SCC uart sends a break sequence each time it is stopped with the
CPM_CR_STOP_TX command. That means that each time an application closes the
serial device, a break is transmitted. To fix this, graceful tx stop is
issued for SCC.
Signed-off-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This consists of offsets fix in ..._devices.c, and update of
ppc_sys_fixup_mem_resource() function to prevent subsequent fixups
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds workaround for PPC 440GX erratum 440_43. According to
this erratum spurious MachineChecks (caused by L1 cache parity) can
happen during DataTLB miss processing. We disable L1 cache parity
checking for 440GX rev.C and rev.F
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for 85xx CDS support to arch/powerpc
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix 44x and BookE page fault handler to correctly lock PTE before
trying to pte_update() it, otherwise this PTE might be swapped out
after pte_present() check but before pte_uptdate() call, resulting in
corrupted PTE. This can happen with enabled preemption and low memory
condition.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
32-bit CHRP machines are now supported only in arch/powerpc, as are
all 64-bit PowerPC processors. This means that we don't use
Open Firmware on any platform in arch/ppc any more.
This makes PReP support a single-platform option like every other
platform support option in arch/ppc now, thus CONFIG_PPC_MULTIPLATFORM
is gone from arch/ppc. CONFIG_PPC_PREP is the option that selects
PReP support and is generally what has replaced
CONFIG_PPC_MULTIPLATFORM within arch/ppc.
_machine is all but dead now, being #defined to 0.
Updated Makefiles, comments and Kconfig options generally to reflect
these changes.
Signed-off-by: Paul Mackerras <paulus@samba.org>
PPC can use generic funcs.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This unifies the 32-bit (ARCH=ppc and ARCH=powerpc) and 64-bit idle
loops. It brings over the concept of having a ppc_md.power_save
function from 32-bit to ARCH=powerpc, which lets us get rid of
native_idle(). With this we will also be able to simplify the idle
handling for pSeries and cell.
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc32: Reorganize and complete MPC52xx initial cpu setup
This patch splits up the CPU setup into a generic part and a
platform specific part. We also add a few missing init at the
same time.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few symbols are exported twice, remove them from ppc_ksyms.c
Remove users of sys_ctrler in arch/ppc/
WARNING: vmlinux: duplicate symbol '__delay' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__up' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down_interruptible' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'sys_ctrler' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncat' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncmp' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strrchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strnlen' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strpbrk' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'memscan' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strstr' previous definition was in vmlinux
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implemented by modification of the .name field of the platform device,
when PDs with the
same names are to be used within different drivers, as
<device_name> -> <device_name>:<function>
Corresponding drivers should change the .name in struct device_driver to
reflect upper of course.
Added ppc_sys_device_disable/enable function set, making it easier to
disable all the inexistent/not utilized platform device way pdevs. By the
check of the "disabled" bit in the config field of ppc_sys_specs, disabled
platform devices will be either added/removed from the bus, or simply not
registered on it, depending on the time when disable/enable call asserted.
The default behaviour when nothing is disabled/enabled will be "all devices
are enabled", which is the same as before.
Also helper platform_notify_map function added, making assignment of
board-specific platform_info more consistent and generic.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch only deals with the serial port definitions as there is no
support for any other xilinx IP cores in the kernel tree at the moment.
Board specific configuration moved out of virtex.[ch] and into the
xparameters.h wrapper.
This also prepares for the transition to the flattened device tree model.
When the bootloader provides a device tree generated from an xparameters.h
files, the kernel will no longer need xparameters/*. The platform bus will
get populated with data from the device tree, and the device drivers will
be automatically connected to the devices. Only the bootloader (or
ppcboot) will need xparameters directly.
Signed-off-by: Grant C. Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xparameters should not be needed by anything but virtex platform code.
Move it from include/asm-ppc/ to platforms/4xx/xparameters/
This is preparing for work to remove xparameters from the dependancy tree
for most c files. xparam changes should not cause a recompile of the world.
