf-Stick to option driver
USB: work around for EHCI with quirky periodic schedules
USB: musb: Fix CPPI IRQs not being signaled
USB: musb: respect usb_request->zero in control requests
USB: musb: fix ISOC Tx programming for CPPI DMAs
USB: musb: Remove unwanted message in boot log
usb: amd5536udc: fixed shared interrupt bug and warning oops
USB: ftdi_sio: Keep going when write errors are encountered.
USB: musb_gadget: fix STALL handling
USB: EHCI: don't send Clear-TT-Buffer following a STALL
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/of_serial: add missing ns16550a id
bcm63xx_uart: Fix serial driver compile breakage.
tty_port: handle the nonblocking open of a dead port corner case
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Loongson: Switch from flatmem to sparsemem
MIPS: Loongson: Disallow 4kB pages
MIPS: Add missing definition for MADV_HWPOISON.
MIPS: Fix build error if __xchg() is not getting inlined.
MIPS: IP22/IP28 Disable early printk to fix boot problems on some systems.
Currently, with PAGE_SIZE_4KB, the kernel for loongson will hang on:
Kernel panic - not syncing: Attempted to kill init!
The possible reason is the cache aliases problem:
Loongson 2F has 64kb, 4 way L1 Cache, the way size is 16kb, which is bigger
then 4kb. so, If using 4kb page size, there is cache aliases problem.
To avoid this kind of problem, extra cache flushing. The 2nd possible
solution is 16kb page size which avoids cache aliases without the need for
extra cache flushes. So we disable 4kB pages until the aliasing issue is
solved.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/736/
Cc: linux-mips@linux-mips.org
Cc: zhangfx@lemote.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thanks to Joseph S. Myers for reporting this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Joseph S. Myers" <joseph@codesourcery.com>
Patchwork: http://patchwork.linux-mips.org/patch/723/
If __xchg() is not getting inlined the outline version of the function
will have a reference to __xchg_called_with_bad_pointer() which does not
exist remaining. Fixed by using BUILD_BUG_ON() to check for allowable
operand sizes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/705/
Some Debian users have reported that the kernel hangs early during boot on
some IP22 systems. Thomas Bogendoerfer found that this is due to a "bad
interaction between CONFIG_EARLY_PRINTK and overwritten prom memory during
early boot". Since there's no fix yet, disable CONFIG_EARLY_PRINTK for now.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: linux-mips@linux-mips.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Fixup last users of irq_chip->typename
Alpha: Rearrange thread info flags fixing two regressions
arch/alpha/kernel: Add kmalloc NULL tests
arch/alpha/kernel/sys_ruffian.c: Use DIV_ROUND_CLOSEST
When IMA is active, using dentry_open without updating the
IMA counters will result in free/open imbalance errors when
fput is eventually called.
Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commits 3d7a641 ("SLOW_WORK: Wait for outstanding work items belonging to a
module to clear") introduced some code to make sure that all of a module's
slow-work items were complete before that module was removed, and commit
3bde31a ("SLOW_WORK: Allow a requeueable work item to sleep till the thread is
needed") further extended that, breaking it in the process if CONFIG_MODULES=n:
CC kernel/slow-work.o
kernel/slow-work.c: In function 'slow_work_execute':
kernel/slow-work.c:313: error: 'slow_work_thread_processing' undeclared (first use in this function)
kernel/slow-work.c:313: error: (Each undeclared identifier is reported only once
kernel/slow-work.c:313: error: for each function it appears in.)
kernel/slow-work.c: In function 'slow_work_wait_for_items':
kernel/slow-work.c:950: error: 'slow_work_unreg_sync_lock' undeclared (first use in this function)
kernel/slow-work.c:951: error: 'slow_work_unreg_wq' undeclared (first use in this function)
kernel/slow-work.c:961: error: 'slow_work_unreg_work_item' undeclared (first use in this function)
kernel/slow-work.c:974: error: 'slow_work_unreg_module' undeclared (first use in this function)
kernel/slow-work.c:977: error: 'slow_work_thread_processing' undeclared (first use in this function)
make[1]: *** [kernel/slow-work.o] Error 1
Fix this by:
(1) Extracting the bits of slow_work_execute() that are contingent on
CONFIG_MODULES, and the bits that should be, into inline functions and
placing them into the #ifdef'd section that defines the relevant variables
and adding stubs for moduleless kernels. This allows the removal of some
#ifdefs.
(2) #ifdef'ing out the contents of slow_work_wait_for_items() in moduleless
kernels.
The four functions related to handling module unloading synchronisation (and
their associated variables) could be offloaded into a separate .c file, but
each function is only used once and three of them are tiny, so doing so would
prevent them from being inlined.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While building 2.6.32-rc8-git2 for Fedora I noticed the following thinko
in commit 201a15428b ("FS-Cache: Handle
pages pending storage that get evicted under OOM conditions"):
fs/9p/cache.c: In function '__v9fs_fscache_release_page':
fs/9p/cache.c:346: error: 'vnode' undeclared (first use in this function)
fs/9p/cache.c:346: error: (Each undeclared identifier is reported only once
fs/9p/cache.c:346: error: for each function it appears in.)
make[2]: *** [fs/9p/cache.o] Error 1
Fix the 9P filesystem to correctly construct the argument to
fscache_maybe_release_page().
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Xiaotian Feng <dfeng@redhat.com> [from identical patch]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [from identical patch]
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: linux-alpha@vger.kernel.org
Signed-off-by: Matt Turner <mattst88@gmail.com>
The removal of the TIF_NOTIFY_RESUME flag, commit a583f1b542
"remove unused TIF_NOTIFY_RESUME flag," resulted in incorrect
setting of the unaligned access control flags by the prctl syscall.
