Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set the correct hwif->dma_base for the second channel in
ide_get_or_set_dma_base().
* Remove DMA enable code from cs5520_set_pio_mode(), this can
be handled by the generic ->dma_host_on method now.
* Add VDMA check to ide_config_drive_speed().
* drive->using_dma was never enabled since cs5520 host driver's
->ide_dma_on method overrided the generic ->ide_dma_on (so
__ide_dma_on() was never called, drive->using_dma was never set
and VDMA was never used since it depends on drive->using_dma).
Fix it by using ->dma_host_on method instead of ->ide_dma_on
(also add matching ->dma_host_off method).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out code reading taskfile registers from ide_end_drive_cmd()
to the new ide_tf_read() helper.
* Add IDE_TFLAG_IN_* taskfile flags to indicate the need to load
particular IDE taskfile register in ide_tf_read().
* Update ide_end_drive_cmd() to set respective IDE_TFLAG_IN_* taksfile flags.
* Add ide_get_lba_addr() for getting LBA sector address from taskfile struct.
* Factor out code getting sector address from ide_dump_ata_status()
to the new ide_dump_sector() function.
* Convert ide_dump_sector() to use ide_tf_read() and ide_get_lba_addr().
* Remove no longer needed ide_read_24().
The only change in functionality caused by this patch is that
ide_dump_ata_status() no longer prints "high"/"low" parts of LBA48
sector address (of course LBA48 sector address is still printed).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix registers loading order in ide_dump_ata_status()/ide_read_24().
Load registers in this order:
* IDE_SECTOR_REG
* IDE_LCYL_REG
* IDE_HCYL_REG
* IDE_SELECT_REG
It shouldn't affect anything (just a usual paranoia to separate changes
which change the way in which hardware is accessed from code cleanups).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove stale ide.h "configuration options":
* INITIAL_MULT_COUNT - always defined to 0
* SUPPORT_SLOW_DATA_PORTS - unused
* OK_TO_RESET_CONTROLLER - always defined to 1
* DISABLE_IRQ_NOSYNC - always defined to 0
Leave SUPPORT_VLB_SYNC (defined to 0 for CRIS and FRV, otherwise to 1)
for now but disallow overriding it by <asm/ide.h>.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't set write-only ide_task_t.hobRegister[6] and ide_task_t.hobRegister[7]
in idedisk_set_max_address_ext().
* Add struct ide_taskfile and use it in ide_task_t instead of tfRegister[]
and hobRegister[].
* Remove no longer needed IDE_CONTROL_OFFSET_HOB define.
* Add #ifndef/#endif __KERNEL__ around definitions of {task,hob}_struct_t.
While at it:
* Use ATA_LBA define for LBA bit (0x40) as suggested by Tejun Heo.
v2:
* Add missing newlines. (Noticed by Sergei)
* Use ~ATA_LBA instead of 0xBF. (Noticed by Sergei)
* Use unnamed unions for error/feature and status/command.
(Suggested by Sergei).
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove task_ioreg_t typedef from the kernel code (but leave it
in <linux/hdreg.h> for #ifndef/#endif __KERNEL__ case).
While at it also move sata_ioreg_t typedef under #ifndef/#endif __KERNEL__.
v2:
Remove name of the second parameter from ide_execute_command() declaration.
(Noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_xfer_verbose() fixups:
- beautify returned mode names
- fix PIO5 reporting
- make it return 'const char *'
* Change printk() level from KERN_DEBUG to KERN_INFO in ide_find_dma_mode().
* Add ide_id_dma_bug() helper based on ide_dma_verbose() to check for invalid
DMA info in identify block.
* Use ide_id_dma_bug() in ide_tune_dma() and ide_driveid_update().
As a result DMA won't be tuned or will be disabled after tuning if device
reports inconsistent info about enabled DMA mode (ide_dma_verbose() does the
same checks while the IDE device is probed by ide-{cd,disk} device driver).
* Remove no longer needed ide_dma_verbose().
This patch should fix the following problem with out-of-sync IDE messages
reported by Nick Warne:
hdd: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache<7>hdd:
skipping word 93 validity check
, UDMA(66)
and later debugged by Mark Lord to be caused by:
ide_dma_verbose()
printk( ... "2048kB Cache");
eighty_ninty_three()
printk(KERN_DEBUG "%s: skipping word 93 validity check\n");
ide_dma_verbose()
printk(", UDMA(66)"
Please note that as a result ide-{cd,disk} device drivers won't report the
DMA speed used but this is intended since now DMA mode being used is always
reported by IDE core code.
v2:
* fixes suggested by Randy:
- use KERN_CONT for printk()-s in ide-{cd,disk}.c
- don't remove argument name from ide_xfer_verbose() declaration
v3:
* Remove incorrect check for (id->field_valid & 1) from ide_id_dma_bug()
(spotted by Sergei).
