Allows compiling g_ether in and fixes a typo with MUSB_HDRC
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the PXA 25x UDC board-independent infrastructure for VBUS sensing
and the D+ pullup. The original code evolved from rather bizarre support on
Intel's "Lubbock" reference hardware, so that on more sensible hardware it
doesn't work as well as it could/should.
The change is just to teach the UDC driver how to use built-in PXA GPIO pins
directly. This reduces the amount of board-specfic object code needed, and
enables the use of a VBUS sensing IRQ on boards (like Gumstix) that have one.
With VBUS sensing, the UDC is unclocked until a host is actually connected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/Kconfig:87:warning: 'select' used by config symbol 'USB_OHCI_HCD' refer to undefined symbol 'I2C_PNX'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
inlined is the patch that adds basic support for USB OHCI controller
support for PNX4008 Philips PNX4008 ARM board. Due to HW design, it
depends on I2C driver for PNX4008 which I've recetnly posted to LKML and
i2c at lm-sensors.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With the newer Samsung S3C2412 and S3C2413 SoC devices,
the 48MHz USB clock has been given an individual gate
into the USB OHCI and gadget blocks.
This clock is called usb-bus-clock, and we need to
replace the old use of the USB PLL (upll) directly
with the new usb-bus-host.
The S3C2410 clock driver has been updated already to
provide a virtual clock which is a child of the UPLL
to maintain compatibility. The S3C2412 clock driver
correctly enables the PLL when either usb-bus clock
is active.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This teaches OHCI to use the root hub status change (RHSC) IRQ, bypassing
root hub timers most of the time and switching over to the "new" root hub
polling scheme. It's complicated by the fact that implementations of OHCI
trigger and ack that IRQ differently (the spec is vague there).
Avoiding root hub timers helps mechanisms like "dynamic tick" leave the
CPU in lowpower modes for longer intervals.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a re-diffed version of one originally sent by Jan Mate
<mate@fiit.stuba.sk>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as781) adds an entry to unusual_devs.h for the Lacie DVD+-RW
drive. Apparently its USB interface has requirements similar to the
Genesys Logic interface; it doesn't like data to be sent too soon after
a command.
This fixes Bugzilla #6817.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This eliminates the i_blksize field from struct inode. Filesystems that want
to provide a per-inode st_blksize can do so by providing their own getattr
routine instead of using the generic_fillattr() function.
Note that some filesystems were providing pretty much random (and incorrect)
values for i_blksize.
[bunk@stusta.de: cleanup]
[akpm@osdl.org: generic_fillattr() fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Rougly half of callers already do it by not checking return value
* Code in drivers/acpi/osl.c does the following to be sure:
(void)kmem_cache_destroy(cache);
* Those who check it printk something, however, slab_error already printed
the name of failed cache.
* XFS BUGs on failed kmem_cache_destroy which is not the decision
low-level filesystem driver should make. Converted to ignore.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This teaches several USB host controller drivers to treat PRETHAW as a chip
reset since the controller, and all devices connected to it, are no longer in
states compatible with how the snapshotted suspend() left them.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a memory leak and a kernel oops when trying to unload
the driver, due to an unbalanced cleanup.
Thanks Ivar Jensen for spotting my mistake.
Signed-off-by: Henk Vergonet <henk.vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A sufficiently-large number of USB serial devices causes a reference leak
when /proc/tty/drivers/usbserial is read.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds a new device ID for the Gamma Scout Geiger counter
device.
Signed-off-by: Ralf Schlatterbeck <rsc@runtux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is support USB20SVGA-WH & USB20SVGA-DG of the sisusb device.
As for this device, Device ID is different according to the color of the
product. A blue device is supported. However, a green, white device is
not supported.
http://www.lubic.jp/uv_method.html ( Japanese only ) .
Green, white USB20SVGA comes to work by applying the patch .
And, it be able to use three USB20SVGA( Blue , Green , White ).
Signed-off-by: Nobuhiro Iwamatsu <hemamu@t-base.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Fri, Sep 01, 2006 at 01:58:18AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.18-rc4-mm3:
>...
> +gregkh-usb-hid-core.c-adds-all-gtco-calcomp-digitizers-and-interwrite-school-products-to-blacklist.patch
>...
> USB tree updates.
>...
The GNU C compiler spotted the following bug:
<-- snip -->
...