The re-addition of the TIF_NOTIFY_RESUME flag, commit d0420c83f3
"KEYS: Extend TIF_NOTIFY_RESUME to (almost) all architectures [try #6]"
further caused problems, namely incorrect operands to assembler code
as evidenced by:
AS arch/alpha/kernel/entry.o
arch/alpha/kernel/entry.S: Assembler messages:
arch/alpha/kernel/entry.S:326: Warning: operand out of range
(0x0000000000000406 is not between 0x0000000000000000 and
0x00000000000000ff)
Both regressions fixed by (1) rearranging TIF_NOTIFY_RESUME flag to be
in lower 8 bits of the thread info flags, and (2) making sure that
ALPHA_UAC_SHIFT matches the rearrangement of the thread info flags.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: David Howells <dhowells@redhat.com>,
Signed-off-by: Matt Turner <mattst88@gmail.com>
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).
To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On tx channel abort a cppi interrupt is generated for a short time by
setting the lowest bit of the TCPPICOMPPTR register. It is then reset
immediately by clearing the bit. When the interrupt handler is run,
it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR
registers and thus exits early without writing the TCPPIEOIR register.
It appears that this inhibits further cppi interrupts until the handler
is called by chance, f.ex. from davinci_interrupt().
By moving the unmasking of the interrupt below the writes to
TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is
necessary.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In gadget mode the answer to a control request should be followed by
a zero-length packet if the amount transferred is an exact multiple of
the endpoint's packet size and the requests has its "zero" flag set.
This patch prevents the request from being immediately removed from the
queue when a control IN transfer ends on a full packet and "zero" is set.
The next time ep0_txstate is entered, a zero-length packet is queued and
the request is removed as fifo_count is 0.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous Tx DMA is getting programmed but never getting started
for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work.
Fixing it by starting DMAs using musb_h_tx_dma_start().
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Babu Ravi <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: Robert Richter <robert.richter@amd.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix some missing author names.
They were accidentally removed by someone within Microsoft before the
files were sent for inclusion in the kernel.
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The flag ENABLE_POLLING is always enabled in original Makefile, but
accidently removed during porting to mainline kernel. The patch fixes
this bug which can cause stalled network communication. Credit needs to
go to Eric Sesterhenn <eric.sesterhenn@lsexperts.de> For pointing out a
typo in the original code as well.
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nearly every invocation of memset in drivers/staging/hv/StorVsc.c has
its arguments the wrong way around.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver missed a small API change while sitting in Ralf's tree, this
patch makes it compile again.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some drivers allow O_NDELAY of a dead port (eg for setserial to work). In that
situation we must not try to raise the carrier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: gcm - fix another complete call in complete fuction
crypto: padlock-aes - Use the correct mask when checking whether copying is required
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix sparse warning
[CIFS] Duplicate data on appending to some Samba servers
[CIFS] fix oops in cifs_lookup during net boot
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
at24: Use timeout also for read
i2c: Fix userspace_device list corruption
MAINTAINERS: Add missing i2c files
i2c/tsl2550: Fix lux value in extended mode
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Update mach-types
ARM: 5793/1: ARM: Check put_user fail in do_signal when enable OABI_COMPAT
MAINTAINERS: add maintainer information for AMBA primecell drivers
[ARM] pxa/spitz: fix compile regression on spitz
ARM: PNX4008: i2c-pnx: use the same dev_id for request_irq and free_irq
[ARM] pxa/cpufreq: fix index assignments for end marker
ARM: PNX4008: fix watchdog device driver name
[ARM] kmap: fix build errors with DEBUG_HIGHMEM enabled
Code was added to mm/higmem.c that depends on several
kmap types that powerpc does not support. We add dummy
invalid definitions for KM_NMI, KM_NM_PTE, and KM_IRQ_PTE.
According to list discussion, this fix should not be needed
anymore starting with 2.6.33. The code is commented to this
effect so hopefully we will remember to remove this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sunsu: Use sunserial_console_termios() in sunsu_console_setup().
sunsu: Pass true 'ignore_line' to console match when RSC or LOM console.
serial: suncore: Fix RSC/LOM handling in sunserial_console_termios().
serial: suncore: Add 'ignore_line' argument to sunserial_console_match().
sunsu: Fix detection of SU ports which are RSC console or control.
sunsab: Do not set sunsab_reg.cons right before registering minors.
sparc64: Fix definition of VMEMMAP_SIZE.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
b44: Fix wedge when using netconsole.
wan: cosa: drop chan->wsem on error path
ep93xx-eth: check for zero MAC address on probe, not on device open
NET: smc91x: Fix irq flags
smsc9420: prevent BUG() if ethtool is called with interface down
r8169: restore mac addr in rtl8169_remove_one and rtl_shutdown
ipv4: additional update of dev_net(dev) to struct *net in ip_fragment.c, NULL ptr OOPS
e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failure
sctp: on T3_RTX retransmit all the in-flight chunks
pktgen: Fix netdevice unregister
macvlan: fix gso_max_size setting
rfkill: fix miscdev ops
ath9k: set ps_default as false
hso: fix soft-lockup
hso: fix debug routines
pktgen: Fix device name compares
stmmac: do not fail when the timer cannot be used.
stmmac: fixed a compilation error when use the external timer
netfilter: xt_limit: fix invalid return code in limit_mt_check()
Au1x00: fix crash when trying register_netdev()
...
