This patch removes CONFIG_IWL4965_HT #ifdefs for iwl 4965 and 5000. 11n
feature is stable in those drivers and its mode of operation is determined
in mac80211, so this dependency is not needed any more.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mixed use of 'dev' and 'usbdev' for usbnet pointer can be confusing. So changing all 'usbnet *dev' to 'usbnet *usbdev'.
Also remove 'net_device *net' pointer from 'rndis_wext_bind' as 'usbdev->net' were already used where needed.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't queue set_multicast_list work if WORK_SET_MULTICAST_LIST
flag already set.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver wasn't updating netif_carrier on link state changes but assumed
link layer was always up.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() is called from within rndis_command() so it
isn't very good place to do any work. Move to worker thread.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework the alignment check in rt2x00dev.c to be independent of any
potential alignment measures that may be taken before. Just check
whether the payload is aligned based on the pointer addresses.
Note: This is preparatory for the dynamically mapped skb buffers
for the PCI drivers, as these need 4-byte alignment instead of the
currently enforced offset by 2 bytes.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAX_RX_SSI and MAX_NOISE are no longer used,
it is better to remove them entirely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For RTS/CTS-to-self frames the IEEE80211_TX_CTL_USE_RTS_CTS flag
should be cleared for the tx_info flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To really force the FIELD macros to determine
the first bit of the register field we should
use the __builtin_choose_expr() function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not safe to use the skb->cb area for both the rxd and
skb_frame_desc data at the same time, while they occupy an overlapping
piece of memory. This can lead to hard to trace crashes as pointers
within skb_frame_desc are pointing into nowhere, or the rxd data is
overwritten with non-sense.
Fix it by copying the rxd to a small buffer on the stack.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rt2x00pci will be switched over to dynamically mapped skb's
instead of statically allocated DMA buffers, it no longer can handle
alignment of RX packets in a copy step, and needs to implement the
same scheme as rt2x00usb does.
In order to make the patch on dynamically mapped skb's smaller,
already centralize the alignment handling into rt2x00lib. This allows
us to move more code in rt2x00lib, and thus remove code duplication
between rt2x00usb and rt2x00pci.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data and data_len fields aren't really necessary in struct
skb_frame_desc, as they can be deduced from the skb itself.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX queues shouldn't be kicked after each frame that is put into the
queue. This could cause problems during RTS and CTS-to-self as well
as with fragmentation. In all those cases you want all frames to be
send out in a single burst. Off course we shouldn't let the queue fill
up entirely, thus we introduce a 10% threshold which, when reached,
will force the frames to be send out regardless of the frame.
In addition we should prevent queues to become full in such a way
that the tx() handler can fail. Instead of stopping the queue when
it is full, we should stop it when it is below the threshold.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The write_tx_data functions in rt2x00pci and rt2x00usb have
a lot in common. This moves that duplicate code into
rt2x00queue_write_tx_frame().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb_kick_tx_queue() will loop over all entries
within the INDEX_DONE->INDEX range and kick each entry
which is pending to be kicked. This makes the kick_tx_queue
approach work the same as with the PCI drivers which
will allow for more code generalisation into rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qid should be initialized to QID_BEACON and QID_ATIM
for the beacon and atim quue. This makes checking for
a particular queue much saner, and it shouldn't harm,
because the only places where the value is send to
the hardware, we are allowed to send any value we
want since it is only used as argument in the
TX done register.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00_set_field functions are very often used,
but GCC is better able to optimize them when they
are macros instead of static inline functions.
After changing it to macro's each rt2x00 driver will
loose about ~3500 bytes in size.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb doesn't need the TX descriptor in the TX done path.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 doesn't send RTS or CTS-to-self frames through
the tx() callback functions so we don't need to check it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce code duplication by moving led structure initialization
into a per-driver function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reduce goto usage
* Mark if-statements which are true on hardware error unlikely()
* Cleanup debug messages
This makes the code look nicer and be better optimized since
the chance of hardware errors should be very small.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By using __ffs() the register offsets were always calculated
at run-time which all FIELD32/FIELD16 definitions were builtin
constants. This means we can heavily optimize the register handling
by allowing GCC to do all the work during compilation.