CC drivers/usb/input/hid-core.o
/home/bunk/linux/kernel-2.6/linux-2.6.18-rc5-mm1/drivers/usb/input/hid-core.c:1446:1: warning: "USB_DEVICE_ID_GTCO_404" redefined
/home/bunk/linux/kernel-2.6/linux-2.6.18-rc5-mm1/drivers/usb/input/hid-core.c:1445:1: warning: this is the location of the previous definition
...
<-- snip -->
This patch fixes this cut'n'paste error.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When skipping to the last TD of an URB, go to the _last_ entry in the
list instead of the _first_ entry (as780). This fixes Bugzilla #6747
and possibly others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is support LD-USB20 of the USB LAN device.
http://www2.elecom.co.jp/products/LD-USB20.html ( Japanese only )
I am using this device.
And, I confirmed work by using this patch.
Signed-off-by: Nobuhiro Iwamatsu <hemamu@t-base.ne.jp>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to wait until any currently-running handler has completed. Fixes an
unplug-time oops reported by "Miles Lane" <miles.lane@gmail.com>.
Cc: "Petko Manolov" <petkan@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This entry was sent in by Emmanuel Vasilakis <evas@forthnet.gr>, turned
into a patch by yours truly.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the Kyocera Finecam L3 entry in unusual devices
originally submitted by Michael Krauth <michael.krauth@web.de> and
Alessandro Fracchetti <al.fracchetti@tin.it> given that Gerriet
<ger.haw@gmx.de> finds he doesn't need it and Alessandro confirms it
isn't needed anymore as well.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unlike other sorts of endpoint queues, Isochronous queues don't stop
when an error is encountered. This patch (as772) fixes the scanning
routine in uhci-hcd, to make it keep on going when it finds an Iso
error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new spinlock debug code turned up a spinlock recursion bug in the
Ethernet gadget driver on a disconnect path; it would show up with any
UDC driver where the cancellation of active requests was synchronous,
rather than e.g. delayed until a controller's completion IRQ.
That recursion is fixed here by creating and using a new spinlock to
protect the relevant lists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds all GTCO CalComp Digitizers and InterWrite School Products to
hid-core.c blacklist.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The existing unusual_devs entry for the UCR-61S2B appears to have too
wide a revision range. It matches at least one device that doesn't
respond to the initialization sequence. Perhaps the sequence needs to
be updated, or perhaps something else can be done. For now, this patch
(as764) restricts the range to include only the revision mentioned in
the original comment.
This resolves (for now!) Bugzilla entry #6950.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes support for a clone of Nokia DKU-5 cable made by Ours
Technology Inc, as it turned out that the cable does not use the pl2303
chip, but OTI-6858 chip which is not compatible with the pl2303.
Signed-off-by: Tomasz Kazmierczak <tomek.fizyk@op.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was pointed out by Adrian Bunk <bunk@stusta.de>, as found by the Coverity Checker.
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In my quest to try and figure out why test 14 (control write) doesn't
work with my EZ-USB board, I noticed that sometimes testusb reported
no error even though the kernel log complained "byte 0 is 0 not 2" etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I write a patch for ipaq.c.
Would you like to add upstream tree ?
This patch enables a support of "SHARP W-ZERO3(WS004SH)" and "SHARP W-ZERO3[es](WS007SH)".
From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
appletouch uses urb->transfer_dma after having freed the urb, this shows
up only if the system is compiled with slab debugging. This patch fixes
it by reordering the free calls.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch has removed a unbalanced #endif from ohci-au1xxx.c .
Please apply before 2.6.18 release.
Error message was:
In file included from drivers/usb/host/ohci-hcd.c:909:
drivers/usb/host/ohci-au1xxx.c:113:2: #endif without #if
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as763) adds an unusual_devs entry for the A-VOX WSX-300ER MP3
player.
From: David Kuehling <dvdkhlng@gmx.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
By using milliseconds instead of jiffies to calculate acceleration
factor we make the code immune to changes in HZ.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When emulating button toggle drivers need to send input_sync()
between 'down' and 'up' events, otherwise some users might miss
keypress because device's state is only considered finalized
after EV_SYN/SYN_REPORT is received.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This reverts c182274ffe commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts bd00949647 commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apparently some UHCI controllers change the value of the Short Packet
Detect (SPD) bit in the TD status word -- presumably when they receive a
short packet. This patch (as759) changes uhci-hcd to avoid assuming
that the bit is unchanged; in fact, the driver no longer looks at SPD at
all.
