Before sending out a TT_Request packet we must convert the tt_crc field value
to network order (since it is 16bits long).
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
ops_init should free the net_generic data on
init failure and __register_pernet_operations should not
call ops_free when NET_NS is not enabled.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_grow_window() has to grow rcv_ssthresh up to window_clamp, allowing
sender to increase its window.
tcp_grow_window() still assumes a tcp frame is under MSS, but its no
longer true with LRO/GRO.
This patch fixes one of the performance issue we noticed with GRO on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The broken check leads to rate control attempting to use HT40 while
the driver is configured for HT20. This leads to interesting hardware
issues.
HT40 can only be used if the channel type is either HT40- or HT40+
and if the channel type of the cell matches the local type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cooked monitor rx was recently changed to use ieee80211_add_rx_radiotap_header
instead of generating only limited radiotap information.
ieee80211_add_rx_radiotap_header assumes that FCS info is still present if
the hardware supports receiving it, however when cooked monitor rx packets
are processed, FCS info has already been stripped.
Fix this by adding an extra flag indicating FCS presence.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A parameter set exists for WRED mode, called wred_set, to hold the same
values for qavg and qidlestart across all VQs. The WRED mode values had
been previously held in the VQ for the default DP. After these values
were moved to wred_set, the VQ for the default DP was no longer created
automatically (so that it could be omitted on purpose, to have packets
in the default DP enqueued directly to the device without using RED).
However, gred_dump() was overlooked during that change; in WRED mode it
still reads qavg/qidlestart from the VQ for the default DP, which might
not even exist. As a result, this command sequence will cause an oops:
tc qdisc add dev $DEV handle $HANDLE parent $PARENT gred setup \
DPs 3 default 2 grio
tc qdisc change dev $DEV handle $HANDLE gred DP 0 prio 8 $RED_OPTIONS
tc qdisc change dev $DEV handle $HANDLE gred DP 1 prio 8 $RED_OPTIONS
This fixes gred_dump() in WRED mode to use the values held in wred_set.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make cgw_list static to remove the following sparse warning:
net/can/gw.c:69:1: warning: symbol 'cgw_list' was not declared.
Should it be static?
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add utility function to provide the average rssi per vif
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The background scan completion takes more time when the station is
having heavy uplink traffic. The scan state machine decides to fall
back to home channel on every off-channel visit when there are pending
frames in tx queue. bgscan completion took ~30sec on dual band US
regulatory card.
scan period = (20 active channels * probe timeout) +
(12 passive channels * passive probe timeout) +
(32 * timeout on home channel) +
(32 * flush timeout)
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When testing mesh synchronization we observed a global TSF slowdown that
was dependent on the number of synchronized mesh stations. This seems
to be caused by the TSF adjustment (read/write) latency.
Adding a small margin to the Toffset setpoint solved the problem.
Signed-off-by: Shinichi Hotori <hotorinn@gmail.com>
Signed-off-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 3a25a8c8 (mac80211: add improved HW queue control) introduced a
bug when running in AP mode without the IEEE80211_HW_QUEUE_CONTROL
flag set. The ieee80211_check_queues() function always returns
-EINVAL, preventing AP mode from starting. To fix this, check whether
this flag is set before checking if cab_queue is set properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My grand plan to allow drivers to gradually move over
to advertising virtual interface combinations and only
enforce with drivers that do want it enforced doesn't
seem to be working out, only Christian ever added the
advertising (to carl9170), nobody else did.
Begin enforcing combinations in cfg80211 so that users
can rely on the information reported about a device.
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a key is non persistent then it should not be used in future
connections but it should be kept for current connection. And it
should be removed when connecion is removed.
Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch changes the return type of function hci_persistent_key
from int to bool because it makes more sense to return information
whether a key is persistent or not as a bool.
Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/ethernet/atheros/atlx/atl1.c
drivers/net/ethernet/atheros/atlx/atl1.h
Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful to be able to monitor for FDB events in user space.
This patch adds support to generate netlink events when a change
is made to a device supporting the FDB ops.
This brings embedded switches inline with the SW net/bridge which
triggers events on FDB updates as well.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a generic dump routine drivers can call. It
should be sufficient to handle any bridging model that
uses the unicast address list. This should be most SR-IOV
enabled NICs.
v2: return error on nlmsg_put and use -EMSGSIZE instead
of -ENOMEM this is inline other usages
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a dev_uc_add_excl() and dev_mc_add_excl() calls
similar to the original dev_{uc|mc}_add() except it sets
the global bit and returns -EEXIST for duplicat entires.
This is useful for drivers that support SR-IOV, macvlan
devices and any other devices that need to manage the
unicast and multicast lists.
v2: fix typo UNICAST should be MULTICAST in dev_mc_add_excl()
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds two new flags NTF_MASTER and NTF_SELF that can
now be used to specify where PF_BRIDGE netlink commands should
be sent. NTF_MASTER sends the commands to the 'dev->master'
device for parsing. Typically this will be the linux net/bridge,
or open-vswitch devices. Also without any flags set the command
will be handled by the master device as well so that current user
space tools continue to work as expected.
The NTF_SELF flag will push the PF_BRIDGE commands to the
device. In the basic example below the commands are then parsed
and programmed in the embedded bridge.
Note if both NTF_SELF and NTF_MASTER bits are set then the
command will be sent to both 'dev->master' and 'dev' this allows
user space to easily keep the embedded bridge and software bridge
in sync.
There is a slight complication in the case with both flags set
when an error occurs. To resolve this the rtnl handler clears
the NTF_ flag in the netlink ack to indicate which sets completed
successfully. The add/del handlers will abort as soon as any
error occurs.
To support this new net device ops were added to call into
the device and the existing bridging code was refactored
to use these. There should be no required changes in user space
to support the current bridge behavior.
A basic setup with a SR-IOV enabled NIC looks like this,
veth0 veth2
| |
------------
| bridge0 | <---- software bridging
------------
/
/
ethx.y ethx
VF PF
\ \ <---- propagate FDB entries to HW
\ \
--------------------
| Embedded Bridge | <---- hardware offloaded switching
--------------------
In this case the embedded bridge must be managed to allow 'veth0'
to communicate with 'ethx.y' correctly. At present drivers managing
the embedded bridge either send frames onto the network which
then get dropped by the switch OR the embedded bridge will flood
these frames. With this patch we have a mechanism to manage the
embedded bridge correctly from user space. This example is specific
to SR-IOV but replacing the VF with another PF or dropping this
into the DSA framework generates similar management issues.