Instead, drivers should get device info from the platform bus (populated
by the boot code)
Signed-off-by: Grant C. Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch generalizes PPC44x_PIN_SIZE by changing it to
PPC_PIN_SIZE, which can be defined by any sub-arch to automatically adjust
VMALLOC_START.
Define PPC_PIN_SIZE on 8xx, avoiding potential conflicts with the
pinned space.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds setbitsXX/clrbitsXX macro for read-modify-write operations
and converts the 8xx core and drivers to use them.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes it possible to build kernels for PReP and/or CHRP
with ARCH=ppc by removing the (non-building) powermac support.
It's now also possible to select PReP and CHRP independently.
Powermac users should now build with ARCH=powerpc instead of
ARCH=ppc. (This does mean that it is no longer possible to
build a 32-bit kernel for a G5.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add per-arch sched_cacheflush() which is a write-back cacheflush used by
the migration-cost calibration code at bootup time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 5388fb1025 made signal_32.c
use discard_lazy_cpu_state, which broke ARCH=ppc because that
uses the common signal_32.c but has its own process.c. Make ARCH=ppc
use the common process.c to fix this and to reduce the amount
of duplicated code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes pci_address_to_pio() to return an unsigned long (to be safe)
and fixes a bug in the implementation that caused it to return a bogus
IO port number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for the TQ Components TQM85xx modules. Currently the
modules TQM8540/8541/8555/8560 are supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the OF address parsers to return the IO flags
indicating the type of address obtained. It also adds a PCI
call for converting physical addresses that hit IO space into
into IO tokens, and add routines that return the translated
addresses into struct resource
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Parsing addresses extracted from Open Firmware isn't a simple matter. We
have various bits of code that try to do it in various place, including
some heuristics in prom.c that pre-parse addresses at boot and fill
device-nodes "addrs", but those are dodgy at best and I want to
deprecate them. So this patch introduces a new set of routines that
should be capable of parsing most types of addresses and translating
them into CPU physical addresses. It currently works for things on PCI
busses and ISA busses and should work on "standard" busses like the root
bus or the MacIO bus that don't put funky flags in addresses. If you
have other bus types that do use funky flags, you'll have to add new bus
type translators, which is fairly easy.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
include/asm-ppc/bseip.h is a duplicate of arch/ppc/platforms/bseip.h
and is not referenced anywhere, so get rid of it. Pointed out by
Marcelo Tosatti.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some custom cards might not need PCI, without this patch, compilation fails.
Signed-off-by: Roger Blofeld <blofeldus@yahoo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AFAIK IRQ number 0 is a perfectly valid IRQ number. But it seems there are
numerous places where it's considered to be invalid or "no irq" value. Since
that value is problematic, the IRQ mapping is changed to not use it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the not needed anymore "jumbo" member from ocp_func_emac_data.
Jumbo frame support is handled by PPC4xx EMAC driver internally now.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DMA_MODE_{READ,WRITE} are declared in asm-powerpc/dma.h and their
declarations there match the definitions. Old declarations in
ppc4xx_dma.h are not right anymore (wrong type, to start with).
Killed them, added include of asm/dma.h where needed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the FCC_PSMR_RMII defenition, which is used in fs_enet to enable
RMII mode.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Every other architecture define dma_cache_{inv,wback,wback_inv}
in asm/io.h and doing so brings us closer to ppc64.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
page_to_virt and lowmem_page_address provided equiavlent functionality
so use the more standard lowmem_page_address
This also addresses build issue in ARCH=powerpc since page_to_virt()
has been removed from include/asm-powerpc/page.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
... and also delete some that are no longer used because we already
had an include/asm-powerpc version of the header.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changed jobs and the Freescale address is no longer valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the vdso's to arch/powerpc, adds support for the 32
bits vdso to the 32 bits kernel, rename systemcfg (finally !), and adds
some new (still untested) routines to both vdso's: clock_gettime() with
support for CLOCK_REALTIME and CLOCK_MONOTONIC, clock_getres() (same
clocks) and get_tbfreq() for glibc to retreive the timebase frequency.
