Impact: find right nr_irqs_gsi on some systems.
One test-system has gap between gsi's:
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfeafd000] gsi_base[48])
[ 0.000000] IOAPIC[1]: apic_id 5, version 0, address 0xfeafd000, GSI 48-54
[ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfeafc000] gsi_base[56])
[ 0.000000] IOAPIC[2]: apic_id 6, version 0, address 0xfeafc000, GSI 56-62
...
[ 0.000000] nr_irqs_gsi: 38
So nr_irqs_gsi is not right. some irq for MSI will overwrite with io_apic.
need to get that with acpi_probe_gsi when acpi io_apic is used
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make check-timer more robust potentially solve boot fragility
For edge trigger io-apic routing, we already unmasked the pin via
setup_IO_APIC_irq(), so don't unmask it again.
Also call local_irq_disable() between timer_irq_works(), because it
calls local_irq_enable() inside.
Also remove not needed apic version reading for 64-bit
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make nr_irqs depend more on cards used in a system
depend on nr_irq_gsi more, and have a ratio for MSI.
v2: make nr_irqs less than NR_VECTORS * nr_cpu_ids
aka if only one cpu, we only can support nr_irqs = NR_VECTORS
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
disable_ioapic_setup() in init/main.c is ugly as the function is
x86-specific. The #ifdef inline prototype there is ugly too.
Replace it with a generic arch_disable_smp_support() function - which
has a weak alias for non-x86 architectures and for non-ioapic x86 builds.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Eric Paris reported:
> I have an hp dl785g5 which is unable to successfully run
> 2.6.29-0.66.rc3.fc11.x86_64 or 2.6.29-rc2-next-20090126. During bootup
> (early in userspace daemons starting) I get the below BUG, which quickly
> renders the machine dead. I assume it is because sparse_irq_lock never
> gets released when the BUG kills that task.
Adjust lock sequence when migrating a descriptor with
CONFIG_NUMA_MIGRATE_IRQ_DESC enabled.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the 32-bit subarchitecture support code.
All subarchitectures but Voyager have been converted. Voyager will be
done later or will be removed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Our send_IPI_*() methods and definitions are a twisted mess: the same
symbol is defined to different things depending on .config details,
in a non-transparent way.
- spread out the quirks into separately named per apic driver methods
- prefix the standard PC methods with default_
- get rid of wrapper macro obfuscation
- clean up various details
Signed-off-by: Ingo Molnar <mingo@elte.hu>
only NUMAQ uses this quirk: to prevent the timer IRQ from being added
on secondary nodes.
All other genapic templates can have a NULL ->multi_timer_check()
callback.
Also, extend the generic code to treat a NULL pointer accordingly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
The bigsmp and es7000 subarchitectures un-defined APIC_DEST_LOGICAL in
a rather nasty way by re-defining it to zero. That is infinitely
fragile and makes it very hard to see what to code really does in
a given context. The very same constant has different meanings and
values - depending on which subarch is enabled.
Untangle this mess by never undefining the constant, but instead
propagating the right values into the genapic driver templates.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the wrapper macros IRQ_DEST_MODE and IRQ_DELIVERY_MODE.
The typical 32-bit and the 64-bit build all dereference via the genapic,
so it's pointless to hide that indirection via these ugly macros.
Furthermore, it also obscures subarchitecture details.
So replace it with apic->irq_dest_mode / etc. accesses.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
int_delivery_mode is supposed to mean 'interrupt delivery mode', but
it's quite a misnomer as 'int' we usually think of as an integer type ...
The standard naming for such attributes is 'irq' - so rename the following
fields and macros:
int_delivery_mode => irq_delivery_mode
INT_DELIVERY_MODE => IRQ_DELIVERY_MODE
int_dest_mode => irq_dest_mode
INT_DEST_MODE => IRQ_DEST_MODE
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename genapic-> to apic-> references because in a future chagne we'll
open-code all the indirect calls (instead of obscuring them via macros),
so we want this reference to be as short as possible.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make X86 SGI Ultraviolet support configurable. Saves about 13K of text size
on my modest config.
text data bss dec hex filename
6770537 1158680 694356 8623573 8395d5 vmlinux
6757492 1157664 694228 8609384 835e68 vmlinux.nouv
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since commit 75c46fa, "x64, x2apic/intr-remap: MSI and MSI-X
support for interrupt remapping infrastructure", x86 has had an
implementation of arch_setup_msi_irqs().