Examples session using the 'br'[1] tool to add, dump and then
delete a mac address with a new "embedded" option and enabled
ixgbe driver:
# br fdb add 22:35:19:ac:60:59 dev eth3
# br fdb
port mac addr flags
veth0 22:35:19:ac:60:58 static
veth0 9a:5f:81:f7:f6:ec local
eth3 00:1b:21:55:23:59 local
eth3 22:35:19:ac:60:59 static
veth0 22:35:19:ac:60:57 static
#br fdb add 22:35:19:ac:60:59 embedded dev eth3
#br fdb
port mac addr flags
veth0 22:35:19:ac:60:58 static
veth0 9a:5f:81:f7:f6:ec local
eth3 00:1b:21:55:23:59 local
eth3 22:35:19:ac:60:59 static
veth0 22:35:19:ac:60:57 static
eth3 22:35:19:ac:60:59 local embedded
#br fdb del 22:35:19:ac:60:59 embedded dev eth3
I added a couple lines to 'br' to set the flags correctly is all. It
is my opinion that the merit of this patch is now embedded and SW
bridges can both be modeled correctly in user space using very nearly
the same message passing.
[1] 'br' tool was published as an RFC here and will be renamed 'bridge'
http://patchwork.ozlabs.org/patch/117664/
Thanks to Jamal Hadi Salim, Stephen Hemminger and Ben Hutchings for
valuable feedback, suggestions, and review.
v2: fixed api descriptions and error case with both NTF_SELF and
NTF_MASTER set plus updated patch description.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending general queries was implemented as an optimisation to speed
up convergence on start-up. In order to prevent interference with
multicast routers a zero source address has to be used.
Unfortunately these packets appear to cause some multicast-aware
switches to misbehave, e.g., by disrupting multicast packets to us.
Since the multicast snooping feature still functions without sending
our own queries, this patch will change the default to not send
queries.
For those that need queries in order to speed up convergence on start-up,
a toggle is provided to restore the previous behaviour.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands when we discover that a real querier (one that queries
with a non-zero source address) we stop querying. However, even
after said querier has fallen off the edge of the earth, we will
never restart querying (unless the bridge itself is restarted).
This patch fixes this by kicking our own querier into gear when
the timer for other queriers expire.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the helper br_multicast_start_querier so that
the code which starts the queriers in br_multicast_toggle can
be reused elsewhere.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch errors of the following type:
* ERROR: "foo * bar" should be "foo *bar"
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_enter_quickack_mode() already calls tcp_incr_quickack() and sets
icsk->icsk_ack.ato to TCP_ATO_MIN. This patch removes the duplication.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must try harder to get unique (addr, port) pairs when
doing port autoselection for sockets with SO_REUSEADDR
option set.
We achieve this by adding a relaxation parameter to
inet_csk_bind_conflict. When 'relax' parameter is off
we return a conflict whenever the current searched
pair (addr, port) is not unique.
This tries to address the problems reported in patch:
8d238b25b1
Revert "tcp: bind() fix when many ports are bound"
Tests where ran for creating and binding(0) many sockets
on 100 IPs. The results are, on average:
* 60000 sockets, 600 ports / IP:
* 0.210 s, 620 (IP, port) duplicates without patch
* 0.219 s, no duplicates with patch
* 100000 sockets, 1000 ports / IP:
* 0.371 s, 1720 duplicates without patch
* 0.373 s, no duplicates with patch
* 200000 sockets, 2000 ports / IP:
* 0.766 s, 6900 duplicates without patch
* 0.768 s, no duplicates with patch
* 500000 sockets, 5000 ports / IP:
* 2.227 s, 41500 duplicates without patch
* 2.284 s, no duplicates with patch
Signed-off-by: Alex Copot <alex.mihai.c@gmail.com>
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two struct request_sock_ops providers, tcp and dccp.
inet_csk_reqsk_queue_prune() can avoid testing syn_ack_timeout being
NULL if we make it non NULL like syn_ack_timeout
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: dccp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates some comments to track RFC6298
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the per-cpu statistics kept for GRE, IPIP, and SIT tunnels
to use 64 bit statistics.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
its not used where, while we directly obtain ieee80211_bss's
pointer in ibss.c by calling cfg80211_get_bss
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removes hw.conf.channel usage from the following functions:
* ieee80211_mandatory_rates
* ieee80211_sta_get_rates
* ieee80211_frame_duration
* ieee80211_rts_duration
* ieee80211_ctstoself_duration
This is in preparation for multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a possible issue in the status count field management of the
ieee80211_tx_info data structure. In particular, when the AGGR
processing is employed,
status.rates[].count is set just for the first frame and not for
others belonging to the same burst, leading to wrong statistic data in
the mac80211 debug file system.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current channel is known, add frequency and channel type to
NL80211_CMD_GET_INTERFACE.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before we send probes in connection monitoring we check if scan is not
pending. But we do that check without locking. Fix that and also do not
start scan if connection monitoring is in progress.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
neigh_table_init_no_netlink() is only used in net/core/neighbour.c file.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most machines dont use UDP encapsulation (L2TP)
Adds a static_key so that udp_queue_rcv_skb() doesnt have to perform a
test if L2TP never setup the encap_rcv on a socket.
Idea of this patch came after Simon Horman proposal to add a hook on TCP
as well.
If static_key is not yet enabled, the fast path does a single JMP .
When static_key is enabled, JMP destination is patched to reach the real
encap_type/encap_rcv logic, possibly adding cache misses.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: dev@openvswitch.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Change get_tx_queues, drop unsused arg/return value real_tx_queues,
and use return by value (with error) rather than call by reference.
Probably bonding should just change to LLTX and the whole get_tx_queues
API could disappear!
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison operators were backwards in both garp_attr_lookup and
garp_attr_create, so the entire GID rbtree was in reverse order.
(There was no practical side effect to this though, except that PDUs
were sent with attributes listed in reverse order, which is still
valid by the protocol. This change is only for clarity.)
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
We discovered that PPPoATM has an excessively deep transmit queue. A
queue the size of the default socket send buffer (wmem_default) is
maintained between the PPP generic core and the ATM device.
Fix it to queue a maximum of *two* packets. The one the ATM device is
currently working on, and one more for the ATM driver to process
immediately in its TX done interrupt handler. The PPP core is designed
to feed packets to the channel with minimal latency, so that really
ought to be enough to keep the ATM device busy.
While we're at it, fix the fact that we were triggering the wakeup
tasklet on *every* pppoatm_pop() call. The comment saying "this is
inefficient, but doing it right is too hard" turns out to be overly
pessimistic... I think :)
On machines like the Traverse Geos, with a slow Geode CPU and two
high-speed ADSL2+ interfaces, there were reports of extremely high CPU
usage which could partly be attributed to the extra wakeups.
(The wakeup handling could actually be made a whole lot easier if we
stop checking sk->sk_sndbuf altogether. Given that we now only queue
*two* packets ever, one wonders what the point is. As it is, you could
already deadlock the thing by setting the sk_sndbuf to a value lower
than the MTU of the device, and it'd just block for ever.)
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ipv6 dst cache which copy from the dst generated by ICMPV6 RA packet.
this dst cache will not check expire because it has no RTF_EXPIRES flag.
So this dst cache will always be used until the dst gc run.
Change the struct dst_entry,add a union contains new pointer from and expires.
When rt6_info.rt6i_flags has no RTF_EXPIRES flag,the dst.expires has no use.
we can use this field to point to where the dst cache copy from.
The dst.from is only used in IPV6.
rt6_check_expired check if rt6_info.dst.from is expired.
ip6_rt_copy only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
ip6_dst_destroy release the ort.