Add some compile_ffs() macros to perform the calculation at
compile time. After this each rt2x00 module size is reduced
by ~2500 bytes. And the stack size of several functions is reduced
as well which further limits the number of rt2x00 results in
'make checkstack'.
v2: Merge GertJan's bugfix of patch [1/11] directly into this patch
instead of providing it as seperate patch.
v3: Add extra parentheses when bitshifting __x
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes setting the coherent DMA mask for PCI devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.
The alternative is to select NEW_LEDS, which some drivers do.
This patch fixes the led_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.
This patch fixes the input_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes a WARN_ON that is responsible for the following koops:
http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample
The comment in the patch describes why it's safe to simply remove
the check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
This patch moves the whole struct b43_dmaring struct initialization
right before any DMA allocation operation.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Workaround HW bug for SB600/700 SATA controller PMP support
ahci: workarounds for mcp65
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Revert 'process defer accept as established' changes.
ipv6: Fix duplicate initialization of rawv6_prot.destroy
bnx2x: Updating the Maintainer
net: Eliminate flush_scheduled_work() calls while RTNL is held.
drivers/net/r6040.c: correct bad use of round_jiffies()
fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUP
ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ipg_nic_set_multicast_list()
netfilter: nf_conntrack: fix ctnetlink related crash in nf_nat_setup_info()
netfilter: Make nflog quiet when no one listen in userspace.
ipv6: Fail with appropriate error code when setting not-applicable sockopt.
ipv6: Check IPV6_MULTICAST_LOOP option value.
ipv6: Check the hop limit setting in ancillary data.
ipv6 route: Fix route lifetime in netlink message.
ipv6 mcast: Check address family of gf_group in getsockopt(MS_FILTER).
dccp: Bug in initial acknowledgment number assignment
dccp ccid-3: X truncated due to type conversion
dccp ccid-3: TFRC reverse-lookup Bug-Fix
dccp ccid-2: Bug-Fix - Ack Vectors need to be ignored on request sockets
dccp: Fix sparse warnings
dccp ccid-3: Bug-Fix - Zero RTT is possible
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ramtron FM3130 is a chip with two separate devices inside, RTC clock and
FRAM. This driver provides only RTC functionality.
This chip is met in lots of custom boards with AT91SAMXXXX CPU I work
with, is cheap and in no way better or worse than any other RTC on market.
While it is mostly met on much smaller devices, I think it is great to
have it supported in Linux.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More Kconfig tweaks related to the legacy PC RTC code:
- Describe the legacy PC RTC driver as such ... it's never quite
been clear that this driver is for PC RTCs, and now it's fair
to call this the "legacy" driver.
- Force it to understand about HPET stealing its IRQs ... kernel
code does this always when HPET is in use, there should be no
option for users to goof up the config.
This seems to fix kernel bugzilla #10729.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently (around 2.6.25) I've noticed that RTC no longer works for me. It
turned out this is because I use pnpacpi=off kernel option to work around
the parport_pc bugs. I always did so, but RTC used to work fine in the
past, and now it have regressed.
The patch fixes the problem by creating the platform device for the RTC
when PNP is disabled. This may also help running the PNP-enabled kernel
on an older PCs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several console keyboard maps are broken since
commit 04c7197650
Author: Samuel Thibault <samuel.thibault@ens-lyon.org>
Date: Tue Oct 16 23:27:04 2007 -0700
unicode diacritics support
because that changeset made k_self consider the value as a latin1
character when in Unicode mode, which is wrong; k_self should still take
the console map into account.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic nvram driver announces itself as
'Macintosh non-volatile memory driver'
instead of 'Generic non-volatile memory driver'. Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the cirrusfb driver, the RAM address printk has a superfluous 'x' that
could be interpreted as "don't care", while it is actually a typo. Fix
that.
[akpm@linux-foundation.org: join the two printk strings to make it atomic]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since many distros load this driver by default (throw it against the wall
and see what sticks method). Change the error message severity level to
avoid alarming users. Isn't it annoying when users actually read the
error logs...