Tom,Steve: The implementation of get_tbfreq() I've done for 32 bits
returns a long long (r3, r4) not a long. This is such that if we ever
add support for >4Ghz timebases on ppc32, the userland interface won't
have to change.
I have tested gettimeofday() using some glibc patches in both ppc32 and
ppc64 kernels using 32 bits userland (I haven't had a chance to test a
64 bits userland yet, but the implementation didn't change and was
tested earlier). I haven't tested yet the new functions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ppc32 and ppc64 versions of cacheflush.h were almost identical.
The two versions of cache.h are fairly similar, except for a bunch of
register definitions in the ppc32 version which probably belong better
elsewhere. This patch, therefore, merges both headers. Notable
points:
- there are several functions in cacheflush.h which exist only
on ppc32 or only on ppc64. These are handled by #ifdef for now, but
these should probably be consolidated, along with the actual code
behind them later.
- Confusingly, both ppc32 and ppc64 have a
flush_dcache_range(), but they're subtly different: it uses dcbf on
ppc32 and dcbst on ppc64, ppc64 has a flush_inval_dcache_range() which
uses dcbf. These too should be merged and consolidated later.
- Also flush_dcache_range() was defined in cacheflush.h on
ppc64, and in cache.h on ppc32. In the merged version it's in
cacheflush.h
- On ppc32 flush_icache_range() is a normal function from
misc.S. On ppc64, it was wrapper, testing a feature bit before
calling __flush_icache_range() which does the actual flush. This
patch takes the ppc64 approach, which amounts to no change on ppc32,
since CPU_FTR_COHERENT_ICACHE will never be set there, but does mean
renaming flush_icache_range() to __flush_icache_range() in
arch/ppc/kernel/misc.S and arch/powerpc/kernel/misc_32.S
- The PReP register info from asm-ppc/cache.h has moved to
arch/ppc/platforms/prep_setup.c
- The 8xx register info from asm-ppc/cache.h has moved to a
new asm-powerpc/reg_8xx.h, included from reg.h
- flush_dcache_all() was defined on ppc32 (only), but was
never called (although it was exported). Thus this patch removes it
from cacheflush.h and from ARCH=powerpc (misc_32.S) entirely. It's
left in ARCH=ppc for now, with the prototype moved to ppc_ksyms.c.
Built for Walnut (ARCH=ppc), 32-bit multiplatform (pmac, CHRP and PReP
ARCH=ppc, pmac and CHRP ARCH=powerpc). Built and booted on POWER5
LPAR (ARCH=powerpc and ARCH=ppc64).
Built for 32-bit powermac (ARCH=ppc and ARCH=powerpc). Built and
booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built and booted
on G5 (ARCH=powerpc)
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges current.h. This is a one-big-ifdef merge, but both
versions are so tiny, I think we can live with it. While we're at it,
we get rid of the fairly pointless redirection through get_current()
in the ppc64 version.
Built and booted on POWER5 LPAR (ARCH=powerpc & ARCH=ppc64). Built
for 32-bit pmac (ARCH=powerpc & ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having already merged the ppc and ppc64 versions of signal.c, this
patch finishes the job by merging signal.h. The two versions were
almost identical already. Notable changes:
- We use BITS_PER_LONG to correctly size sigset_t
- Remove some uneeded #includes and struct forward
declarations. This does mean adding an include to signal_32.c which
relied on the indirect inclusion of sigcontext.h
- As the ppc64 version, the merged signal.h has prototypes for
do_signal() and do_signal32(). Thus remove extra prototypes from
ppc_ksyms.c which had them directly.