Add some functions to operate the RTF_EXPIRES flag and expires(from) together.
and change the code to use these new adding functions.
Changes from v5:
modify ip6_route_add and ndisc_router_discovery to use new adding functions.
Only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set traffic class for CAIF packets, based on socket
priority, CAIF protocol type, or type of message.
Traffic class mapping for different packet types:
- control: TC_PRIO_CONTROL;
- flow control: TC_PRIO_CONTROL;
- at: TC_PRIO_CONTROL;
- rfm: TC_PRIO_INTERACTIVE_BULK;
- other sockets: equals to socket's TC;
- network data: no change.
Signed-off-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in the 'net' tree to get CAIF bug fixes upon which
the following set of CAIF feature patches depend.
Signed-off-by: David S. Miller <davem@davemloft.net>
Added kfree_skb() calls in the chnk_net.c file on
the error paths.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications using L2TP/IP sockets want to be able to bind() an L2TP/IP
socket to set the local tunnel id while leaving the auto-assigned source
address alone. So if no source address is supplied, don't overwrite
the address already stored in the socket.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The l2tp_ip socket close handler does not update the module refcount
correctly which prevents module unload after the first bind() call on
an L2TPv3 IP encapulation socket.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the point of this error-handling code, alloc_skb has succeded, so free
the resulting skb by jumping to the err label.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently an oops was reported in phonet if there was a failure during
network namespace creation.
[ 163.733755] ------------[ cut here ]------------
[ 163.734501] kernel BUG at include/net/netns/generic.h:45!
[ 163.734501] invalid opcode: 0000 [#1] PREEMPT SMP
[ 163.734501] CPU 2
[ 163.734501] Pid: 19145, comm: trinity Tainted: G W 3.4.0-rc1-next-20120405-sasha-dirty #57
[ 163.734501] RIP: 0010:[<ffffffff824d6062>] [<ffffffff824d6062>] phonet_pernet+0x182/0x1a0
[ 163.734501] RSP: 0018:ffff8800674d5ca8 EFLAGS: 00010246
[ 163.734501] RAX: 000000003fffffff RBX: 0000000000000000 RCX: ffff8800678c88d8
[ 163.734501] RDX: 00000000003f4000 RSI: ffff8800678c8910 RDI: 0000000000000282
[ 163.734501] RBP: ffff8800674d5cc8 R08: 0000000000000000 R09: 0000000000000000
[ 163.734501] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880068bec920
[ 163.734501] R13: ffffffff836b90c0 R14: 0000000000000000 R15: 0000000000000000
[ 163.734501] FS: 00007f055e8de700(0000) GS:ffff88007d000000(0000) knlGS:0000000000000000
[ 163.734501] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 163.734501] CR2: 00007f055e6bb518 CR3: 0000000070c16000 CR4: 00000000000406e0
[ 163.734501] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 163.734501] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 163.734501] Process trinity (pid: 19145, threadinfo ffff8800674d4000, task ffff8800678c8000)
[ 163.734501] Stack:
[ 163.734501] ffffffff824d5f00 ffffffff810e2ec1 ffff880067ae0000 00000000ffffffd4
[ 163.734501] ffff8800674d5cf8 ffffffff824d667a ffff880067ae0000 00000000ffffffd4
[ 163.734501] ffffffff836b90c0 0000000000000000 ffff8800674d5d18 ffffffff824d707d
[ 163.734501] Call Trace:
[ 163.734501] [<ffffffff824d5f00>] ? phonet_pernet+0x20/0x1a0
[ 163.734501] [<ffffffff810e2ec1>] ? get_parent_ip+0x11/0x50
[ 163.734501] [<ffffffff824d667a>] phonet_device_destroy+0x1a/0x100
[ 163.734501] [<ffffffff824d707d>] phonet_device_notify+0x3d/0x50
[ 163.734501] [<ffffffff810dd96e>] notifier_call_chain+0xee/0x130
[ 163.734501] [<ffffffff810dd9d1>] raw_notifier_call_chain+0x11/0x20
[ 163.734501] [<ffffffff821cce12>] call_netdevice_notifiers+0x52/0x60
[ 163.734501] [<ffffffff821cd235>] rollback_registered_many+0x185/0x270
[ 163.734501] [<ffffffff821cd334>] unregister_netdevice_many+0x14/0x60
[ 163.734501] [<ffffffff823123e3>] ipip_exit_net+0x1b3/0x1d0
[ 163.734501] [<ffffffff82312230>] ? ipip_rcv+0x420/0x420
[ 163.734501] [<ffffffff821c8515>] ops_exit_list+0x35/0x70
[ 163.734501] [<ffffffff821c911b>] setup_net+0xab/0xe0
[ 163.734501] [<ffffffff821c9416>] copy_net_ns+0x76/0x100
[ 163.734501] [<ffffffff810dc92b>] create_new_namespaces+0xfb/0x190
[ 163.734501] [<ffffffff810dca21>] unshare_nsproxy_namespaces+0x61/0x80
[ 163.734501] [<ffffffff810afd1f>] sys_unshare+0xff/0x290
[ 163.734501] [<ffffffff8187622e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 163.734501] [<ffffffff82665539>] system_call_fastpath+0x16/0x1b
[ 163.734501] Code: e0 c3 fe 66 0f 1f 44 00 00 48 c7 c2 40 60 4d 82 be 01 00 00 00 48 c7 c7 80 d1 23 83 e8 48 2a c4 fe e8 73 06 c8 fe 48 85 db 75 0e <0f> 0b 0f 1f 40 00 eb fe 66 0f 1f 44 00 00 48 83 c4 10 48 89 d8
[ 163.734501] RIP [<ffffffff824d6062>] phonet_pernet+0x182/0x1a0
[ 163.734501] RSP <ffff8800674d5ca8>
[ 163.861289] ---[ end trace fb5615826c548066 ]---
After investigation it turns out there were two issues.
1) Phonet was not implementing network devices but was using register_pernet_device
instead of register_pernet_subsys.
This was allowing there to be cases when phonenet was not initialized and
the phonet net_generic was not set for a network namespace when network
device events were being reported on the netdevice_notifier for a network
namespace leading to the oops above.
2) phonet_exit_net was implementing a confusing and special case of handling all
network devices from going away that it was hard to see was correct, and would
only occur when the phonet module was removed.
Now that unregister_netdevice_notifier has been modified to synthesize unregistration
events for the network devices that are extant when called this confusing special
case in phonet_exit_net is no longer needed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already synthesize events in register_netdevice_notifier and synthesizing
events in unregister_netdevice_notifier allows to us remove the need for
special case cleanup code.
This change should be safe as it adds no new cases for existing callers
of unregiser_netdevice_notifier to handle.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added strict checking of PadN, as PadN can be used to increase header
size and thus push the protocol header into the 2nd fragment.
PadN is used to align the options within the Hop-by-Hop or
Destination Options header to 64-bit boundaries. The maximum valid
size is thus 7 bytes.