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Michael Buesch <mb@bu3sch.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spid has been allocated in this function and so should be freed before
leaving it, as in the other error handling cases.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
@r exists@
expression E,E1;
statement S;
position p1,p2,p3;
@@
E =@p1 \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != E = E1
if (E == NULL || ...) S
... when != E = E1
if@p2 (...) {
... when != kfree(E)
}
... when != E = E1
kfree@p3(E);
@forall@
position r.p2;
expression r.E;
int E1 != 0;
@@
* if@p2 (...) {
... when != kfree(E)
when strict
return E1; }
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With CONFIG_DEBUG_SHIRQ set we will get an interrupt as soon as we
allocate one. Tasklets may be scheduled in the interrupt handler but they
will be initialized after the handler returns, causing a BUG() in
kernel/softirq.c when they run.
Should fix this Fedora bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=449817
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alarm->pending indicates whether there's an alarm that has actually been
triggered, not whether we're waiting for it. alarm->enabled indicates
that.
Also add missing locking around reading the RTC registers.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the next generation of HP Smart Array SAS/SATA
controllers. Shipping date is late Fall 2008.
Bump the driver version to 3.6.20 to reflect the new hardware support from
patch 1 of this set.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Release ports which are requested during detection which are not freed if
there is no hga card. Otherwise there is a crash during cat /proc/ioports
command.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I would like to thank Eliezer Tamir for writing and maintaining the
driver for the past two years. I will take over maintaining the bnx2x
driver from now on.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a compile failure in 2.6.26-rc5-git5.
The variable is expected to be called ofdev.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards, the mv643xx_eth MAC isn't connected to a PHY but
directly (via the MII/GMII/RGMII interface) to another MAC-layer
device. This patch allows specifying ->phy_addr = -1 to skip all
PHY-related initialisation and run-time poking in that case.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
During OOM, instead of stopping RX refill when the rx desc ring is
not empty, keep trying to refill the ring as long as it is not full
instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Some SoCs have the TX bandwidth control registers in a slightly
different place. This patch detects that case at run time, and
re-directs accesses to those registers to the proper place at
run time if needed.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Newer hardware has a 16-bit instead of a 14-bit RX coalescing
count field in the SDMA_CONFIG register. This patch adds a run-time
check for which of the two we have, and adjusts further writes to the
rx coal count field accordingly.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Under some conditions, the TXQ ('TX queue being served') bit can clear
before all packets queued for that TX queue have been transmitted.
This patch enables TXend interrupts, and uses those to re-kick TX
queues that claim to be idle but still have queued descriptors from
the interrupt handler.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
As with the multiple RX queue support, allow the platform code to
specify that the hardware we are running on supports multiple TX
queues. This patch only uses the highest-numbered enabled queue
to send packets to for now, this can be extended later to enable
QoS and such.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Allow the platform code to specify that we are running on hardware
that is capable of supporting multiple RX queues. If this option
is used, initialise all of the given RX queues instead of just RX
queue zero.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Add an interface for the hardware's per-port and per-subqueue
TX rate control. In this stage, this is mainly so that we can
disable the bandwidth limits during initialisation of the port.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
General cleanup of the mv643xx_eth driver. Mainly fixes coding
style / indentation issues, get rid of some useless 'volatile's,
kill some more superfluous comments, and such.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Remove the write-only ->[rt]x_int_coal members from struct
mv643xx_eth_private. In the process, tweak the RX/TX interrupt
mitigation code so that it is compiled by default, and set the
default coalescing delays to 0 usec.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Split all TX queue related state into 'struct tx_queue', in
preparation for multiple TX queue support.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Split all RX queue related state into 'struct rx_queue', in
preparation for multiple RX queue support.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The per-port mv643xx_eth_private struct had a private instance
of struct net_device_stats that was never ever written to, only
read (via the ethtool statistics interface). This patch gets
rid of the private instance, and tweaks the ethtool statistics
code in mv643xx_eth to use the statistics in struct net_device
instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Since they are no longer used, kill enum FUNC_RET_STATUS and
struct pkt_info (which were a rather roundabout way of communicating
RX/TX status within the same driver).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
rx_return_buff() is also a remnant of the HAL layering that the
original mv643xx_eth driver used. Moving it into its caller kills
the last reference to FUNC_RET_STATUS/pkt_info.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The port_receive() function is a remnant of the original mv643xx_eth
