Change USER/KERNEL_DS so that the merged version of
__strnlen_user can be used which allows us to complete the
removal of arch/ppc64/lib/.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
We had a static memory_limit in prom.c, and then another one defined
in setup_64.c and used in numa.c, which resulted in the kernel crashing
when mem=xxx was given on the command line. This puts the declaration
in system.h and the definition in mem.c. This also moves the
definition of tce_alloc_start/end out of setup_64.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the phys_mem_access_prot() function to take a pfn instead of an
address. This allows mmap64() to work on /dev/mem for addresses above 4G
on 32-bit architectures. We start with a pfn in mmap_mem(), so there's no
need to convert to an address; in fact, it's actively bad, since the
conversion can overflow when the address is above 4G.
Similarly fix the ppc32 page_is_ram() function to avoid a conversion to an
address by directly comparing to max_pfn. Working with max_pfn instead of
high_memory fixes page_is_ram() to give the right answer for highmem pages.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The merged version follows the ppc64 version pretty closely mostly,
and in fact ARCH=ppc64 now uses the arch/powerpc/xmon version.
The main difference for ppc64 is that the 'p' command to call
show_state (which was always pretty dodgy) has been replaced by
the ppc32 'p' command, which calls a given procedure (so in fact
the old 'p' command behaviour can be achieved with 'p $show_state').
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sc instruction emulation can't be done the same way on 32-bit
as 64-bit yet, but this should work OK.
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 32-bit platforms, these convert from kernel virtual addresses
to real (physical addresses), like tophys/tovirt but they use
the same register for the source and destination. On 64-bit
platforms, they do nothing because the hardware ignores the top
two bits of the address in real mode.
These new macros are used in fpu.S now.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In readiness for 64k pages, when THREAD_SIZE will be less than
PAGE_SIZE, ppc64 uses kmalloc() rather than __get_free_pages() to
allocate kernel stacks, and since thread_info.h was merged, so does
ppc32. However that adds some overhead which we don't really want
when PAGE_SIZE <= THREAD_SIZE (including all ppc32 machines), so this
patch avoids it.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Save for the header #define, ppc32 and ppc64 versions of parport.h are
identical. This patch merges them.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent merge of fpu.S broken the handling of fpscr for
ARCH=powerpc and CONFIG_PPC64=y. FP registers could be corrupted,
leading to strange random application crashes.
The confusion arises, because the thread_struct has (and requires) a
64-bit area to save the fpscr, because we use load/store double
instructions to get it in to/out of the FPU. However, only the low
32-bits are actually used, so we want to treat it as a 32-bit quantity
when manipulating its bits to avoid extra load/stores on 32-bit. This
patch replaces the current definition with a structure of two 32-bit
quantities (pad and val), to clarify things as much as is possible.
The 'val' field is used when manipulating bits, the structure itself
is used when obtaining the address for loading/unloading the value
from the FPU.
While we're at it, consolidate the 4 (!) almost identical versions of
cvt_fd() and cvt_df() (arch/ppc/kernel/misc.S,
arch/ppc64/kernel/misc.S, arch/powerpc/kernel/misc_32.S,
arch/powerpc/kernel/misc_64.S) into a single version in fpu.S. The
new version takes a pointer to thread_struct and applies the correct
offset itself, rather than a pointer to the fpscr field itself, again
to avoid confusion as to which is the correct field to use.
Finally, this patch makes ARCH=ppc64 also use the consolidated fpu.S
code, which it previously did not.
Built for G5 (ARCH=ppc64 and ARCH=powerpc), 32-bit powermac (ARCH=ppc
and ARCH=powerpc) and Walnut (ARCH=ppc, CONFIG_MATH_EMULATION=y).
Booted on G5 (ARCH=powerpc) and things which previously fell over no
longer do.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There has been a need expressed for dma_addr_t to be 64 bits on PPC64.
This patch does that.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent addition of __deprecated to the declarations for
find_devices etc. produces a whole pile of warnings from the
ppc32 code. Since those functions still work perfectly well on
ppc32, which doesn't have hotplug support for anything in the
OF device tree, and we don't have time to fix that code now,
remove the __deprecated markings for now.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The interrupt-tree parsing code wasn't offsetting interrupt numbers
by 16 on 32-bit platforms with an i8259 interrupt controller, and
it was confused about the encoding of interrupt sense and level
(which is different for i8259 and openpic interrupt controllers,
just to make things interesting).
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is so that the 32-bit CHRP code can use it. The MPC106
initialization code is now in arch/powerpc/sysdev/grackle.c and
is controlled by CONFIG_PPC_MPC106.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the parameters for i8259_init so that it takes two
parameters: a physical address for generating an interrupt
acknowledge cycle, and an interrupt number offset. i8259_init
now sets the irq_desc[] for its interrupts; all the callers
were doing this, and that code is gone now. This also defines
a CONFIG_PPC_I8259 symbol to select i8259.o for inclusion, and
makes the platforms that need it select that symbol.
Signed-off-by: Paul Mackerras <paulus@samba.org>
GCC 3.3.3 barfs on the trailing \n" in the HMT macros.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somewhere along the line we got two definitions of set_tb(). They look to
be identical although they're not textually identical. So remove the #ifdef
CONFIG_PPC64 version, leaving the common version in time.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powerpc: Fix types.h
I noticed that Paul had already pulled the version of types.h that
is missing the config.h include into the merge tree - this patch adds
it back in.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On !CONFIG_PPC_MULTIPLATFORM _machine is defined as 0. This is ok, but
we can't assign a value to _machine then.
We may not have CONFIG_PCI available, so only build in support for
find_parent_pci_resource(), request_OF_resource(), release_OF_resource()
if PCI is enabled. This is probably not the long term fix but works out
for now.