This fixes the second problem reported in Bugzilla #6752.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is another unusual_devs entry (as760) for another Nokia device,
this time the 3250.
From: Mario Rettig <mariorettig@web.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as756) fixes a bug in dummy-hcd found by the lockdep
checker. In one of the code paths, the driver did not disable
interrupts before calling a request completion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If USB=m, USB_GADGET=y, the option USB_GADGET_DUMMY_HCD mustn't be
offered since selecting it results in a compile error.
This patch fixes kernel Bugzilla #6534 reported by Toralf Frster.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When HZ is set to 250 (new default) or 100, the time span during which
repeated events from the device are ignored could be too small due to
ms->jiffies rounding. This causes the auto repeat to kick in early making
it impossible for the user to generate individual press/release events.
Increate the timeout to compensate.
Signed-off-by: Marko Macek <Marko.Macek@gmx.net>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The RTL8150 driver currently crashes the kernel if the USB lead is unplugged
while the device is active. The attached patch adds error handling to
tell the network layer that the device has gone away when the device is
unplugged. With this patch, the device can be plugged and unplugged
to one's hearts' content, without crashing anything.
Oh, I've also added rudimentary suspend and resume methods.
Signed-off-by: Peter Chubb <peter@gelato.unsw.edu.au>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This entry has been a mystery for some time. I had sent this patch as an
RFC a while ago, and now we've had two reports of this not being needed,
so I'm removing it.
In the event there are reports of breakage, we should revert this patch,
but add a US_FL_NEED_OVERRIDE flag.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new unusual_devs flag for when usb-storage needs to ignore
a device that it would otherwise claim.
We need to ignore the ZyXEL G220F as it is a virtual CDROM drive which
includes the windows driver for this USB-WLAN adapter. After the windows
driver is installed on a windows system, it converts it into a WLAN adapter
(by ejecting the virtual disc).
The virtual CDROM is of no interest to Linux users. The zd1211rw driver will
automatically perform the eject operation, we just need to ensure that
usb-storage does not claim the device.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Can you add the USB IDs for the Belkin USB Serial adapter (P/N F5U257)
to the pl2303 driver in the Linux Kernel? Are you the appropriate person
to approach for this?
I recently purchased a Belkin USB Serial adapter (P/N F5U257) and found
that it didn't work. After a bit of experimentation I found that it
works with the pl2303 driver once the ID has been added. See attached
patch to fix this. Also attached is the output from lsusb -v just in
case you require any information from there.
From: Kim Oldfield <luv@oldfield.wattle.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's a short patch which adds one PID to the set of devices
supported by the ftdi_sio driver. The device in question is a
DLP module used as part of a ham radio USB-to-packet adapter.
From: Dave Platt <dplatt@radagast.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This small patch enables a support of "SHARP WS003SH".
"SHARP WS003SH" (usullary called "W-ZERO3") is most polular All-in-one handheld
CellPhone-plus-WindowsMobile5.0 in Japan.
"SHARP WS003SH" has two modes, "Modem" and "ActiveSync".
But, "ActiveSync" mode uses NDIS connection.
Therefore, ipaq.c can only support "Modem" mode.
http://www.sharp.co.jp/ws/ (Japanese Site)
http://greggman.com/edit/editheadlines/2005-12-24.htm
From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The high-speed USB SOC only exists on MPC834x family not MPC83xx family.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The short driver names were not unique,
which prevented the driver from actually loading.
Also, one of the ioctl pointers was missing.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OHCI updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, OHCI can be a source of system wakeup events
(remote wakeup, device connect/disconnect, etc)
And minor cleanups.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UDC updates for AT91 series processors:
- Get ready for at91sam926x processors (ARMv5tej not ARMv4t)
- Suspend/resume support now behaves properly
- In "standby" mode, UDC can be a source of system wakeup events
(host resume, device connect/disconnect, etc)
- Fix IRQ storming issues, seemingly related to clock disabling
changes that went in a while back
And minor cleanups, especially whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB serial outside of the kernel tree can not build properly due to
usb-serial.h being buried down in the source tree. This patch moves the
location of the file to include/linux/usb and fixes up all of the usb
serial drivers to handle the move properly.
