Use seq_file for the proc file read/write of snd-page-alloc module.
This automatically fixes bugs in the old proc code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix data corruption triggered by wrong headroom marking order
This is an addendum to commit 0e6e7416 ("IB/mlx4: Handle new FW
requirement for send request prefetching"). We also need to handle
prefetch marking properly for S/G segments, or else the HCA may end up
processing S/G segments that are not fully written and end up sending
the wrong data. This can actually cause data corruption in practice,
especially on systems with relatively slow CPUs (where the HCA is more
likely to prefetch while the CPU is in the middle of writing a work
request into memory).
We write S/G segments in reverse order into the WQE, in order to
guarantee that the first dword of all cachelines containing S/G
segments is written last (overwriting the headroom invalidation
pattern). The entire cacheline will thus contain valid data when the
invalidation pattern is overwritten.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In a desparate attempt to fix the suspend/resume problem on Andrews
VAIO I added a workaround which enforced the broadcast of the oneshot
timer on resume. This was actually resolving the problem on the VAIO
but was just a stupid workaround, which was not tackling the root
cause: the assignement of lower idle C-States in the ACPI processor_idle
code. The cpuidle patches, which utilize the dynamic tick feature and
go faster into deeper C-states exposed the problem again. The correct
solution is the previous patch, which prevents lower C-states across
the suspend/resume.
Remove the enforcement code, including the conditional broadcast timer
arming, which helped to pamper over the real problem for quite a time.
The oneshot broadcast flag for the cpu, which runs the resume code can
never be set at the time when this code is executed. It only gets set,
when the CPU is entering a lower idle C-State.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
device_suspend() calls ACPI suspend functions, which seems to have undesired
side effects on lower idle C-states. It took me some time to realize that
especially the VAIO BIOSes (both Andrews jinxed UP and my elfstruck SMP one)
show this effect. I'm quite sure that other bug reports against suspend/resume
about turning the system into a brick have the same root cause.
After fishing in the dark for quite some time, I realized that removing the ACPI
processor module before suspend (this removes the lower C-state functionality)
made the problem disappear. Interestingly enough the propability of having a
bricked box is influenced by various factors (interrupts, size of the ram image,
...). Even adding a bunch of printks in the wrong places made the problem go
away. The previous periodic tick implementation simply pampered over the
problem, which explains why the dyntick / clockevents changes made this more
prominent.
We avoid complex functionality during the boot process and we have to do the
same during suspend/resume. It is a similar scenario and equaly fragile.
Add suspend / resume functions to the ACPI processor code and disable the lower
idle C-states across suspend/resume. Fall back to the default idle
implementation (halt) instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: suspend: consolidate handling of Sx states addendum
ACPI: suspend: consolidate handling of Sx states.
ACPI: video: remove dmesg spam
ACPI: video: _DOS=0 by default to prevent hotkey hang
What guest drivers?
Cc: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When compiling the Blackfin kernel, checksyscalls.pl will report lots of missing syscalls warnings.
This patch will add some missing syscalls which make sense on Blackfin arch
After appling this patch, toolchain should be rebuilt. Then recompiling the kernel with the new
toolchain.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Add minimum support for the Blackfin relocations, since we don't have
enough space in each reloc. The idea is to store a value with one
relocation so that subsequent ones can access it.
Actually, this patch is required for Blackfin. Currently if BINFMT_FLAT is
enabled, git-tree kernel will fail to compile.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David McCullough <davidm@snapgear.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Cc: Miles Bader <miles.bader@necel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Domain Validation in the SPI transport class is failing on boxes with
damaged cables (and failing to the extent that the box hangs). The
problem is that the first test it does is a cable integrity test for
wide transfers and if this fails, it turns the wide bit off. The
problem is that the next set of tests it does turns wide back on
again, with the result that it runs through the entirety of DV with a
known bad setting and then hangs the system.
