Commit Graph

117 Commits

Author SHA1 Message Date
Guennadi Liakhovetski
574ec547c7 ARM: add support for the EET board, based on the i.MX31 pcm037 module
The "EET" variant of the pcm037 board has an OLED display, using a S6E63D6
display controller on the first SPI interface, using GPIO57 as a chip-select
for it. S6E63D6 is initialised in the boot-loader, so we only have to take care
of the LCD. EET also adds several buttons and LEDs on GPIOs. This patch adds a
"pcm037_variant=" kernel command line parameter to specify at boot-time which
board the kernel is running on, default is "pcm970", specify "eet" for the EET
board.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-23 14:25:26 +02:00
Guennadi Liakhovetski
32c1ad9ab2 pcm037: add MT9T031 camera support
Add support for the MT9T031 CMOS camera sensor from Aptina to the PCM037
board. Also add two I2C iomux pin definitions, needed for pcm037. Also
remove now unneeded #ifdef CONFIG_I2C_IMX.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-23 14:25:26 +02:00
Alberto Panizzo
0c8bad6a26 Armadillo 500 add NAND flash device support (resend).
Since recent mxc_nand driver fixes from linux-mtd this patch
add support for ST NAND02GW3B2CN6 (2k pages flash) placed on the armadillo 500
motherboard.

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-23 14:25:26 +02:00
Alberto Panizzo
c3a9c7f53a ARM MXC: Armadillo 500 add NOR flash device support (resend).
This patch add support for NOR flash mapping through the physmap driver.
The purpose is to maintain the original Atmark partition model.

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-23 14:25:25 +02:00
Huang Weiyi
bc33dc5ae7 mx31: remove duplicated #include
Remove duplicated #include in arch/arm/mach-mx3/devices.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-23 14:25:25 +02:00
Linus Torvalds
2cf4d4514d Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
  MAINTAINERS: EB110ATX is not ebsa110
  MAINTAINERS: update Eric Miao's email address and status
  fb: add support of LCD display controller on pxa168/910 (base layer)
  [ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
  [ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
  [ARM] 5544/1: Trust PrimeCell resource sizes
  [ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
  [ARM] pxa/sharpsl_pm: drop set_irq_type calls
  [ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
  [ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
  [ARM] sa1100: remove unused collie_pm.c
  [ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
  [ARM] 5550/1: Add default configure file for w90p910 platform
  [ARM] 5549/1: Add clock api for w90p910 platform.
  [ARM] 5548/1: Add gpio api for w90p910 platform
  [ARM] 5551/1: Add multi-function pin api for w90p910 platform.
  [ARM] Make ARM_VIC_NR depend on ARM_VIC
  [ARM] 5546/1: ARM PL022 SSP/SPI driver v3
  ARM: OMAP4: SMP: Update defconfig for OMAP4430
  ARM: OMAP4: SMP: Enable SMP support for OMAP4430
  ...
2009-06-14 13:42:43 -07:00
Russell King
2d8d24935d Merge branch 'mxc-master' of git://git.pengutronix.de/git/imx/linux-2.6 into devel 2009-06-08 19:26:28 +01:00
Rabin Vincent
6b4bfb87b6 mx[23]: don't put clock lookups in __initdata
Remove the __initdata annotation for the clock lookups, since they will
be needed when loading modules which use clk_get().

Tested-by: Agustín Ferrín Pozuelo <gatoguan-os@yahoo.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-03 11:51:06 +02:00
Fabio Estevam
aefa1c6e7b MX35: Add basic support for MX35PDK board
Add basic support for MX35PDK board (www.freescale.com/imx35pdk).

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-03 11:44:50 +02:00
Daniel Mack
8d9fb9bb89 Support for lilly-1131 modules and baseboards [v2]
On Thu, May 28, 2009 at 08:42:23PM +0200, Sascha Hauer wrote:
> > > Mail-Followup-To: Daniel Mack <daniel@caiaq.de>,
> > > 	linux-arm-kernel@lists.arm.linux.org.uk
> >
> > ... which causes my mutt to only reply to the list.
>
> Ah, ok. /me hacking in muttrc... Does it work now?

Yep :)

> >  	mxc_register_device(&mxc_uart_device0, &uart_pdata);
> > +	mxc_register_device(&mxc_uart_device1, &uart_pdata);
> > +	mxc_register_device(&mxc_uart_device2, &uart_pdata);
>
> What about the RXD3/TXD3 pins?

You're right - I got the IOMUX tables wrong and thought UART0 pins are
selected unconditionally. But as it turns out TXD1/RXD1 is for UART0
(mxc_uart_device0), TXD2/RXD2 for UART1 (mxc_uart_device1) etc.

Below is a new patch.