HAL split. This patch moves port_receive() into its caller, so that
the top and the bottom half of RX processing no longer communicate
via the HAL FUNC_RET_STATUS/pkt_info mechanism abstraction anymore.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Half of the functions in the mv643xx_eth driver are prefixed by
useless and baroque comment blocks on _what_ those functions do (which
is obvious from the code itself) rather than why, and there's no point
in keeping those comments around.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
A bunch of places in the mv643xx_eth driver use the 'mv643xx_'
prefix. Since the mv643xx is a chip that includes more than just
ethernet, this patch makes all those places use either no prefix
(for some internal-use-only functions), or the full 'mv643xx_eth_'
prefix.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The fact that mv643xx_eth is an ethernet driver is pretty obvious,
and having a lot of internal-use-only functions and defines prefixed
with ETH_/ethernet_/eth_ prefixes is rather pointless. So, get rid
of most of those prefixes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Remove the unused rx/tx descriptor field defines, and move the ones
that are actually used to the actual definitions of the rx/tx
descriptor format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
All except one of the port serial status register bit defines are
unused -- kill the unused ones.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The only user of the ETH_MIB_VERY_LONG_NAME_HERE defines is the
eth_update_mib_counters() function. Get rid of the defines by
open-coding the register offsets in the latter.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Get rid of RX_BUF_OFFSET (which is synonymous with ETH_HW_IP_ALIGN).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Replace the nondescriptive names ETH_INT_UNMASK_ALL and
ETH_INT_UNMASK_ALL_EXT by names of the actual fields being masked
and unmasked in the various writes to the interrupt mask registers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
None of the port status register bit defines are ever used in the
mv643xx_eth driver -- nuke them all.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Over half of the port serial control register bit defines are never
used, and the PORT_SERIAL_CONTROL_DEFAULT_VALUE define is never used
either. Keep only those defines that are actually used.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Delete the defines for SDMA config register bit values that are
never used in the driver, to tidy up the code some more.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The port config extend register is never changed at run time.
Document the meaning of the initial value, and delete the defines
for the individual bits in this register.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
The mv643xx_eth driver only ever changes bit 0 of the port config
register at run time, the rest of the register bits are fixed (and
always zero). Document the meaning of the chosen default value,
and get rid of all the defines for each of the individual bits.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Shorten the various oversized register names in mv643xx_eth.c, to
increase readability.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
This patch performs a reverse topological sort of all functions in
mv643xx_eth.c, so that we can get rid of all forward declarations,
and end up with a more understandable driver due to related functions
being grouped together.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
This patch removes CVS keyword that weren't updated for a long time.
One of them was printed as part of a printk, which also doesn't make
much sense for a 5 year old and no longer updated keyword.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to other places in the kernel, I think that this driver misuses
the function round_jiffies.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The branches are dead code. even when dev->flag IFF_MULTICAST (defined
0x1000) is set, dev->flags & IFF_MULTICAST & [boolean] always evaluates to
0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
From: tony@bakeyournoodle.com (Tony Breeds)
The commit 3f8cb09885
(drivers/net/lib8390: fix warning, trim trailing whitespace) removed
ei_local from ei_tx_err() and ei_rx_overrun() resulting in the following
build errors on m68k and sh:
Using /scratch1/tony/next as source for kernel
GEN /scratch1/tony/next_out/Makefile
CHK include/linux/version.h
CHK include/linux/utsrelease.h
CALL /scratch1/tony/next/scripts/checksyscalls.sh
CHK include/linux/compile.h
CC [M] drivers/net/zorro8390.o
In file included from /scratch1/tony/next/drivers/net/zorro8390.c:47:
drivers/net/lib8390.c: In function 'ei_tx_err':
drivers/net/lib8390.c:556: error: 'ei_local' undeclared (first use in this function)
drivers/net/lib8390.c:556: error: (Each undeclared identifier is reported only once
drivers/net/lib8390.c:556: error: for each function it appears in.)
drivers/net/lib8390.c: In function 'ei_rx_overrun':
drivers/net/lib8390.c:823: error: 'ei_local' undeclared (first use in this function)
make[3]: *** [drivers/net/zorro8390.o] Error 1
make[2]: *** [drivers/net] Error 2
make[1]: *** [drivers] Error 2
make: *** [sub-make] Error 2
The problem is that ei_inb_p() is using various #defines (from
drivers/net/8390.h) that use EI_SHIFT, which in some drivers on some
architectures use ei_local. Tag ei_local as "__maybe_unused" to keep it
around and keep the warnings the original commit is trying to silence
... silenced.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
deivces, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This driver is for a number of different Option devices. Originally
written by Option and Andrew Bird, but cleaned up massivly for
acceptance into mainline by me and others.