The attached patch fixes the problem by physically nailing the wide
setting to what it deduces it should be for the whole of Domain
Validation.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the S0 state be always reported as supported
Signed-off: Frans Pop <elendil@planet.nl>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 34feb2c83b.
Suresh Siddha points out that this one breaks the fundamental
requirement that you cannot free page table pages before the TLB caches
are flushed. The quicklists do not give the same kinds of guarantees
that the mmu_gather structure does, at least not in NUMA configurations.
Requested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Pack vote message and response structures
ocfs2: Don't double set write parameters
ocfs2: Fix pos/len passed to ocfs2_write_cluster
ocfs2: Allow smaller allocations during large writes
Strictly it's only needed for eax.
It actually does a little more than strictly needed -- the other registers
are already zero extended.
Also remove the now unnecessary and non functional compat task check
in ptrace.
This is CVE-2007-4573
Found by Wojciech Purczynski
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes just found that we are missing a compat-ioctl
declaration. The fix is trivial. As previous patches for compat-ioctl,
this should also go to stable.
More info :
http://marc.info/?l=linux-wireless&m=119029667902588&w=2
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4cf92a3c was submitted as a fix for bug #8686 at bugzilla.kernel.org
(http://bugzilla.kernel.org/show_bug.cgi?id=8686). Unfortunately, the fix led to
a new bug, reported by Yoshifuji Hideaki, that prevented association for WEP
encrypted networks that use ifconfig to control the device. This patch effectively
reverts the earlier commit and does a proper fix for bug #8686.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes to sleep initialization in ACPI dropped reporting of supported Sx
states above S3. Fix that and also move S5 init into same file as other Sx.
The only functional change is adding printk() for S4 and S5 cases.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The ocfs2_vote_msg and ocfs2_response_msg structs needed to be
packed to ensure similar sizeofs in 32-bit and 64-bit arches. Without this,
we had inadvertantly broken 32/64 bit cross mounts.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The target page offsets were being incorrectly set a second time in
ocfs2_prepare_page_for_write(), which was causing problems on a 16k page
size kernel. Additionally, ocfs2_write_failure() was incorrectly using those
parameters instead of the parameters for the individual page being cleaned
up.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This was broken for file systems whose cluster size is greater than page
size. Pos needs to be incremented as we loop through the descriptors, and
len needs to be capped to the size of a single cluster.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The ocfs2 write code loops through a page much like the block code, except
that ocfs2 allocation units can be any size, including larger than page
size. Typically it's equal to or larger than page size - most kernels run 4k
pages, the minimum ocfs2 allocation (cluster) size.
Some changes introduced during 2.6.23 changed the way writes to pages are
handled, and inadvertantly broke support for > 4k page size. Instead of just
writing one cluster at a time, we now handle the whole page in one pass.
This means that multiple (small) seperate allocations might happen in the
same pass. The allocation code howver typically optimizes by getting the
maximum which was reserved. This triggered a BUG_ON in the extend code where
it'd ask for a single bit (for one part of a > 4k page) and get back more
than it asked for.
Fix this by providing a variant of the high level allocation function which
allows the caller to specify a maximum. The traditional function remains and
just calls the new one with a maximum determined from the initial
reservation.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Need to null terminate environment. Found by inspection
while looking for similar problems to platform uevent bug
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] ahci: add ATI SB800 PCI IDs
libata-sff: Fix documentation
libata: Update the blacklist with a few more devices
This simplifies signalfd code, by avoiding it to remain attached to the
sighand during its lifetime.
In this way, the signalfd remain attached to the sighand only during
poll(2) (and select and epoll) and read(2). This also allows to remove
all the custom "tsk == current" checks in kernel/signal.c, since
dequeue_signal() will only be called by "current".
I think this is also what Ben was suggesting time ago.