Thanks,
Daniel

From e7eb5fa0fed09d667a4b2f168fe466e2cc645abb Mon Sep 17 00:00:00 2001
From: Daniel Mack <daniel@caiaq.de>
Date: Wed, 27 May 2009 12:22:51 +0200
Subject: [PATCH] ARM: MX3: add two more UARTs to lilly-1131-db

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-02 19:28:36 +02:00
Russell King
a22f277bba [ARM] Kconfig: remove 'default n'
Kconfig entries default to n, so there's no need for this to be
explicitly specified.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-05-31 15:12:25 +01:00
Valentin Longchamp
0573cb5f45 mx31: correct csi_clk parent (v2)
changes since v1: we now check if the parent configuration bit was
changed since reset and change the parent when needed.

csi_clk parent was defined with ahb_clk. However, according to the
m31 reference manual, it should be serial_pll_clk.

Guennadi always used a 20 MHz clock that was by chance changed to
a 45 MHz that fits in the mt9t031 spec. Now the clocks are computed
and output correctly (measured on oscillo).

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-28 17:20:53 +02:00
Fabio Estevam
0b0ef44295 MX3: Add missing entry in devices.h
Add missing mxc_rnga_device entry in devices.h (mxc-master tree).

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-28 17:19:23 +02:00
Alberto Panizzo
4e0f088106 ARM MXC: Atmark Armadillo 500 board support.
On Mon, 25 May 2009 18:33:28 +0200
Valentin Longchamp <valentin.longchamp@epfl.ch> wrote:

> Hello,
>
> I have updated my mxc git tree and given a compilation spin to your
> board support and I have comments. See below.
>

>
> What's the point of declaring this new function, if all it does is
> calling the already existing one ? Furthermore, in the current
> mxc-master tree, mxc_map_io() does not exist anymore, it should be
> mx31_map_io (this breaks compilation for your board).
>

This patch solve those two issues. Until now i based my patches to
vanilla tree. This evening I cloned the mxc-master tree so i could
update the armadillo 500 support within recent platform changes.

The patch:

From e986a8dc262e5292350d95bf65ead75baf3272d7 Mon Sep 17 00:00:00 2001
From: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Date: Mon, 25 May 2009 22:24:03 +0200
Subject: [PATCH] Armadillo 500 removing useless function armadillo5x0_map_io
and use machine specific io mapping

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-26 12:34:11 +02:00
Daniel Mack
4193d2d2d7 ARM: MX3: add I2C support for lilly-1131
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-26 12:31:55 +02:00
Daniel Mack
38160e0b01 ARM: MX3: add NOR flash support for lilly-1131
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-26 12:31:37 +02:00
Daniel Mack
b99238721b ARM: MX3: add framebuffer support for lilly1131-db
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-26 12:31:28 +02:00
Daniel Mack
d0b1eabc7b ARM: MX3: add MMC suuport for lilly1131-db
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-26 12:31:19 +02:00
Daniel Mack
cbaa6ca1f5 ARM: MX3: add lilly-1131 ethernet support
This adds support for the SMSC911x chip found on the lilly-1131 module.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-26 12:31:13 +02:00
Daniel Mack
1bc34f7964 ARM: MX3: add skeleton for lilly-1131 development board
Support code for lilly-1131 is implemented in a module/baseboard
fashion. All code specific to peripherals found on the development board
will go to this file.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-26 12:30:40 +02:00
Daniel Mack
65b1aa13f2 ARM: MX3: basic support for lilly-1131 board
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based
modules. The module needs a baseboard support to work which will be
added in the next patch.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-26 12:30:32 +02:00
Magnus Lilja
2b0c3677bf i.MX31: Add support for LAN9217 on PDK debug board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-19 21:04:41 +02:00
Alberto Panizzo
5e9145edcc Atmark Armadillo 500 board support.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-19 11:24:57 +02:00
Magnus Lilja
135cad366b i.MX31: Add support for the CPLD on PDK Debug board.
The i.MX31 PDK consists of several boards, one of them is a debug
board containing a CPLD which controls some debug leds, switch
buttons, an interrupt chip and an Ethernet controller.
This patch adds support for detecting if the PDK board is present
(during boot) and adds the interrupt chip to the kernel.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-18 08:36:27 +02:00
Magnus Lilja
153fa1d8c6 i.MX31: Restructure UART setup for PDK board.
Restructure UART pin setup in preparation for adding other pins
in later patches.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-16 16:25:04 +02:00
Alberto Panizzo
92ab0a5015 ARM MXC: Make-sure-ipg_per_clk-is-generated-by-ipg_clk-and-not-usb_pll
From ff1fd9d7015d9b9ad3e0df2016d0415e2719747c Mon Sep 17 00:00:00 2001
From: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Date: Fri, 15 May 2009 17:21:21 +0200
Subject: [PATCH] Make sure ipg_per_clk is generated by ipg_clk and not usb_pll

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-16 16:19:02 +02:00
Magnus Lilja
183c7fff50 i.MX31: Add NAND device driver for Litekit board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-16 16:17:40 +02:00
Valentin Longchamp
9c70e227e0 mx31: add camera device
This adds the camera device based on Guennadi's soc_camera architecture
for the mx31.

The proposed init by Guennadi was removed and must be implemented in the
board init file as it contains a lot of board specific info (memory
size, clock speed).