* "XFER SLOW" -> "PIO SLOW" in ide_xfer_verbose() (suggested by Sergei).
* Fix ide_find_dma_mode() to report the correct mode ('mode' after being
limited by 'req_mode').
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Nick Warne <nick@ukfsn.org>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add more TSST (Toshiba/Samsung) drives to the
'broken cable detection' blacklist.
Signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix handling of the PIO modes for the pre-EIDE drives that did not support
the PIO Flow Control Transfer Mode value (00001 nnn) of the Set Transfer Mode
feature by skipping the actual mode programming.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_fix_driveid can now be unexported.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From the report by Nick Warne.
Tested-by: Nick Warne <nick@ukfsn.org>
Cc: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove dead code from ide_driveid_update().
While at it:
* Remove useless comment.
* s/HWIF(drive)/drive->hwif/
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
on BIOS for programming device/controller for DMA. Set it in cy82c693,
generic, ns87415, opti621 and trm290 host drivers.
* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520
host driver.
* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.
* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
implementations. Fix all places checking for presence of ->ide_dma_check
hook to check for ->ide_dma_on instead.
* Remove no longer needed code from config_drive_for_dma().
* Make ide_tune_dma() static.
v2:
* Fix config_drive_for_dma() return values.
* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
dummy config_drive_for_dma() inline.
* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().
* Fix init_hwif_it8213() comment.
There should be no functionality changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Devices which don't set word 93 validation bit should be now handled by
ide-iops.c::ivb_list[] and for debugging purposes cable detection can be
completely overriden with "idex=ata66" parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Need to probe slave device first to make it release PDIAG-
(this is required for correct device side cable detection).
Based on libata commit f31f0cc2f0.
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also ide-iops.c::__ide_wait_stat() could be static again.
Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:
* if PIO mode is set then ->dma_off_queitly is called to disable DMA
* if setting transfer mode fails ide_dump_status() is called to dump status
v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
depends on this fact, and calls "hdparm -p" without calling "hdparm -d".
Therefore to compensate for DMA being disabled by ide_config_drive_speed()
for PIO modes:
- add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver
- add handling of the new flag to ide-io.c::do_special()
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature().
While at it do following changes to match __ide_wait_stat() call in
ide_config_drive_speed():
* Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT.
* Check DRQ_STAT bit (shouldn't be set for good device status).
Also remove no longer needed wait_for_ready() from ide-iops.c.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off checking of the status register from ide_wait_stat() to
__ide_wait_stat() helper.
* Use the new helper in ide_config_drive_speed(). The only change in the
functionality is that the function now fails if after 20 sec (WAIT_CMD)
device is still busy (BUSY_STAT bit is set) while previously instead of
failing the function continued with checking for the correct device status
(which would give the device additional 10 usec to clear BUSY_STAT bit).
* Remove stale comment for ide_config_drive_speed().
* Remove duplicate comment for ide_wait_stat() from <linux/ide.h>.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This disk reports total number of sectors instead of maximum sector address
in response to READ_NATIVE_MAX_ADDRESS command and also happily accepts
SET_MAX_ADDRESS command with the bogus value. This results in +1 sector
capacity being used and errors on attempts to use the last sector.
...
hdd: Host Protected Area detected.
    current capacity is 78165360 sectors (40020 MB)
    native  capacity is 78165361 sectors (40020 MB)
hdd: Host Protected Area disabled.
...
hdd: reading: block=78165360, sectors=1, buffer=0xc1e63000
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=78165360, sector=78165360
...
Add hpa_list[] table and workaround the issue in idedisk_check_hpa().
v2:
* Add missing export and improve patch description a bit.
v3:
* Add list termination. (From Mikko)
Fixes kernel bugzilla bug #8816.
Thanks to Mikko for investigating the issue and helping with this patch.
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->OUTBSYNC instead of ->OUTB when writing command register
(needed for scc_pata and pmac host drivers).
* Don't check DRDY bit of the status register on ATAPI devices
(ATAPI devices are free to ignore DRDY bit).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_in_drive_list() from ide-dma.c to ide-iops.c.
* Add ivb_list[] table for listening early UDMA66 devices which don't conform
to ATA4 standard wrt cable detection (bit14 is zero, only bit13 is valid)
and use only device side cable detection for them since host side cable
detection may be unreliable.