Cc: Sergei Organov <osv@javad.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anydata is using usb_serial_generic_write_bulk_callback() for its
read URB, but it should use usb_serial_generic_read_bulk_callback()
instead (it's a read URB, isn't it?).
Reported by Jon K Hellan <hellan@acm.org>.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent section changes broke gadget builds on some platforms. This patch
is the best fix that's available until better section markings exist:
- There's a lot of cleanup code that gets used in both init and exit paths;
stop marking it as "__exit".
(Best fix for this would be an "__init_or_exit" section marking, putting
the cleanup in __init when __exit sections get discarded else in __exit.)
- Stop marking the use-once probe routines as "__init" since references
to those routines are not allowed from driver structures. They're now
marked "__devinit", which in practice is a net lose.
(Best fix for this is likely to separate such use-once probe routines
from the driver structure ... but in general, all busses that aren't
hotpluggable will be forced to waste memory for all probe-only code.)
In general these broken section rules waste an average of two to four kBytes
per driver of code bloat ... because none of the relevant code can ever be
reused after module initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the Testo USB interface to the list of devices
recognized by the ftdi_sio module. This device is based on a FT232BL
chip, and is used as an interface to get data from digital sensors
(thermometer, etc). See http://www.testo.com/
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as749) extends the unusual_devs entry for the Sony DSC-T1 and
T5 to cover the H5 as well.
From: Lars Jacob <jacob.lars@googlemail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as748) adds an unusual_devs entry for the Nokia E61 mobile
phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as745) adds an unusual_devs entry for the Nokia N91, just like
the entry for the N80 added a couple of weeks ago. Apparently Nokia isn't
using very good firmware these days...
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I just got a "ZyXEL Prestige USB Adapter" that is actually RTL8150
adapter. Here is the relevant /proc/bus/usb/devices output (after
adding the vendor/product IDs to the driver):
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=119 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0586 ProdID=401a Rev= 1.00
S: Manufacturer=ZyXEL
S: Product=Prestige USB Adapter
S: SerialNumber=1027
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=120mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=rtl8150
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
This patch adds the ZyXEL vendor ID to the rtl8150.c driver. The
device has absolutely no identifying marks on the outside for model
type, just a serial number, and I can't find anything on ZyXEL's
website, so I called the product ID PRODUCT_ID_PRESTIGE to match the
product string.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Acked-by: <petkan@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is to get the WiseGroup.,Ltd SmartJoy Dual Plus PS2-to-USB
Adapter [0x6677:0x8802] correctly detected. It sets the NOGET and
MULTI_INPUT quirks to make 2 joystick nodes appear in stead of only
one.
(As of yet, only confirmed working by myself.)
Signed-off-by: Navaho Gunleg <navahogunleg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The below patch fixes the ipw module in kernel 2.6.17 for me; without
this change it simply does not work at all (all but the first writes are
refused because write_urb_busy is always 1).
This problem was there in 2.6.15 as well, but at that point I used the
(updated) ipw.c, version 0.4, from
http://www.neology.co.za/products/opensource/ipwireless/ which no longer
compiles with 2.6.17. It can be made to after a few changes but
obviously it's easier if the built-in ipw driver works instead of having
to download one from the neology site.
From: Bart Oldeman <bartoldeman@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Devfs is gone. We can remove that information.
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove destructor and call kmem_cache_create with NULL for the destructor.
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds configurable waiting periods to the ipaq connection code. These are
not needed when the pocketpc device is running normally when plugged in,
but they need extra delays if they are physically connected while
rebooting.
There are two parameters :
* initial_wait : this is the delay before the driver attemts to start the
connection. This is needed because the pocktpc device takes much
longer to boot if the driver starts sending control packets too soon.
* connect_retries : this is the number of times the control urb is
retried before finally giving up. The patch also adds a 1 second delay
between retries.
I'm not sure if the cases where this patch is useful are general enough
to include this in the kernel.
Signed-off-by: Frank Gevaerts <frank.gevaerts@fks.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes several problems in the ipaq.c driver with connecting
and disconnecting pocketpc devices:
* The read urb stayed active if the connect failed, causing nullpointer
dereferences later on.