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:21:16 +02:00
Valentin Longchamp
03c13ecc0d mx31moboard: add support for usb OTG device (v3)
This is used on all board of our system, so again this is done in the
mx31moboard.c file.

changes since v2: call to gpio_request added in platform code, and
moved device initialization in baseboard files.

changes since v1: pins are claimed in another patch

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:21:02 +02:00
Sascha Hauer
4f163eb881 mx31: calls to gpio_request moved into platform code
In order to use the gpiolib, we now have to call gpio_request in
the plaform code since it is not done in iomux code anymore.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:20:52 +02:00
Valentin Longchamp
ef754d6358 mx31: remove gpio_request calls from iomux code
Since iomux code is not directly related to gpio on mx31, the calls
to gpio_request are removed from iomux.c file.

These calls have to be done in platform initialization files. The
name of the singe pin call for iomux is also changed to
mxc_iomux_alloc_pin.

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:20:40 +02:00
Sascha Hauer
35c82da0bf MXC qonq: mxc_map_io is now mx31_map_io
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:20:34 +02:00
Guennadi Liakhovetski
eb05bbeb65 ARM: add USB device support to pcm037
Add OTG device definition and resources to i.MX31 and a pure USB device mode
support to the pcm037 board.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:19:50 +02:00
Magnus Lilja
3211705f76 i.MX31: Add ethernet support to i.MX31 Litekit board.
This patch adds the SMSC platform device to the Litekit board.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:18:36 +02:00
Magnus Lilja
a854b8ab98 i.MX31: Add UART1 device to Litekit board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:18:08 +02:00
Valentin Longchamp
45b131a78c mx31moboard: add sdhc support (v3)
This support both sdhc1 and sdhc2 with WP and CD for the marxbot and
devboard mx31moboard baseboards.

sdhc2 is present on both, but is not directly included in the
mx31moboard file because a third baseboard (not supported yet) without
sdhc2 is planned.

Changes since v1: removed pin initialization from init/exit function and
taken different comments into account

Changes since v2: pin initialiation now is done in another patch for all
current mx31moboard pins

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:17:57 +02:00
Valentin Longchamp
4ec6ecc778 mx31moboard: add i2c support (v2)
Changes since v1: all the pins needed for the drivers are claimed in
another patch

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:17:44 +02:00
Valentin Longchamp
56c7a45bee mx31moboard: setup all pins (v2)
As suggested by Sascha, here we setup all the pins that we are using in
the current (and currently reviewed) drivers for mx31moboard system.

changes since v1: changed I2C1 pin names

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:17:35 +02:00
Alan Carvalho de Assis
45001e92d0 i.MX31: Add hw-random for RNGA
This hw-random driver add support to RNGA hardware found
on some i.MX processors.

Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:17:16 +02:00
Valentin Longchamp
220bbcea27 mx31moboard: clean-up of board support
Various improvements (includes in alphabetical order, platform devices
declaration order change, ...)

The pins now are claimed in a single function call from a main table for
every board for a better clarity and to adopt the current agreement for
mx31 devices.

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:17:07 +02:00
Guennadi Liakhovetski
a8df0ee8d8 ARM: framebuffer support for pcm037
Add support for a QVGA Sharp LCD on pcm037.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:16:12 +02:00
Sascha Hauer
cd4a05f9df MXC: rename mxc_map_io to architecture specific versions
This allows us to have more mapping functions for more than one
i.MX architecture in the kernel. As this is the earliest board
specific hook we have, also use it to set the cpu type.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:15:37 +02:00
Sascha Hauer
13e9f61235 pcm037: Add support for UART2
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:15:33 +02:00
Sascha Hauer
76b6ea0aaa MX35: Fix IPU/Framebuffer clock names
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:15:29 +02:00
Sascha Hauer
dddd4a493d pcm037: add SDHC card detection
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:15:26 +02:00
Sascha Hauer
01ac7d584d pcm037: setup all pins at once and not in init functions
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:15:21 +02:00
Sascha Hauer
d16caf69ce i.MX35 clock support: remove automotive path
It is no longer present in newer cores. Unfortunately Freescale decided
to put the bit which decides between automotive clock path and consumer
clock path in the automotive clock path direction. With current code we
cannot detect the core revision, so just remove automotive path completely.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:15:13 +02:00
Sascha Hauer
54df526819 [ARM] MX35: Add PCM043 board support
The PCM043 is a i.MX35 based board from Phytec also known as the
phyCORE-i.MX35.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:15:08 +02:00
Sascha Hauer
bca6ef1e53 MXC: Add iomux support for MX35 SoCs
This iomux is called iomux-v3 in the tree because it is the third known
incarnation of MXC iomuxers. It is not only found on the MX35 but also
on the MX51 and probably others.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-07 16:14:56 +02:00
Mark Brown
0ac402fdaa mx31ads: Mark as having full regulatoion constraints with 1133-EV1 board
This allows the regulator API to power off unused regulators at the end
of init.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-04-16 13:03:56 +02:00