Make reg_property64 contain 64-bit elements on a 32-bit machine.
Mark the deprecated prom.c functions as __deprecated.
Signed-off-by: Kumar K. Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a shutdown member to struct vio_driver. We also need vio_bus_shutdown()
which converts from struct device to struct vio_dev and knows how to extract
the struct vio_driver.
Original patch adjusted for different location of vio.c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Just set the name field directly in the device_driver structure
contained in the vio_driver struct.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Move include/asm-ppc64/vio.h to include/asm-powerpc/vio.h, that's it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
The 601 doesn't have the timebase register; instead it has an RTCL
register that counts nanoseconds and wraps at 1000000000, and an
RTCU register that counts seconds. This makes the necessary changes
for the merged time code to use the RTCL/U registers when the kernel
is running on a 601.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This brings in a lot of changes from arch/ppc64/kernel/pmac_*.c to
arch/powerpc/platforms/powermac/*.c and makes various minor tweaks
elsewhere. On the powermac we now initialize ppc_md by copying
the whole pmac_md structure into it, which required some changes in
the ordering of initializations of individual fields of it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously it ignored the return value from ppc_md.set_rtc_time,
but in fact the functions that that can point to do return a
useful error code, so return it from set_rtc_time().
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves smp_space_timers from arch/ppc64/kernel/smp.c to
arch/powerpc/kernel/time.c and makes it initialize last_jiffy[]
instead of paca[].next_jiffy_update_tb, since last_jiffy[] is
now what the time code uses. It also declares smp_space_timers
in include/asm-powerpc/time.h and gets rid of an ifdef in
div128_by_32.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge ppc32 and ppc64 versions of thread_info.h. They were pretty
similar already, the chief changes are:
- Instead of inline asm to implement current_thread_info(),
which needs to be different for ppc32 and ppc64, we use C with an
asm("r1") register variable. gcc turns it into the same asm as we
used to have for both platforms.
- We replace ppc32's 'local_flags' with the ppc64
'syscall_noerror' field. The noerror flag was in fact the only thing
in the local_flags field anyway, so the ppc64 approach is simpler, and
means we only need a load-immediate/store instead of load/mask/store
when clearing the flag.
- In readiness for 64k pages, when THREAD_SIZE will be less
than a page, ppc64 used kmalloc() rather than get_free_pages() to
allocate the kernel stack. With this patch we do the same for ppc32,
since there's no strong reason not to.
- For ppc64, we no longer export THREAD_SHIFT and THREAD_SIZE
via asm-offsets, thread_info.h can now be safely included in asm, as
on ppc32.
Built and booted on G4 Powerbook (ARCH=ppc and ARCH=powerpc) and
Power5 (ARCH=ppc64 and ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I had the sense of the test for when to use the old 601-style RTC
registers inverted. pmac_calibrate_decr and via_calibrate_decr
weren't setting ppc_tb_freq, on which all the further calculations
depended. Lastly, update_gtod was losing the top 32 bits of
the new tb_to_xs value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This declares powersave_nap in system.h and makes it an int everywhere,
fixes typos for the maple platform, fixes a couple of places where
I missed removing the last two arguments from a message_pass function,
and makes ppc64 consistent with ppc32 in the type of the
pci_bridge.cfg_data field.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Except for smu.h, which moved from asm-ppc64 to asm-powerpc, all
of these moved from asm-ppc to asm-powerpc. In each case the
asm-ppc64 version (if there was one) was just a single line
including the asm-ppc version.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having it here rather than in arch/ppc64/kernel/smp.c means that
we can use it on 32-bit SMP systems easily with ARCH=powerpc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges types.h into include/asm-powerpc. The only real change is
the removal of the include of linux/config.h from the 32-bit version - it
doesn't appear to be necessary.
This patch has been built on several different 32 and 64-bit platforms,
and booted on mpc8540_ads.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patches the ppc32 and ppc64 versions of the headers and .c files
with helper functions for manipulating the performance counting
hardware. As a side effect, it removes use of the term "perfmon" from
ppc32, thus avoiding confusion with the unrelated performance counter
interface from HP Labs also called "perfmon".
Built, but not booted, for g5, pSeries, iSeries, and 32-bit Powermac
with both ARCH=powerpc and ARCH=ppc{,64} as appropriate.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We now use the merged time.c for both 32-bit and 64-bit compilation
with ARCH=powerpc, and for ARCH=ppc64, but not for ARCH=ppc32.
This removes setup_default_decr (folds its function into time_init)
and moves wakeup_decrementer into time.c. This also makes an
asm-powerpc/rtc.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few things change for consistency between ppc32 and ppc64:
idle functions return void; *_get_boot_time functions return
unsigned long (i.e. time_t) rather than filling in a struct rtc_time
(since that's useful to the callers and easier for pmac to
generate); *_get_rtc_time and *_set_rtc_time functions take
a struct rtc_time; irq_canonicalize is gone; nvram_sync returns
void.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The only real user of this file outside platforms/iseries was
drivers/net/iseries_veth.c but all it wanted was ISERIES_HV_ADDR()
so we move that to abs_addr.h (and lowercase it).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Interestingly enough, ppc32 had broken timekeeping for ages... It
worked, but probably drifted a bit more than could be explained by the
actual bad precision of the timebase calibration. We discovered that
recently when somebody figured out that the common code was using
CLOCK_TICK_RATE to correct the timekeeing, and ppc32 had a completely
bogus value for it.
This patch turns it into something saner. Probably not as good as doing
something based on the actual timebase frequency precision but I'll
leave that sort of math to others. This at least makes it better for
the common HZ values.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