RFC 4942 recommends to actively check the "payload" itself and
ensure that it contains only zeroes.
See also RFC 4942 section 2.1.9.5.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix bluetooth userland regression reported by Keith Packard, from
Gustavo Padovan.
2) Revert ath9k PS idle change, from Sujith Manoharan.
3) Correct default TCP memory limits (again), from Eric Dumazet.
4) Fix tcp_rcv_rtt_update() accidental use of unscaled RTT, from Neal
Cardwell.
5) We made a facility for layers like wireless to say how much tailroom
they need in the SKB for link layer stuff such as wireless
encryption etc., but TCP works hard to fill every SKB out to the end
defeating this specification.
This leads to every TCP packet getting reallocated by the wireless
code in order to have the right amount of tailroom available.
Fix TCP to only fill SKBs out to the real amount of data area it
asked for during the allocation, this way it won't eat into the
slack added for the device's tailroom needs.
Reported by Marc Merlin and fixed by Eric Dumazet.
6) Leaks, endian bugs, and new device IDs in bluetooth from Santosh
Nayak, João Paulo Rechi Vita, Cho, Yu-Chen, Andrei Emeltchenko,
AceLan Kao, and Andrei Emeltchenko.
7) OOPS on tty_close fix in bluetooth's hci_ldisc from Johan Hovold.
8) netfilter erroneously scales TCP window twice, fix from Changli Gao.
9) Memleak fix in wext-core from Julia Lawall.
10) Consistently handle invalid TCP packets in ipv4 vs. ipv6 conntrack,
from Jozsef Kadlecsik.
11) Validate IP header length properly in netfilter conntrack's
ipv4_get_l4proto().
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
NFC: Fix the LLCP Tx fragmentation loop
rtlwifi: Add missing DMA buffer unmapping for PCI drivers
rtlwifi: Preallocate USB read buffers and eliminate kalloc in read routine
tcp: avoid order-1 allocations on wifi and tx path
net: allow pskb_expand_head() to get maximum tailroom
bridge: Do not send queries on multicast group leaves
MAINTAINERS: Mark NATSEMI driver as orphan'd.
tcp: fix tcp_rcv_rtt_update() use of an unscaled RTT sample
tcp: restore correct limit
Revert "ath9k: fix going to full-sleep on PS idle"
rt2x00: Fix rfkill_polling register function.
bcma: fix build error on MIPS; implicit pcibios_enable_device
netfilter: nf_conntrack: fix incorrect logic in nf_conntrack_init_net
netfilter: nf_ct_ipv4: packets with wrong ihl are invalid
netfilter: nf_ct_ipv4: handle invalid IPv4 and IPv6 packets consistently
net/wireless/wext-core.c: add missing kfree
rtlwifi: Fix oops on rate-control failure
mac80211: Convert WARN_ON to WARN_ON_ONCE
rtlwifi: rtl8192de: Fix firmware initialization
nl80211: ensure interface is up in various APIs
...
Fixed coding style issues in net/core/utils.c
in relation with braces placement.
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
extern int sysctl_mld_max_msf is already defined in linux/ipv6.h.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed net/core/net-sysfs.c: netdev_store() to use kstrtoul()
instead of obsolete simple_strtoul().
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As specified in RFC6106, DNSSL option contains one or more domain names
of DNS suffixes. 8-bit identifier of the DNSSL option type as assigned
by the IANA is 31. This option should also be treated as userland.
Signed-off-by: Alexey I. Froloff <raorn@raorn.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were sending the LTO TLV as a version TLV instead of the actual link
timeout one.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dsap and ssap were swapped when sending DN or DISC.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if logic could lead to zero length TLVs.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
recv_n is set properly when receiving an HDLC frame.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some HW/drivers get notifications when a tag moves out of the radio field.
This notification is now forwarded to user space through netlink.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The target index can be used by userspace to uniquely identify a target
and thus should be kept unique, per NFC adapter. Moreover, some protocols
do not provide a logical index when discovering new targets, so we have to
generate one for them.
For NCI or pn533 to fetch their logical index, we added a logical_idx field
to the target structure.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most NFC HCI chipsets actually use a simplified HDLC link layer to
carry HCI payloads.
This implementation registers itself as an HCI device on behalf of the
NFC driver.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an implementation of ETSI TS 102 622 specification.
Many NFC chipsets use HCI as the host <-> target protocol on top of a
serial link like i2c.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NFC drivers will call this routine when they detect that a tag leaves the
RF field. This will eventually lead to the corresponding netlink event
to be sent.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some chips are capable of detecting when a tag is out of the field, so
they could send a netlink event about it to userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Record the RANN sender's address only for RANNs that meet the acceptance
criteria (per sections 13.10.12.4.2).
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware may decide to switch channels while already beaconing, e.g.
in response to a cfg80211 connect request on a different vif. Add this
event to notify userspace when an AP or GO interface has successfully
migrated to a new channel, so it can update its configuration
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.
Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad's comment prompted me to look closer at
the error paths in ieee80211_do_open() and I
found one that should use the error labels.
Also add a comment about the clear_bit since
in many error cases the bit hasn't been set.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.
To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.
Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.
So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP netdev is really only active when beaconing, so
manage the carrier state accordingly. Also do that for
VLAN interfaces enslaved to a given AP interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Section 13.2.3 of IEEE 80211s standard requires BSSBasicRateSet of mesh nodes
to be identical to establish peer link.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basic rates are added with supported rates IE and extended supported
rates IE.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.
After investigation, it turns out TCP uses sk_stream_alloc_skb() and
used as a convention skb_tailroom(skb) to know how many bytes of data
payload could be put in this skb (for non SG capable devices)
Note : these skb used kmalloc-4096 (MTU=1500 + MAX_HEADER +
sizeof(struct skb_shared_info) being above 2048)
Later, mac80211 layer need to add some bytes at the tail of skb
(IEEE80211_ENCRYPT_TAILROOM = 18 bytes) and since no more tailroom is
available has to call pskb_expand_head() and request order-1
allocations.
This patch changes sk_stream_alloc_skb() so that only
sk->sk_prot->max_header bytes of headroom are reserved, and use a new
skb field, avail_size to hold the data payload limit.
This way, order-0 allocations done by TCP stack can leave more than 2 KB
of tailroom and no more allocation is performed in mac80211 layer (or
any layer needing some tailroom)
avail_size is unioned with mark/dropcount, since mark will be set later
in IP stack for output packets. Therefore, skb size is unchanged.
Reported-by: Marc MERLIN <marc@merlins.org>
Tested-by: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.
Turns out part of the problem comes from pskb_expand_head() not using
ksize() to get exact head size given by kmalloc(). Doing the same thing
than __alloc_skb() allows more tailroom in skb and can prevent future
reallocations.
As a bonus, struct skb_shared_info becomes cache line aligned.
Reported-by: Marc MERLIN <marc@merlins.org>
Tested-by: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands the bridge IGMP snooping system will respond to
group leave messages with queries for remaining membership.
This is both unnecessary and undesirable. First of all any
multicast routers present should be doing this rather than us.