Built and booted on POWER5 LPAR (ARCH=ppc64 and ARCH=powerpc). Built
for 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPC834x uses the gianfar network driver which now uses the new phylib. We
need to update the platform code to create a gianfar platform MDIO bus and
pass the right intializations to the gianfar driver to make things work
again.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is very simple with it being almost all ppc32 with just a couple
of common defines.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xmon() prototype is inconsistent between ARCH=ppc and ARCH=powerpc,
thus causing ARCH=ppc build breakage.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Building a PowerMac kernel with ARCH=powerpc causes a bunch of warnings,
this fixes some of them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the ability to the SMU driver to recover missing
calibration partitions from the SMU chip itself. It also adds some
dynamic mecanism to /proc/device-tree so that new properties are visible
to userland.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds PPC32 RIO support. Init code for the MPC85xx RIO ports and glue for the
STx GP3 board to use it.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cleanup PPC40x eval boards (bubinga, walnut and sycamore) to support U-Boot
as bootloader. The OpenBIOS bd_info struct is not used in the kernel
anymore (only U-Boot now).
uImage (U-Boot) tested on walnut, sycamore and bubinga
zImage (OpenBIOS) tested on sycamore, bubinga and ebony
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the AMCC PowerPC 440SPe SoC, including PCI Express in root
port mode.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SP SoC has two Processor Local Bus (PLB) segments (a
high-throughput segment and a low-latency segment). Fix our PLB register
definitions to cope with this, and add code to dump the status of both
segments when a machine check occurs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PowerPC 440SPe supports up to 16 GB of RAM, and therefore its IO registers
are at 0x4_xxxx_xxxx instead of being at 0x1_xxxx_xxxx like most other PPC 440
chips. To allow for this, this patch moves the definition of the ERPN used
for mapping UART0 from being hard-coded in the head_44x.S assembly code to
being defined in ibm44x.h.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds exception table entries for I/O instructions on and
changes MachineCheckException() slightly to cover 8xx specifics (on
8xx the MCE can be generated while executing the IO access instruction
itself, which is not the case on PowerMac's, as the comment on traps.c
details).
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge include/asm-ppc/kexec.h and include/asm-ppc64/kexec.h.
The only thing that's really changed is that we now allocate crash_notes
properly on PPC32. It's address is exported via sysfs, so it's not correct
for it to be a pointer.
I've also removed some of the "we don't use this" comments, because they're
wrong (or perhaps were referring only to arch code).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
This patch merges the ppc32 and ppc64 versions of futex.h, essentially
by taking the ppc64 version as the powerpc version. The old ppc32
version did not implement the futex_atomic_op_inuser() callback (it
always returned -ENOSYS), so FUTEX_WAKE_OP would not work on ppc32.
In fact the ppc64 version of this function is almost suitable for
ppc32 as well - the only change needed is to extend ppc_asm.h with a
macro expanding to to the right pseudo-op to store a pointer (either
".long" or ".llong").
Built and booted on pSeries. Built for 32-bit powermac.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's a revised version. This re-introduces the set_bits() function
from ppc64, which I removed because I thought it was unused (it exists
on no other arch). In fact it is used in the powermac interrupt code
(but not on pSeries).
- We use LARXL/STCXL macros to generate the right (32 or 64 bit)
instructions, similar to LDL/STL from ppc_asm.h, used in fpu.S
- ppc32 previously used a full "sync" barrier at the end of
test_and_*_bit(), whereas ppc64 used an "isync". The merged version
uses "isync", since I believe that's sufficient.
- The ppc64 versions of then minix_*() bitmap functions have changed
semantics. Previously on ppc64, these functions were big-endian
(that is bit 0 was the LSB in the first 64-bit, big-endian word).
On ppc32 (and x86, for that matter, they were little-endian. As far
as I can tell, the big-endian usage was simply wrong - I guess
no-one ever tried to use minixfs on ppc64.
- On ppc32 find_next_bit() and find_next_zero_bit() are no longer
inline (they were already out-of-line on ppc64).
- For ppc64, sched_find_first_bit() has moved from mmu_context.h to
the merged bitops. What it was doing in mmu_context.h in the first
place, I have no idea.
- The fls() function is now implemented using the cntlzw instruction
on ppc64, instead of generic_fls(), as it already was on ppc32.
- For ARCH=ppc, this patch requires adding arch/powerpc/lib to the
arch/ppc/Makefile. This in turn requires some changes to
arch/powerpc/lib/Makefile which didn't correctly handle ARCH=ppc.