Many thanks to the following for their help in cleaning up the driver by
providing feedback and patches to it:
- Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
- Oliver Neukum <oliver@neukum.org>
- Alan Cox <alan@lxorguk.ukuu.org.uk>
- Javier Marcet <javier@krausbeck.org>
Cc: Andrew Bird <ajb@spheresystems.co.uk>
Cc: Javier Marcet <javier@krausbeck.org>
Cc: Filip Aben <f.aben@option.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes the following needlessly global functions static:
- macsonic_init()
- mac_onboard_sonic_ethernet_addr()
- mac_onboard_sonic_probe()
- mac_nubus_sonic_ethernet_addr()
- macsonic_ident()
- mac_nubus_sonic_probe()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch removes write-only global "last_dev" variables from the
following drivers:
- a2065.c
- declance.c
- sunlance.c
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes the following needlessly global functions static:
- mac8390_ident()
- mac8390_testio()
- mac8390_memsize()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes the needlessly global hplance_{init,cleanup}_module()
static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes the needlessly global lance_addr_list[] static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We should use a random mac address if the EEPROM doesn't contain a valid
one. This makes life on Boards with unprogrammed EEPROM devices easier.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for Renesas SuperH Ethernet controller. This driver supports
SH7710 and SH7712.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable the smc911x driver for the SuperH architecture. While at it remove
the unused SMC_USE_SH_DMA definition.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a new header file for platform data information
together with code that adds run time bus width and irq flag support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch contains changes needed for platform data support:
- Move smc911x_local structure to header file
- Pass along smc911x_local structure pointer to macros
- Keep register base address in smc911x_local structure
- Remove unused ioaddr variables
[m.kozlowski@tuxland.pl: Parenthesis fix in drivers/net/smc911x.h]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes the following issues related to 16-bit support:
- Remove unused 16-bit PXA DMA implementation.
- Remove unused SMC_inw() and SMC_outw() functions.
- Fix 16-bit SMC_outl to use writew() instead of writel().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unused SMC_inb() and SMC_outb() functions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: don't use reset-resume if drivers don't support it
USB: isp1760: Assign resource fields before adding hcd
isight_firmware: Avoid crash on loading invalid firmware
USB: fix build bug in USB_ISIGHTFW
This patch tries to identify which devices are able to accept
reset-resume handling, by checking that there is at least one
interface driver bound and that all of the drivers have a reset_resume
method defined. If these conditions don't hold then during resume
processing, the device is logicall disconnected.
This is only a temporary fix. Later on we will explicitly unbind
drivers that can't handle reset-resumes.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the bogus "io mem 0x00000000" message printed
during driver init due to hcd->rsrc_start being assigned after
the call to usb_add_hcd().
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Different tools generate slightly different formats of the isight
firmware. Ensure that the firmware buffer is not overrun, while still
ensuring that the correct amount of data is written if trailing data is
present.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Report-by: Justin Mattock <justinmattock@gmail.com>
Tested-by: Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: fix build bug in USB_ISIGHTFW
-tip tree testing found this build bug:
drivers/built-in.o: In function `isight_firmware_load':
isight_firmware.c:(.text+0x1ade08): undefined reference to `request_firmware'
isight_firmware.c:(.text+0x1adf9c): undefined reference to `release_firmware'
select FW_LOADER in USB_ISIGHTFW.
From: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix kernel-doc for new dev_set_name() function:
Warning(lin2626-rc5//drivers/base/core.c:767): No description found for parameter 'fmt'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My laptop thinks that it's a good idea to give -73C as the critical
CPU temperature.... which isn't the best thing since it causes a shutdown
right at bootup.
Temperatures below freezing are clearly invalid critical thresholds
so just reject these as such.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes problem introduced in 20080123, with fix for Unload operator.