* Add model "QUANTUM FIREBALLlct10 05" with firwmare "A03.0900" to the list
(from Craig's bugreport).
v2:
* Improve kernel message basing on suggestion from Sergei.
v3:
* Don't print kernel message when no device side cable detection is done,
plus some minor fixes. (Noticed by Sergei)
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter. Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.
Next patches add automatic detection of some systems using short cables.
Changes:
* Rename hwif->udma_four to hwif->cbl and make it u8.
* Convert all existing users accordingly (use ATA_CBL_* defines while at it).
* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().
* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tejun's recent eighty_ninty_three() fix has inspired me to do more thorough
review of the cable detection code...
* print user-friendly warning about limiting the maximum transfer speed
to UDMA33 (and the reason behind it) when 80-wire cable is not detected,
also while at it cleanup eighty_ninty_three() a bit
* use eighty_ninty_three() in ide_ata66_check(), this actually fixes 3 bugs:
- bit 14 (word 93 validity check) == 1 && bit 13 (80-wire cable test) == 1
were used as 80-wire cable present test for CONFIG_IDEDMA_IVB=n case
(please see FIXME comment in eighty_ninty_three() for more details)
- CONFIG_IDEDMA_IVB=y/n cases were interchanged
- check for SATA devices was missing
* remove private cable warnings from pdc_202xx{old,new} drivers now that core
code provides this functionality (plus, in pdc202xx_new case the test could
give false warnings for ATAPI devices because pdc202xx_new driver doesn't
even support ATAPI DMA)
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.
* add ide_hwif_t.udma_filter hook for filtering UDMA mask
(use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
(loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()
v2:
* rename ->filter_udma_mask to ->udma_filter
[ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
originated transfer mode change requests when 100MHz clock is used)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler).
A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.
To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
"ide: fix drive side 80c cable check, take 2" patch from Tejun Heo (commit
fab59375b9) fixed 80c bit test (bit13 of word93)
but we also need to fix master/slave IDENTIFY order (slave device should be
probed first in order to make it release PDIAG- signal) and we should also
check for pre-ATA3 slave devices (which may not release PDIAG- signal).
[ Unfortunately the fact that IDE driver doesn't reset devices itself helps
only a bit as it seems that some BIOS-es reset ATA devices after programming
the chipset, some BIOS-es can be set to not probe/configure selected devices,
there may be no BIOS in case of add-on cards etc. ]
Since we are quite late in the release cycle and the required changes will
affect a lot of systems just revert the fix for now.
[ Please also see libata commit f31f0cc2f0. ]
Thanks goes out to Fernando Mitio Yamada for reporting the problem
and patiently testing patches.
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
eighty_ninty_three() had word 93 validitity check but not the 80c bit
test itself (bit 13). This increases the chance of incorrect wire
detection especially because host side cable detection is often
unreliable and we sometimes soley depend on drive side cable
detection. Fix it.
[ bart: fix off-by-1 bit name in the patch description ]
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_host_on is called either when drive->using_dma == 1
or when return value is discarded make it void, also drop "ide_" prefix
* make __ide_dma_host_on() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_on() to atiixp_dma_host_on()
and sgiioc4_ide_dma_host_on() to sgiioc4_dma_host_on().
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Michal Miroslaw reported a problem (bugzilla #7023) where a user initiated
reset while the IDE layer was already resetting the channel caused a crash,
and provided a rough fix.
This is a slightly cleaner version of the fix which tracks the reset state
and blocks further reset requests while a reset is in progress.
Note this is not a security issue - random end users can't access the
ioctl in question anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When resuming from suspend-to-RAM, the NMI watchdog detects a lockup in
ide_wait_not_busy. Here's a screenshot of the trace taken by a digital
camera: http://www.uamt.feec.vutbr.cz/rizeni/pom/DSC03510-2.JPG
Let's touch the NMI watchdog in ide_wait_not_busy. The system then resumes
correctly from STR.
[akpm@osdl.org: modular build fix]
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is based on the proposed patches flying around but also checks that
the device in question is new enough to have word 93 rather thanb blindly
assuming word 93 == 0 means SATA (see ATA-5, ATA-7)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- pci/cy82c693.c: make a needlessly global function static
- remove the following unneeded EXPORT_SYMBOL's:
- ide-taskfile.c: do_rw_taskfile
- ide-iops.c: default_hwif_iops
- ide-iops.c: default_hwif_transport
- ide-iops.c: wait_for_ready
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