The external effect of this, is that a thread can extract only its own
private signals and the group ones. I think this is an acceptable
behaviour, in that those are the signals the thread would be able to
fetch w/out signalfd.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
we upgraded the kernel of a nfs-server from 2.6.17.11 to 2.6.22.6. Since
then we get the message
lockd: too many open TCP sockets, consider increasing the number of nfsd threads
lockd: last TCP connect from ^\\236^\É^D
These random characters in the second line are caused by a bug in
svc_tcp_accept.
(Note: there are two previous __svc_print_addr(sin, buf, sizeof(buf))
calls in this function, either of which would initialize buf correctly;
but both are inside "if"'s and are not necessarily executed. This is
less obvious in the second case, which is inside a dprintk(), which is a
macro which expands to an if statement.)
Signed-off-by: Wolfgang Walter <wolfgang.walter@studentenwerk.mhn.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ATI/AMD SB800 shares some device IDs with SB700,
and SB800 adds two more device IDs:0x4394,0x4395.
Signed-off-by: henry su <henry.su.ati@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code moved to ioread/iowrite but the comment didn't
Also note a posting issue
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A driver writer from another operating system hinted that
the versions of Yukon 2 chip with rambuffer (EC and XL) have
a hardware bug that if the FIFO ever gets completely full it
will hang. Sounds like a classic ring full vs ring empty wrap around
bug.
As a workaround, use the existing watchdog timer to check for
ring full lockup.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for newest Marvell chips.
The Yukon FE plus chip is found in some not yet released laptops.
Tested on hardware evaluation boards.
This version of the patch is for 2.6.23. It supersedes
the two previous patches that are sitting in netdev-2.6 (upstream branch).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should cause no functional changes in driver behaviour.
There are (too) many revisions of the Yukon 2 chip now. Instead of
adding more conditionals based on chip revision; rerganize into a
set of feature flags so adding new versions is less problematic.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On 100mbit versions, the driver always reports gigabit speed
available. The correct modes are already computed, then overwritten.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The length check for truncated frames was not correctly handling
the case where VLAN acceleration had already read the tag.
Also, the Yukon EX has some features that use high bit of status
as security tag.
Signed-off-by: Pierre-Yves Ritschard <pyr@spootnik.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Initialization of ohci1394 was broken according to one reporter if the
driver was statically linked, i.e. not built as loadable module. Dmesg:
PCI: Device 0000:02:07.0 not available because of resource collisions
ohci1394: Failed to enable OHCI hardware.
This was reported for a Toshiba Satellite 5100-503. The cause is commit
8df4083c52 in Linux 2.6.19-rc1 which only
served purposes of early remote debugging via FireWire. This
functionality is better provided by the currently out-of-tree driver
ohci1394_earlyinit. Reversal of the commit was OK'd by Andi Kleen.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add the DIS_EARLY_DAC PHY workaround for 5709 A1. Without it, link
sometimes does not come up.
Update version to 1.6.5.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes pppol2tp_xmit call skb_cow_head so that we don't modify
cloned skb data. It also gets rid of skb2 we only need to preserve the
original skb for congestion notification, which is only applicable for
ppp_async and ppp_sync.
The other semantic change made here is the removal of socket accounting
for data tranmitted out of pppol2tp_xmit. The original code leaked any
existing socket skb accounting. We could fix this by dropping the
original skb owner. However, this is undesirable as the packet has not
physically left the host yet.
In fact, all other tunnels in the kernel do not account skb's passing
through to their own socket. In partciular, ESP over UDP does not do
so and it is the closest tunnel type to PPPoL2TP. So this patch simply
removes the socket accounting in pppol2tp_xmit. The accounting still
applies to control packets of course.
I've also added a reminder that the outgoing checksum here doesn't work.
I suppose existing deployments don't actually enable checksums.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function pppol2tp_recv_core doesn't handle non-linear packets properly.
It also fails to check the remote offset field.
This patch fixes these problems. It also removes an unnecessary check on
the UDP header which has already been performed by the UDP layer.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of UDP-Lite we need to refine the socket check so
that only genuine UDP sockets are allowed through.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