Parse tree object can be already deleted; must use the opcode
within the WalkState.
ACPI: kmemcheck: Caught 16-bit read from freed memory
http://bugzilla.kernel.org/show_bug.cgi?id=10669
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem introduced in 20080514 where the status of
execution of _SST is incorrectly returned to the caller. _SST
is optional, and if it is AE_NOT_FOUND, the exception should be
ignored.
http://www.acpica.org/bugzilla/show_bug.cgi?id=716
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts a change introduced in version 20071019. The table
is now loaded at the namespace root even though this goes against
the ACPI specification. This provides compatibility with other
ACPI implementations.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Only "SSDT" is acceptable to the ACPI spec, but tables are
seen with OEMx and null sigs. Therefore, signature validation
is worthless. Apparently MS ACPI accepts such signatures, ACPICA
must be compatible.
http://bugzilla.kernel.org/show_bug.cgi?id=10454
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Allows null field list in Field(), BankField(), and IndexField().
2.6.26-rc1 regression: ACPI fails to load SDT. - Dell M1530
http://bugzilla.kernel.org/show_bug.cgi?id=10606
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
If acpi_install_notify_handler() for a bay device fails, the bay driver is
superfluous. Most likely, another driver (like libata) is already caring
about this device anyway. Furthermore,
register_hotplug_dock_device(acpi_handle) from the dock driver must not be
called twice with the same handler. This would result in an endless loop
consuming 100% of CPU. So clean up and exit.
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a proper prototype for acpi_processor_tstate_has_changed()
in include/acpi/processor.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a SLIT sanity checking patch. It moves slit_valid() function to
generic ACPI code and does sanity checking for both x86 and ia64. It sets up
node_distance with LOCAL_DISTANCE and REMOTE_DISTANCE when hitting invalid
SLIT table on ia64. It also cleans up unused variable localities in
acpi_parse_slit() on x86.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
When configuring the resources of an ACPI device, we first evaluate _CRS
to get a template of resource descriptors, then fill in the specific
resource values we want, and finally evaluate _SRS to actually configure
the device.
Some resources have optional fields, so the size of encoded descriptors
varies depending on the specific values. For example, IRQ descriptors can
be either two or three bytes long. The third byte contains triggering
information and can be omitted if the IRQ is edge-triggered and active
high.
The BIOS often assumes that IRQ descriptors in the _SRS buffer use the
same format as those in the _CRS buffer, so this patch enforces that
constraint.
The "Start Dependent Function" descriptor also has an optional byte, but
we don't currently encode those descriptors, so I didn't do anything for
those.
I have tested this patch on a Toshiba Portege 4000. Without the patch,
parport_pc claims the parallel port only if I use "pnpacpi=off". This
patch makes it work with PNPACPI.
This is an extension of a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c42
References:
http://bugzilla.kernel.org/show_bug.cgi?id=5832 Enabling ACPI Plug and Play in kernels >2.6.9 kills Parallel support
http://bugzilla.kernel.org/show_bug.cgi?id=9487 buggy firmware expects four-byte IRQ resource descriptor (was: Serial port disappears after Suspend on Toshiba R25)
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=1d5b285da1893b90507b081664ac27f1a8a3dc5b related ACPICA fix
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
When we encode IRQ resources, we should use the "shareable" flag we got
from _PRS rather than guessing based on the IRQ trigger mode.
This is based on a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c32
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
As of recently (probably 2.6.26-rc1) I've been getting the following mangling
in the kernel log:
[4294014.568167] ACPI: DSDT override uses original SSDTs unless "acpi_no_auto_ssdt"<6>CPU0: Intel(R) Pentium(R) Dual CPU E2160 @ 1.80GHz stepping 0d
This is due to a missing newline character in the first message. The following
patch against 2.6.26-rc2 fixes it. Please apply.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
The less tested codepaths for LED handling, used on ThinkPads 570, 600e/x,
770e, 770x, A21e, A2xm/p, T20-22, X20 and maybe a few others, would write
data to kernel memory it had no business touching, for leds number 3 and
above. If one is lucky, that illegal write would cause an OOPS, but
chances are it would silently corrupt a byte.