Built and running on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges ppc32 and ppc64 versions of ipcbuf.h. The merge is
essentially trivial, since the structure defined in each version was
already identical. Only wrinkle is that the merged version now
includes linux/types.h in order to get the fixed width integer types.
In fact, the old versions probably should have been including that
anyway, since the file uses various __kernel_*_t types.
Built and booted on G5, built for 32-bit pmac, but not booted, since
the merge tree currently doesn't boot there.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
__MUTEX_INITIALIZER() has no users, and equates to the more commonly used
DECLARE_MUTEX(), thus making it pretty much redundant. Remove it for good.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add sem_is_read/write_locked functions to the read/write semaphores, along the
same lines of the *_is_locked spinlock functions. The swap token tuning patch
uses sem_is_read_locked; sem_is_write_locked is added for completeness.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a numbers of issues regarding to that both 8xx and 82xx
began to use ppc_sys model:
- Platform is now identified by default deviceless SOC, if no
BOARD_CHIP_NAME is specified in the bard-specific header. For the list
of supported names refer to (arch/ppc/syslib/) mpc8xx_sys.c and
mpc82xx_sys.c for 8xx and 82xx respectively.
- Fixed a bug in identification by name - if the name was not found,
it returned -1 instead of default deviceless ppc_spec.
- fixed devices amount in the 8xx platform system descriptions
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates the 85xx platform code to support the new PHY Layer.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <Kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a nvram acccess method, similar to
arch/ppc64/kernel/pSeries_nvram.c tested on CHRP B50.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the phys_mem_access_prot() function to take a pfn instead of an
address. This allows mmap64() to work on /dev/mem for addresses above 4G
on 32-bit architectures. We start with a pfn in mmap_mem(), so there's no
need to convert to an address; in fact, it's actively bad, since the
conversion can overflow when the address is above 4G.
Similarly fix the ppc32 page_is_ram() function to avoid a conversion to an
address by directly comparing to max_pfn. Working with max_pfn instead of
high_memory fixes page_is_ram() to give the right answer for highmem pages.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Save for the header #define, ppc32 and ppc64 versions of parport.h are
identical. This patch merges them.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent merge of fpu.S broken the handling of fpscr for
ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted,
leading to strange random application crashes.
The confusion arises, because the thread_struct has (and requires) a
64-bit area to save the fpscr, because we use load/store double
instructions to get it in to/out of the FPU. However, only the low
32-bits are actually used, so we want to treat it as a 32-bit quantity
when manipulating its bits to avoid extra load/stores on 32-bit. This
patch replaces the current definition with a structure of two 32-bit
quantities (pad and val), to clarify things as much as is possible.
The 'val' field is used when manipulating bits, the structure itself
is used when obtaining the address for loading/unloading the value
from the FPU.
While we're at it, consolidate the 4 (!) almost identical versions of
cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S,
arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S,
arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The
new version takes a pointer to thread_struct and applies the correct
offset itself, rather than a pointer to the fpscr field itself, again
to avoid confusion as to which is the correct field to use.
Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S
code, which it previously did not.
Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc
and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y).
Booted on G5 (ARCH=powerpc) and things which previously fell over no
longer do.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge ppc32 and ppc64 versions of thread_info.h. They were pretty
similar already, the chief changes are:
- Instead of inline asm to implement current_thread_info(),
which needs to be different for ppc32 and ppc64, we use C with an
asm("r1") register variable. gcc turns it into the same asm as we
used to have for both platforms.
- We replace ppc32's 'local_flags' with the ppc64
'syscall_noerror' field. The noerror flag was in fact the only thing
in the local_flags field anyway, so the ppc64 approach is simpler, and
means we only need a load-immediate/store instead of load/mask/store
when clearing the flag.
- In readiness for 64k pages, when THREAD_SIZE will be less
than a page, ppc64 used kmalloc() rather than get_free_pages() to
allocate the kernel stack. With this patch we do the same for ppc32,
since there's no strong reason not to.