What's more the queries that we send may end up upsetting other
multicast snooping swithces in the system that are buggy.
In fact, we can simply remove the code that send these queries
because the existing membership expiry mechanism doesn't rely
on them anyway.
So this patch simply removes all code associated with group
queries in response to group leave messages.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The define CONFIG_BATMAN_ADV_BLA switches the bridge loop avoidance
on - skip it, and the bridge loop avoidance is not compiled in.
This is useful if binary size should be saved or the feature is
not needed.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
backbone gateways may be part of the same LAN, but participate
in different meshes. With this patch, backbone gateways form groups by
applying the groupid of another backbone gateway if it is higher. After
forming the group, they only accept messages from backbone gateways of
the same group.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When multiple backbone gateways relay the same broadcast from the
backbone into the mesh, other nodes in the mesh may receive this
broadcast multiple times. To avoid this, the crc checksums of
received broadcasts are recorded and new broadcast packets with
the same content may be dropped if received by another gateway.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
As the backbone gateways are connected to the same backbone, they
should announce the same clients on the backbone non-exclusively.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
as backbone gateways will all independently announce the same clients,
also the tt global table must be able to hold multiple originators per
client entry.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This second version of the bridge loop avoidance for batman-adv
avoids loops between the mesh and a backbone (usually a LAN).
By connecting multiple batman-adv mesh nodes to the same ethernet
segment a loop can be created when the soft-interface is bridged
into that ethernet segment. A simple visualization of the loop
involving the most common case - a LAN as ethernet segment:
node1 <-- LAN --> node2
| |
wifi <-- mesh --> wifi
Packets from the LAN (e.g. ARP broadcasts) will circle forever from
node1 or node2 over the mesh back into the LAN.
With this patch, batman recognizes backbone gateways, nodes which are
part of the mesh and backbone/LAN at the same time. Each backbone
gateway "claims" clients from within the mesh to handle them
exclusively. By restricting that only responsible backbone gateways
may handle their claimed clients traffic, loops are effectively
avoided.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The functionality is to be replaced by an improved implementation,
so first clean up.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
bitarray.c consists mostly of functionality that is already available as part
of the standard kernel API. batman-adv could use architecture optimized code
and reduce the binary size by switching to the standard functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In packet.h the numeric constant 6 is used instead of the more portable ETH_ALEN
define. This patch substitute any hardcoded value with such define.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F3IR
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
* tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
netdma: adding alignment check for NETDMA ops
ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata
ioat: ring size variables need to be 32bit to avoid overflow
iop-adma: Corrected array overflow in RAID6 Xscale(R) test.
ioat: fix size of 'completion' for Xen
Report Toffset to userspace.
Let userspace select the mesh synchronization method.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds MBSS extensible synchronization framework (Sec.
13.13.2 of IEEE Std. 802.11-2012).
The framework is implemented via an ops table which defines the
following functions:
rx_bcn_presp() - this is called every time a mesh beacon is
received.
adjust_tbtt() - this is called immediately before a beacon is about
to be transmitted.
The default neighbor offset synchronization defined in the standard is
implemented. We also provide template functions for vendor specific
methods.
When neighbor offset synchronization is active (which is the default)
mesh neighbors in the same MBSS will track timing offsets to each other
and compensate clock drift.
In our tests we observed that this mesh synchronization implementation
successfully corrected drifts between stations of ~2PPM while
introducing a jitter of ~20us.
It is also possible to test this framework on mac80211_hwsim simulated
phys to see how it behaves under different topologies, over poor links,
etc.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reading and writing back the tsf value via tsf is too slow if one wants
to make small increments to this timer. With this change you can use
the syntax "+=<some value>" or "-=<some value>" to add or substract a
value from the tsf counter.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While associated we should never have empty SSID, but life can be full
of surprises, and is allways better to print a warning than crash.
Before memcpy() in ieee80211_probereq_get() check ssid_len instead of
ssid pointer, sice pointer it always passed by "ssidie + 2" expression
to send probe functions, so practically never can be NULL.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding pending SKBs there's no need to
stop all queues, we only need to stop those
that we're adding frames to. Implement that
by lazily stopping a queue as we add an SKB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queue status changes we need to do a fair
bit of work, so ignore no-op changes early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.
Also fix up the restart code to not try to set up
the queues in this case.
Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.
Also verify that the AC number given is valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.
Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently stop the queue when changing the rate
control between 20/40 MHz in the BSS. This seems to
have been necessary when we actually changed the
channel, but now that we just update the station it
doesn't seem right any more. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel type argument to the rate_update()
callback isn't really the correct way to give
the rate control algorithm about the desired
RX bandwidth of the peer.
Remove this argument, and instead update the
STA capabilities with 20/40 appropriately. The
SMPS update done by this callback works in the
same way, so this makes the callback cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing the channel type during operation is
confusing to some drivers and will be hard to
handle in multi-channel scenarios. Instead of
changing the channel, set it to the right HT
channel before authenticating/associating and
don't change it -- just update the 20/40 MHz
restrictions in rate control as needed when
changed by the AP.
This also fixes a problem that Paul missed in
his fix for the "regulatory makes us deaf"
issue -- when we couldn't use 40 MHz we still
associated saying we were using 40 MHz, which
could in similarly broken APs make us never
even connect successfully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the AC constants instead of hard-coding
the numbers with comments.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a trivial wrapper function, inline it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no reason for it to not be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the code formatting and also replace
the constant 0 by IEEE80211_AC_VO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bad indentation & pointless if nesting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.
Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.
Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.
The intent in the code was to only use the 'm' measurement if it was a
new minimum. However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.
The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c43b874d5d (tcp: properly initialize tcp memory limits) tried
to fix a regression added in commits 4acb4190 & 3dc43e3,
but still get it wrong.
Result is machines with low amount of memory have too small tcp_rmem[2]
value and slow tcp receives : Per socket limit being 1/1024 of memory
instead of 1/128 in old kernels, so rcv window is capped to small
values.
Fix this to match comment and previous behavior.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in function nf_conntrack_init_net,when nf_conntrack_timeout_init falied,
we should call nf_conntrack_ecache_fini to do rollback.
but the current code calls nf_conntrack_timeout_fini.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It was reported that the Linux kernel sometimes logs:
klogd: [2629147.402413] kernel BUG at net / netfilter /
nf_conntrack_proto_tcp.c: 447!
klogd: [1072212.887368] kernel BUG at net / netfilter /
nf_conntrack_proto_tcp.c: 392
ipv4_get_l4proto() in nf_conntrack_l3proto_ipv4.c and tcp_error() in
nf_conntrack_proto_tcp.c should catch malformed packets, so the errors
at the indicated lines - TCP options parsing - should not happen.
However, tcp_error() relies on the "dataoff" offset to the TCP header,
calculated by ipv4_get_l4proto(). But ipv4_get_l4proto() does not check
bogus ihl values in IPv4 packets, which then can slip through tcp_error()
and get caught at the TCP options parsing routines.
The patch fixes ipv4_get_l4proto() by invalidating packets with bogus
ihl value.