The problem was introduced in commit af116101, "ACPI: thinkpad-acpi: add
sysfs led class support to thinkpad leds (v3.2)".
Fix the bug by refactoring the entire code to be far more obvious on what
it wants to do. Also do some defensive "constification".
Issue reported by Karol Lewandowski <lmctlx@gmail.com> (he's an lucky guy
and got an OOPS instead of silent corruption :-) ).
Root cause of the OOPS identified by Adrian Bunk <bunk@kernel.org>.
Thanks, Adrian!
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Tested-by: Karol Lewandowski <lmctlx@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rework some subdriver init and exit handlers, in order to fix some
initialization error paths that were missing, or broken.
Hitting those bugs should be extremely rare in the real world, but should
that happen, thinkpad-acpi would fail to dealocate some resources and a
reboot might well be needed to be able to load the driver again.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename SW_RADIO to SW_RFKILL_ALL in thinkpad-acpi code and docs, following
5adad01339 "Input: rename SW_RADIO to
SW_RFKILL_ALL".
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
cpuidle and acpi driver interaction bug with the way cpuidle_register_driver()
is called. Due to this bug, there will be oops on
AC<->DC on some systems, where they support C-states in one DC and not in AC.
The current code does
ON BOOT:
Look at CST and other C-state info to see whether more than C1 is
supported. If it is, then acpi processor_idle does a
cpuidle_register_driver() call, which internally enables the device.
ON CST change notification (AC<->DC) and on suspend-resume:
acpi driver temporarily disables device, updates the device with
any new C-states, and reenables the device.
The problem is is on boot, there are no C2, C3 states supported and we skip
the register. Later on AC<->DC, we may get a CST notification and we try
to reevaluate CST and enabled the device, without actually registering it.
This causes breakage as we try to create /sys fs sub directory, without the
parent directory which is created at register time.
Thanks to Sanjeev for reporting the problem here.
http://bugzilla.kernel.org/show_bug.cgi?id=10394
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Fixed_RTC event should be disabled when installing RTC handler.
Only when RTC alarm is set will it be enabled again. If it is not
disabled, maybe some machines will be powered on automatically after
the system is shutdown even when the RTC alarm is not set.
http://bugzilla.kernel.org/show_bug.cgi?id=10010
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch correct a typo error in pxafb vhich is relevant for 8-bit palette framebuffer configuration.
Signed-off-by: Jrgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: MMU: Fix is_empty_shadow_page() check
KVM: MMU: Fix printk() format string
KVM: IOAPIC: only set remote_irr if interrupt was injected
KVM: MMU: reschedule during shadow teardown
KVM: VMX: Clear CR4.VMXE in hardware_disable
KVM: migrate PIT timer
KVM: ppc: Report bad GFNs
KVM: ppc: Use a read lock around MMU operations, and release it on error
KVM: ppc: Remove unmatched kunmap() call
KVM: ppc: add lwzx/stwz emulation
KVM: ppc: Remove duplicate function
KVM: s390: Fix race condition in kvm_s390_handle_wait
KVM: s390: Send program check on access error
KVM: s390: fix interrupt delivery
KVM: s390: handle machine checks when guest is running
KVM: s390: fix locking order problem in enable_sie
KVM: s390: use yield instead of schedule to implement diag 0x44
KVM: x86 emulator: fix hypercall return value on AMD
KVM: ia64: fix zero extending for mmio ld1/2/4 emulation in KVM
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
net: Fix routing tables with id > 255 for legacy software
sky2: Hold RTNL while calling dev_close()
s2io iomem annotations
atl1: fix suspend regression
qeth: start dev queue after tx drop error
qeth: Prepare-function to call s390dbf was wrong
qeth: reduce number of kernel messages
qeth: Use ccw_device_get_id().
qeth: layer 3 Oops in ip event handler
virtio: use callback on empty in virtio_net
virtio: virtio_net free transmit skbs in a timer
virtio: Fix typo in virtio_net_hdr comments
virtio_net: Fix skb->csum_start computation
ehea: set mac address fix
sfc: Recover from RX queue flush failure
add missing lance_* exports
ixgbe: fix typo
forcedeth: msi interrupts
ipsec: pfkey should ignore events when no listeners
pppoe: Unshare skb before anything else
...
