flagged_taskfile() is called from execute_drive_cmd()
(the only user) only if args->tf_out_flags.all != 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove duplicate documentation for ide_do_drive_cmd() from
<linux/ide.h>, this function is already documented in ide-io.c.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the spinlock was removed from sa1100_start_tx(), the "flags"
variable becomes redundant. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The receiver status register reports latched error conditions, which
must be cleared by writing to it. However, the data register reports
unlatched conditions which are associated with the current character.
Use the data register to interpret error status rather than the RSR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We were using udelay in the loop on the primary cpu waiting for the
secondary cpu to take the timebase value. Unfortunately now that
udelay uses the timebase, and the timebase is stopped at this point,
the udelay never terminated. This fixes it by not using udelay, and
increases the number of loops before we time out to compensate.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Patch from Daniel Jacobowitz
After delivering a signal (creating its stack frame) we must check for
additional pending unblocked signals before returning to userspace.
Otherwise signals may be delayed past the next syscall or reschedule.
Once that was fixed it became obvious that the ARM signal mask manipulation
was broken. It was a little bit broken before the recent SA_NODEFER
changes, and then very broken after them. We must block the requested
signals before starting the handler or the same signal can be delivered
again before the handler even gets a chance to run.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The result is mostly similar to the original ppc64 version but with
some adaptations for 32-bit compilation.
include/asm-ppc64 is now empty!
Signed-off-by: Paul Mackerras <paulus@samba.org>
This involves some minor changes: a few unused functions that the
ppc32 pci.c provides are no longer declared here or exported;
pcibios_assign_all_busses now just refers to the pci_assign_all_buses
variable on both 32-bit and 64-bit; pcibios_scan_all_fns is now
just 0 instead of a function that always returns 0 on 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
For these, I have just done the lame-o merge where the file ends up
looking like:
#ifndef CONFIG_PPC64
#include <asm-ppc/foo.h>
#else
... contents from asm-ppc64/foo.h
#endif
so nothing has changed, really, except that we reduce include/asm-ppc64
a bit more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-ppc64/imalloc.h is only included from files in arch/powerpc/mm.
We already have a header for mm local definitions,
arch/powerpc/mm/mmu_decl.h. Thus, this patch moves the contents of
imalloc.h into mmu_decl.h. The only exception are the definitions of
PHBS_IO_BASE, IMALLOC_BASE and IMALLOC_END. Those are moved into
pgtable.h, next to similar definitions of VMALLOC_START and
VMALLOC_SIZE.
Built for multiplatform 32bit and 64bit (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Trying to set the priority would just disable the interrupt due to an
incorrect mask used. We rarely use that call, in fact, I think only in
the powermac code for the cmd-power key combo that triggers xmon. So it
got unnoticed for a while.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make sure that userspace passes in enough data when sending a MAD. We
always copy at least sizeof (struct ib_user_mad) + IB_MGMT_RMPP_HDR
bytes from userspace, so anything less is definitely invalid. Also,
if the length is less than this limit, it's possible for the second
copy_from_user() to get a negative length and trigger a BUG().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The following patch fixes a crash caused by attempting to bounce buffer
when an IDE CD-ROM is used on a machine with an IO-MMU. [At least, this
patch fixes things so I can use my IDE CD-ROM behind an ns87415 on a
HP PA-RISC workstation.]
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Calculation of QP capabilities still isn't exactly right in mthca:
max_send_sge/max_recv_sge fields returned in create_qp can exceed the
handware supported limits.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
From: Amit Gud <amitg@calsoftinc.com>
Patch follows from the suggestions by AC and Felipe W Damasio for fixing the
return codes from IDE drivers.
[ bart: fix coding style while at it ]
Signed-off-by: Amit Gud <gud@eth.net>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: Thibaut VARENE <T-Bone@parisc-linux.org>
Cleaning up the hwif without knowing its previous state in pmac.c is a big
and potentially dangerous job, and there seems to be no generic code interface
that would provide either a way to properly release an hwif or to clean it up.
Fixes OOPS for empty PMAC interface and add-on PCI controller.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These drivers do not compile on big endian systems, and parisc
is big endian. Also mark some as broken on m68k as well.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
From: Hanna Linder <hannal@us.ibm.com>
The dev returned from pci_find_device() was not used so it can be
replaced with pci_dev_present(). Compile tested.
Signed-off-by: Hanna Linder <hannal@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mention PA-RISC in NS87415 help. PA-RISC [BCJ]xxx0 workstations come with
NS87415 integrated for their CD-ROM drives.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Depend on GSC, not PARISC. Machines without GSC don't have a MUX.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix compile warning caused by conflicting types of expand_upwards. IA64
requires it to not be static inline, as it's used outside mm/mmap.c
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The structure ide_driver_t have a .owner field which is a duplicate
of .gendriver.owner field (.gen_driver is a struct device_driver).
This patch removes ide_driver_t's owner field.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Support multiple controllers in the via82cxxx IDE driver.
Cable detection and ISA bridge finding have been moved into
their own functions.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This entry adds needless complication to the driver as it requires the use of
global variables to be passed into via_get_info(), making things quite ugly
when we try and make this driver support multiple controllers simultaneously.
This patch removes /proc/via for simplicity.
On 10/13/05, Daniel Drake <dsd@gentoo.org> wrote:
> Per Bart's suggestion, I've created a user-space app which shows identical
> data (and doesn't even rely on the via82cxxx IDE driver).
>
> http://www.reactivated.net/software/viaideinfo/
>
> So, I think we should be clear to drop /proc/ide/via now.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Jeff Garzik pointed me to his code to see how to remove a disk from
the system _properly_. Well, here it is...
Every place we remove disks we are now testing before calling del_gendisk
or blk_cleanup_queue and then call put_disk.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Applications using CCISS_BIG_PASSTHRU complained that the data written
was zeros. The problem is that the buffer is being cleared after the
user copy, unless the user copy has failed... Correct that logic.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
This patch fixes a bug that breaks hpacucli, a command line interface
for the HP Array Config Utility. Without this fix the utility will
not detect any controllers in the system. I thought I had already fixed
this, but I guess not.
Thanks to all who reported the issue. Please consider this this inclusion.
Signed-off-by: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <axboe@suse.de>
Some leftover comments referring to drivers/block that are now block/.
They don't add any information we don't already have, so kill them.
Signed-off-by: Coywolf Qi Hunt <qiyong@fc-cn.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