* If a write failed, the driver continued as if nothing happened. Now it
handles that case the same way as other usb serial devices (fix by
Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>)
Signed-off-by: Frank Gevaerts <frank.gevaerts@fks.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In a rare and all-but-unused path, the EHCI driver could reuse a variable
in a way that'd make trouble. Specifically, if the first root hub port
gets an overcurrent event (rare) during a remote wakeup scenario (all but
unused in today's Linux, except for folk working with suspend-to-RAM and
similar sleep states), that would look like a fatal error which would shut
down the controller. Fix by not reusing that variable.
Spotted by Per Hallsmark <saxofon@musiker.nu>
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6661
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch creates a new driver, sierra.c, that supports the new
non-composite Sierra Wireless WWAN devices. The older Sierra
Wireless and Airprime devices are supported in airprime.c.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
coverity spotted (id #185) that we still use urb, if the allocation
fails in the error path. This patch fixes this by returning directly.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move variables only used on !__hppa__ into that #ifndef section. This
cleans up a compiler warning on parisc. Problem pointed out by
Joel Soete.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch limits the amount of outstanding 'write' data that can be
queued up for the ftdi_sio driver, to prevent userspace DoS attacks (or
simple accidents) that use up all the system memory by writing lots of
data to the serial port.
The original patch was by Guillaume Autran, who in turn based it on the
same mechanism implemented in the 'visor' driver. I (Ian Abbott)
re-targeted the patch to the latest sources, fixed a couple of errors,
renamed his new structure members, and updated the implementations of
the 'write_room' and 'chars_in_buffer' methods to take account of the
number of outstanding 'write' bytes. It seems to work fine, though at
low baud rates it is still possible to queue up an amount of data that
takes an age to shift (a job for another day!).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The anti user-DoS mechanism in the USB serial 'visor' driver can fail in
the following way:
visor_open: priv->outstanding_urbs = 0
visor_write: ++priv->outstanding_urbs
visor_close:
visor_open: priv->outstanding_urbs = 0
visor_write_bulk_callback: --priv->outstanding_urbs
So priv->outstanding_urbs ends up as (unsigned long)(-1). Not good!
I haven't seen this happen with the visor driver as I don't have the
hardware, but I have seen it while testing a patch to implement the same
functionality in the ftdi_sio driver (patch not yet submitted).
The fix is pretty simple: don't reinitialize outstanding_urbs in
visor_open. (Again, I haven't tested the fix in visor, but I have
tested it in ftdi_sio.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the kernel version to the usb-storage Protocol/SubClass
unneeded message in order to help us troubleshoot such problems.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases
for this that were in scsiglue.c. It also adds the flag to other devices
reported to need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as731) makes a couple of small fixes to the hub_port_resume
routine:
Don't return status >= 0 when an error occurs;
Clear the port-change-suspend status indicator after
resuming a device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as730) contains an unusual_devs entry for a Samsung MP3
device.
From: Ernis <ernisv@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as725) adds an unusual_devs entry for the Motorola RAZR V3x.
From: Davide Perini <perini.davide@dpsoftware.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
finish_device_resume() in the hub driver isn't careful always to return
a negative code in all the error pathways. It also doesn't return 0 in
all the success pathways. This patch (as724) fixes the behavior.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My recent patch converting usb-storage to use
usb_reset_composite_device() added a bug, a race between reset and
disconnect. It was necessary to drop the private lock while executing a
reset, and if a disconnect occurs at that time it will cause a crash.
This patch (as722) fixes the problem by explicitly checking for an early
termination after executing each command.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds
better debugging output &
an update of the quirk list
to the acm driver
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a new driver for the Cypress CY7C63xxx mirco controller series.
It currently supports the pre-programmed CYC63001A-PC by AK Modul-Bus
GmbH. It's based on a kernel 2.4 driver (cyport) by Marcus Maul which I
ported to kernel 2.6 using sysfs. I intend to support more controllers
of this family (and more features) as soon as I get hold of the required
IDs etc. Please see the source code's header for more information.
Signed-off-by: Oliver Bock <o.bock@fh-wolfenbuettel.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbfs stores the wrong signal number in the siginfo structure used for
notifying user programs about device disconnect. This patch (as726)
fixes it.
From: Zoran Marceta <Zoran.Marceta@micronasnit.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>