The patch closes netfilter bugzilla id 771.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
IPv6 conntrack marked invalid packets as INVALID and let the user
drop those by an explicit rule, while IPv4 conntrack dropped such
packets itself.
IPv4 conntrack is changed so that it marks INVALID packets and let
the user to drop them.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch is intended to solve the follwing issues in RANN propagation:
[1] The interval in propagated RANN should be based on the interval of received RANN.
[2] The aggregated path metric for propagated RANN is as received plus own link metric
towards the transmitting mesh STA (not root mesh STA).
[3] The comparison of path metric for RANN with same sequence number should be done
before deciding whether to propagate or not.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HWMP sequence number of received RANN element is compared to decide whether to be
propagated. The sequence number is required to covert from 32bit little endian data into
CPUs endianness for comparison. The same applies to the RANN metric.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving DTIM we currently disable power save mode in the
hardware unconditionally, i.e. also when the hardware was not sleeping.
This causes trouble with at least one wireless chipset (Ralink RT3572).
When the hardware is not sleeping and we send a wakeup command (e.g.
this happens after a scan) then a significant decrease of the link
quality or a disconnect may occur.
Disabling power save mode only when it was enabled prevents this issue.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling mod_timer from the rx/tx hotpath is somewhat expensive, and the
timeout doesn't need to be so precise.
Switch to a different strategy: Schedule the timer initially, store jiffies
of all last rx/tx activity which would previously modify the timer, and
let the timer re-arm itself after checking the last rx/tx timestamp.
Make the session timers deferrable to avoid causing extra wakeups on systems
running on battery.
This visibly reduces CPU load under high network load on small embedded
systems.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets the user know which interface has failed
the check_sdata_in_driver check.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since some of the HT code pre-dates 802.11n-2009
some names are wrong. The one that bothers me most
is that "HT operation" is called "HT information"
in our code and that causes confusion.
Rename "HT information" to "HT operation" and also
the control_chan field to primary_chan to match
the name used in the spec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the probe frame (nullfunc) is stuck at the hw queue. so that
the mac80211 terminates the connection as it wont see the tx status.
Instead of waiting for long period for ack status, lets call flush
to get nullfunc status immediately. It also helps to send the nullfunc
till max tries reached.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There might be latency at AP side to update TIM IE which could cause the
station to send pspoll frame even after the wakeup. If the powersave is
disabled, the nullfunc notification alone is sufficient to receive
frames from the AP. And if the pspoll frame was already sent, no need to
resend the frame till it was acked by AP.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free extra as done in the error-handling code just above.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 handling code should ensure as much as
it can that the interface is in a valid state, it
can certainly ensure the interface is running.
Not doing so can cause calls through mac80211 into
the driver that result in warnings and unspecified
behaviour in the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TU_TO_EXP_TIME() macro already includes the
"jiffies +" piece of the calculation, so don't
add jiffies again.
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We may hit this in xt_LOG:
net/built-in.o:xt_LOG.c:function dump_ipv6_packet:
error: undefined reference to 'ip6t_ext_hdr'
happens with these config options:
CONFIG_NETFILTER_XT_TARGET_LOG=y
CONFIG_IP6_NF_IPTABLES=m
ip6t_ext_hdr is fairly small and it is called in the packet path.
Make it static inline.
Reported-by: Simon Kirby <sim@netnation.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For a picked up connection, the window win is scaled twice: one is by the
initialization code, and the other is by the sender updating code.
I use the temporary variable swin instead of modifying the variable win.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
1) Fix inaccuracies in network driver interface documentation, from Ben
Hutchings.
2) Fix handling of negative offsets in BPF JITs, from Jan Seiffert.
3) Compile warning, locking, and refcounting fixes in netfilter's
xt_CT, from Pablo Neira Ayuso.
4) phonet sendmsg needs to validate user length just like any other
datagram protocol, fix from Sasha Levin.
5) Ipv6 multicast code uses wrong loop index, from RongQing Li.
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
As soon as an skb is queued into socket error queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as an skb is queued into socket receive_queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2f53384424 (tcp: allow splice() to build full TSO packets) added
a regression for splice() calls using SPLICE_F_MORE.
We need to call tcp_flush() at the end of the last page processed in
tcp_sendpages(), or else transmits can be deferred and future sends
stall.
Add a new internal flag, MSG_SENDPAGE_NOTLAST, acting like MSG_MORE, but
with different semantic.
For all sendpage() providers, its a transparent change. Only
sock_sendpage() and tcp_sendpages() can differentiate the two different
flags provided by pipe_to_sendpage()
Reported-by: Tom Herbert <therbert@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail>com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
This is the fallout from adding memcpy alignment workaround for certain
IOATDMA hardware. NetDMA will only use DMA engine that can handle byte align
ops.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The conditional which decides to skip inactive filters does not
change with the change of loop index, so it is unnecessary to
check them many times.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3e4d3af501 (mm: stack based kmap_atomic()) we dont have
to disable BH anymore while mapping skb frags.
We can remove kmap_skb_frag() / kunmap_skb_frag() helpers and use
kmap_atomic() / kunmap_atomic()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although not specified in 8021Qaz spec, it could be useful to enable drivers
whose HW supports setting a rate limit for an ETS TC. This patch adds this
optional attribute to DCB netlink. To use it, drivers should implement and
register the callbacks ieee_setmaxrate and ieee_getmaxrate. The units are 64
bits long and specified in Kbps to enable usage over both slow and very fast
networks.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to export this to enable drivers use rt_tos2priority()
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert array index from the loop bound to the loop index.
And remove the void type conversion to ip6_mc_del1_src() return
code, seem it is unnecessary, since ip6_mc_del1_src() does not
use __must_check similar attribute, no compiler will report the
warning when it is removed.
v2: enrich the commit header
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
getsockopt(..., SCTP_EVENTS, ...) performs a length check and returns
an error if the user provides less bytes than the size of struct
sctp_event_subscribe.
Struct sctp_event_subscribe needs to be extended by an u8 for every
new event or notification type that is added.
This obviously makes getsockopt fail for binaries that are compiled
against an older versions of <net/sctp/user.h> which do not contain
all event types.
This patch changes getsockopt behaviour to no longer return an error
if not enough bytes are being provided by the user. Instead, it
returns as much of sctp_event_subscribe as fits into the provided buffer.
This leads to the new behavior that users see what they have been aware
of at compile time.
The setsockopt(..., SCTP_EVENTS, ...) API is already behaving like this.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, most drivers do not support transmit SO_TIMESTAMPING. For those
that do support it, there is one appropriate response to the get_ts_info
query. This patch adds a common function providing this response.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a new ethtool ioctl that exposes the SO_TIMESTAMPING
capabilities of a network interface. In addition, user space programs
can use this ioctl to discover the PTP Hardware Clock (PHC) device
associated with the interface.
Since software receive time stamps are handled by the stack, the generic
ethtool code can answer the query correctly in case the MAC or PHY
drivers lack special time stamping features.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 72331bc [ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be
consistent with ipv4] the code of 'inet6_rtm_getroute()' was re-ordered
such that the reference to 'rt->dst' is incremented prior skb
allocation.