That implementation does not call arch_setup_msi_irq(), instead it calls
setup_irq(). No other x86 code calls arch_setup_msi_irq().
That leaves only arch_setup_msi_irqs() in drivers/pci/msi.c, but that
routine is overridden by the x86 version of arch_setup_msi_irqs().
So arch_setup_msi_irq() is dead code, remove it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: widen the effect of the 'nolapic' boot parameter
"nolapic" should not only suppress SMP and use of the LAPIC, but it
also ought to have the effect of disabling all IO-APIC related activity
as well as PCI MSI and HT-IRQs.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: preparation, cleanup, add KERN_INFO printk
Modify references from NR_IRQS to nr_irqs as the later will become
variable-sized based on nr_cpu_ids when CONFIG_SPARSE_IRQS=y.
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: reduce memory usage, use new cpumask API.
Replace the affinity and pending_masks with cpumask_var_t's. This adds
to the significant size reduction done with the SPARSE_IRQS changes.
The added functions (init_alloc_desc_masks & init_copy_desc_masks) are
in the include file so they can be inlined (and optimized out for the
!CONFIG_CPUMASKS_OFFSTACK case.) [Naming chosen to be consistent with
the other init*irq functions, as well as the backwards arg declaration
of "from, to" instead of the more common "to, from" standard.]
Includes a slight change to the declaration of struct irq_desc to embed
the pending_mask within ifdef(CONFIG_SMP) to be consistent with other
references, and some small changes to Xen.
Tested: sparse/non-sparse/cpumask_offstack/non-cpumask_offstack/nonuma/nosmp on x86_64
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: virtualization@lists.osdl.org
Cc: xen-devel@lists.xensource.com
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
Impact: Reduce inter-node memory traffic.
Reduces inter-node memory traffic (offloading the global system bus)
by allocating referenced struct cpumasks on the same node as the
referring struct.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce printk noise
The message "alloc irq_2_pin on cpu 0 node 0" is printed way too often.
% dmesg|grep irq_2_pin|wc -l
20
Get rid of the debug printks.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
* 'irq-fixes-for-linus-4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sparseirq: move __weak symbols into separate compilation unit
sparseirq: work around __weak alias bug
sparseirq: fix hang with !SPARSE_IRQ
sparseirq: set lock_class for legacy irq when sparse_irq is selected
sparseirq: work around compiler optimizing away __weak functions
sparseirq: fix desc->lock init
sparseirq: do not printk when migrating IRQ descriptors
sparseirq: remove duplicated arch_early_irq_init()
irq: simplify for_each_irq_desc() usage
proc: remove ifdef CONFIG_SPARSE_IRQ from stat.c
irq: for_each_irq_desc() move to irqnr.h
hrtimer: remove #include <linux/irq.h>
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, sparseirq: clean up Kconfig entry
x86: turn CONFIG_SPARSE_IRQ off by default
sparseirq: fix numa_migrate_irq_desc dependency and comments
sparseirq: add kernel-doc notation for new member in irq_desc, -v2
locking, irq: enclose irq_desc_lock_class in CONFIG_LOCKDEP
sparseirq, xen: make sure irq_desc is allocated for interrupts
sparseirq: fix !SMP building, #2
x86, sparseirq: move irq_desc according to smp_affinity, v7
proc: enclose desc variable of show_stat() in CONFIG_SPARSE_IRQ
sparse irqs: add irqnr.h to the user headers list
sparse irqs: handle !GENIRQ platforms
sparseirq: fix !SMP && !PCI_MSI && !HT_IRQ build
sparseirq: fix Alpha build failure
sparseirq: fix typo in !CONFIG_IO_APIC case
x86, MSI: pass irq_cfg and irq_desc
x86: MSI start irq numbering from nr_irqs_gsi
x86: use NR_IRQS_LEGACY
sparse irq_desc[] array: core kernel and x86 changes
genirq: record IRQ_LEVEL in irq_desc[]
irq.h: remove padding from irq_desc on 64bits
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/io_apic.c:709:6: warning: symbol 'io_apic_sync' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix panic on null pointer with sparseirq
Some GCC versions seem to inline the weak global function,
when that function is empty.
Work it around, by making the functions return a (dummy) integer.
Signed-off-by: Yinghai <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
all for_each_irq_desc() usage point have !desc check.
then its check can move into for_each_irq_desc() macro.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