- For ppc64, we no longer export THREAD_SHIFT and THREAD_SIZE
via asm-offsets, thread_info.h can now be safely included in asm, as
on ppc32.
Built and booted on G4 Powerbook (ARCH=ppc and ARCH=powerpc) and
Power5 (ARCH=ppc64 and ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This declares powersave_nap in system.h and makes it an int everywhere,
fixes typos for the maple platform, fixes a couple of places where
I missed removing the last two arguments from a message_pass function,
and makes ppc64 consistent with ppc32 in the type of the
pci_bridge.cfg_data field.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Except for smu.h, which moved from asm-ppc64 to asm-powerpc, all
of these moved from asm-ppc to asm-powerpc. In each case the
asm-ppc64 version (if there was one) was just a single line
including the asm-ppc version.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges types.h into include/asm-powerpc. The only real change is
the removal of the include of linux/config.h from the 32-bit version - it
doesn't appear to be necessary.
This patch has been built on several different 32 and 64-bit platforms,
and booted on mpc8540_ads.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patches the ppc32 and ppc64 versions of the headers and .c files
with helper functions for manipulating the performance counting
hardware. As a side effect, it removes use of the term "perfmon" from
ppc32, thus avoiding confusion with the unrelated performance counter
interface from HP Labs also called "perfmon".
Built, but not booted, for g5, pSeries, iSeries, and 32-bit Powermac
with both ARCH=powerpc and ARCH=ppc{,64} as appropriate.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Glibc is about to get some new high precision timer stuff that relies on
the standard timebase of the PPC architecture.
However, some (rare & old) CPUs do not have such timebase and it is a
bit annoying to have your stuff just crash because you are running on
the wrong CPU...
This exposes to userland a CPU feature bit that tells that the current
processor doesn't have a standard timebase. It's negative logic so that
glibc will still "just work" on older kernels (it will just be unhappy
on those old CPUs but that doesn't really matter as distro tend to
update glibc & kernel at the same time).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes up a variety of minor problems in compiling with ARCH=ppc
arising from using the merged versions of various header files.
A lot of the changes are just adding #include <asm/machdep.h> to
files that use ppc_md or smp_ops_t.
This also arranges for us to use semaphore.c, vecemu.c, vector.S and
fpu.S from arch/powerpc/kernel when compiling with ARCH=ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds register definitions from the ppc64 processor.h to reg.h,
and makes a single merged processor.h. I moved __is_processor from
the ppc64 system.h to the merged reg.h along with the PVR register
constants.
Signed-off-by: Paul Mackerras <paulus@samba.org>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This also creates merged versions of do_init_bootmem, paging_init
and mem_init and moves them to arch/powerpc/mm/mem.c. It gets rid
of the mem_pieces stuff.
I made memory_limit a parameter to lmb_enforce_memory_limit rather
than a global referenced by that function. This will require some
small changes to ppc64 if we want to continue building ARCH=ppc64
using the merged lmb.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use idle_power4.S from ppc64 as we are not going to support
32 bit power4 in the merged tree.
Merge ppc64 traps.c into powerpc traps.c:
use ppc64 versions of exception routine names
(as they don't have StudlyCaps)
make all the versions if die() have the same
prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Merged cputable.h between ppc32 and ppc64. In doing this removed support
for the BEGIN_FTR_SECTION/END_FTR_SECTION macros in C code since they
dont compile correctly. C code should use cpu_has_feature(). This is
based on Arnd Bergmann's initial patch.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge byteorder.h
Essentially adopts the 64-bit version of this file. The 32-bit version had
been using unsigned ints for arguments/return values that were actually
only 16 bits - the new file uses __u16 for these items as in the 64-bit
version of the header. The order of some of the asm constraints
in the 64-bit version was slightly different than the 32-bit version,
but they produce identical code.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Complete moving arch/ppc64/kernel/mpic.h,
include/asm-ppc/reg.h, include/asm-ppc64/kdebug.h
and include/asm-ppc64/kprobes.h
Add arch/powerpc/platforms/Makefile and use it from
arch/powerpc/Makefile
Introduce OLDARCH temporarily so we can point back to
the originating architecture
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge semaphore.h
Adopted the ppc64 version of semaphore.h. The 32-bit version used
smp_wmb(), but recent updates to atomic.h mean this is no longer required.