Hence, if 'alloc_skb()' fails, must drop a reference from 'rt->dst'.
Add the missing 'dst_release()' call.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to decrement the conntrack counter if we fail to access the
zone extension.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error path misses putting the timeout object. This patch adds
new function xt_ct_tg_timeout_put() to put the timeout object.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XOR instruction fo BPF machine. Needed for computing packet hashes.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, BPF filters are bind to sockets. Since BPF machine becomes handy
for other purposes, this patch allows to create unattached filter.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is renamed to make it a little more clear what it does.
It is not added to any .h because it is not for general consumption, only for
bpf internal use (and so by the jits).
Signed-of-by: Jan Seiffert <kaffeemonster@googlemail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmsplice()/splice(pipe, socket) call do_tcp_sendpages() one page at a
time, adding at most 4096 bytes to an skb. (assuming PAGE_SIZE=4096)
The call to tcp_push() at the end of do_tcp_sendpages() forces an
immediate xmit when pipe is not already filled, and tso_fragment() try
to split these skb to MSS multiples.
4096 bytes are usually split in a skb with 2 MSS, and a remaining
sub-mss skb (assuming MTU=1500)
This makes slow start suboptimal because many small frames are sent to
qdisc/driver layers instead of big ones (constrained by cwnd and packets
in flight of course)
In fact, applications using sendmsg() (adding an additional memory copy)
instead of vmsplice()/splice()/sendfile() are a bit faster because of
this anomaly, especially if serving small files in environments with
large initial [c]wnd.
Call tcp_push() only if MSG_MORE is not set in the flags parameter.
This bit is automatically provided by splice() internals but for the
last page, or on all pages if user specified SPLICE_F_MORE splice()
flag.
In some workloads, this can reduce number of sent logical packets by an
order of magnitude, making zero-copy TCP actually faster than
one-copy :)
Reported-by: Tom Herbert <therbert@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail>com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f04565ddf5 (dev: use name hash for dev_seq_ops) added a second
regression, as some devices are missing from /proc/net/dev if many
devices are defined.
When seq_file buffer is filled, the last ->next/show() method is
canceled (pos value is reverted to value prior ->next() call)
Problem is after above commit, we dont restart the lookup at right
position in ->start() method.
Fix this by removing the internal 'pos' pointer added in commit, since
we need to use the 'loff_t *pos' provided by seq_file layer.
This also reverts commit 5cac98dd0 (net: Fix corruption
in /proc/*/net/dev_mcast), since its not needed anymore.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Mihai Maruseac <mmaruseac@ixiacom.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unix_dgram_sendmsg() currently builds linear skbs, and this can stress
page allocator with high order page allocations. When memory gets
fragmented, this can eventually fail.
We can try to use order-2 allocations for skb head (SKB_MAX_ALLOC) plus
up to 16 page fragments to lower pressure on buddy allocator.
This patch has no effect on messages of less than 16064 bytes.
(on 64bit arches with PAGE_SIZE=4096)
For bigger messages (from 16065 to 81600 bytes), this patch brings
reliability at the expense of performance penalty because of extra pages
allocations.
netperf -t DG_STREAM -T 0,2 -- -m 16064 -s 200000
->4086040 Messages / 10s
netperf -t DG_STREAM -T 0,2 -- -m 16068 -s 200000
->3901747 Messages / 10s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NF_CONNTRACK_TIMEOUT=n we have following warning :
CC [M] net/netfilter/xt_CT.o
net/netfilter/xt_CT.c: In function ‘xt_ct_tg_check_v1’:
net/netfilter/xt_CT.c:284: warning: label ‘err4’ defined but not used
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
The standard ways of probing a device's promiscuity
(ifi_flags, for instance) does not report the actual
state of the device. This patch adds dev->promiscuity
to the netlink netdevice report so that users can know
for certain if the device is acting PROMISC or not.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/addrconf.c:340: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
net/ipv6/addrconf.c:342: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:444: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:1337: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
net/ipv6/addrconf.c:1526: ERROR: "(foo*)" should be "(foo *)"
net/ipv6/addrconf.c:1671: ERROR: open brace '{' following function declarations go on the next line
net/ipv6/addrconf.c:1914: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2368: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2370: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2416: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2437: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:2573: ERROR: "foo * bar" should be "foo *bar"
net/ipv6/addrconf.c:3797: ERROR: "foo* bar" should be "foo *bar"
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp.c:501: ERROR: "(foo*)" should be "(foo *)"
icmp.c:582: ERROR: "(foo*)" should be "(foo *)"
icmp.c:954: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_rules.c:26: ERROR: open brace '{' following struct go on the same line
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
exthdrs_core.c:113: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs_core.c:114: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
exthdrs.c:726: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs.c:741: ERROR: "(foo*)" should be "(foo *)"
exthdrs.c:741: ERROR: "(foo*)" should be "(foo *)"
exthdrs.c:744: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:746: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:748: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:750: ERROR: "(foo**)" should be "(foo **)"
exthdrs.c:755: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
exthdrs.c:896: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
datagram.c:101: ERROR: "(foo*)" should be "(foo *)"
datagram.c:521: ERROR: space required before the open parenthesis '('
datagram.c:830: WARNING: braces {} are not necessary for single statement blocks
datagram.c:849: WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_core.c:13: ERROR: space required before the open parenthesis '('
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sit.c:118: ERROR: "foo * bar" should be "foo *bar"
sit.c:694: ERROR: "(foo*)" should be "(foo *)"
sit.c:724: ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Simon Horman <horms@verge.net.au>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
In IPv4, if an RTA_IIF attribute is specified within an RTM_GETROUTE
message, then a route is searched as if a packet was received on the
specified 'iif' interface.
However in IPv6, RTA_IIF is not interpreted in the same way:
'inet6_rtm_getroute()' always calls 'ip6_route_output()', regardless the
RTA_IIF attribute.
As a result, in IPv6 there's no way to use RTM_GETROUTE in order to look
for a route as if a packet was received on a specific interface.
Fix 'inet6_rtm_getroute()' so that RTA_IIF is interpreted as "lookup a
route as if a packet was received on the specified interface", similar
to IPv4's 'inet_rtm_getroute()' interpretation.
Reported-by: Ami Koren <amikoren@yahoo.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no known problem here, but this is one of only two non-arch files
in the kernel which use asm/atomic.h instead of linux/atomic.h.
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If both addresses equal, nothing needs to be done. If the device is down,
then we simply copy the new address to dev->dev_addr. If the device is up,
then we add another loopback device with the new address, and if that does
not fail, we remove the loopback device with the old address. And only
then, we update the dev->dev_addr.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An infinite loop occurred if garp_attr_create was called with the values
of an existing attribute. This might happen if a previous leave request
for the attribute has not yet been followed by a PDU transmission (or,
if the application previously issued a join request for the attribute
and is now issuing another one, without having issued a leave request).
If garp_attr_create finds an existing attribute having the same values,
return the address to it. Its state will then get updated (i.e., if it
was in a leaving state, it will move into a non-leaving state and not
get deleted during the next PDU transmission).
