Use the 32-bit register addresses whenever they are non-zero. This
means that the 32-bit addresses are favored over the 64-bit
(GAS) addresses. The 64-bit addresses are only used if the 32-bit
addresses are zero. This change provides compatibility with all
versions of Windows. The worst case that this solves is when both
the 32-bit and 64-bit addresses are non-zero, but only the 32-bit
addresses are actually valid. This appears to happen in some
BIOSes because in this case, Windows uses the 32-bit addresses.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Microsoft website uses 0xCF8-0xD00. Should be 0xCF8-0xCFF (Two
32-bit registers.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
One entry in the protected port table eliminated. Added extra
comments to describe each table entry.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed unused code for dump of args and locals. General cleanup
and splitting of long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Affects PM1 Control register only. When reading the register, zero
the write-only bits as per the ACPI spec. ACPICA BZ 443. Lin Ming.
http://www.acpica.org/bugzilla/show_bug.cgi?id=443
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This interface is no longer necessary. Requests should be validated
on a per-field basis, not on the entire operation region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Protect certain I/O ports from reads/writes. Provides MS
compatibility. New module, hwvalid.c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As per the ACPI specification, preserve (read/modify/write) all
bits that are defined as either reserved or ignored (PM control
control registers only.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Ignored bits must be preserved according to the ACPI spec.
Usually this means a read/modify/write when writing to the
register. However, for status registers, writing a one means
clear the event. Writing a zero means preserve the event (do not
clear.) This behavior is clarified in the ACPI 4.0 spec, and the
ACPICA code now simply always writes a zero to the ignored bit.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added a reader/writer locking mechanism to allow multiple
concurrent namespace walks (readers), but a dynamic table unload
will have exclusive access to the namespace. This fixes a problem
where a table unload could delete the portion of the namespace that
is currently being examined by a walk. Adds a new file, utlock.c
that implements the reader/writer lock mechanism. ACPICA BZ 749.
http://www.acpica.org/bugzilla/show_bug.cgi?id=749
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Incorrect register length mismatch between the 32 and 64 bit
registers in some cases. Code was was checking the wrong pointer
for non-zero, should be looking at the address within the GAS
structure.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split long lines, update comments.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add and deploy constants for the PM status/enable/control
registers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cleanup table header output.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update code for acpi_read_bit_register and acpi_write_bit_register.
Simplified code path, condensed duplicate code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename acpi_get_register and acpi_set_register to clarify the
purpose of these functions. New names are acpi_read_bit_register
and acpi_write_bit_register.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed locking for reads from the ACPI bit registers in PM1
Status, Enable, Control, and PM2 Control. The lock is not required
when reading the single-bit registers. The acpi_get_register_unlocked
function is no longer needed and has been removed. This will
improve performance for reads on these registers. ACPICA BZ 760.
http://www.acpica.org/bugzilla/show_bug.cgi?id=760
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split some long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed some of the extraneous debug prints using the DB_INFO
level. This should make the DB_INFO more useful.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Print input strings and the result (supported or not supported)
for invocations of the _OSI method.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function is only needed on 64-bit host operating systems.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove all instances of this obsolete macro, since it is now a
simple reference to ->common.type. There were about 150 invocations
of the macro across 41 files. ACPICA BZ 755.
http://www.acpica.org/bugzilla/show_bug.cgi?id=755
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added acpi_hw_write_pm1_control. This function writes both of the PM1
control registers (A/B). These registers are different than than
the PM1 A/B status and enable registers in that different values
can be written to the A/B registers. Most notably, the SLP_TYP
bits can be different, as per the values returned from the _Sx
predefined methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This type is the same as TYPE_A. Removed this and all related
instances. Renamed SLEEP_TYPE_A to simply SLEEP_TYPE.
ACPICA BZ 754.
http://www.acpica.org/bugzilla/show_bug.cgi?id=754
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now return AE_BAD_PARAMETER if the input register pointer is
null, and AE_BAD_ADDRESS if the register has an address of zero.
Previously, these cases simply returned AE_OK. For optional
registers such as PM1B status/enable/control, the caller should
check for a valid register address before calling. ACPICA BZ 748.
http://www.acpica.org/bugzilla/show_bug.cgi?id=748
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The PM1B registers are mirrors of the PM1A registers with
different bits actually implemented. From the ACPI specification:
"Although the bits can be split between the two register blocks
(each register block has a unique pointer within the FADT), the bit
positions are maintained. The register block with unimplemented
bits (that is, those implemented in the other register block)
always returns zeros, and writes have no side effects"
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function was writing an optional PM1B status register
twice. The existing call to the low-level acpi_hw_register_write
automatically handles a possibly split PM1 A/B register.
ACPICA BZ 751.
http://www.acpica.org/bugzilla/show_bug.cgi?id=751
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On read, shift B register bits above the A bits. On write,
shift B bits down to zero before writing the B register. New:
acpi_hw_read_multiple, acpi_hw_write_multiple. These two functions now
transparently handle the (possible) split registers for PM1 Status,
Enable, and Control.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enhance the explanations of the various package return types
for clarity.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add new globals for the PM1 status registers (A/B), similar to the
way the PM1 enable registers are handled. Instead of overloading
the FADT Event Register blocks. This makes the code clearer and
less prone to error.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a call to acpi_os_table_override during the installation of a
dynamic table (loaded via the Load or LoadTable AML operators).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed the Flags parameter from several internal functions since
it was not being used.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, the table override mechanism was implemented for the
DSDT only. Now, any table in the RSDT/XSDT can be replaced by
the host OS. (including the DSDT).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add check for invalid handle in acpi_ns_dump_one_object.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
to prevent wrongly overwriting fixmap that still want to use.
ACPI used to rely on low mappings being all linearly mapped and
grew a habit: it never really unmapped certain kinds of tables
after use.
This can cause problems - for example the hypothetical case
when some spurious access still references it.
v2: remove prev_map and prev_size in __apci_map_table
v3: let acpi_os_unmap_memory() call early_iounmap too, so remove extral calling to
early_acpi_os_unmap_memory
v4: fix typo in one acpi_get_table_with_size calling
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
During early boot, ACPI RSDT/XSDT table entries are gathered into the
'initial_tables[]' array. This array is currently statically defined (see
./drivers/acpi/tables.c). When there are more table entries than can be
held in the 'initial_tables[]' array, the message "Truncating N table
entries!" is output. As currently implemented, this message will always
erroneously calculate N as 0.
This patch fixes the calculation that determines how many table entries
will be missing (truncated).
This modification may be used under either the GPL or the BSD-style
license used for Intel ACPI CA code.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
on boot, print out the OSI strings the BIOS uses to query the OS.
To see this output...
build with CONFIG_ACPI_DEBUG
boot with
"acpi.debug_level=4" (ACPI_LV_INFO) (enabled by default)
and
"acpi.debug_level=1" (ACPI_UTILITIES) (default is 0)
example output:
ACPI: BIOS _OSI(Windows 2001) supported
ACPI: BIOS _OSI(Windows 2001 SP1) supported
ACPI: BIOS _OSI(Windows 2001 SP2) supported
ACPI: BIOS _OSI(Windows 2006) supported
ACPI: BIOS _OSI(Linux) not-supported
ACPI: BIOS _OSI(FreeBSD) not-supported
Signed-off-by: Len Brown <len.brown@intel.com>