The 64-bit version made use of unlikely(), which has been retained in the
combined version.
This patch requires the recent atomic.h patch.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge asm-ppc*/rwsem.h into include/asm-powerpc.
Removed smp_*mb() memory barriers from the ppc32 code
as they are now burried in the atomic_*() functions as
suggested by Paul, implemented by Arnd, and pushed out
by Becky. I am not the droid you are looking for.
This patch depends on Becky's atomic.h merge patch.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge atomic.h and memory.h into powerpc
Merged atomic.h into include/powerpc. Moved asm-style HMT_ defines from
memory.h into ppc_asm.h, where there were already HMT_defines; moved c-style
HMT_ defines to processor.h. Renamed memory.h to synch.h to better reflect
its contents.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <linuxppc@jdl.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge asm-ppc*/seccomp.h. Drop TIF_32BIT check.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The spinlock_types.h merge renamed the structure for raw_spinlock_t to
match ppc64. In doing so some of the spinlock macros/functions needed to
be updated to match. Apparently, this seems to only be caught when
building power3.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SMU is the "system controller" chip used by Apple recent G5 machines
including the iMac G5. It drives things like fans, i2c busses, real time
clock, etc...
The current kernel contains a very crude driver that doesn't do much more
than reading the real time clock synchronously. This is a completely
rewritten driver that provides interrupt based command queuing, a userland
interface, and an i2c/smbus driver for accessing the devices hanging off
the SMU i2c busses like temperature sensors. This driver is a basic block
for upcoming work on thermal control for those machines, among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merged hw_irq.h between ppc32 & ppc64. Added support to use the Book-E
wrtee[i] instructions that allow modifying MSR[EE] atomically.
Additionally, added get_irq_desc() macros to ppc32 to allow mask_irq(),
unmask_irq(), and ack_irq() to be common between ppc32 & ppc64.
Note: because 64-bit Book-E implementations only have a 32-bit MSR the
macro's for Book-E need to come before the PPC64 macro's to ensure the
right thing happends for 64-bit Book-E processors.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges the asm-ppc*/dma.h files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As recently done by Russell King for ARM, commit
4732efbeb9 introduces a generic asm/futex.h copied
along most arches, which includes a "-ENOSYS support" to be changed if needed.
However, it includes an unused var (taken from the "real" version) which GCC
warns about.
Remove it from all arches having that file version (i.e. same GIT id).
$ git-diff-tree -r HEAD
and
$ git-ls-tree -r HEAD include/|grep 9feff4ce14
may be more interesting than looking at the patch itself, to make sure I've
just copied the arm header to all other archs having the original dummy version
of this file.
Cc: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge asm-ppc*/vga.h
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc/ppc64: Merge elf.h into include/asm-powerpc
Merge elf.h into a single include file for 32 and 64-bit ppc platforms. This
patch has been tested on 32-bit and built on 64-bit platforms.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Becky Bruce <Becky.Bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc32/ppc64: Merge bug.h into include/asm-powerpc
This patch merges bug.h into include/asm-powerpc. Changed the data
structure for bug_entry such that line is always an int on both 32 and
64-bit platforms; removed casts to int from the 64-bit trap code to
reflect this.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Becky Bruce <Becky.Bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a revised patch to merge asm-ppc*/hardirq.h.
It removes some unnecessary #includes, but then requires
the addition of #include <asm/irq.h> in PPC32's hw_irq.h
much like ppc64 already does. Furthermore, several
unnecessary #includes were removed from some ppc32 boards
in order to break resulting bad #include cycles.
Builds pSeries_defconfig and all ppc32 platforms except
the already b0rken bseip.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename and slightly modify {request,free}_perfmon_irq in the ppc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge asm-ppc/posix_types.h and asm-ppc64/posix_types.h.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