To accomplish this fix, collapse garp_attr_insert into garp_attr_create
(which is its only caller).
Thanks to Jorge Boncompte [DTI2] <jorge@dti2.net> for contributing to
this fix.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x32 support for x86-64 from Ingo Molnar:
"This tree introduces the X32 binary format and execution mode for x86:
32-bit data space binaries using 64-bit instructions and 64-bit kernel
syscalls.
This allows applications whose working set fits into a 32 bits address
space to make use of 64-bit instructions while using a 32-bit address
space with shorter pointers, more compressed data structures, etc."
Fix up trivial context conflicts in arch/x86/{Kconfig,vdso/vma.c}
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
x32: Fix alignment fail in struct compat_siginfo
x32: Fix stupid ia32/x32 inversion in the siginfo format
x32: Add ptrace for x32
x32: Switch to a 64-bit clock_t
x32: Provide separate is_ia32_task() and is_x32_task() predicates
x86, mtrr: Use explicit sizing and padding for the 64-bit ioctls
x86/x32: Fix the binutils auto-detect
x32: Warn and disable rather than error if binutils too old
x32: Only clear TIF_X32 flag once
x32: Make sure TS_COMPAT is cleared for x32 tasks
fs: Remove missed ->fds_bits from cessation use of fd_set structs internally
fs: Fix close_on_exec pointer in alloc_fdtable
x32: Drop non-__vdso weak symbols from the x32 VDSO
x32: Fix coding style violations in the x32 VDSO code
x32: Add x32 VDSO support
x32: Allow x32 to be configured
x32: If configured, add x32 system calls to system call tables
x32: Handle process creation
x32: Signal-related system calls
x86: Add #ifdef CONFIG_COMPAT to <asm/sys_ia32.h>
...
Pull nfsd changes from Bruce Fields:
Highlights:
- Benny Halevy and Tigran Mkrtchyan implemented some more 4.1 features,
moving us closer to a complete 4.1 implementation.
- Bernd Schubert fixed a long-standing problem with readdir cookies on
ext2/3/4.
- Jeff Layton performed a long-overdue overhaul of the server reboot
recovery code which will allow us to deprecate the current code (a
rather unusual user of the vfs), and give us some needed flexibility
for further improvements.
- Like the client, we now support numeric uid's and gid's in the
auth_sys case, allowing easier upgrades from NFSv2/v3 to v4.x.
Plus miscellaneous bugfixes and cleanup.
Thanks to everyone!
There are also some delegation fixes waiting on vfs review that I
suppose will have to wait for 3.5. With that done I think we'll finally
turn off the "EXPERIMENTAL" dependency for v4 (though that's mostly
symbolic as it's been on by default in distro's for a while).
And the list of 4.1 todo's should be achievable for 3.5 as well:
http://wiki.linux-nfs.org/wiki/index.php/Server_4.0_and_4.1_issues
though we may still want a bit more experience with it before turning it
on by default.
* 'for-3.4' of git://linux-nfs.org/~bfields/linux: (55 commits)
nfsd: only register cld pipe notifier when CONFIG_NFSD_V4 is enabled
nfsd4: use auth_unix unconditionally on backchannel
nfsd: fix NULL pointer dereference in cld_pipe_downcall
nfsd4: memory corruption in numeric_name_to_id()
sunrpc: skip portmap calls on sessions backchannel
nfsd4: allow numeric idmapping
nfsd: don't allow legacy client tracker init for anything but init_net
nfsd: add notifier to handle mount/unmount of rpc_pipefs sb
nfsd: add the infrastructure to handle the cld upcall
nfsd: add a header describing upcall to nfsdcld
nfsd: add a per-net-namespace struct for nfsd
sunrpc: create nfsd dir in rpc_pipefs
nfsd: add nfsd4_client_tracking_ops struct and a way to set it
nfsd: convert nfs4_client->cl_cb_flags to a generic flags field
NFSD: Fix nfs4_verifier memory alignment
NFSD: Fix warnings when NFSD_DEBUG is not defined
nfsd: vfs_llseek() with 32 or 64 bit offsets (hashes)
nfsd: rename 'int access' to 'int may_flags' in nfsd_open()
ext4: return 32/64-bit dir name hash according to usage type
fs: add new FMODE flags: FMODE_32bithash and FMODE_64bithash
...
Highlights include:
- Fix infinite loops in the mount code
- Fix a userspace buffer overflow in __nfs4_get_acl_uncached
- Fix a memory leak due to a double reference count in rpcb_getport_async()
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yiL7
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes for Linux 3.4 from Trond Myklebust
Highlights include:
- Fix infinite loops in the mount code
- Fix a userspace buffer overflow in __nfs4_get_acl_uncached
- Fix a memory leak due to a double reference count in rpcb_getport_async()
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* tag 'nfs-for-3.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Minor cleanups for nfs4_handle_exception and nfs4_async_handle_error
NFSv4.1: Fix layoutcommit error handling
NFSv4: Fix two infinite loops in the mount code
SUNRPC: Use the already looked-up xprt in rpcb_getport_async()
NFS4.1: remove duplicate variable declaration in filelayout_clear_request_commit
Fix length of buffer copied in __nfs4_get_acl_uncached
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Whenever the station informs the AP that it is about to leave the
operating channel, the timestamp should be recorded. It is handled
in scan resume but not in scan start. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect pointer passed to eir_append_data made mgmt_device_connected
event unparsable by mgmt user space entity.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Pull Ceph updates for 3.4-rc1 from Sage Weil:
"Alex has been busy. There are a range of rbd and libceph cleanups,
especially surrounding device setup and teardown, and a few critical
fixes in that code. There are more cleanups in the messenger code,
virtual xattrs, a fix for CRC calculation/checks, and lots of other
miscellaneous stuff.
There's a patch from Amon Ott to make inos behave a bit better on
32-bit boxes, some decode check fixes from Xi Wang, and network
throttling fix from Jim Schutt, and a couple RBD fixes from Josh
Durgin.
No new functionality, just a lot of cleanup and bug fixing."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (65 commits)
rbd: move snap_rwsem to the device, rename to header_rwsem
ceph: fix three bugs, two in ceph_vxattrcb_file_layout()
libceph: isolate kmap() call in write_partial_msg_pages()
libceph: rename "page_shift" variable to something sensible
libceph: get rid of zero_page_address
libceph: only call kernel_sendpage() via helper
libceph: use kernel_sendpage() for sending zeroes
libceph: fix inverted crc option logic
libceph: some simple changes
libceph: small refactor in write_partial_kvec()
libceph: do crc calculations outside loop
libceph: separate CRC calculation from byte swapping
libceph: use "do" in CRC-related Boolean variables
ceph: ensure Boolean options support both senses
libceph: a few small changes
libceph: make ceph_tcp_connect() return int
libceph: encapsulate some messenger cleanup code
libceph: make ceph_msgr_wq private
libceph: encapsulate connection kvec operations
libceph: move prepare_write_banner()
...
